♦ The PCTEL MX scanner must not be added to Nemo Outdoor before the scanner LED turns green. During the scanner start-up process the LED is amber. If the scanner is added to Nemo Outdoor in the middle of the start-up process, it can cause Nemo Outdoor to crash.
∇ Starting the GPS:
With the PCTEL LX WCDMA scanner you can use either the GSP receiver integrated into the scanner or an external GPS. See page 63 for instructions on how to enable the integrated GPS receiver.
♦ Note that you cannot use both the integrated and an external GPS receiver at the same time.
♦ Note that with the PCTEL LX GSM/WCDMA scanner the Internal GPS receiver should be activated only in UMTS mode.
♦ To be able to make Top-N preamble scanning the scanner receiver must acquire a GPS fix at least 30 seconds before starting the Nemo Outdoor application in online mode.
If the existing configuration file includes a PCTEL WiMAX scanner, it is advised to open the configuration file in offline mode. If scanner does not send any results after 30 seconds, it is advised to send a reset command to the scanner via the user
interface.
From the Measurement menu, select Add New Device.
1.
Click on GPS.
2.
From the list, select the GPS model that you have connected to the PC and click Next.
3.
The GPS Properties dialog is opened. Set the parameters (see the GPS User Manual for 4.
instructions). They should be correct by default. Click OK. The view will return to the Nemo Outdoor main window.
In the Device Status window a green light should be blinking. This means that the GPS is 5.
working properly.
∇ Starting the PCTEL MX/LX/EX/PCT/EXflex/IBflex GSM/WCDMA/1xEVDO/LTE scanner:
Start Nemo Outdoor. Do not load any previous device configuration if asked.
1.
From the Measurement menu, select Add New Device.
2.
Click on Scanner.
3.
From the list of scanners, select the appropriate handler according to the following table, and 4.
click Next.
Scanner Handler
PCTEL LX GSM 1800 PCTEL LX GSM 1800
PCTEL LX GSM 1900 PCTEL LX GSM 1900
Page 60
Scanner Handler
PCTEL LX GSM 850 PCTEL LX GSM 850
PCTEL LX GSM 850/1900 PCTEL LX GSM 850/1900
PCTEL LX GSM 900 PCTEL LX GSM 900
PCTEL LX GSM 900/1800 PCTEL LX GSM 900/1800
PCTEL LX UMTS 1700/2100 PCTEL LX UMTS 1700/2100
PCTEL LX UMTS 1900 PCTEL LX UMTS 1900
PCTEL LX UMTS 2100 PCTEL LX UMTS 2100
PCTEL LX UMTS 850/1900 PCTEL LX UMTS 850/1900
PCTEL LX UMTS 850 PCTEL LX UMTS 850
PCTEL LX CDMA/EVDO 850 PCTEL LX EVDO 800
PCTEL LX 1xEVDO 450 PCTEL LX EVDO 450
PCTEL LX 1xEVDO 850 PCTEL LX EVDO 800
PCTEL LX 1xEVDO 1900 PCTEL LX EDVO 1900
PCTEL LX 1xEVDO 800/1900 PCTEL LX EDVO 800/1900
PCTEL EX CDMA/EVDO 850/1900 PCTEL EX CDMA2000 850/1900 EVDO 850/1900
PCTEL EX GSM 850/1900 & WCDMA 850/1900 PCTEL EX GSM 850/1900 UMTS 850/1900
PCTEL EX GSM 900/1800 & WCDMA 850/2100 PCTEL EX GSM 900/1800 UMTS 850/2100
PCTEL EX GSM 900/1800 & WCDMA 900/2100 PCTEL EX GSM 900/1800 UMTS 900/2100
PCTEL EX GSM 900/1800 & WCDMA 2100 PCTEL EX GSM 900/1800 UMTS 2100 PCTEL EX GSM 1900 & WCDMA 2100 AWS PCTEL EX GSM 1900 UMTS AWS
PCTEL EX WIMAX PCTEL EX WIMAX
PCTEL EX 900/1800 WCDMA/TD-SCDMA 2000 PCTEL EX 900/1800 UMTS TDSCDMA 2000
PCTEL EX WCDMA 2100 AWS&GSM 850/ 1900 PCTEL EX GSM 850/1900 UMTS AWS
PCTEL EX LTE 700ABC PCTEL EX LTE 700ABC
Page 61
Scanner Handler
PCTEL EX LTE 700ABC/Upper 700C/AWS PCTEL EX LTE 700ABC/Upper 700C/AWS
PCTEL EX LTE 700C PCTEL EX LTE 700C
PCTEL EX LTE 700D PCTEL EX LTE 700D
PCTEL EX LTE AWS/700BC PCTEL EX LTE AWS/700BC
PCTEL EX LTE AWS/700C PCTEL EX LTE AWS/700C
PCTEL EX LTE 800 PCTEL EX LTE 800
PCTEL EX LTE 800/2600 PCTEL EX LTE 800/2600
PCTEL EX LTE 1600 PCTEL EX LTE 1600
PCTEL EX LTE 1800/2600 PCTEL EX LTE 1800/2600
PCTEL EX LTE 2100 PCTEL EX LTE 2100
PCTEL EX LTE 2100/2600 PCTEL EX LTE 2100/2600
PCTEL EX LTE 2600 PCTEL EX LTE 2600
PCTEL EX LTE AWS PCTEL EX LTE AWS
PCTEL EX Mini series scanners:
WCDMA 2100 PCTEL EX UMTS 2100
WCDMA 850/1900 PCTEL EX UMTS 850/1900
WCDMA 900/2100 PCTEL EX UMTS 900/2100
WCDMA AWS PCTEL EX UMTS AWS
PCTEL EXFLEX PCTEL EXFLEX
PCTEL IBFLEX PCTEL IBFLEX
PCTEL MX PCTEL MX
PCTEL PCT GSM 900/1800 PCTEL PCT GSM 900/1800
PCTEL PCT UMTS 2100 PCTEL PCT UMTS 2100
Page 62
In the Device Configuration dialog, set the COM Port to the port the scanner is connected to.
5.
With MX, EXflex and IBflex scanners, select the PCTEL USB item.
Set the baud rate to the one used by the scanner and click OK. The dialog will be closed and the 6.
scanner should now be connected to the system.
If the dialog did not close, the start-up did not succeed. Check the cable connections and the 7.
settings and try again.
From the View menu activate Device Status. A check mark will appear next to the command 8.
when it is activated.
A green light on the PCTEL scanner in the Device Status window should be blinking. This 9.
means that the device is working properly and scanning using the default settings. See chapter Starting Measurement (page Error! Bookmark not defined.) for instructions on making your own scanner configuration.
Page 63
∇ Enabling integrated GPS receiver for PCTEL LX WCDMA/PCTEL EX WiMAX scanner
After the PCTEL LX scanner is connected and activated in Nemo Outdoor, open the 1.
Measurement Properties dialog by selecting Measurement | <device> | General Properties.
In the Measurement Properties dialog click the Advanced button.
2.
In the Advanced Properties dialog, select Yes for the Enable Integrated GPS Receiver 3.
option and click OK.
The integrated GPS receiver is now enabled.
4.
♦ Note that you cannot use both the integrated and an external GPS receiver at the same time.
♦ Note that with the PCTEL LX GSM /WCDMA scanner the Internal GPS receiver should be activated only with UMTS mode.
♦ To be able to make Top-N preamble scanning the scanner receiver must acquire a GPS fix at least 30 seconds before starting the Nemo Outdoor application in online mode.
If the existing configuration file includes a PCTEL WiMAX scanner, it is advised to open the configuration file in offline mode. If scanner does not send any results after 30 seconds, it is advised to send a reset command to the scanner via the user
interface.
Page 64
∇ Starting the PCTEL LX GSM/WCDMA dual-mode scanner
Start Nemo Outdoor. Do not load any previous device configuration if asked.
1.
From the Measurement menu, select Add New Device.
2.
Click on Scanner.
3.
From the list select PCTEL LX GSM 900/1800 and click Next.
4.
In the Device Configuration dialog, Port field you should see two consecutive COM ports (e.g., 5.
COM 3 and COM 4). Select the COM port with the smaller number and click OK.
From the Measurement menu, select Add New Device. Click on Scanner.
6.
From the list select PCTEL LX UMTS 2100 and click Next.
7.
In the Device Configuration dialog, Port field you should see two consecutive COM ports (e.g., 8.
COM 3 and COM 4). Select the COM port with the bigger number and click OK.
A green light should be blinking in the Device Status for both devices. This means that the 9. devices are working properly and scanning using the default settings. If the status field displays,
Device is not started, check that you are in online mode (click the Work Offline/Online button ).
The GSM and UMTS scanners will appear as separate devices and must be configured 10.
individually.
∇ Enabling integrated GPS receiver for PCTEL LX GSM/WCDMA dual-mode scanner
♦ Note that with the PCTEL dual-mode scanner the integrated GPS receiver needs to be enabled only for one scanner.
Page 65
After the PCTEL LX scanners are connected and activated in Nemo Outdoor, open the 1.
Measurement Properties dialog by selecting Measurement | <device> | General Properties.
In the Measurement Properties dialog click the Advanced button.
2.
In the Advanced Properties dialog, select Yes in the Enable Integrated GPS Receiver 3.
option and click OK.
The integrated GPS receiver is now enabled.