TIME CONST (N)

Address

(bit) Outline N1 Rapid-feed time constant (linear acceleration/deceleration) N2 Cutting-feed time constant (linear acceleration/deceleration) N3 Rapid-feed time constant (First-order lag)

N4 Time constant for post-interpolation rapid feed acceleration/deceleration filter N5 Cutting-feed time constant (First-order lag)

N6 — N7 OT time

N8 Creeping speed during initial zero-point return N9 Amount of grid ignorance during initial zero-point return N10 Grid spacing

N11 —

N12 Rapid-feed backlash N13 Cutting-feed backlash N14 —

N15 Width to which the machine posture change correction is to be applied N16 Machine posture change correction value

N17 Servo amplifier channel number N18 Servo amplifier rotary switch number N19 Axis system number

N20 —

N21 0 Linear-type rotational axis

1 Rotational axis shortcut Invalid/Valid 2 Fixed value (0)

3 Fixed value

4 —

5 —

6 Relative polarity of control axis

7 —

N22 - N29 —

N30 Time constant for cutting feed (for M881) N31 Time constant for cutting feed (for M882) N32 Time constant for cutting feed (for M883) N33 Time constant for cutting feed (for M884) N34 Time constant for cutting feed (for M885) N35 Time constant for cutting feed (for M886) N36 - N44 —

Address

(bit) Outline S1 - S4 —

S5 Rotational center of the table S6 Absolute position detection parameter S7 - S12 —

S13 G00 in-position width S14 G01 in-position width S15 Fixed value

S16 —

S17 Torque limit buffer reduction ratio 1 S18 Torque limit buffer reduction ratio 2 S19 - S22 —

S23 Reference workpiece zero point S24 - S30 —

S31 Specification of the machine coordinates of the floating reference point S32 - S44 —

7.

SPINDLE (SA)

Address

(bit) Outline SA1 - SA8 Maximum RPM of spindle in each speed range (range 1 to 8) SA9 - SA16 Constants for calculating each gear speed of the spindle (range 1 to 8) SA17 - SA24 Maximum RPM of spindle during tapping cycle (range 1 to 8)

SA25 - SA32 Spindle speed during gear shifting (range 1 to 8)

SA33 - SA40 Acceleration/deceleration time constant for the synchronous tapping (range 1 to 8) SA41 Spindle orientating speed

SA42 Minimum spindle speed

SA43 Channel number for the spindle amplifier SA44 Spindle amplifier rotary switch number

SA45 0 Spindle speed range changing method, in relation to switching the torque factors for auto-pecking of the cutting load detection type

1 Spindle speed range changing method, in relation to switching the torque factors for auto-pecking of the cutting load detection type 2

2 Homing direction for synchronous tapping 3 Homing direction for synchronous tapping

4 Defines the specified direction as the Z-phase detection direction 5 Spindle index gear correction

6 —

7 —

SA46 0 Direction of orientation 1 Direction of orientation

2 C-axis position control changeover type

3 Synchronous tapping position control changeover type 4 Z-phase detection direction

5 C-axis homing direction 6 C-axis homing direction

7 Synchronous tapping command polarity SA47 0 — 1 — 2 — 3 — 4 — 5 — 6 —

7 Considering/Ignoring the spindle/motor gear ratio SA48 Encoder signal input destination

SA49 Speed attainment detection width SA50 Spindle type

SA51 Number of gears on spindle SA52 Turning spindle type

SA53 Spindle 1/4h (1/2h) rated torque for auto-pecking of the cutting load detection type — L coils

SA54 Spindle 1/4h (1/2h) rated torque for auto-pecking of the cutting load detection type — H coils

SA55 Spindle 1/4h (1/2h) rated torque for auto-pecking of the cutting load detection type — Spindle gear position 3

SA56 Spindle 1/4h (1/2h) rated torque for auto-pecking of the cutting load detection type — Spindle gear position 4

SA57 Spindle viscous friction coefficient “cms” for auto-pecking of the cutting load detection type — Range 1

SA58 Spindle viscous friction coefficient “cms” for auto-pecking of the cutting load detection type — Range 2

SA59 Spindle viscous friction coefficient “cms” for auto-pecking of the cutting load detection type — Range 3

SA60 Spindle viscous friction coefficient “cms” for auto-pecking of the cutting load detection type — Range 4

SA61 Spindle coulombic friction coefficient “fms” for auto-pecking of the cutting load detection type — Range 1

SA62 Spindle coulombic friction coefficient “fms” for auto-pecking of the cutting load detection type — Range 2

SA63 Spindle coulombic friction coefficient “fms” for auto-pecking of the cutting load detection type — Range 3

SA64 Spindle coulombic friction coefficient “fms” for auto-pecking of the cutting load detection type — Range 4

SA65 Cutting force calculation filter for auto-pecking of the cutting load detection type SA66 Maximum permissible speed of the rotational axis for polygonal machining SA67 - SA86 —

SA87 Spindle speed operating time constant changeover revolutions 1 SA88 Spindle speed operating time constant changeover revolutions 2 SA89 Spindle speed operating time constant 1

SA90 Spindle speed operating time constant 2 SA91 Spindle speed operating time constant 3 SA92 Z-phase detection speed

SA93 Amount of synchronous tapping zero point shifting SA94 Homing speed for synchronous tapping

SA95 Maximum revolutions in manual operation mode SA96 Amount of orientation position shifting

SA97 Reduction ratio of the synchronous tapping time constant for high-speed synchronous tapping SA98 —

SA99 Orientation time constant SA100 -

SA113 —

SA114 Spindle speed supervisory mode 2 for safety supervision SA115 Spindle speed supervisory mode 3 for safety supervision SA116 Spindle safety clamping mode 2 for safety supervision SA117 Spindle safety clamping mode 3 for safety supervision

SA118 Selecting the spindle door of the spindle whose speed is to be monitored

SA119 Deceleration judgment coefficient on safety speed clamping of the spindle to be supervised for safety

SA120 PLG pulse rate for spindle index gear tooth correction

SA121 Amount of branching [1] point correction for spindle index gear tooth SA122 Amount of branching [2] point correction for spindle index gear tooth SA123 Amount of branching [3] point correction for spindle index gear tooth SA124 Amount of branching [4] point correction for spindle index gear tooth SA125 Amount of branching [5] point correction for spindle index gear tooth SA126 Amount of branching [6] point correction for spindle index gear tooth SA127 Amount of branching [7] point correction for spindle index gear tooth SA128 Amount of branching [8] point correction for spindle index gear tooth SA129 #1 notch filter frequency for cutting-load detection pecking cycle SA130 #1 notch filter depth for cutting-load detection pecking cycle SA131 #2 notch filter frequency for cutting-load detection pecking cycle SA132 #2 notch filter depth for cutting-load detection pecking cycle SA133 Breakage detection torque for cutting-load detection pecking cycle SA134 Maximum spindle orientation speed

SA135 -

SA137 —

SA139 Number of motor gears SA140 Turret indexing gear ratio SA141 - SA143 — SA144 0 — 1 — 2 — 3 —

4 Positive threading spindle rotational direction and encoder polarity 5 Gear conversion during spindle rotation valid

6 Spindle gear changeover valid 7 Turret indexing valid

8.

BARRIER (BA)

Address

(bit) Outline BA1 Chuck outside diameter (for chuck barrier)

BA2 Chuck width (for chuck barrier)

BA3 Chuck inside diameter (for chuck barrier) BA4 EIA program workpiece outside diameter BA5 - BA7 —

BA8 Tail body outside diameter (for tail barrier) BA9 Tail body length (for tail barrier)

BA10 Tail spindle outside diameter (for tail barrier) BA11 Length with tail spindle at back end (for tail barrier) BA12 Tail head outside diameter (for tail barrier) BA13 Tail head length (for tail barrier)

BA14 Tail head taper angle (for tail barrier) BA15 Tail head biting diameter (for tail barrier)

BA16 Tail barrier, tail extruding length BA17 Tail barrier, workpiece length BA18 Tail barrier, tail reversing position Z

BA19 Distance from the Z-axis machine zero point to the spindle edge BA20 —

BA21 Jaw number for EIA program barrier BA22 —

BA23 Turret outside diameter (turret type tool post) BA24 Turret width (turret type tool post)

BA25 Turret reference position X (turret type tool post) BA26 Turret reference position Z (turret type tool post) BA27 Tool holder mounting position — Type 1 BA28 Tool holder width in X-axis direction — Type 1 BA29 Tool holder width in Z-axis direction — Type 1 BA30 Tool holder mounting position — Type 2 BA31 Tool holder width in X-axis direction — Type 2 BA32 Tool holder width in Z-axis direction — Type 2 BA33 Tool holder mounting position — Type 3 BA34 Tool holder width in X-axis direction — Type 3 BA35 Tool holder width in Z-axis direction — Type 3 BA36 Tool holder mounting position — Type 4 BA37 Tool holder width in X-axis direction — Type 4 BA38 Tool holder width in Z-axis direction — Type 4 BA39 EIA tool barrier, tool holder mounting position BA40 EIA tool barrier, tool holder width X

BA41 EIA tool barrier, tool holder width Z BA42 Fixed value (1)

BA43 First tool number (in the 1st set of tools) BA44 Number of tools (in the 1st set of tools) BA45 First tool number (in the 2nd set of tools) BA46 Number of tools (in the 2nd set of tools) BA47 Turret type

BA48 - BA54 —

BA55 Turning spindle number for polygonal machining (D1) BA56 Turning spindle number for polygonal machining (D2) BA57 Turning spindle number for polygonal machining (D3) BA58 Turning spindle number for polygonal machining (D4) BA59 Spindle forward rotation M-code for tapping cycle BA60 Spindle reverse rotation M-code for tapping cycle BA61 - BA65 —

BA66 Deceleration area Z

BA67 Measuring area Z BA68 Deceleration area X

BA69 Measuring area X

BA70 Distance between the reference points on both turrets BA71 —

BA72 Feed override for retracting the tap BA73 - BA91 —

BA92 Central position X when viewed from machine zero point BA93 —

BA94 —

BA95 Tool nose measurement, sensor width along the X-axis BA96 Tool nose measurement, sensor width along the Z-axis

BA98 Tool nose measurement, Y-coordinate of the sensor’s reference point BA99 Tool nose measurement, Z-coordinate of the sensor’s reference point BA100 -

BA104 —

BA105 Adjustment “FdT” for servo axis thrust hold BA106 Dead zone

BA107 Filter

BA108 Servo axis thrust hold droop BA109 -

BA123 —

BA124 Fixed value (0)

BA125 0 EIA tailstock barrier, tailstock usage valid/invalid 1 Tailstock present/absent

2 EIA tool barrier, tool holder present/absent 3 Barrier tool nose position (EIA, automatic)

4 Setting of BA11 is handled as tailstock extruding length, valid/invalid

5 Output of spindle revolution M-code specified in same block as synchronous tapping, valid/invalid 6 Alarm stop when [BARRIER CANCEL] menu function is valid at the start of the automatic operation,

valid/invalid

7 Alarm stop when jaw Nos. are not specified at the start of the automatic operation, valid/invalid BA126 0 —

1 —

2 —

3 Tool command scheme

4 —

5 Milling spindle orientation command (M219), output/no output

6 —

7 —

BA127 0 M249 command for preparing for tool change before moving the tool to the tool change position using a MAZATROL program, no output/output

2 Simultaneous output of TTM6M200 and TTM6M202 3 NC tailstock (servo axis thrust control)

4 M90/M91 output for machines with turret

5 —

6 —

7 Whether or not to read the current settings (tailstock position) on the SET UP MANAG. display at the beginning of the execution of each program

BA128 0 NC tailstock pushing direction

1 Method of automatic determination of the virtual nose point for a tool measuring unit

2 — 3 — 4 — 5 — 6 — 7 — BA129 - BA132 —

2-2-3

Data I/O parameter

In document mazak (Page 54-65)