• No results found

Investigation On The Fracture Toughness Of Welded Pressure Vessel Steel

N/A
N/A
Protected

Academic year: 2019

Share "Investigation On The Fracture Toughness Of Welded Pressure Vessel Steel"

Copied!
24
0
0

Loading.... (view fulltext now)

Full text

(1)

UNIVERSITI TEKNIKAL MALAYSIA MELAKA

INVESTIGATION ON THE FRACTURE TOUGHNESS OF

WELDED PRESURE VESSEL STEEL

This report submitted in accordance with the requirement of the Universiti Teknikal Malaysia Melaka (Utem) for the Bachelor Degree of Manufacturing Engineering

(Engineering Material) with Honours.

by

SUHAILY BINTI MOHAMAD YUSOF

(2)

UTeM Library (Pind.1/2007)

UNIVERSITI TEKNIKAL MALAYSIA MELAKA

BORANG PENGESAHAN STATUS LAPORAN PSM

JUDUL:

Investigation on the Fracture Toughness of Welded Pressure Vessel Steel

SESI PENGAJIAN: Semester 2 2008/2009

Saya Suhaily binti Mohamad Yusof____________________________________ mengaku membenarkan laporan PSM / tesis (Sarjana/Doktor Falsafah) ini disimpan di Perpustakaan Universiti Teknikal Malaysia Melaka (UTeM) dengan syarat-syarat kegunaan seperti berikut:

1. Laporan PSM / tesis adalah hak milik Universiti Teknikal Malaysia Melaka dan penulis.

2. Perpustakaan Universiti Teknikal Malaysia Melaka dibenarkan membuat salinan untuk tujuan pengajian sahaja dengan izin penulis.

3. Perpustakaan dibenarkan membuat salinan laporan PSM / tesis ini sebagai bahan pertukaran antara institusi pengajian tinggi.

4.

5. *Sila tandakan () SULIT

TERHAD

TIDAK TERHAD

(Mengandungi maklumat yang berdarjah keselamatan atau kepentingan Malaysia yang termaktub di dalam AKTA RAHSIA RASMI 1972)

(Mengandungi maklumat TERHAD yang telah ditentukan oleh organisasi/badan di mana penyelidikan dijalankan)

(SUHAILY BT MOHAMAD YUSOF) Alamat Tetap:

Lot 107 Kg Kemumin, Pengkalan Chepa,

16100 Kota Bharu, Kelantan

Tarikh: 22 MEI 2009

(EN. MOHAMAD HAIDIR BIN MASLAN)

Cop Rasmi:

Tarikh: 22 MEI 2009

(3)

DECLARATION

I hereby, declared this report entitled “Investigation on the Fracture Toughness of Welded Pressure Vessel Steel” is the results of my own research except as cited in

references.

Signature : ……….

Author’s Name : Suhaily Binti Mohamad Yusof

(4)

APPROVAL

This report is submitted to the Faculty of Manufacturing Engineering of UTeM as a partial fulfillment of the requirements for the degree of Bachelor of Manufacturing Engineering (Manufacturing Material) with Honours. The member of the supervisory committee is as follow:

(5)

ABSTRACT

This report covers the investigation on the fracture toughness of welded pressure vessel steel. Failures occur for many reasons, including uncertainties in the loading or environment, defects in the materials, inadequacies in design, and deficiencies in construction or maintenance. Design against fracture has a technology of its own, and this is a very active area of current research. In this study, fracture toughness test have been conducted for A516 Grade 70 steel and the results has been carried out using K1c calculations for fracture toughness. It is shown that the ductile fracture

occurs by the redirection of the crack propagation from the HAZ to the weld metal. Analysis by optical microcopy and SEM has revealed that the improvement in the toughness, and thus the higher resistance to crack propagation in the HAZ, is due to the presence of a large proportion of fine acicular ferrite. Correlation of the result and failure of pressure vessel phenomenon is also analyzed.

(6)

ABSTRAK

Laporan ini merangkumi kajian ke atas kekuatan retakan terhadap kimpalan tangki keluli bertekanan. Kegagalan yang berlaku adalah disebabkan banyak faktor termasuk ketidakpastian dalam pemuatan atau alam sekitar, kecacatan dalam material, kekurangan dalam rekabentuk dan kekurangan dalam pembinaan atau penyelenggaraan. Rekabentuk pada retakan mempunyai teknologi yang tersendiri dan merupakan kawasan yang sangat aktif untuk penyelidikan semasa. Dalam pengkajian ini, ujian kekuatan retakan telah dijalankan menggunakan keluli ASTM A516- Gred 70 dan hasilnya telah dilakukan kiraan K1c untuk nilai kekuatan retakan.

(7)

DEDICATION

(8)

ACKNOWLEDGEMENT

Bismillahirrahmanirrahim, Assalamualaikum,

(9)

TABLE OF CONTENTS

ABSTRACT i

ABSTRAK ii

DEDICATION iii

ACKNOWLEDGEMENT iv

TABLE OF CONTENT v

LIST OF TABLES viii

LIST OF FIGURES ix

LIST OF ABBREVATIONS, SYMBOLS & NOMENCLATURE xi

1. INTRODUCTION 1

1.1 Introduction 1

1.2 Problem Statement 2

1.3 Objective of Project 3

1.4 Scope of Project 3

2. LITERATURE REVIEW 5

2.1. Pressure Vessel Steel 5

2.2. Fracture Mechanics 6

2.2.1 Linear Elastic Fracture Mechanics (LEFM) 7

2.2.1.1 Irwin Plastic Zone Correction 8

2.2.1.2 Dugdale Approaches 9

2.2.2 Fracture Toughness 10

2.2.2.1 Fracture Toughness Parameters 11

2.2.2.2 Fracture Toughness Testing 13

2.2.3 Elastic Plastic Fracture Mechanics (EPFM) 15

2.2.4 Stress Trixiality and Crack Growth 16

2.3. Welding 17

2.3.1 Fusion Welding Process 17

2.3.2 Distortion and Cracking 18

(10)

2.3.4 Thermal Stress Relief 20

2.4. Submerged Arc Welding 21

2.5. Heat Affected Zone (HAZ) 22

2.5.1. HAZ in Welds 22

2.5.2. Thermal Cycle in HAZ 24

2.5.2.1 Heating Rate 25

2.5.2.2 Peak Temperature 25

2.5.2.3 Cooling Rate 25

2.6. Weldment Microstructure and Properties 26

2.7. Hardness Testing 27

2.7.1. Vickers Hardness Test 28

3. METHODOLOGY 29

3.1. Introduction 29

3.2. Research Design 30

3.3. Material Selection 31

3.3.1 ASTM A516 Grade 70 31

3.4. Sample 33

3.4.1 Weld 33

3.4.2 Post Weld Heat Treatment (PWTH) 34

3.4.3 Sample Preparation 34

3.4.4 Cutting 35

3.4.4.1 Cutting Machine 36

3.5. Fracture Toughness 39

3.5.1 Fracture 40

3.5.1.1 Procedures 40

3.5.1.2 Instron Machine 43

3.5.2 Structure 44

3.5.3 Hardness (Vickers Hardness Test) 44

3.5.4 Tensile 46

(11)

4. RESULT AND DISCUSSION 50

4.1 Tensile Test 50

4.2 Hardness 52

4.2.1 Hardness Result 53

4.2.2 Hardness Graphs 53

4.3 Photographs of Structures 54

4.4 Fractographs 56

4.4.1 Base Metal (BM) 56

4.4.2 Heat Affected Zone (HAZ) 59

4.5 Visual Observation 62

4.6 Fracture Toughness 63

4.6.1 Fracture Toughness Data 64

4.6.2 Fracture Toughness Graph 65

5. CONCLUSION 68

5.1 Conclusion 68

5.2 Suggestions for future work 69

REFERENCES 70

(12)

LIST OF TABLES

3.1 3.2 3.3

4.1 4.2 4.3

Chemical composition of 516- Grade 70 Pressure vessel steel Mechanical properties of 516- Grade 70 Pressure vessel steel

Table 3.3 Chemical composition of BM, HAZ, WM (wt %) of 516- Grade 70 Pressure vessel

Fracture Toughness graph for Comparison between HAZ and BM Tensile Result

Fracture Toughness data for specimens

32 32 32

(13)

LIST OF FIGURES

2.1 Irwin Plastic Zone 9

2.2 Strip Yield Plastic Zone 10

2.3 Independent modes of crack deformation 11

2.4 Fracture toughness varies with the specimen thickness 13

2.5 Specimen fails in a linear brittle manner 14

2.6 Degree of non-linearity as depicted 14

2.7 3D State of stress 16

2.8 Various microstructural zones formed in fusion weld 18

2.9 Sketch of the Submerged Arc Welding process 22

3.1 Research Design Flow Chart 30

3.2 Dimension of material 31

3.3 Sample 34

3.4 Compact test specimen Design that have been used successful for fracture Toughness testing

35

3.5 Specimen Plate 36

3.6 3.7

Vertical Band Saw machine Milling Machine 37 37 3.8 3.9 3.10 3.11 3.12 3.13 3.14a 3.14b 3.15 3.16 3.17 3.18

Specimen after shaped process EDM Wire Cut

Three types of load-displacement behavior in a K1c test

Instron Machine Models 8802 Specimen setup onto the machine Zones on the specimen plate Hardness grid

Illustrations of Hardness graph Vickers Hardness tester

Standard Rectangular Tensile Test Specimens Universal Testing Machines

Scanning Electron Microscope (SEM)

(14)

3.19 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 4.13 4.14 4.15 4.16 4.17 4.18 4.19

Area of fracture surface

Stress-Strain Diagram Hardness Grid position

Hardness Graph at v1 position Hardness Graph at v2 position Hardness Graph at v3 position

Structure of Base Metal (magnification 20X)

Structure of Heat Affected Zone, HAZ (magnification 20X) Structure of Welded (magnification 20X)

Fractograph of Pre crack and Fracture areas, BM (magnification 50X) Fractograph of Pre Cracking, BM (magnification 500x)

Fractograph of Fracture, BM (magnification 500x)

Fractograph of Precrack and Fracture areas, HAZ (magnification 50x) Fractograph of Pre Cracking, HAZ (magnification 500x)

Fractograph of Fracture, HAZ (magnification 500x) Fatigue pre cracking onto specimen

Visual Inspection of specimens

Fracture Toughness graph for Base Metal, BM

Fracture Toughness graph for Heat Affected Zone, HAZ

Fracture Toughness graph for Comparison between HAZ and BM

(15)

LIST OF ABBREVATIONS, SYMBOLS &

NOMENCLATURE

~ – Almost equal to

3D – 3Dimension

a, α – Crack length, includes notch plus fatigue pre-crack

ASME – American Society of Mechanical Engineers

ASTM – American Society for Testing & Materials

BM – Base metal

COD – Crack Opening Displacement

CTOD – Crack tip opening displacement

E – Modulus of elasticity in plane stress

EDM – Electrical Discharge Machining

EDX – Energy dispersive X-ray microanalysis

EPFM – Elastic plastic fracture mechanics

F – Frequency (Hz)

FZ – Fusion zone

G – Energy release rate

HAZ – Heat affected zone

HR – Rockwell hardness number

Hz – Hertz

J – Energy-based estimate of fracture toughness

KI – Stress intensity factor (MPa √mm)

KIC – Plane strain fracture toughness (MPa √mm)

LEFM – Linear elastic fracture mechanics

MARA – Majlis Amanah Rakyat

MPa – Megapascal

MSETsc – MSET Shipbuilding Corporation Sdn. Bhd

PMZ – Partially melted zone

PWHT – Post weld heat treatment

(16)

SAW – Submerged Arc Welding

SEM – Scanning Electron Microscope

SENB – Single edge notched bend

WE – Weld electrode

WM – Weld zone

YFM – Yielding fracture mechanics

γ – Gamma

Δ – Amount of real crack

ρ – Length of plastic zone

(17)

1

CHAPTER 1

INTRODUCTION

1.1 Introduction

A pressure vessel is a closed container designed to hold gases or liquids at a pressure different from the ambient pressure. The pressure differential is potentially dangerous and many fatal accidents have occurred in the history of their development and operation. Consequently, their design, manufacture, and operation are regulated by engineering authorities backed up by laws.

The need to protect the public became apparent shortly after the steam engine was conceived in the late 18th century. In the early 1800s, there were literally thousands of boiler explosions in the United States and Europe, each of which resulted in some deaths and a few injuries. The consequences of these failures were not of a catastrophic level that brought a lot of attention to them. It was not until the failures became more catastrophic that attention was brought to bear on the explosions. Canonico, D. A. (2000).

(18)

2

the weld zone, such as centerline cracks, transverse cracks and micro-cracks in the underlying WM or HAZ.

1.2 Problem Statement

Failures of welded structures can and do occasionally occur, sometimes with serious human, environmental and economic consequences. Study shows approximate failure rates for various types of welded structure. For example the explosion boiler at USA in year 1900 recorded the failure rate is approximately 400 per year and for year 1970 is approximately 200 per year. For onshore gas pipeline at Western Europe traced the failure rate is 0.6 per 1000 km per year while for petroleum products pipeline at USA give the failure rate 0.55 per 1000 km per year.

It shows amongst other things how the use of experience-based engineering codes and standards can reduce failure rate whereas the ASME Boiler Code Committee was established in 1911, when boiler explosions in the USA were occurring at the rate of virtually one per day. Although such occurrences are much less common a century on, the continued prevention of failure requires careful attention to design, materials, construction, inspection and maintenance.

A useful way of categorizing failures in welded structures is to distinguish between instant failure modes and time-dependent failure processes. In all cases, the failure occurs when the 'driving force' for failure for example applied stress that exceeds the materials resistance such as fracture toughness. Consequently, instant failure modes are quite likely to occur early in the life cycle of the structure, perhaps due to errors in design, construction, materials or inspection. Smith, T. A. and Warwick, R. G. (1983).

(19)

3

Discontinuities may be classified as defects depending on acceptance criteria in a particular specification or code. Discontinuities are rejectable only if they exceed specification requirements in terms of type, size, distribution, or location. Discontinuities may be found in the weld metal (WM), heat-affected zones (HAZ), and base metal (BM) of weldments.

These may eventually lead to final failure by one of the instant failure modes described above. Welded joints are particularly susceptible to fatigue, typically initiating from discontinuities at the weld toe. The region affected is called the heat affected zone that lies outside the fusion zone in pure metals and outside the partially melted zone in alloys similar to the area in the undisturbed tank metal next to the actual weld material. Messler, R. W. (1999a). This area is less ductile than either the weld or the steel plate due to the effect of the heat of the welding process. Literature show that HAZ is frequent where damage start to occur. This zone is most vulnerable to damage as cracks are likely to start here. Thus, the zone is uncovered for exposure to influence the serious damage.

1.3 Objectives of project

This research project is to

i. Investigate on the fracture toughness of welded pressure vessel steel. In this project, study will be carried on investigating of fracture toughness properties for each zone of welded pressure vessel steel.

ii. To differentiate the fracture behavior on area which are Base Metal (BM) and Heat Affected Zone (HAZ)

1.4 Scope of project

(20)

4

the weld thermal cycle in the base metal (BM), the heat affected zone (HAZ) and the weld metal (WM). The extent is to differentiate microstructure of base metal zone and heat affected zone on welded structures. Welded structures are subjected to the dynamic loading usually, for example the construction structure during the life cycle on-off. It is necessary to guarantee the base steel and its welded joint for own enough fracture toughness at the loading rate which the structure subjected.

(21)

5

CHAPTER 2

LITERATURE REVIEW

2.1 Pressure Vessel Steel

Pressure vessel steel is defined as a container with a pressure differential between inside and outside. The inside pressure is usually higher than the outside, except for some isolated situations. The fluid inside the vessel may undergo a change in state as in the case of steams boilers, or may combine with other reagents in the case of a chemical reactor. Pressure vessels often have a combination of high pressures together with high temperatures, and in some cases flammable fluids or highly radioactive materials.

In pressure vessel steels, carbon is of prime importance because of it strengthening effect. It also raises the transition temperature, lowers the maximum energy values and widens the temperature range between completely tough and completely brittle behavior. Manganese on the other hand (up to 1.5% improves low temperature properties).

(22)

6

They typically have yield strength of 275 MPa, tensile strengths between 415 and 550 MPa and ductility of 25% EL. A516-Grade 70 is one such kind of steel and has applications in low-temperature pressure vessels. Samit, S. (1998a).

The important mechanical properties for pressure vessel are: i. Yield Strength

ii. Ultimate Strength

iii. Reduction of Area (a measure of ductility) iv. Fracture Toughness

v. Resistance to Corrosion

2.2 Fracture Mechanics

Fracture mechanics is a set of theories describing the behavior of solids or structures with geometrical discontinuity at the scale of the structure. The discontinuity features may be in form of line discontinuities in two-dimensional media such as plates, and shells and surface discontinuities in three-dimensional media. Fracture mechanics has now evolved into a mature discipline of science and engineering and has dramatically changed our understanding of the behavior of engineering materials. One of the important impacts of fracture mechanics is the establishment of a new design philosophy; damage tolerance design methodology, which has now become the industry standard in aircraft design.

(23)

7

the major factor was the combinations of poor weld properties with stress concentrations, and poor choice of brittle materials in the construction.

Of the roughly 2700 liberty ships built during World War II, approximately 400 sustained serious fracture, and some broke completely in two. The Comet accidents in 1954 sparked an extensive investigation of the causes, leading to significant progress in the understanding of fracture and fatigue. In July 1962 the Kings Bridge, Melbourne failed as a loaded vehicle of 45 tones crossing one of the spans caused it to collapse suddenly. Four girders collapsed and the fracture extended completely through the lower flange of the girder, up the web and in some cases through the upper flange. Remarkably no one was hurt in the accident.

Fracture mechanics can be divided into linear elastic fracture mechanics (LEFM) and elastic-plastic fracture mechanics (EPFM). LEFM gives excellent results for brittle-elastic materials like high-strength steel, glass, ice, concrete, and so on. However, for ductile materials like low carbon steel, stainless steel, certain aluminum alloys and polymers, plasticity will always precede fracture. Nonetheless, when the load is low enough, linear fracture mechanics continues to provide a good approximation to the physical reality. The purpose of this lecture is to lecture is to provide a broad picture of the theoretical background to fracture mechanics via stress analysis view point. Wang, C. H. (1996).

2.2.1 Linear Elastic Fracture Mechanics (LEFM)

LEFM applies when the materials undergoes only a small amount of plastic deformation. When characterizing the fracture toughness of these materials they can be evaluated by energy release rate (G), and stress intensity factor (KI), which are

(24)

8

Where σ is equal to the yield strength, ‘a’ is the half crack size and ‘E’ is the modulus of elasticity. The energy release rate can be related to the stress intensity factor by the following formulae:

As state earlier LEFM only applies when very little plastic deformation occurs. To improve the accuracy of this result, several researchers including Irwin; who developed the energy release rate and stress intensity factor. Dugdale, and Barenbatt applied a correction. Irwin corrected for plasticity by assuming the existence of a circular plastic zone ahead of the crack tip. He assumed that the half crack length increases by a factor, rp which represents the radius of the plastic zone. Samit, S.

(1998b).

2.2.1.1 Irwin Plastic Zone Correction

References

Related documents

CD: chronic diseases; CI: confidence intervals; CSSSC: Centre de santé et de services sociaux de Chicoutimi; DBMA: Disease Burden Morbidity Assessment; heiQ: health education

Examples are Mach-Reynolds number simulation in cold hypersonic ground based test facilities, verification and qualification of hot structures of space vehicles in

The modeling workflow for the SSEM consisted of an eight-step process: 1) create mineralogy logs for the reef wells with log crossplots and Schlumberger elemental analysis

Ensure that digital materials maintained as records are stable and fixed both in their content and in their form.. O ne of the great

Preview tracking control for a class of fractional order linear systems Liao and Xie Advances in Difference Equations (2019) 2019 472 https //doi org/10 1186/s13662 019 2403 y R E S E A R

MetaFrame Access Suite USERS INFORMATION Conferencing Manager Password Manager Secure Access Manager Presentation Server.. Citrix MetaFrame

global transformation is an isometric transformation, most local regions are under Euclidean Transformations. Integral Invariant signatures characterize well the local. An

3) We use the diagonal girders. The diagonal girders keep the bubbles properly fixed between the top and bottom reinforcement. Short length diagonal bars are