Fieldname Format Description Example
MINI-LINK SAU DATA
2BElement Management User Interface
Fieldname Format Description Example
Far Hop Side ID Text string Far_Hop_Side_ID from NE terminal
properties
Subnet ID Text string Sub-network id of the terminal Description Text string Description from NE terminal properties Traffic Rate
Description Text string Traffic_Rate_Description from NE
terminal properties
Can be:
0 Validity Text string Value 1 if collection valid, 0 otherwise
1
MINI-LINK SAU DATA
Table 10 MINI-LINK SAU Data
Fieldname Format Description Example
Terminal ID Text string ID of the MINI-LINK Terminal 001A
Equipment Type Text string The type of equipment MLE_SAU
IDS In Own AMM Text string List of terminal IDs in the own AMM 001A-001B-501A
NCC AM No Text string Expanded NCC AM number Can be also
INACTIVE IDs In Connected EAC Text string List of terminal IDs connected to the
EAC (External Alarm Channel) bus at the same site
A001-C001
IDS In Connected
AMM Text string List of terminal IDs available on
expanded NCC
001A-001B-501A IDS In Connected RTU Text string List of connected E_Micro terminal
IDs E05B-E04B
Can be:
NA ON RAC1 Active Text string Indicates if the RAC1 (Remote Alarm
Channel) is enabled
OFF RAC1 Remote ID Text string Terminal ID of the SAU at the
far-end of the RAC
Can be:
RAC1 Interface Text string Type of interface
RS232 or G.703 Can be:
NA ON RAC2 Active Text string Indicates if the RAC2 (Remote Alarm
Channel) is enabled
OFF RAC2 Remote ID Text string Terminal ID of the SAU at the
far-end of the RAC
Can be:
RAC2 Interface Text string Type of interface
RS232 or G.703 User1 I\O Config Text string User Input port configuration
<Type of port (always IN)> -
User IN - Status : NO - Sev. : critical
ServiceOn Microwave Element Manager - Operator Guide 2BElement Management User Interface
Fieldname Format Description Example
Status : <(NO/NC)> - Sev. :
<Severity for the User Input>
NO = Normally Open NC = Normally Closed
User2 I\O Config Text string User Input port configuration Format as described in User1_IO_Config
User3 I\O Config Text string User Input port configuration Format as described in User1_IO_Config
User4 I\O Config Text string User Input port configuration Format as described in User1_IO_Config
User5 I\O Config Text string User Input port configuration Format as described in User1_IO_Config
User6 I\O Config Text string User Input port configuration Format as described in User1_IO_Config
User7 I\O Config Text string User Input port configuration Format as described in User1_IO_Config
User8 I\O Config Text string User Input port configuration Format as described in User1_IO_Config User9 I\O Config Text string User Input/output port configuration
IN:
<Type of port (IN)> - Status :
<(NO/NC)> - Sev. : <severity for the User Input>
OUT:
<Type of port (OUT)> - Status :
<(NO/NC)> - Source <(A-alarm, B-Alarm, A or B Alarm - P-mark - remote)>
NO = Normally Open NC = Normally Closed
ServiceOn Microwave Element Manager - Operator Guide 2BElement Management User Interface
Fieldname Format Description Example
User9_IO_Config
User11 I\O Config Text string User Input/output port configuration Format as described in
User9_IO_Config User12 I\O Config Text string User Input/output port configuration
IN:
<Type of port (IN)> - Status :
<(NO/NC)> - Sev : <severity for the User Input>
OUT:
<Type of port (OUT)> - Status :
<(NO/NC)> - Source Remote NO = Normally Open
NC = Normally Closed
Digital Service Channel1_1
Text string Digital Service Channel configuration:
ID <Terminal id on digital service channel 1> - Alm : <service channel alarm (ON/OFF)> - Conn
<connection point for the service channel>
ID E00a - Alm : ON - Conn. xxx
Digital Service Channell_2
Text string Digital Service Channel configuration:
Format as described in Dig_Service_Chan1_1
Digital Service
Channel1_ 3 Text string Digital Service Channel configuration:
Format as described in Dig_Service_Chan1_1
Digital Service
Channel1_ 4 Text string Digital Service Channel configuration:
Format as described in Dig_Service_Chan1_1
Digital Ana Service
Channel2_ 1 Text string Service channel configuration Digital:
ID <Terminal id on digital service Analog:
ServiceOn Microwave Element Manager - Operator Guide 2BElement Management User Interface
Fieldname Format Description Example
channel 2> - Alm : <service channel alarm> - Conn <connection point for the service channel>
Analog (SAU exp 2 only):
ID <Terminal id on analog service channel 2> -Conn. <Connect terminal on analog service channel on/off> - Tel. <Telephone. Number>
- Conn BR1 : <ON/OFF> - BR1 Out
< output level on the branching port>- Conn BR2 : <ON/OFF> - BR2 Out < output level on the branching port>
Digital Ana Service Channel2_ 2
Text string Service channel configuration Format as described in
Dig_Ana_Service_Chan2_1
Digital Ana Service Channel2_ 3
Text string Service channel configuration Format as described in
Dig_Ana_Service_Chan2_1
Digital Ana Service
Channel2_ 4 Text string Service channel configuration Format as described in
Dig_Ana_Service_Chan2_1
Site ID Text string Site_ID from NE terminal properties Hop Side ID Text string Hop_Side_ID from NE terminal
properties
Hop ID Text string Hop_ID ID from NE terminal
properties
Far Hop Side ID Text string Far_Hop_Side_ID from NE terminal
properties
Subnet ID Text string Sub-network id of the terminal Description Text string Description from NE terminal
properties
Traffic Rate
Description Text string Traffic_Rate_Description from NE
terminal properties
Can be:
0 Validity Text string Value 1 if collection valid, 0
otherwise
1
MIN-LINK E MICRO DATA
Table 11 MINI-LINK E Micro Data
Fieldname Format Description Example
Terminal ID Text string ID of the MINI-LINK Terminal E00A