03005 078296 A Thin Image pool cannot be created because there are not enough resources depending on cache management devices.
Delete resources requiring cache management (external volumes, virtual volumes, and P-VOLs of Thin Image pairs) so that the total number of resources is less than or equal to 55,040, and then retry the operation.
If this problem persists, call the Support Center.
W
03005 078298 The specified volume cannot be
set as a pool volume. Verify the requirements for the pool
volume. W
03005 078305 The operation cannot be performed because the pool volume with a system area is blocked.
Restore the blocked status of the pool volume with a system area, and then retry the operation.
W
03005 106105 The operation cannot be done because the specified pool has no monitoring data.
Check the status of the pool, and then
retry the operation. W
03005 106107 The operation cannot be done because there is only one tier in the specified pool.
Check the configuration of tier in the
pool. W
Part Code
Error Numbe
r Error Message Recommended Action Severity
Level 03010 001046 The number of Cache
Residency settings has exceeded the maximum number of available Cache Residency areas.
Reduce the number of Cache Residency settings, then retry the operation.
W
Part Code
Error Numbe
r Error Message Recommended Action Severity
Level 03022 105131 SSID cannot be allocated to all
the LDEVs with the specified initial SSID.
Check the setting(s). W
03022 105132 Short of %d LDEV ID(s). Check the setting(s). W 03022 105133 The processing cannot continue
due to an internal logic contradiction.
Execute refresh. E
Code r Level
03022 105134 The specified LDEV does not exist in the configuration.
Execute refresh. E
03022 105135 The selected LDEV has an LUN
path setting. Check the setting(s). W
03022 105136 The specified LDEV is a pool volume.
Check the setting(s). W
03022 105137 The selected LDEV has an LDEV
Security setting. Check the setting(s). W
03022 105138 The specified LDEV is a reserved volume of Volume Migration.
Check the setting(s). W
03022 105139 The selected LDEV has been set to a LUSE volume.
Check the setting(s). W
03022 105140 The specified LDEV is a remote
command device. Check the setting(s). W
03022 105141 The selected LDEV has been set as a journal volume.
Check the setting(s). W
03022 105142 The selected LDEV has been set
as a quorum disk volume. Check the setting(s). W 03022 105143 The selected LDEV has an
access attribute setting.
Check the setting(s). W
03022 105144 An LDEV whose emulation type
is OPEN-L is selected. Check the setting(s). W
03022 105145 An LDEV for FICON(R) Data Migration is selected.
Check the setting(s). W
03022 105146 The target LDEV is not
associated with a pool. Execute refresh, then retry the operation. If the same problem persists despite retrying, please call the Support Center.
W
03022 105147 The target LDEV is blocked. Check the setting(s). W 03022 105148 The combo box is not selected. Check the setting(s). W 03022 105149 An error occurred while
accessing the user information.
Execute refresh. E
03022 105150 Select a table. Specify the subject to be operated. W 03022 105151 The processing cannot continue
due to an internal logic contradiction.
Execute refresh. E
03022 105152 An LDEV in Normal or Quick
Formatting status is selected. Check the setting(s). E 03022 105153 The specified value is outside
the range.
Check the setting(s). W
03022 105154 0 cannot be specified. Check the setting(s). W 03022 105155 A value other than the
numerical value is specified. Check the setting(s). W
Code r Level
03022 105156 The processing cannot continue due to an internal logical contradiction.
Execute refresh. W
03022 105159 Multiple rows are selected. Check the setting(s). W 03022 105160 LDEVs with different emulation
types are selected.
Check the setting(s). W
03022 105161 LDEVs with different RAID
levels are selected. Check the setting(s). W
03022 105162 LDEV names cannot be allocated to all the selected LDEVs with the specified numerical value of the Initial Number.
Check the setting(s). W
03022 105163 Insufficient free space to create LDEV.
Check the setting(s). W
03022 105164 LDEVs with different emulation
types are selected. Check the setting(s). W
03022 105165 LDEVs with different RAID levels are selected.
Check the setting(s). W
03022 105166 No more volumes can be created because the free space of the specified parity group is insufficient or the number of LDEVs that can be set has already reached the maximum.
Check the setting(s). W
03022 105167 The specified parity group cannot be set because the emulation type is OPEN-L.
Check the setting(s). W
03022 105168 The selected parity group has no LDEV ID to specify.
Check the setting(s). W
03022 105169 Data in the table is not
selected. Check the setting(s). W
03022 105170 A different parity group is selected.
Check the setting(s). W
03022 105171 The processing cannot continue due to an internal logic
contradiction.
Execute refresh. E
03022 105173 All the check boxes are being
cleared. Specify the subject to be changed with
the check boxes. W
03022 105174 The number of characters for the LDEV name exceeds the maximum (32 characters).
Check the setting(s). W
03022 105175 An invalid character was specified in the LDEV name.
Check the setting(s). W
03022 105176 A value other than the
numerical value was entered in the initial number.
Check the setting(s). W
Code r Level
03022 105177 The specified initial number exceeds nine digits.
Check the setting(s). W
03022 105178 An unblocked LDEV is selected for the target LDEV to be operated.
Check the setting(s). W
03022 105179 An LDEV in Normal or Quick
Formatting status is selected. Check the setting(s). W 03022 105180 The selected LDEV has a
reserved volume setting of Volume Migration.
Check the setting(s). W
03022 105181 Quick formatting cannot be executed because the number of party groups exceeds 36.
Check the setting(s). E
03022 105182 It is not available to change other than the newly allocated SSIDs.
Check the setting(s). W
03022 105183 The same SSID is specified. Check the setting(s). W 03022 105184 Quick formatting cannot be
executed because the number of party groups exceeds 36.
Check the setting(s). W
03022 105185 Pools of different types are specified.
Check the setting(s). W
03022 105186 No more V-VOLs can be added
to the selected pool. Check the setting(s). W
03022 105187 A pool in the abnormal state is selected.
Check the setting(s). W
03022 105188 There is no LDEV ID that can be
set in the selected pool. Check the setting(s). W 03022 105189 An LDEV cannot be added
because the free space in the selected pool is insufficient.
Check the specified value of the subscription limit, then retry the operation.
W
03022 105191 LDEV that has already been set has been selected.
Check the setting(s). E
03022 105192 LDEV not set has been selected. Check the setting(s). E 03022 105193 The number of data patterns
exceeds the setting range. Check the setting(s). W 03022 105194 An error occurred while
formatting.
Execute refresh, then retry the operation. If the same problem persists despite retrying, please call the Support Center.
E
03022 105195 An error occurred while
preparing the quick format. Execute refresh, then retry the operation. If the same problem persists despite retrying, please call the Support Center.
E
03022 105205 Any further, the Pool that selects it cannot set the volume.
Check the setting(s). E
Code r Level
03022 105231 An error occurred in the shredding processing.
Execute refresh, then retry the operation. If the same problem persists despite retrying, please call the Support Center.
E
03022 105232 The same SSID is specified. Specify another unused SSID number. E 03022 105233 The specified number of digits
for SSID is incorrect. Enter the SSID number with 4 digits. E 03022 105248 The processing cannot continue
due to an internal logical contradiction.
Execute refresh. E
03022 105249 Insufficient free space to create LDEV.
Check the setting(s). W
03022 105250 Two or more Basic exists
together to External. Check the setting(s). E
03022 105259 There is no output file. Please operate it again after executing Shredding.
E
03022 105263 An LDEV that the Snapshot is
set has been selected. Check the setting(s). W
03022 105267 Volumes that can be shredded in the selected volumes will be displayed.
Click [OK] to shred. i
03022 105270 The selected status will be canceled because the number of free spaces that exist in the selected parity group exceeds the number that can be set.
Select the free spaces again from the Select Free Space window.
W
03022 105271 The number of free spaces that exist in the selected parity group exceeds the number of volumes that can be set.
Select the free spaces again from the Select Free Space window.
W
03022 105272 Data Output cannot be set
more than 3. Check the setting(s). W
03022 105273 The interruption process cannot be done because there is an unexecuted specified task.
Wait for a while, then retry the operation.
i
03022 105274 The interruption processing was completed.
The task status is changed. Close the window, then check the task status.
i
03022 105275 The current setting exceeds the maximum number of quick formatting that can be executed.
Check the setting(s). i
03022 105279 This functionality is not available. Virtual LVI is required.
Check the setting(s). W
03022 105280 This functionality is not available. Open Volume Management is required.
Check the setting(s). W
Code r Level
03022 105281 There is no LDEV that can be formatted.
Check the setting(s). E
03022 105299 The specified LDEV cannot be used because the user has no access right to a resource group to which the LDEV belongs.
Verify the resources allocation for the user with security administrator role. W
03022 105300 The specified parity group cannot be used because the user has no access right to a resource group to which the parity group belongs.
Verify the resources allocation for the user with security administrator role.
W
03022 105301 The operation cannot be done because the parity group which belongs to a resource group to which the user has no access right includes the specified LDEV.
Verify the resources allocation for the user with security administrator role.
W
03022 105302 The operation cannot be done because the specified parity group contains the LDEV that belongs to a resource group to which the user has no access right.
Verify the resources allocation for the user with security administrator role. W
03022 105308 The operation cannot be done because the specified DP-VOL is included in the pool that belongs to a resource group to which the user has no access right.
Verify the resources allocation for the user with security administrator role.
W
03022 105309 The specified pool cannot be used because the user has no access right to a resource group to which the pool belongs.
Verify the resources allocation for the user with security administrator role. W
03022 105312 Open and mainframe pools cannot be selected at the same time.
Select either open pools or mainframe pools, and then retry the operation.
W
03022 105313 An LDEV cannot be created because the free space that is available to set has already been registered in the task.
Wait until the task is completed, and then retry the operation.
W
03022 105314 In the selected parity group, there is an area where LDEV cannot be made by default.
Select the emulation type or the free space again, and then create an LDEV. W
03022 105435 The TSE volume is created in
blocked status. Wait until the Create LDEVs is completed, and then format the TSE volume.
W
03022 105436 The LDEV that is not in the state of Normal or Quick Formatting is chosen.
Check the setting(s). W
Code r Level
03022 105437 The parity group to be operated contains LDEVs that are not blocked.
Check the setting(s). W
03022 105438 The parity group to be operated contains LDEVs where access attributes are assigned.
Check the setting(s). W
03022 105439 The parity group to be operated contains LDEVs where Pool-VOLs are set.
Check the setting(s). W
03022 105440 The parity group to be operated contains LDEVs where journal volumes are set.
Check the setting(s). W
03022 105441 The parity group to be operated contains LDEVs where quorum disks are set.
Check the setting(s). W
03022 105445 The selected LDEV is an external volume that is mapped for online data migration.
Select a different LDEV. W
03022 105446 The selected parity group contains an external volume that is mapped for online data migration.
Select a different parity group. W
03022 105447 The specified capacity is larger
than the selected free area. Enter a value within the displayed
range. W
03022 105448 No more LDEVs can be created because the selected free area is too small.
Select a different free area. W
03022 105449 No more LDEVs can be created. Verify the device configuration of the storage system.
W
03022 105450 A parity group in which no more LDEVs can be created is included in the selected free area.
Verify the device configuration of the
storage system. W
03022 105451 There are no usable LDEV IDs. Verify the LDEV ID allocation status.
Provide usable LDEV IDs if needed.
W
03022 105452 The number of virtual volumes that can be registered in the storage system has reached the maximum.
Verify the device configuration of the
storage system. W
03022 105453 There are not enough usable LDEV IDs in the selected free area.
Decrease the number of the selected free areas or provide the number of usable LDEV IDs.
W
03022 105454 LDEVs cannot be created in all the free areas.
Decrease the number of the selected free areas.
W
03022 105455 LDEVs cannot be created because there is not enough free area in the pool.
Increase the free area of the pool. W
Code r Level
03022 105456 No more LDEVs can be created in the selected area.
Select a different area. W
03022 105457 The specified LDEV is a TSE
volume. Specify a different LDEV. W
03022 105458 A volume for which the tier relocation is disabled is included.
Enable the tier relocation setting for the volume, or select a different volume for which the setting is enabled.
W
03022 105459 A radio button is not selected. Check the setting(s). W 03022 105460 LDEVs that exceed 4 TB cannot
be used with the following program products:
• ShadowImage
• Copy-on-Write Snapshot
• Thin Image
• TrueCopy
• Universal Replicator
• Volume Migration
• High Availability Manager When TB, GB, or MB is specified as the unit on the window to create LDEVs, an LDEV with a larger capacity than specified may be created due to capacity correction.
See each user guide for details.
To create an LDEV without capacity correction, specify block.
W
03022 105473 Missing %d SSIDs. Check the settings. W
03022 105493 LDEVs that exceed 4 TB cannot be used with the following program products:
• ShadowImage
• Copy-on-Write Snapshot
• Thin Image
• TrueCopy
• Universal Replicator
• Volume Migration
• High Availability Manager When TB, GB, or MB is specified as the unit on the window to expand the capacities of LDEVs, an LDEV with a larger capacity than specified may be created due to capacity correction.
See each user guide for details.
To expand the capacity of an LDEV without capacity correction, specify block.
W
03022 105494 Quick formatting will have an impact on the host I/O performance. Do you want to continue this operation?
See the Provisioning Guide for Open Systems or the Provisioning Guide for Mainframe Systems for the details of quick formatting.
W
Code r Level