EC N_0-Sys err
Axis control system error:
1. a manual axis reset has been commanded, but the NC does not respond;
2. a manual axis stop jog has been commanded, but the NC does not respond;
3. an NC axis reset has been commanded, but the NC does not respond;
4. axis enabling has been commanded, but the NC does not respond.
ECN_1 - Machine not zeroed
An attempt to execute a program when the machine has not been zeroed. Press Stop and reset, carry out the zeroing and repeat.
ECN_2 - Machine already in start
Program start with machine already in automatic mode, Warning message.
ECN_3 - Press Stop+Reset
Operations requested not permitted, Warning message.
ECN_4 - Encoder checking routine KO
The axis encoder checking routine has detected an error. Switch the machine off and back on and repeat the resets.
ECN_5 - Quantity >= pieces produced
Start command for a work list line with quantity of pieces produced greater than or equal to the quantity of pieces to be produced.
ECN_6 - Impossible to work (cen) (slot)
The program being carried out on the centre (cen) requires a process to be performed with the slot (slot) which is considered impossible; the possible circumstances are:
1. cutting with C axis without blade aggregate mounted on the active TP;
2. boring with C axis on plane other than XY (plane 5);
3. boring with C axis without boring aggregate mounted on the active TP;
4. processing on plane 5C without boring aggregate mounted on the active TP.
Check the program and retry.
ECN_7 - Too many active slots
Attempt to perform operation on non-existent TP; the possible circumstances are:
MACHINE INTERFACE ERRORS
BIESSE S.p.A. Woodworking Machinery
0408e02f.fm - biesse120100
1. instruction M for unloading of non-existent TP.
Check the program and retry.
ECN_8 - Jog impossible without selecting axes
Attempt to move an axis in jog mode without first having selected it (<ENTER> on the icon).
ECN_9 - Cannot change parameters: axes active
It is not possible to change the axis parameters when they are active. Press Stop and Reset and retry.
ECN_10 - Axis acceleration = 0 (cen) (ax)
For axis (ax) of the centre (cen), the acceleration machine item of data = 0. Not permitted, change the machine item of data.
ECN_11 - Axis over software DW limit stop (ax)
The program being carried out requires the axis (ax) to move over the software DW limit stop. Check the program and retry.
ECN_12 - Axis over software UP limit stop (ax)
The program being carried out requires the axis (ax) to move over the software UP limit stop. Check the program and retry.
ECN_13 - Axis alarm
The NC has switched one or more axes to alarm status and so the PLC has switched the machine to emergency status. Supply power to the system and give the command for a total reset.
ECN_14 - inverter type not allowed (inv)
The type of the inverter (inv) declared in the plc table "PLC_INV" is not amongst those envisaged and controlled by the PLC. Check the item of data concerned.
ECN_15 - Router rotation out of range (inv)
The operating speed of the router controlled by the inverter (inv) exceeds the tolerance of 10% of the desired speed.
ECN_16 - Time for reaching inverter operating speed (inv)
The router piloted by the inverter (inv) does not reach the required rotation speed. The machine stops.
ECN_17 - Time exceeded inverter stopped (inv)
The router piloted by the inverter (inv) does not reach the required rotation speed.
ENV_18 - Inverter acceleration ramp = 0 Def. 5.0
Attempt to operate the inverter with acceleration ramp zero; the operation is impossible and by default the PLC uses a ramp of 5 sec. Check the router data and bit data.
ENV_19 - Inverter deceleration ramp = 0 Def. 5.0
Attempt to operate the inverter with deceleration ramp zero; the operation is impossible and by default the PLC uses a ramp of 5 sec. Check the router data and bit data.
ECN_20 - INV error system call (inv)
Attempt to communicate with inverter (inv) has failed.
ECN_21 - INV parameter out of range (inv)
A parameter outside the range has been transmitted to the inverter (inv).
ECN_22 - INV transmission time out (inv)
Attempt to communicate with inverter (inv) has failed.
ECN_23 - INV transmission interrupted (inv)
Attempt to communicate with inverter (inv) has failed.
8
LIST OF ERRORSBIESSE S.p.A. Woodworking Machinery
0408e02f.fm - biesse120100
ECN_24 - INV CheckSum reception error (inv)
Attempt to communicate with inverter (inv) has failed.
ECN_26 - Bit thickness < working depth (cen) (tp)
The program being carried out on the centre (cen) wants to use the TP (tp) in a process having depth greater than the thickness of the bit fitted. Check the program and retry.
ECN_27 - Entry speed = 0 (setting 1 m/min) (cen) (slot)
The program being carried out on the centre (cen) wants to use the slot (slot) in a process having entry speed zero. Warning message: the PLC sets a speed of 1 m/min. Check the program.
ECN_28 - Interpolation speed = 0 (setting 1 m/min) (cen) (slot)
The program being carried out on the centre (cen) wants to use the slot (slot) in a process having interpolation speed zero. Warning message: the PLC sets a speed of 1 m/min.
Check the program.
ECN_29 - LH bit on RH spindle or RHINV (cen) (tp)
The bit mounted on router (tp) of centre (cen) has rotation direction incompatible with that of the spindle. Check the tooling data and retry.
ECN_30 - RH bit on LH spindle or LHINV (cen) (tp)
The bit mounted on router (tp) of centre (cen) has rotation direction incompatible with that of the spindle. Check the tooling data and retry.
ECN_31 - Operation impossible even with slide high (cen) (slot)
The program being carried out on the centre (cen) wants to use the slot (slot) in a process which is impossible even with the slide high, due to the Z dimensions involved. In order to decide what slide stroke to use, the PLC considers the length of the bit, the thickness of the panel, the safety position of the type of process and the TP offset and the DW limit stop of the Z axis. Check the program and the tooling.
ECN_32 - Loading from unreachable TH (tp) (npu)
Loading on the TP (tp) of the tool mounted on the tool holder (npu) has been commanded, but in the machine data of the tool holder the TP is not enabled to use it. Check the program, the magazine data and the tooling.
ECN_33 - Unloading from unreachable TH (tp) (npu)
Unloading on the TP (tp) of the tool mounted on the tool holder (npu) has been
commanded, but in the machine data of the tool holder the TP is not enabled to use it.
Check the program, the magazine data and the tooling.
ECN_34 - Cannot unload: TH not found (tp)
Unloading of the tool mounted on the TP (tp) has been commanded, it is not possible to find the tool holder on which to unload it from the tooling data active. Check the program and the tooling.
ECN_35 - Final radius != Initial radius (cen)
The program being carried out on the centre (cen) wants to make an arc with initial radius different from the final radius; impossible. Check the program.
ECN_36 - Timeout for axis tolerance (cen) (ax)
The latest positioning of the axis (ax) of the centre (cen) does not comply with the tolerance envisaged.
ECN_37 - Arc 3D or with Zi! = Zf impossible on table 5C (cen)
The program being carried out on the centre (cen) wishes to make a 3D arc or an arc with variation in depth (XYZ spiral) on table 5C; this is not possible because the linear axis may be Z or C. Check the program.
MACHINE INTERFACE ERRORS
BIESSE S.p.A. Woodworking Machinery
0408e02f.fm - biesse120100
ECN_38 - Fixed cycle does not exist (cen)
The program being carried to on the centre (cen) wants to make a vertical hole, but the cycle to be used is not specified in the "Bits Cycles" data. Check the "bits cycles" data and retry.
8
LIST OF ERRORSBIESSE S.p.A. Woodworking Machinery
0408e02f.fm - biesse120100