03022 107002 The processing cannot continue due to an internal logic
contradiction.
Refresh the window, and then retry the operation. If this problem persists, call the Support Center.
E
Part Code
Error Numbe
r Error Message Recommended Action Severity
Level 03121 105001 The specified Tiering Policy
cannot be set due to one of the following reasons:
• The Tier1 Min value exceeds the Tier1 Max value.
• The Tier3 Min value exceeds the Tier3 Max value.
• The total value of the Tier1 Min value and the Tier3 Min value exceeds 100%.
Check the Tiering Policy setting. W
03121 109205 Are you sure you want to initialize all the DP and TI pools?
To continue, click [OK]. Otherwise,
click [Cancel]. W
Part Code
Error Numbe
r Error Message Recommended Action Severity
Level 03122 105264 The password is invalid. Check the password, then retry the
operation. W
03122 105483 The specified Tiering Policy cannot be set due to one of the following reasons:
• The Tier1 Min value exceeds the Tier1 Max value.
• The Tier3 Min value exceeds the Tier3 Max value.
• The total value of the Tier1 Min value and the Tier3 Min value exceeds 100%.
Check the Tiering Policy setting. W
Code r Level
03122 105485 The selected policy cannot be edited because the policy is defined by the system.
Tiering Policy from the ID 6 and above are available to edit.
W
03122 106005 No more pools can be registered, because the number of registered pools has reached the maximum.
Check the support configuration of pools, then retry the operation.
W
03122 106006 The volume that can be set as a
pool volume does not exist. Check if there is a volume that can be set as a pool volume, then retry the operation.
W
03122 106007 The setting cannot be performed, because the number of pools exceeds the maximum.
Check the support configuration of pools, then retry the operation. W
03122 106008 The volume to be set as a pool volume is not selected.
Specify the volume, then retry the operation.
W
03122 106009 The setting cannot be performed, because the number of pool volumes that can be set to a pool exceeds the maximum.
Reduce the number of selected pool volumes, then retry the operation. W
03122 106010 The specified pool subscription
limit value cannot be set. Check the specified value of the subscription limit, then retry the operation.
W
03122 106011 The number of prefix
characters of the pool name is invalid.
Enter prefix characters with a valid number for the pool name. W
03122 106012 The specified prefix characters for a pool name contain an invalid character(s).
Check the prefix characters of pool name, then retry the operation. W
03122 106013 The initial number of specified
pool name is not input. Check the initial number of pool name, then retry the operation. W 03122 106014 The specified initial number of
pool name contains a character other than the numerical value.
Check the initial number of pool name, then retry the operation.
W
03122 106015 The specified initial number of pool name exceeds the maximum.
Check the initial number of pool name, then retry the operation.
W
03122 106016 The number of characters that can be set for the pool name exceeds the maximum, or some spaces are set.
Check the pool name, then retry the operation.
W
03122 106017 The specified pool name is
already used. Specify another pool name, then retry
the operation. W
03122 106018 The specified pool ID is incorrect.
Check the specified pool ID, then retry the operation.
W
03122 106019 The allocation cannot be done
from the specified pool ID. Specify a pool ID that is smaller than the one specified before, then retry the operation.
W
Code r Level
03122 106021 The selected volumes cannot be specified as a pool volume, because the volume types are different.
Select the same volume type, then retry the operation.
W
03122 106022 The selected volumes cannot be specified as a pool volume, because the cache modes of the selected volumes coexist.
Specify the volumes that have the same cache mode, then retry the operation.
W
03122 106023 The selected volumes cannot be specified as a pool volume, because different CLPRs selected coexist.
Specify the volumes that have the same CLPR, then retry the operation.
W
03122 106024 The operation cannot be executed, because the specified pool is blocked.
Restore the status of the pool, then
retry the operation. W
03122 106025 The operation cannot be executed, because the specified pool is blocked.
Delete the pool. W
03122 106026 The operation cannot be executed, because the pool volume is blocked.
Restore the status of the pool volume, then retry the operation. W
03122 106027 The operation cannot be executed, because the pool usage exceeds the threshold.
Check the usage rate of the pool, then
retry the operation. W
03122 106028 The operation cannot be executed, because the specified pool is in shrinking operation.
Stop the shrinking operation on the pool, then retry the operation. W
03122 106029 The operation cannot be executed, because the specified pool is in Normal status.
Check the status of the pool, then retry
the operation. W
03122 106030 The operation cannot be executed, because the specified pool is associated with a Dynamic Provisioning volume.
Delete the associated Dynamic Provisioning volume, then retry the operation.
W
03122 106031 The operation cannot be executed, because the specified pool is being used.
Check the pool usage, then retry the operation.
W
03122 106032 The operation cannot be executed, because the specified pool is not in shrinking
operation.
Check the status of the pool. W
03122 106033 The operation cannot be performed because the
specified pool is for Thin Image or Copy-on-Write Snapshot.
Check the pool type. W
Code r Level
03122 106034 The shrinking operation cannot be performed on the specified pool due to one of the following reasons.
• The usage rate after shrinking becomes higher than the highest threshold set among the depletion threshold, the warning threshold, and the system threshold.
• There is no pool volume that has enough free space necessary to delete the pool volume with a system area.
Check the following settings, and then retry the operation.
• Pool capacity
• Pool usage capacity
• Depletion threshold value
• Warning threshold value
• System threshold value
• Pool VOL with System Area Capacity
W
03122 106035 The operation cannot be executed, because the top pool volume has been selected.
Select a volume other than the top pool
volume. W
03122 106036 The operation cannot be executed, because the specified pool volumes contain an abnormal pool volume.
Check the state of the specified pool volumes, then retry the operation. W
03122 106037 The setting cannot be
executed, because the specified pool has no free space.
Execute any of the following actions, then retry the operation.
• Increase the pool capacity by adding pool volume(s).
• Reduce the pool usage.
W
03122 106038 No table row, or two or more table rows are selected.
Select one table row. W
03122 106041 There are no valid volumes,
because the pools are blocked. Restore the blocked status of the
pools. W
03122 106042 The shrinking operation cannot be performed on the specified pool.
Check the pool capacity, the maximum reserved capacity, and the current reserved capacity, then retry the operation.
W
03122 106062 The pool cannot be restored. Delete the pool. W 03122 106063 The pool cannot be restored. Execute any of the following actions,
then retry the operation.
• Increase the pool capacity by adding pool volume(s).
• Reduce the pool usage.
W
03122 106064 The pool cannot be restored. Block the pool. W 03122 106077 Four or more drive types cannot
be added to the specified pool. Check the support configuration of pools, then retry the operation. W
Code r Level
03122 106078 The specified function is not available because the
necessary program product is not installed.
Install the necessary program product. W
03122 106080 A volume of different RAID level cannot be specified in the same drive type.
Check the support configuration of pools, then retry the operation. W
03122 106087 The operation cannot be done because there is no pool that can be associated with a Dynamic Provisioning volume (DP-VOL).
Check the specified value of the subscription limit, then retry the operation.
W
03122 106090 The depletion threshold is set lower than the warning threshold.
Check the setting of depletion
threshold and warning threshold, then retry the operation.
W
03122 106091 The warning threshold is not
input. Check the setting of warning threshold, then retry the operation. W 03122 106093 The depletion threshold is not
input.
Check the setting of the depletion threshold, then retry the operation.
W
03122 106094 More than one volume type (drive type, RAID level, or internal/external volume) is used between the LDEVs selected for the pool volumes.
When different volume types are used together in the same pool, the performance will be impacted by the lowest performing volume types.
Confirm that the selected LDEVs with a mix of volume types are OK?
To continue, click [OK]. Otherwise,
click [Cancel]. W
03122 106095 The operation cannot be performed because the tier management of the specified pools is not in manual operation.
Change the tier management of the pool to the manual operation. W
03122 106096 Failed to get the pool
information. Check the status of the pool, and then
retry the operation. W
03122 106097 The operation cannot be done because the specified pool is in monitoring operation.
Check the status of the pool, and then retry the operation.
W
03122 106098 The operation cannot be done because the specified pool is calculating the monitor information.
Check the status of the pool, and then retry the operation.
W
03122 106099 The processing cannot continue due to an internal logic
contradiction.
If the problem persists despite retrying, please call the Support Center.
E
Code r Level
03122 106100 The operation cannot be done because the specified pool is not in the monitoring operation.
Check the status of the pool, and then retry the operation.
W
03122 106101 The operation cannot be done because the configuration of the specified pools does not meet the conditions below.
• The multi tier pool is enabled.
• The tier management is in manual operation.
Check the configuration of the pools. W
03122 106102 The operation cannot be done because the specified pool is in tier relocating operation.
Check the status of the pool, and then
retry the operation. W
03122 106103 The operation cannot be done because the specified pool is in monitoring operation.
Check the status of the pool, and then
retry the operation. W
03122 106104 The operation cannot be done because the specified pool is calculating the monitor information.
Check the status of the pool, and then
retry the operation. W
03122 106105 The operation cannot be done because the specified pool has no monitoring data.
Check the status of the pool, and then retry the operation.
W
03122 106106 The operation cannot be done because the specified pool is not in tier relocating operation.
Check the status of the pool, and then retry the operation.
W
03122 106107 The operation cannot be done because there is only one tier in the specified pool.
Check the configuration of tier in the pool.
W
03122 106108 The specified LDEVs cannot be set as pool volumes in the same pool because the LDEVs are allocated to different resource groups.
Select LDEVs allocated to the same resource group.
W
03122 106111 There is an empty field in the following items.
• Tier Management
• Cycle Time
• Monitoring Period
• Monitoring Mode
• Buffer Space for New page assignment
• Buffer Space for Tier relocation
Check the settings, and then retry the operation.
W
03122 106112 There is no check in the check
box of Multi-Tier Pool. Check the settings, and then retry the
operation. W
Code r Level
03122 106113 The specified pool is not a Dynamic Provisioning pool, a Dynamic Tiering pool, or a Thin Image pool.
Select a Dynamic Provisioning pool, a Dynamic Tiering pool, or a Thin Image pool.
W
03122 106139 This operation will delete the
currently stored monitor data. Verify that the currently stored monitor data can be deleted. If not, cancel the operation.
W
03122 106140 Enabling and disabling the Multi-Tier Pool setting may impact the host I/O
performance of each Dynamic Provisioning volume associated with the pool.
Verify that the pool setting can be changed even if that will impact the host I/O performance. If not, cancel the operation.
W
03122 106163 If the tier configuration changes by performing this operation, the currently stored monitor data will be deleted.
Make sure that there is no problem even if the data is deleted.
W
03122 106164 The operation cannot be
performed with this pool. The operation can be performed with the following pools:
• Dynamic Provisioning
• Dynamic Tiering
W
03122 106165 This operation cannot be performed because the pool volumes are not external LDEVs.
Select only the pool volumes that are external LDEVs, and then retry the operation.
W
03122 106168 A required program product is not installed, or you do not have permission to perform the operation.
Install the required program product, or log off and then log back on with permission to perform the operation.
W
03122 107007 An internal logic error occurred. If the problem persists despite retrying, please call the Support Center.
E
03122 107008 The processing cannot continue due to an internal logic
contradiction.
If the problem persists despite retrying, please call the Support Center.
E
03122 107009 An internal logic error occurred. If the problem persists despite retrying, please call the Support Center.
E
03122 107023 The processing cannot continue due to an internal logic
contradiction.
Refresh the window, and then retry the operation. If this problem persists, call the Support Center.
E
Code r Level