SPECIFICATIONS FOR LCD MODULE

(1)

SPECIFICATIONS FOR LCD

MODULE

CUSTOMER

MODEL

SC240128001-V01

CUSTOMER

APPROVED

APPROVED BY

CHECKED BY

ORGANIZED BY

Lr.Yin Wf.Luo

ADD：6F. B block of 10 Building Huafeng Technology Park. Fengtang Road

Fuyong town Baoan district Shenzhen Guangdong

TEL：0755-81452160

FAX：0755-81452166

(2)

Specification Revision History

Version Content

Date

(3)

1. PHYSICAL DATA

ITEM STANDARD

VALUE

UNIT

NUMBER OF GRAPHIC

240×128

Mm

MODULE DIMENSION

144×104×12(MAX)

Mm

VIEWING AREA

114×64

Mm

DOT SIZE

0.42×0.42

Mm

DOT PITCH

0.45×0.45

Mm

LCD TYPE

STN/ BLUE/ NEGATIVE/TRANSMISSIVE

DUTY 1/128

VIEWING DIRECTION

6:00

o’clock

BACK LIGHT TYPE

SIDE LIT LED

BACK LIGHT COLOR

WHITE

APPROX. WEIGHT

TBD

G

2. EXTERNAL DIMENSIONS

新图

SinoCrystal (ShenZhen) Tech CO., LTD.

A:

1 21 12 21

(4)

3. BLOCK DIAGRAM

BLA BLK LED BACKLIGHT FG VCC GND V0 VEE POWER CIRCUIT DB0-DB7 /WR /RD /RST CS1 A0 FS LCD PANEL 240 X 128 DOTS CONTROLLER and DRIVER 240 SEG 64 COM 64 COM R

(5)

4. INTERFACE PIN CONNECTIONS

Pin No.

Symbol

Level

Description

1 FG --

Frame

ground

2 GND --

Ground

3 VCC --

Power

supply

voltage

4 V0

--

Adjust port of Power supply for LCD

5 /WR H/L

Write

signal

6 /RD H/L

Read

signal

7 /CS

H/L

Chip select signal

8 A0(C/D) H/L

Register selection input

H: Indicate that D0 to D7 are command

L: Indicate that D0 to D7 are data

9 RES

H/L

Chip reset signal

10-17

DB0-DB7

H/L

8-bit bi-directional data bus

18 FS H/L

Font

select

19 VEE

--

Power supply for LCD

20 BLA --

Backlight

anode

(6)

5. ABSOLUTE MAXIMUM RATINGS

(1) Electrical Absolute Ratings

Note 1: Operator should be grounded during handling LCM

（2）Environmental Absolute Maximum Ratings

Normal Temperature

Wide Temperature

Operating Storage Operating Storage

Item

Min. Max, Min. Max, Min. Max, Min. Max,

Ambient Temperature

0℃ +50℃ -10℃ +60℃ -20℃ +70℃ -30℃ +80℃

Humidity(without condensation)

Note 2,4

Note 3,5

Note 4,5

Note 4,6

Note 2 Ta≦50℃: 80% RH max

Ta>50℃: Absolute humidity must be lower than the humidity of 85%RH at 50℃

Note 3 Ta at -20℃ will be<48hrs at 70℃will be <120hrs when humidity is higher than 75%.

Note 4 Background color changes slightly depending on ambient temperature. This phenomenon is

reversible.

Note 5 Ta≦70℃: 75RH max

Ta>70℃: absolute humidity must be lower than the humidity of 75%RH at 70℃

Note 6 Ta at -20℃ will be <48hrs, at 80℃will be <120hrs when humidity is higher than 75%.

Item Symbol

Min.

Max.

Unit

Note

Power Supply for Logic

VDD

0

5.2 Volt

Note 1

Power Supply for LCD

GND - V0

0

20 Volt

Input Voltage

VI 0

VCC Volt

(7)

6. ELECTRICAL CHARACTERISTICS

DC Characteristics

(GND=0V,VCC=3.3-5V, Ta=25℃)

Item Symbol

Test

Condition

Min.

Typ.

Max.

Unit

Power Supply for Logic

VCC

3.0 -

5.2 Volt

VIH

0.8VCC

-

VCC

Volt

Input Voltage

VIL 0

-

0.15VCC

Volt

VOH

VDD-0.3

- VDD

Volt

Output Voltage

VOL

0 -

0.3 Volt

Ta＝0℃ - -

-

Ta＝25℃ 16.0

18.0

19.0 LCM Recommend LCD Module

Driving Voltage

VLCD

Ta＝50℃ - - -

Volt

IDD

(BL OFF)

-

- -

20 Power Supply Current for LCM

IDD

(BL ON)

-

- -

160 mA

(8)

(9)

7. ELECTRO-OPTICAL CHARACTERISTICS

[Note 1] Definition of Response Time (Tr, Tf)

Conditions:

Operating Voltage : Vop Viewing Angle(θ, φ): 0° , 0°

Frame Frequency : 64 Hz Driving Wave form : 1/N duty, 1/a bias

[Note 2] Definition of Viewing Direction

Item Symbol Condition

Min.

Typ. Max.

Unit

note

θf (12 o’clock)

---

15 ---

θb (6 o’clock)

---

45 ---

θl (9 o’clock)

---

30 ---

Viewing

angle range

θr (3 o’clock)

When Cr 2

≧

--- 30 ---

Degree

Note 2

Note 3

Note 4

Rise Time

Tr

112 Fall Time

Tf

250 mS Note

1 Contrast Cr

VDD-V0=8.7V

Ta=25℃

--- 5.

4 ---

Intensity 90％ 100％ Tr 10％ Tf Non-selected

Conition Selected Conition Non-selectedConition

[positive type] Intensity 90％ 100％ Tr 10％ Tf Non-selected

Conition Selected Conition Non-selectedConition

(10)

[Note 3] Definition of viewing angle

(11)

8. OPERATING PRINCIPLES & METHODS

Command Table

COMMAND

CODE

OPERAND 1

OPERAND 2

FUNCTION

0010 0001

X address

Y address

Set cursor pointer

0010 0010

Data

00H

Set offset register

Register Setting

0010 0100 Low address

High address

Set address pointer

0100 0000 Low address

High address

Set text home address

0100 0001

Columns

00H Set

text

area

0100 0010 Low address

High address

Set graphic home address

Set Control Word

0100 0011

Columns

00H

Set graphic area

1000 x000

OR mode

1000 x001

EXOR mode

1000 x011

AND mode

1000 x100

Text Attribute mode

1000 0xxx

Internal CG ROM mode

Mode Set

1000 1xxx

External CG RAM mode

1001 0000

Display

OFF.

1001 xx10

Cursor ON, blink OFF.

1001 xx11

Cursor ON, blink ON.

1001 01xx

Text ON, graphic OFF.

1001 10xx

Text OFF, graphic ON.

Display mode

1001 11xx

Text ON, graphic ON.

1010 0000

Select one-line cursor.

1010 0001

Select two-line cursor.

1010 0010

Select three-line cursor.

1010 0011

Select four-line cursor.

1010 0100

Select five-line cursor.

1010 0101

Select six-line cursor.

1010 0110

Select seven-line cursor.

Cursor Pattern Select

1010 0111

Select eight-line cursor.

1011 0000

Select Data Auto Write

1011 0001

Select Data Auto Read

Data Auto Read/Write

1011 0010

Reset Auto Read/Write

1100 0000

Data

Data Write and increment Address Pointer

1100 0001

Data Read and increment Address Pointer

1100 0010

Data

Data Write and decrement Address Pointer.

1100 0011

Data Read and decrement Address Pointer

1100 0100

Data

Data Write and Keep Address Pointer

Data READ / WRITE

1100 0101

Data Read and Keep Address Pointer

Screen Peek

1110 0000 Screen

peek

Screen Copy

1110 1000

Screen

copy

1111 0xxxx

Bit Reset

1111 1xxxx

Bit Set

1111 x000

Bit 0

Bit Set/Reset

(12)

1111 x010

Bit 2

1111 x011

Bit 3

1111 x100

Bit 4

1111 x101

Bit 5

1111 x110

Bit 6

1111 x111

Bit 7

NOTE: For more detail information, please refer to the T6963C’s specification.

9. Display Data RAM (DDRAM)

The external RAM is used to store display data (text, graphic and external CG data). With single-scan, text data,

graphic data and external CG data can be freely allocated to the memory area (64 KB max). With dual-scan, LCD-I is

allocated to 0000h to 7FFFh (32 KB max), LCD-II is allocated to 8000h to FFFFh (32-KB Max). Text data, graphic data

and external CG data can be freely allocated in LCD-I. In LCD-II, the same addresses must be allocated as in LCD-I,

except A15. A15 determines selection of LCD-I or LCD-II. It can be used the address-decoded signals 0CE(0000h to

07FFh), 1CE (0800h to 0FFFh) within 4 KB. 0CE and 1CE allow decoding of addresses in the ranges (0000h to 07FFh)

and (0800h to 0FFFh) respectively within a 4-KB memory space.

(13)

10. RELIABILITY

Environmental Test

No.

Test Item

Content of Test

Test Condition

Applicable

Standard

1 High temperature

storage

Endurance test applying the high storage

temperature for a long time.

80 C

200 hrs

---

2 Low temperature

storage

Endurance test applying the low storage

temperature for a long time.

-30 C

200 hrs

---

3 High temperature

operation

Endurance test applying the electric stress

(Voltage & Current) and the thermal stress

to the element for a long time.

70 C

200 hrs

---

4 Low temperature

operation

Endurance test applying the electric stress

under low temperature for a long time.

-20 C

200 hrs

---

5 High temperature 

Humidity storage

Endurance test applying the high

temperature and high humidity storage for a

long time.

70 C , 90 RH

96 hrs

MIL-202E-103B

JIS-C5023

6 High temperature 

Humidity operation

Endurance test applying the electric stress

(Voltage & Current) and temperature 

humidity stress to the element for a long

time.

50 C , 90 RH

96 hrs

MIL-202E-103B

JIS-C5023

7 Temperature

cycle

Endurance test applying the low and high

temperature cycle.

_{-10C  60C}

10 cycles

---

Mechanical Test

8 Vibration

test

Endurance test applying the vibration

during transportation and using.

1022Hz  1.5mmp-p

22500Hz  1.5G

Total 0.5hrs

MIL-202E-201A

JIS-C5025

JIS-C7022-A-10

9 Shock

test

Constructional and mechanical endurance

test applying the shock during

transportation.

50G half sign

wave 1l msedc

3 times of each direction

MIL-202E-213B

10 Atmospheric

pressure test

Endurance test applying the atmospheric

pressure during transportation by air.

115 mbar

40 hrs

MIL-202E-105C

Others

11 Static electricity test

Endurance test applying the electric stress

to the terminal.

VS=800V , RS=1.5 k

CS=100 pF

10 time

MIL-883B-3015.1

Inspection after test: Inspection after 2～4 hours storage at room temperature ,the sample shall be free from defects:

1. Air bubble in the LCD.

2. Sealleak

3. Non-display.

4. Missing segments.

5. Glass crack.

6. Current Idd is twice higher than initial value.

25C

5min.

1 cycle

60C

30min

-10C

30min

(14)

11. QUALITY GUARANTEE

No Item

Criteria

1 inclusions (black spot,

white spot, dust)

(1) round type

diameter mm(a) no of defect

a 0.20 neglect

≦

0.20＜a 0.35 5max

≦

0.35＜a none

(2) linear type

length mm(l) width mm(W) no. of defect

na W 0.03 neglect

≦

l 3 0.03

≦

＜W 0.08 6

≦

3＜l 0.08＜W none

2 scratch

1. scratch on protective film is permitted.

2. scratch on polarizer shall be as follow:

(1) round type

diameter mm(a*) no of defect

a 0.15 neglect

≦

0.15＜a 0.20 2 max

≦

0.20＜a none

(2) linear type

be judged bye 1.-(2) linear type

3 dent

diameter

＜ 1.5mm

4 bubble

not exceeding 0.5mm average diameter is acceptable between glass

and polarizing film

5 pin

hole

(a+b)/2

≦

0.15mm

maximum number: ignored

0.15＜(a+b)/2 0.20mm

≦

maximum number:10

6 dot width

design width ±15%

7 dot

defect

(a+b)/2 0.20mm

≦

maximum number: ignored

0.20＜(a+b)/2 0.3

≦

0mm

maximum number:5

x=width

8 contrast

irregularity(spot)

diameter spec no of defect

a 0.50mm neglect

≦

0.50＜a 0.75 5

≦

0.75＜a 1.00 3

≦

1.00＜a none

9 color tone and uniformity obvious uneven color is not permitted

(15)

12. POWER SUPPLY FOR LCM MODULE

V C C

G N D

V E E

B L A

B L K

5 .0 V

V R (2 0 K -5 0 K )

SC240128001

V 0

13. EXAMPLE

1) Application Ciuruit

/CS

A0

8051 MCU

_LCM

P2.7

P2.0

P0.0-P0.7

/RD

P3.7

/WR

P3.6

/RST

P3.5

DB0-DB7

(16)

2) Demo Program (6800 Series Parallel)

// SC240128 T6963C

//*************************************************************** //* Support telephone: 0755-81452160 (SHENZHEN SinoCrystal) * //* Create by :刘俊(liujun) [email protected] * //*************************************************************** //连线表: CPU=W78E54B CPUClock=12Mhz * // LCM --- CPU * // WR --- WR * // RD --- RD * // CS --- P2.7 * // A0(RS)--- P2.0 * // DB0~7 --- P0.0~7 * // RESET --- P1.0 * // 注:本程序 BUS 总线模式程序和 IO 模式程序的硬件连线方式一致 * // 但 IO 模式的时候需要在 P0 口接 10K 上拉电阻 * //*************************************************************** #include <reg52.h> #include <intrins.h>

#include <UserDef.h> //自己些的一个头文件,主要是 Uchar 和二进制 #define Graphic 1

#define TXT 0

#define LcmXPixel 240 //横向宽度 #define LcmYPixel 128 //纵向高度

//#define BUS_MODE //总线模式驱动液晶 #define IO_MODE //IO 口模式驱动液晶 #ifdef BUS_MODE

char xdata LcmCmdPort _at_ 0x0100; //CS 低有效 RS 高--命令 char xdata LcmDatPort _at_ 0x0000; //CS 低有效 RS 低--数据 #endif #ifdef IO_MODE sbit CSP = P2^7; sbit RSP = P2^0; sbit WRP = P3^6; sbit RDP = P3^7; #define LcmDataBus P0 #endif sbit RES = P3^5; //复位信号 sbit Key = P1^1; //测试架按键 sbit FS = P3^3; //字体选择,一般在硬件接口直接接电源或地 sbit BL = P1^0; //背光开关 Uchar code str0[]; Uchar code bmp1[];

Uchar code ASCII_Lib[16*96];

//*************************************************************** //液晶驱动底层程序开始 //*************************************************************** //指令&数据读写状态 void CheckRWCD(void) { Uchar temp; #ifdef BUS_MODE while((LcmCmdPort & 0x03) != 0x03); //低电平忙 #endif #ifdef IO_MODE CSP = 0; WRP = 1; RSP = 1; LcmDataBus = 0xff; do { RDP = 0; _nop_();

(17)

temp = LcmDataBus; RDP = 1; _nop_(); } while((temp & 0x03) != 0x03); CSP = 1; #endif } //数据自动写状态 void CheckAutoWrite(void) { Uchar temp; #ifdef BUS_MODE while((LcmCmdPort & 0x08) == 0); //低电平忙 #endif #ifdef IO_MODE CSP = 0; WRP = 1; RSP = 1; LcmDataBus = 0xff; do { RDP = 0; _nop_(); temp = LcmDataBus; RDP = 1; _nop_(); } while((temp & 0x08) ==0 ); CSP = 1; #endif } //屏读/屏考贝出错状态 void CheckScreen(void) { Uchar temp; #ifdef BUS_MODE while(LcmCmdPort & 0x40); //1 出错,0 正确 #endif #ifdef IO_MODE CSP = 0; WRP = 1; RSP = 1; LcmDataBus = 0xff; do { RDP = 0; _nop_(); temp = LcmDataBus; RDP = 1; _nop_(); } while(temp & 0x40); CSP = 1; #endif } //一个数据子写入函数

void LcmWriteData(Uchar uData) { #ifdef BUS_MODE LcmDatPort = uData; #endif #ifdef IO_MODE CSP = 0; RDP = 1; RSP = 0; WRP = 0; _nop_();

(18)

LcmDataBus = uData; _nop_(); WRP = 1; CSP = 1; //LcmDataBus = 0xff; #endif } //一个数据读出函数 Uchar LcmReadData( void ) { Uchar uData; #ifdef BUS_MODE uData = LcmDatPort; #endif #ifdef IO_MODE CSP = 0; WRP = 1; RSP = 0; LcmDataBus = 0xff; RDP = 0; _nop_(); uData = LcmDataBus; _nop_(); RDP = 1; CSP = 1; #endif return uData; } //无参数指令写入函数

void LcmWriteCommand(Uchar Command) { CheckRWCD(); //检测指令读写状态 #ifdef BUS_MODE LcmCmdPort = Command; #endif #ifdef IO_MODE CSP = 0; RDP = 1; RSP = 1; WRP = 0; _nop_(); LcmDataBus = Command; _nop_(); WRP = 1; CSP = 1; //LcmDataBus = 0xff; #endif } //单参数指令写入函数

void LcmWriteCommandWith1Par(Uchar Parameter,Uchar Command) {

LcmWriteData(Parameter); LcmWriteCommand(Command); }

//双参数指令写入函数

void LcmWriteCommandWith2Par(Uchar Parameter1,Uchar Parameter2,Uchar Command) { LcmWriteData(Parameter1); LcmWriteData(Parameter2); LcmWriteCommand(Command); } //LCM 初始化函数 void LcmInit( void ) {

(19)

LcmWriteCommandWith2Par(LcmXPixel/8,0x00,0x41); //设置文本显示区宽度 LcmWriteCommandWith2Par(0x00,0x08,0x42); //设置图形显示区首地址 0x0800 LcmWriteCommandWith2Par(LcmXPixel/8,0x00,0x43); //设置图形显示区宽度 LcmWriteCommand(0xA7); //设置光标形状 8x8 方块 LcmWriteCommand(0x81); //显示方式设置文本 xor 图形(异或) LcmWriteCommand(0x9C); //显示开关设置文本开,图形开,光标闪烁关 } //函数功能: 延时函数 //入口参数: 需要延时的毫秒数(MS) //出口参数: 无

void DelayMS(unsigned int MS)

{ //For 40M STC89C516 : usn=9 us=182 //For 22.1184 STC11F60 : usn=45 us=182 unsigned char us,usn,i;

while(MS!=0) { usn = 45; while(usn!=0) { us=182; while (us!=0){us--;}; usn--; } for(i=0;i<3;i++); MS--; } } //函数功能: 特殊按键延时函数 //入口参数: 需要延时的?.?秒(Second.MS100) //出口参数: 无

void DelayKey(unsigned int Second , unsigned int MS100) { //输入精确到 0.01S,是用, unsigned int i; for(i=0;i<Second*100+MS100;i++) { if(Key==0) { DelayMS(20); while(Key==0) {DelayMS(20);} break; } else DelayMS(10); } } //清显示存储器函数

void LcmClear( Uchar FillByte ) {

Uint i = 32768; //此处仅清 8K RAM,如果您 32K RAM 都使用,请修改 i=32768(后面也要改) if(FillByte) //注意如果填充 ff 时,如果 RAM 仅使用了 8K,那么 8192 次会写入到文本区 { //会形成乱码.(24064 出厂时候默认将 R7 断开,即默认使用 8KRAM) i -= 2*1024;//所以如果填入 ff 时候要扣除 2K 的文本区 LcmWriteCommandWith2Par(0x00,0x08,0x24); //填充 0xff 时候要在图形区 } else LcmWriteCommandWith2Par(0x00,0x00,0x24); LcmWriteCommand(0xB0); //进入自动写 while(i--) { CheckAutoWrite(); LcmWriteData( FillByte ); } LcmWriteCommand(0xB2); //退出自动写 } //设定显示地址函数

void LocateXY(Uchar x,Uchar y,Uchar mode) {

Uint temp;

temp= LcmXPixel/8*y + x;

if(mode) //mode=1 为 Graphic

(20)

temp+=0x0800; }

LcmWriteCommandWith2Par(temp&0xff,temp/256,0x24); }

//显示一个 ASCII 码函数

void PutChar(Uchar x,Uchar y,Uchar CharByte) { LocateXY(x,y,TXT); LcmWriteCommandWith1Par(CharByte-0x20,0xC4); //内部带的英文字库是从 0x00 开始,也就是说空格 0x20 的字库值是 0x00,所以-0x20 } //显示一个字符串函数

void PutString(Uchar x,Uchar y,Uchar *str) { while(*str != 0) { if(x> (LcmXPixel/8-1)) //自动换行 { x=0; y++; } PutChar(x,y,*str); ++x; ++str; } } //函数功能: 在屏幕(x,y)处显示一个数据,最大 4294967295 //入口参数: 坐标(x,y),要显示的数值 Number //出口参数: 无

void PutNumber(Uchar x,Uchar y,unsigned long Number) { Uchar a[10]; Uchar i; a[0]=(Uchar)(Number/1000000000); a[1]=(Uchar)((Number%1000000000)/100000000); a[2]=(Uchar)((Number%100000000 )/10000000 ); a[3]=(Uchar)((Number%10000000 )/1000000 ); a[4]=(Uchar)((Number%1000000 )/100000 ); a[5]=(Uchar)((Number%100000 )/10000 ); a[6]=(Uchar)((Number%10000 )/1000 ); a[7]=(Uchar)((Number%1000 )/100 ); a[8]=(Uchar)((Number%100 )/10 ); a[9]=(Uchar)(Number%10); for(i=0;i<10;i++) { LocateXY(x+i,y,TXT); LcmWriteCommandWith1Par(a[i]+0x30-0x20,0xC4); } } //图形模式下显示一个 ASCII 码函数

void PutCharInGraphic(Uchar x,Uchar y,Uchar charbyte) { Uchar i; for(i=0;i<16;i++) { LocateXY(x,y+i,Graphic); LcmWriteCommandWith1Par( ASCII_Lib[(charbyte-0x20)*16+i] ,0xC4); } } //显示一副图片函数 void PutBmp(Uchar *puts) { Uchar i,j; Uint X=0; LocateXY(0,0,Graphic); LcmWriteCommand(0xB0); //进入自动写 for(i=0;i<LcmYPixel;i++) {

(21)

for(j=0;j<LcmXPixel/8;j++) { CheckAutoWrite(); LcmWriteData(puts[X]); X++; } } LcmWriteCommand(0xB2); //退出自动写 } //反显一副图片函数

void ReverseOneBmp( void )

{ //利用数据一次读写操作 Uchar i,j,X; //只能对一段 RAM 取反 LocateXY(0,0,Graphic); for(i=0;i<LcmYPixel;i++) { for(j=0;j<LcmXPixel/8;j++) { LcmWriteCommand(0xC5); //读数据,地址不变 CheckRWCD(); X = LcmReadData(); X = ~X; LcmWriteCommandWith1Par(X,0xC0); } } } //屏读功能演示

void ScreenReadDemo( void )

{ //利用屏读 //能对当前屏幕反显,包括合成内容(本函数仅读文本到图形) //但是写入后的内容都在图形区 //可以将文本区内容读出以图形方式写到图形区 Uchar i,j,X; //使用屏读屏考时候必须设置宽度为 40(硬件已决定) //所以如确定要用到屏读屏考的话最后初始化时就设 40 LcmWriteCommandWith2Par(0x28,0x00,0x41); //设置文本显示区宽度=40 LcmWriteCommandWith2Par(0x28,0x00,0x43); //设置图形显示区宽度=40 PutString(0,0,str0); //0,0 不会受到宽度改变的影响 for(i=0;i<8;i++) //屏读较慢,就以一行文本做演示 { LcmWriteCommandWith2Par((0x28*i+0x800)&0xff,(0x28*i+0x800)/256,0x24); for(j=0;j<LcmXPixel/8;j++) { LcmWriteCommand(0xE0); CheckScreen(); CheckRWCD(); X = LcmReadData(); X = ~X; LcmWriteCommandWith1Par(X,0xC0); } } //屏读需要一点时间,运行速度比较慢,运行过程中由于文本图形互补的关系,屏幕全黑 LcmWriteCommand(0x98); //关闭文本区看显示效果,会在图形显示区显示一样的字符串 DelayKey(1,0); LcmWriteCommand(0x9C); //恢复文本区显示 LcmWriteCommandWith2Par(LcmXPixel/8,0x00,0x41); //宽度改回原值 LcmWriteCommandWith2Par(LcmXPixel/8,0x00,0x43); LcmClear(0); //清屏 } //显示点阵子函数

void PutDots(Uchar DotByte,Uchar n) { Uchar i,j; LocateXY(0,0,Graphic); LcmWriteCommand(0xB0); //进入自动写 for(i=0;i<LcmYPixel/n;i++) { for(j=0;j<LcmXPixel/8*n;j++) { CheckAutoWrite(); LcmWriteData(DotByte);

(22)

} DotByte=~DotByte; } LcmWriteCommand(0xB2); //退出自动写 } //主函数 void main(void) { Uchar i,j,k;

unsigned long LoopTimes=0; //跑数字的循环次数 BL = 0; FS = 0; RES = 0; DelayMS(100); RES = 1; DelayMS(20); LcmInit(); LcmClear(0); while(1) { PutBmp(bmp1); //显示一副图片 DelayKey(3600,0); ReverseOneBmp(); //反显当前图片 DelayKey(1,0); LcmClear(0); //清屏,此处不清屏且同时打开文本和图形可观察文本 xor 图形的显示效果 LcmWriteCommand(0x94); //仅开文本,关图形,这种情况下有可能英文字库出现错误 for(i=0;i<(LcmYPixel/8);i++) //显示一屏字符串 PutString(0,i,str0); DelayKey(1,0); LcmWriteCommand(0x9C); //开文本图形 DelayKey(1,0); LcmClear(0); LcmClear(0xff); //全黑检测 DelayKey(1,0); // ScreenReadDemo(); //屏读演示,函数内包含了延时 PutDots(0x55,1); DelayKey(1,0); PutDots(0xaa,1); DelayKey(1,0); PutDots(0x33,2); DelayKey(1,0); PutDots(0xcc,2); DelayKey(1,0); PutDots(0xF0,4); DelayKey(1,0); PutDots(0x0F,4); DelayKey(1,0); LcmClear(0); //清屏 LcmWriteCommand(0x9C); //显示开关设置文本开,图形开,光标闪烁关 while(1) { for(k=0x30;k<0x7A;k++) { for(i=0;i<(LcmYPixel/8/2);i=i+2) //文本模式 for(j=0;j<(LcmXPixel/8);j=j+4) PutChar(j,i,k); for(i=LcmYPixel/2;i<LcmYPixel;i=i+24) //图形模式 for(j=0;j<(LcmXPixel/8);j=j+4) PutCharInGraphic(j,i,k); } LoopTimes++; PutNumber(0,(LcmYPixel/8-3),LoopTimes); DelayKey(0,1); } } }

(23)

//代码区

Uchar code str0[]="ShenZhen SinoCrystal Tech Co.,"; //减去 0x20 即可 Uchar code bmp1[]={ //********************************************************// //***** 转换的文件：E:\!Program 程序\!bmp\240128.bmp //***** 源图形宽度 * 高度：240 * 128 //***** 调整后宽度 * 高度：240 * 128 //***** 字模格式：横向取模,冗余模式,字节正序,正色取模, //***** 点阵转换时间：2012/07/ 5 15:34:5 //***** 位图点阵占用 3840 字节 //********************************************************// 0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF, 0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x80,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x80,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x07,0xFF, 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x0F,0xFF,0xFF,0xC0, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x0F,0xFF,0xFF,0xE0,0x00,0xF0, 0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x0F,0xFF,0xFF,0xFC,0x01,0xFC,0x00,0x00, 0x03,0xF8,0x00,0x1E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x00,0x00,0x00,0xC0, 0x00,0x01,0x80,0x00,0x00,0x00,0x0F,0x9F,0xFF,0xFE,0x01,0x8F,0x0F,0xFE,0x0F,0x18, 0x00,0x7F,0xE0,0x00,0x00,0x00,0x38,0x00,0x00,0x19,0x80,0x00,0x00,0xE0,0x00,0x01, 0x80,0x00,0x00,0x00,0x0F,0x1F,0xFC,0x7F,0x01,0x83,0x7F,0xFF,0xDC,0x18,0x01,0xFF, 0xF0,0x00,0x00,0x00,0x7C,0x00,0x00,0x30,0xC0,0x00,0x00,0xE1,0xE0,0x01,0x80,0x00, 0x00,0x00,0x1F,0x00,0x08,0x3F,0x01,0x81,0xFF,0xFF,0xF8,0x18,0x03,0x07,0x18,0x00, 0x00,0x00,0xCE,0x00,0x00,0x64,0xC0,0x00,0x00,0xE1,0xFC,0x01,0x80,0x00,0x00,0x00, 0x7F,0x00,0x00,0x3F,0x01,0x81,0xFF,0xFF,0xF8,0x18,0x0C,0x00,0x8C,0x00,0x00,0x01, 0x87,0x00,0x00,0xCE,0x60,0x00,0x00,0xE3,0xFE,0x01,0x80,0x00,0x00,0x00,0x7F,0x86, 0x30,0x7F,0x01,0x83,0xFF,0xFF,0xFC,0x18,0x1F,0xFE,0x4C,0x00,0x00,0x03,0x33,0x80, 0x01,0x9E,0x60,0x00,0x00,0xE3,0xFF,0x01,0x80,0x00,0x00,0x00,0xFF,0x86,0x30,0xFF, 0x80,0xC7,0xFF,0xFF,0xFE,0x18,0x1E,0x57,0x26,0x00,0x00,0x06,0x39,0xC0,0x01,0x9F, 0x71,0xC0,0x00,0xE3,0x87,0x01,0x80,0x00,0x00,0x00,0xFF,0x80,0x01,0xFF,0xC0,0xCF, 0xFF,0xFF,0xFE,0x30,0x24,0xA4,0xC2,0x00,0x00,0x04,0x78,0xE0,0x03,0x3F,0x37,0xF0, 0x00,0xE3,0x87,0x01,0x80,0x00,0x00,0x07,0xFF,0x80,0x01,0xFF,0xC0,0x6F,0xFF,0xFF, 0xFF,0x30,0x49,0x24,0x62,0x00,0x00,0x04,0xFC,0xFF,0xFF,0x3F,0x3C,0x38,0x00,0xE3, 0x87,0x01,0x80,0x00,0x00,0x18,0xFF,0x80,0x01,0xFF,0xC0,0x7F,0xFF,0xFF,0xFF,0xE0, 0x49,0x24,0x23,0x00,0x00,0x0C,0xFC,0x7F,0xFE,0x3F,0x10,0x1C,0x00,0xE3,0x87,0x01, 0x80,0x00,0x00,0x60,0x7F,0x80,0x01,0xFF,0xC0,0x3F,0xFF,0xFF,0xFF,0xE0,0x49,0x24, 0x13,0x00,0x00,0x08,0xFC,0x3F,0xFC,0x3F,0x10,0x0C,0x00,0xF3,0x87,0x01,0x80,0x00, 0x00,0x80,0x7F,0x00,0x00,0xFF,0x80,0x3F,0xFF,0xFF,0xFF,0xC0,0x49,0xB6,0x93,0x00, 0x00,0x08,0xFC,0x00,0x00,0x00,0x1F,0x84,0x00,0xFF,0x87,0x01,0x80,0x00,0x01,0x00, 0xFE,0x01,0xC0,0x7F,0x00,0x7F,0xFF,0xFF,0xFF,0xC0,0x6B,0xFF,0xD9,0x00,0x00,0x10, 0x00,0x20,0x02,0x00,0x1E,0xB6,0x00,0x7F,0x87,0x01,0x80,0x00,0x01,0x00,0xFC,0x02, 0x60,0x3F,0x80,0x7F,0xFF,0xFF,0xFF,0xE0,0x1F,0xE7,0xF9,0x00,0x00,0x18,0x00,0x90, 0x04,0x80,0x1A,0xA6,0x00,0x1F,0x87,0x01,0x80,0x00,0x01,0x01,0xFC,0x03,0xE0,0x3F, 0xC0,0x7F,0xFF,0xFF,0xFF,0xE0,0x07,0xE7,0xF9,0x00,0x00,0x18,0x1F,0x40,0x01,0x7C, 0x1A,0xA4,0x00,0x00,0x07,0x01,0x80,0x00,0x01,0x01,0xFC,0x00,0x00,0x1F,0xC0,0x7E, 0x07,0xFE,0x0F,0xE0,0x06,0xE3,0x7B,0x00,0x00,0x30,0x00,0x80,0x00,0x80,0x1A,0x84, 0x00,0x00,0x07,0x01,0x80,0x00,0x02,0x01,0xFC,0x00,0x00,0x1F,0xC0,0x7C,0x03,0xFC, 0x07,0xE0,0x07,0x45,0x3B,0x00,0x00,0x30,0x0F,0x00,0x00,0x78,0x08,0x0C,0x00,0xFE, 0x00,0x01,0x80,0x00,0x02,0x01,0xFC,0x00,0x00,0x1F,0xC0,0x7C,0x13,0xFC,0x03,0xE0, 0x06,0xC3,0x3B,0x00,0x00,0x30,0x10,0x80,0x00,0x84,0x0C,0x0C,0x00,0xFF,0xE0,0x01, 0x80,0x00,0x02,0x00,0xFC,0x00,0x00,0x1F,0xC0,0x7C,0x3B,0xF9,0x83,0xE0,0x06,0x00, 0x7B,0x00,0x00,0x70,0x26,0x40,0x01,0x32,0x0C,0x0C,0x00,0xFF,0xFC,0x01,0x80,0x00, 0x02,0x00,0x7E,0x00,0x00,0x3F,0x81,0xFC,0x3B,0xFB,0xC3,0xE0,0x03,0x28,0xFB,0x00, 0x00,0x60,0x2F,0x40,0x01,0x7A,0x04,0x04,0x00,0xE7,0xFE,0x01,0x80,0x3E,0x04,0x00, 0x7F,0x00,0x00,0x7F,0x80,0x7C,0x13,0xFD,0x83,0xFF,0x01,0x91,0xFF,0x00,0x00,0x60, 0x26,0x40,0x01,0x32,0x06,0x04,0x00,0xE0,0x3E,0x01,0x80,0x3F,0x00,0x00,0x7F,0x80, 0x00,0xFF,0x82,0x3E,0x07,0xFC,0x07,0xC0,0x01,0xC7,0xFF,0x00,0x00,0x60,0x10,0x80, 0x00,0x84,0x06,0x06,0x00,0xE0,0x07,0x01,0x80,0x7F,0x0F,0x00,0x3F,0xC0,0x01,0xFF, 0x80,0x3F,0x0F,0x9E,0x0F,0xC0,0x01,0x3E,0x7F,0x00,0x00,0x60,0x0F,0x00,0x00,0x78, 0x06,0x06,0x00,0xE0,0x07,0x01,0x80,0x7F,0x09,0x01,0x1F,0xE0,0x03,0xFF,0x00,0x1F, 0xFF,0x0F,0xFF,0x80,0x02,0x24,0x3F,0x00,0x00,0x60,0x00,0x00,0x00,0x00,0x06,0x06, 0x00,0xE0,0x07,0x01,0x80,0x7F,0x19,0x01,0x43,0xFF,0x9F,0xFF,0x00,0x3F,0xFF,0xFF, 0xFF,0x80,0x04,0x18,0x1F,0x00,0x00,0x60,0x00,0x00,0x00,0x00,0x26,0x02,0x00,0xE0, 0x07,0x01,0x80,0x7F,0x31,0x02,0x47,0xFF,0xFF,0xFE,0x00,0xE7,0xFF,0xFF,0xFF,0xC0, 0x05,0x00,0x0F,0x00,0x00,0x72,0x00,0x00,0x80,0x3F,0xC6,0x07,0x00,0xE0,0x07,0x01, 0x80,0x3E,0x28,0x02,0x43,0xFF,0xFF,0xF0,0x01,0x83,0xFF,0xFF,0xFE,0x30,0x07,0x00, 0x1D,0x00,0x00,0x71,0xFF,0x81,0xF0,0x40,0x06,0x4F,0x00,0xE0,0x07,0x01,0x80,0x01,

(24)

0xF1,0x04,0x41,0xFF,0xFF,0xF0,0x00,0x00,0xFF,0xFF,0xF8,0x0C,0x05,0x00,0x68,0x00, 0x00,0x70,0x00,0x41,0xF0,0x00,0x26,0x4F,0x00,0xE0,0x07,0x01,0x80,0x00,0x01,0x04, 0x40,0xF7,0xFF,0xE0,0x02,0x00,0x3F,0xFF,0xE0,0x00,0x03,0x00,0xD0,0x00,0x00,0x31, 0x00,0x01,0xF0,0x3F,0xC4,0x0E,0x00,0x20,0x07,0x01,0x80,0x00,0x01,0x00,0x40,0x27, 0xF3,0x80,0x00,0x00,0x04,0x02,0x00,0x00,0x01,0x80,0x60,0x00,0x00,0x38,0xFF,0x80, 0xC0,0x40,0x24,0x0F,0x00,0xE0,0x07,0x01,0x80,0x00,0x01,0x04,0x40,0xA1,0xE0,0x80, 0x00,0x00,0x04,0x02,0x00,0x00,0x00,0x80,0x40,0x00,0x00,0x39,0x00,0x40,0xC0,0x07, 0xC8,0x0E,0x00,0xFE,0x07,0x01,0x80,0x00,0x01,0x00,0x00,0x20,0x10,0x80,0x00,0x00, 0x07,0xFF,0x00,0x00,0x00,0xFF,0xC0,0x00,0x00,0x1C,0xFE,0x01,0xA0,0x18,0x08,0x06, 0x00,0xFF,0x10,0x01,0x80,0x00,0x01,0x04,0x01,0xA1,0x10,0x80,0x00,0x00,0x07,0xF7, 0x00,0x00,0x00,0x7E,0x40,0x00,0x00,0x0E,0x01,0x83,0x20,0x20,0x18,0x02,0x00,0xFF, 0x9E,0x01,0x80,0x00,0x01,0x04,0x41,0xA1,0x10,0x80,0x00,0x40,0x04,0xF3,0x00,0x00, 0x00,0x5C,0x40,0x00,0x00,0x0E,0x00,0x42,0x10,0x00,0x30,0x06,0x00,0xE3,0x9E,0x01, 0x80,0x00,0x01,0x05,0x40,0x21,0x10,0x80,0x00,0x60,0x06,0xFB,0xF0,0x00,0x00,0x48, 0x40,0x00,0x00,0x07,0x00,0x0E,0x0C,0x00,0x30,0x04,0x00,0xE3,0x9F,0x01,0x80,0x00, 0x01,0x01,0x3F,0xA2,0x70,0x40,0x00,0x70,0x06,0xFB,0xF0,0x00,0x00,0x40,0x40,0x00, 0x00,0x03,0x80,0x7C,0x07,0x80,0xF0,0x0C,0x00,0xE3,0x87,0x01,0x80,0x00,0x00,0xBC, 0x0B,0x01,0x40,0x20,0x00,0x30,0x07,0x73,0xF0,0x00,0x00,0x40,0xC0,0x00,0x00,0x03, 0xC0,0xF0,0x03,0x83,0xF0,0x0C,0x00,0xE3,0x87,0x01,0x80,0x00,0x00,0x00,0x01,0x23, 0x40,0x20,0x00,0x18,0x07,0x07,0xF0,0x00,0x00,0x24,0x80,0x00,0x00,0x03,0xF0,0x00, 0x00,0x0F,0xE0,0x08,0x00,0xE3,0x87,0x01,0x80,0x00,0x00,0x00,0x00,0x11,0x34,0xC0, 0x00,0x0C,0x0F,0xCF,0xF0,0x00,0x00,0x24,0x80,0x00,0x00,0x03,0xF8,0x00,0x00,0x7F, 0xC0,0x08,0x00,0xE3,0x87,0x01,0x80,0x00,0x00,0x00,0x00,0x3F,0x0B,0x80,0x00,0x07, 0xFB,0xFF,0xE0,0x00,0x00,0x34,0x80,0x00,0x00,0x03,0xFF,0x80,0x3F,0xFF,0x80,0x10, 0x00,0xE3,0x87,0x01,0x80,0x00,0x00,0x00,0x00,0x1C,0x00,0x00,0x00,0x03,0xF1,0xF8, 0x00,0x00,0x00,0x14,0x80,0x00,0x00,0x06,0xFF,0xFF,0xFF,0xFF,0xC0,0x38,0x00,0xE3, 0xC7,0x01,0x80,0x00,0x00,0x00,0x0C,0x00,0x00,0x00,0x00,0x00,0x01,0xF8,0x00,0x00, 0x00,0x14,0x80,0x00,0x00,0x06,0x7F,0xFF,0xFF,0xFF,0xC0,0x38,0x00,0xE1,0xFF,0x01, 0x80,0x00,0x00,0x00,0x3E,0x00,0x00,0x00,0x00,0x00,0x01,0xF8,0x00,0x00,0x00,0x24, 0x80,0x00,0x00,0x04,0x3F,0xFF,0xFF,0xFF,0xC0,0x30,0x00,0x01,0xFF,0x01,0x80,0x00, 0x00,0x00,0xE3,0x00,0x00,0x00,0x00,0x00,0x01,0xFC,0x00,0x00,0x00,0x44,0x40,0x00, 0x00,0x0C,0x03,0xFF,0xFF,0xFF,0xC0,0x38,0x00,0x00,0x7E,0x01,0x80,0x00,0x00,0x7F, 0x81,0x00,0x00,0x00,0x00,0x00,0x00,0xFC,0x00,0x00,0x00,0x7C,0x20,0x00,0x00,0x0C, 0x02,0xFF,0xFE,0xF3,0x80,0x38,0x00,0x00,0x06,0x01,0x80,0x00,0x00,0xFF,0x01,0x80, 0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x00,0x00,0x03,0xE0,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x1C,0x00,0x01,0x80,0x00,0x00,0xFF,0xE3,0xE0,0x00,0x00, 0x00,0x00,0x00,0x01,0xC6,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x1E,0x00,0x01,0x80,0x00,0x00,0xFF,0xFF,0xF0,0x00,0x00,0x00,0x07, 0xE7,0xFF,0x82,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x1F,0x80,0x01,0x80,0x00,0x01,0xFF,0xFF,0xF0,0x00,0x00,0x00,0x1C,0x3F,0xFF, 0x26,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1B, 0xC0,0x01,0x80,0x00,0x01,0xFF,0xFF,0xF0,0x00,0x00,0x00,0x18,0x18,0x01,0x3C,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x19,0xE0,0x01, 0x80,0x00,0x01,0xFF,0xFF,0xF0,0x00,0x00,0x00,0x19,0x80,0x00,0x04,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x18,0xF0,0x01,0x80,0x00, 0x07,0xFF,0xFF,0xF0,0x00,0x00,0x00,0x1B,0x80,0x00,0x04,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF8,0x3C,0x01,0x80,0x00,0x1D,0xFF, 0xFF,0xF0,0x00,0x00,0x00,0x1E,0x00,0x00,0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x1E,0x01,0x80,0x7F,0xF0,0xFF,0xFF,0xF8, 0x00,0x00,0x00,0x06,0x03,0x8E,0x0C,0x00,0x0F,0xF8,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x01,0x80,0x60,0x60,0xFF,0xFF,0xEC,0x00,0x00, 0x00,0x06,0x00,0x00,0x04,0x00,0x7C,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x3F,0xFF,0x01,0x80,0xC0,0x00,0x7E,0x0F,0xE6,0xE0,0x00,0x60,0x06, 0x00,0x06,0x06,0x01,0xCE,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x19,0xFF,0x01,0x80,0xC0,0x00,0x00,0x03,0xC3,0x80,0x00,0xFE,0x06,0x03,0xCD, 0x02,0x03,0x30,0x03,0x00,0x00,0x00,0x00,0x00,0x0A,0x00,0x00,0x3E,0x00,0x00,0x18, 0x0F,0x01,0x80,0xC0,0x00,0x00,0x00,0x07,0x00,0x00,0x83,0x8C,0x06,0x30,0x83,0x06, 0xC0,0x02,0x00,0x00,0x00,0x00,0x00,0x1F,0xC0,0x01,0xF3,0x00,0x00,0x00,0x00,0x01, 0x80,0xC0,0x00,0x00,0x00,0x05,0x00,0x00,0x80,0xCC,0x04,0xB4,0x83,0x19,0x80,0x0E, 0x00,0x07,0xFF,0x70,0x00,0x18,0xE0,0x03,0x83,0x00,0x00,0x00,0x00,0x01,0x80,0x40, 0x00,0x00,0x00,0x01,0xE0,0x00,0x86,0x2C,0x04,0xF4,0x83,0x73,0x00,0x08,0x00,0x7F, 0xFF,0xF8,0x00,0x11,0x3F,0xE6,0x43,0x00,0x00,0xFC,0x00,0x01,0x80,0x40,0x00,0x00, 0x00,0x01,0xE0,0x00,0x83,0x9C,0x00,0x01,0x83,0xE4,0x00,0x08,0x00,0xFF,0xFF,0xFC, 0x00,0x10,0x8F,0xF8,0x83,0x00,0x00,0xFF,0xE0,0x01,0x80,0x60,0x00,0x00,0x00,0x01, 0x80,0x01,0x80,0xCC,0x00,0x7C,0x01,0x8C,0x00,0x08,0x01,0xFF,0xFF,0xFE,0x00,0x10, 0x9F,0xF1,0x82,0x00,0x00,0xFF,0xFC,0x01,0x80,0x70,0x00,0x00,0x00,0x01,0x80,0x01, 0x80,0x7C,0x00,0xC6,0x03,0x18,0x00,0x18,0x03,0xFF,0xFF,0xFF,0x00,0x1B,0x3F,0xF0, 0x66,0x00,0x00,0xEF,0xFE,0x01,0x80,0x30,0x00,0x00,0x00,0xCF,0xF0,0x00,0x80,0x3C, 0x01,0x02,0x03,0x30,0x00,0x30,0x07,0xFF,0xFF,0xFF,0x00,0x16,0x7F,0xE0,0x36,0x00, 0x00,0xE0,0x7E,0x01,0x80,0x30,0x00,0x00,0x01,0xDF,0xF1,0xC0,0x80,0x1C,0x01,0x5E, 0x83,0x60,0x00,0x20,0x07,0xFF,0xFF,0xFF,0x00,0x1C,0x78,0x00,0xC6,0x00,0x00,0xE0, 0x0F,0x01,0x80,0x30,0x00,0x00,0x00,0xFF,0xFF,0xF0,0x80,0x0E,0x01,0x03,0x86,0x60, 0x00,0x20,0x0F,0xFF,0xFF,0xFF,0x80,0x18,0x78,0x00,0xFC,0x00,0x00,0xE0,0x07,0x01, 0x80,0x30,0x00,0x00,0x00,0x7F,0x07,0xF0,0x80,0x0E,0x07,0xFE,0x06,0x40,0x00,0xE0,

(25)

0x0F,0xFF,0xFF,0xFF,0x80,0x18,0xC0,0xE0,0xFC,0x00,0x00,0xE0,0x07,0x01,0x80,0x30, 0x00,0x00,0x00,0x1C,0x01,0xF0,0x80,0x07,0x00,0xF8,0x0E,0x80,0x01,0x40,0x0F,0xFF, 0xFF,0xFF,0x80,0x10,0xE0,0x00,0x7C,0x00,0x00,0xE0,0x07,0x01,0x80,0x10,0x00,0x00, 0x00,0x18,0x00,0xF0,0xC0,0x07,0x00,0x48,0x0C,0x80,0x01,0x00,0x1F,0xFF,0xFF,0xFF, 0x80,0x10,0x00,0x00,0x7C,0x00,0x00,0xE0,0x07,0x01,0x80,0x10,0x00,0x00,0x00,0x18, 0x00,0x70,0x60,0x05,0x80,0x78,0x18,0x80,0x03,0x00,0x1F,0xFF,0xFF,0xFF,0x80,0x18, 0x00,0x00,0x1C,0x00,0x00,0xFE,0x07,0x01,0x80,0x18,0x00,0x00,0xE0,0x18,0x00,0x70, 0xC0,0x04,0xC0,0x00,0x3F,0xC0,0x0E,0x00,0x1F,0xFF,0xFF,0xFF,0x80,0x18,0x00,0x00, 0x1E,0x00,0x00,0x7F,0xFF,0x01,0x80,0x18,0x06,0x01,0xB0,0x11,0x00,0x60,0xC0,0x04, 0x70,0x00,0xEF,0xF8,0x08,0x00,0x1F,0xFF,0x83,0xBF,0x80,0x18,0x60,0xE0,0x06,0x00, 0x00,0x3F,0xFF,0x01,0x80,0x08,0x0E,0x01,0xA0,0x31,0x00,0x20,0x40,0x07,0xF8,0x03, 0x88,0x3F,0xBE,0x00,0x1F,0x9D,0x82,0x91,0x00,0x08,0xF0,0xB0,0x06,0x00,0x00,0x03, 0xFE,0x01,0x80,0x0C,0x06,0x00,0xC0,0x18,0x6C,0x20,0x70,0x7F,0x63,0xFA,0x30,0x05, 0xE1,0x00,0x3F,0x3D,0x80,0xD9,0x00,0x08,0x90,0x90,0x06,0x00,0x00,0x00,0x1E,0x01, 0x80,0x07,0x00,0x00,0x00,0x38,0x60,0x60,0x21,0xF0,0x30,0x00,0x60,0x00,0x61,0x00, 0x3C,0x1D,0x00,0xCD,0x00,0x38,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,0x01,0x80,0x07, 0x00,0x00,0x00,0x7C,0x70,0x60,0x23,0x80,0x18,0x10,0x00,0x00,0x67,0x00,0x39,0x80, 0x30,0x46,0x00,0x5E,0x1C,0x00,0x84,0x00,0x00,0x00,0x00,0x01,0x80,0x0F,0x00,0x00, 0x01,0xFE,0x00,0xC0,0x36,0x00,0x00,0x10,0x00,0x00,0x66,0x00,0x31,0x02,0x1F,0x02, 0x00,0x5E,0x1C,0x00,0x8E,0x00,0x00,0x00,0x00,0x01,0x80,0x19,0xC0,0x00,0x0F,0xFF, 0x81,0x80,0xFC,0x00,0x00,0x00,0x00,0x00,0x6C,0x00,0x22,0x0C,0x00,0x82,0x00,0x7E, 0x08,0x00,0xD8,0x00,0x00,0x00,0x00,0x01,0x80,0x01,0xC0,0x00,0x7F,0xFD,0xFF,0x01, 0x8C,0x00,0x00,0x00,0x00,0x00,0xF8,0x00,0x02,0x1B,0x87,0x42,0x06,0xC9,0x98,0x30, 0x3E,0x00,0x00,0xF0,0x07,0x01,0x80,0x03,0x78,0x03,0xC0,0x7F,0xFC,0x00,0xEC,0x00, 0x00,0x00,0x00,0x4B,0xC0,0x00,0x01,0x77,0xCF,0x4F,0x04,0x8C,0xD9,0xE0,0x61,0x80, 0x00,0xFF,0x87,0x01,0x80,0x02,0x3F,0xFF,0x80,0x3F,0xCC,0x00,0x64,0x1C,0x00,0x00, 0x00,0x3F,0x00,0x00,0x01,0xF7,0xCF,0x7F,0x0C,0xC7,0x3F,0x81,0xF3,0x60,0x00,0xFF, 0xFF,0x01,0x80,0x00,0x27,0xFF,0x80,0x3D,0xC6,0x00,0x27,0xFC,0x00,0x00,0x00,0x98, 0x00,0x00,0x03,0xFB,0x86,0x7F,0x0A,0x79,0xC0,0x1F,0x97,0x20,0x00,0x1F,0xFF,0x01, 0x80,0x00,0x60,0x3F,0xC0,0x3F,0x86,0x00,0x3F,0x8D,0x80,0x00,0x02,0x80,0x00,0x00, 0x06,0xFC,0x00,0xDF,0x0A,0x3E,0x7F,0xFD,0xF7,0xA0,0x00,0x01,0xFF,0x01,0x80,0x00, 0x40,0x3F,0xC0,0x3F,0x87,0x00,0x01,0x9E,0xA9,0x80,0xEA,0xA0,0x00,0x00,0x02,0x30, 0xFF,0x1F,0x0E,0x02,0xB1,0xCD,0xC7,0xA0,0x00,0xE0,0x0F,0x01,0x80,0x00,0x00,0x7F, 0xC0,0x7F,0x87,0x00,0x00,0xDE,0xAA,0xB7,0xAA,0xB0,0x00,0x00,0x01,0xE0,0x7C,0x0E, 0x03,0x03,0x99,0xF0,0x4F,0x60,0x00,0xFE,0x00,0x01,0x80,0x00,0x00,0x7F,0xC0,0xFF, 0x87,0x80,0x00,0x7E,0xAA,0xB5,0xAA,0xB0,0x00,0x00,0x01,0xE0,0x38,0x1F,0x01,0x01, 0x9B,0x60,0x4E,0x60,0x00,0xFF,0x10,0x01,0x80,0x00,0x0F,0xFF,0xC3,0xFF,0xC7,0xC0, 0x00,0x1E,0xA2,0xB5,0xFA,0xB0,0x00,0x00,0x02,0x00,0x00,0x01,0x80,0x03,0x06,0x60, 0xDC,0xC0,0x00,0xFF,0x9E,0x01,0x80,0x00,0x3F,0xFF,0xFF,0xFF,0xFF,0xC0,0x00,0x18, 0xAA,0xD5,0xDC,0x30,0x00,0x00,0x04,0x00,0x00,0x00,0x80,0x0F,0x45,0xB3,0xFC,0x80, 0x00,0xE3,0x9E,0x01,0x80,0x00,0x61,0xFF,0xFF,0xFF,0xFF,0x40,0x00,0x18,0xBE,0xFF, 0xD0,0x30,0x00,0x00,0x04,0x00,0x00,0x01,0x80,0x39,0x0C,0xDE,0xC1,0xC0,0x00,0xE3, 0x9F,0x01,0x80,0x00,0x61,0xFF,0xFF,0x9F,0xFF,0xC0,0x00,0x18,0x12,0xE7,0x00,0x30, 0x00,0x00,0x04,0xC0,0x00,0x0D,0x80,0x7F,0x1B,0x2C,0x73,0x78,0x00,0xE3,0x87,0x01, 0x80,0x00,0x63,0xFF,0xFF,0x86,0x07,0x00,0x00,0x08,0x00,0x00,0x00,0x70,0x00,0x00, 0x03,0xC0,0x00,0x07,0x00,0xF1,0x34,0xC8,0x7E,0x1C,0x00,0xE3,0x87,0x01,0x80,0x00, 0x33,0xFF,0xFF,0x86,0x06,0x00,0x00,0x08,0x00,0x00,0x00,0x60,0x00,0x00,0x01,0xA0, 0x00,0x06,0x01,0xE0,0x33,0x1A,0x04,0x30,0x00,0xE3,0x87,0x01,0x80,0x00,0x1F,0xFF, 0xFF,0x86,0x06,0x00,0x00,0x08,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0xE0,0x00,0x04, 0x01,0x81,0x2D,0xB0,0x02,0x20,0x00,0xE3,0x87,0x01,0x80,0x00,0x0F,0xFF,0xFF,0xC6, 0x04,0x00,0x00,0x0E,0x30,0x00,0x38,0xC0,0x00,0x00,0x00,0xC0,0x00,0x06,0x02,0xC0, 0x26,0x60,0x06,0x60,0x00,0xE3,0x87,0x01,0x80,0x00,0x07,0xFF,0xFF,0xC6,0x0C,0x00, 0x00,0x0F,0x1E,0xCD,0xE3,0xC0,0x00,0x00,0x00,0xC0,0x00,0x06,0x06,0xC7,0xF0,0xDF, 0x02,0xC0,0x00,0xE3,0xC7,0x01,0x80,0x00,0x07,0xFF,0xFF,0xFE,0x08,0x00,0x00,0x1F, 0xE0,0xCC,0x0F,0xC0,0x00,0x00,0x00,0xC0,0x00,0x04,0x06,0x6F,0x7F,0xFF,0x87,0x80, 0x00,0xE1,0xFF,0x01,0x80,0x00,0x06,0x00,0x00,0x3F,0x38,0x00,0x00,0x1F,0xF8,0x00, 0xFF,0xC0,0x00,0x00,0x00,0xC0,0x00,0x04,0x04,0x38,0x86,0x00,0xF9,0x00,0x00,0x01, 0xFF,0x01,0x80,0x00,0x06,0x00,0x00,0x03,0xF0,0x00,0x00,0x1F,0xFF,0xFF,0xFF,0xC0, 0x00,0x00,0x00,0x60,0x00,0x0C,0x0C,0x00,0x80,0x20,0x53,0x00,0x00,0x00,0x7E,0x01, 0x80,0x00,0x06,0x00,0x00,0x03,0x00,0x00,0x00,0x1F,0xFF,0xFF,0xFF,0xE0,0x00,0x00, 0x00,0x60,0x00,0x08,0x0C,0x00,0x33,0x20,0x06,0x00,0x00,0x00,0x06,0x01,0x80,0x00, 0x06,0x00,0x00,0x03,0x00,0x00,0x00,0x1F,0xFF,0xFF,0xFF,0xE0,0x00,0x00,0x00,0x36, 0x01,0x98,0x3F,0x80,0x02,0x00,0x0C,0x00,0x00,0xFC,0x00,0x01,0x80,0x00,0x02,0x00, 0x00,0x03,0x00,0x00,0x00,0x1F,0xFF,0xCF,0xFF,0xE0,0x00,0x00,0x00,0x11,0xFF,0x90, 0x11,0xF8,0x00,0x00,0x18,0x00,0x00,0xFE,0x60,0x01,0x80,0x00,0x03,0x00,0x00,0x06, 0x00,0x00,0x00,0x1F,0xFF,0x8F,0xFF,0xE0,0x00,0x00,0x00,0x11,0x00,0x20,0x00,0x1F, 0xE0,0x03,0xF0,0x00,0x00,0xFF,0xFC,0x01,0x80,0x00,0x03,0x00,0x00,0x0C,0x00,0x00, 0x00,0x0F,0xFF,0x87,0xFF,0xE0,0x00,0x00,0x00,0x0A,0x00,0x40,0x00,0x00,0xFF,0xFF, 0xF0,0x00,0x00,0xE7,0xFE,0x01,0x80,0x00,0x01,0xC0,0x00,0x38,0x00,0x00,0x00,0x0F, 0xFF,0xC7,0xFF,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x00, 0x00,0xE3,0xFE,0x01,0x80,0x00,0x00,0xFF,0xFF,0xF0,0x00,0x00,0x00,0x05,0xFF,0x03, 0x62,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE3, 0x87,0x01,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x0C,0x01,0x06,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE3,0x87,0x01,

(26)

0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE3,0x87,0x01,0x84,0x00, 0x09,0x04,0x04,0x00,0x48,0x00,0x80,0x07,0xF0,0x08,0x40,0x82,0x00,0x40,0x1D,0xF8, 0x09,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0xE3,0x87,0x01,0x82,0xFF,0x09,0x24, 0x02,0x20,0x48,0x80,0x40,0x04,0x10,0x70,0x40,0x82,0x00,0x42,0x15,0x08,0x09,0x01, 0xFF,0xC0,0x00,0x00,0x00,0x00,0x00,0xF3,0x87,0x01,0x80,0x81,0x09,0x24,0xFF,0xF0, 0x8B,0x07,0xFC,0x07,0xF0,0x12,0x40,0x82,0x0F,0xFF,0x15,0x08,0x10,0x80,0x00,0x80, 0x07,0x0E,0x08,0x38,0x00,0xFF,0xC7,0x01,0x88,0x24,0x09,0x24,0x02,0x01,0x8C,0x00, 0x08,0x04,0x10,0x11,0x43,0xDF,0xC0,0x80,0x15,0xF8,0x10,0x83,0xFE,0x80,0x08,0x91, 0x18,0x44,0x00,0x7F,0xFF,0x01,0x84,0x52,0x3F,0x24,0x3F,0xC2,0xB8,0x40,0x10,0x07, 0xF0,0xFC,0x40,0x82,0x01,0xFC,0x19,0x08,0x20,0x40,0x00,0x80,0x08,0x91,0x08,0x44, 0x00,0x3F,0xFF,0x01,0x80,0x10,0x09,0x24,0x22,0x40,0x88,0x40,0x20,0x00,0x00,0x12, 0x40,0xCF,0x83,0x04,0x15,0xF8,0x44,0x20,0xF8,0x80,0x00,0x91,0x08,0x04,0x00,0x00, 0x7E,0x01,0x82,0xFF,0x09,0x24,0x22,0x40,0x87,0xC0,0x40,0x1F,0x7C,0x39,0x41,0x88, 0x85,0xFC,0x15,0x48,0x84,0x10,0x88,0x80,0x01,0x11,0x08,0x08,0x00,0x00,0x0E,0x01, 0x84,0x10,0x09,0x24,0x22,0x40,0x10,0x00,0x80,0x11,0x44,0x54,0x72,0x88,0x89,0x04, 0x15,0x50,0x08,0x00,0x88,0x80,0x02,0x11,0x08,0x10,0x00,0x00,0x00,0x01,0x8C,0x38, 0x0F,0x24,0x22,0x43,0xFF,0xC1,0x00,0x1F,0x7C,0x97,0xC0,0x85,0x01,0xFC,0x1D,0x20, 0x09,0x00,0xF8,0x80,0x04,0x11,0x08,0x20,0x00,0x00,0x00,0x01,0x84,0x54,0x39,0x24, 0x22,0x40,0x10,0x03,0x00,0x11,0x44,0x10,0x40,0x82,0x01,0x04,0x11,0x10,0x10,0x80, 0x88,0x80,0x08,0x11,0x08,0x40,0x00,0x00,0x00,0x01,0x85,0x93,0x12,0x04,0x22,0xC0, 0x10,0x0C,0xC0,0x1F,0x7C,0x10,0x40,0x85,0x01,0x04,0x11,0x48,0x3F,0xC0,0x02,0x80, 0x0F,0x8E,0x1C,0x7C,0x00,0x00,0x00,0x01,0x84,0x10,0x04,0x04,0x02,0x00,0x10,0x00, 0x3F,0x11,0x44,0x10,0x41,0xB8,0xC1,0x0C,0x11,0x84,0x10,0x40,0x01,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x01,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF, 0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF, };

unsigned char code ASCII_Lib[16*96] = {

/*********************************************/ /*----点阵转换时间：2006/07/ 4 13:3:25----*/ /*----Fixedsys 12(8*16) 调整后: 宽度 x 高度:8x16 /*----转换字模个数:96 字库大小:1536 字节 /*********************************************/ /*---转换字符 0 ---*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*---转换字符 ! 1 ---*/ 0x00,0x00,0x00,0x18,0x3C,0x3C,0x3C,0x18,0x18,0x00,0x18,0x18,0x00,0x00,0x00,0x00, /*---转换字符 " 2 ---*/ 0x00,0x00,0x00,0x66,0x66,0x66,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*---转换字符 # 3 ---*/ 0x00,0x00,0x00,0x36,0x36,0x7F,0x36,0x36,0x36,0x7F,0x36,0x36,0x00,0x00,0x00,0x00, /*---转换字符 $ 4 ---*/ 0x00,0x18,0x18,0x3C,0x66,0x60,0x30,0x18,0x0C,0x06,0x66,0x3C,0x18,0x18,0x00,0x00, /*---转换字符 % 5 ---*/ 0x00,0x00,0x70,0xD8,0xDA,0x76,0x0C,0x18,0x30,0x6E,0x5B,0x1B,0x0E,0x00,0x00,0x00, /*---转换字符 & 6 ---*/ 0x00,0x00,0x00,0x38,0x6C,0x6C,0x38,0x60,0x6F,0x66,0x66,0x3B,0x00,0x00,0x00,0x00, /*---转换字符 ' 7 ---*/ 0x00,0x00,0x00,0x18,0x18,0x18,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*---转换字符 ( 8 ---*/ 0x00,0x00,0x00,0x0C,0x18,0x18,0x30,0x30,0x30,0x30,0x30,0x18,0x18,0x0C,0x00,0x00, /*---转换字符 ) 9 ---*/ 0x00,0x00,0x00,0x30,0x18,0x18,0x0C,0x0C,0x0C,0x0C,0x0C,0x18,0x18,0x30,0x00,0x00, /*---转换字符 * 10 ---*/ 0x00,0x00,0x00,0x00,0x00,0x36,0x1C,0x7F,0x1C,0x36,0x00,0x00,0x00,0x00,0x00,0x00, /*---转换字符 + 11 ---*/ 0x00,0x00,0x00,0x00,0x00,0x18,0x18,0x7E,0x18,0x18,0x00,0x00,0x00,0x00,0x00,0x00, /*---转换字符 , 12 ---*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1C,0x1C,0x0C,0x18,0x00,0x00, /*---转换字符 - 13 ---*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*---转换字符 . 14 ---*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1C,0x1C,0x00,0x00,0x00,0x00, /*---转换字符 / 15 ---*/ 0x00,0x00,0x00,0x06,0x06,0x0C,0x0C,0x18,0x18,0x30,0x30,0x60,0x60,0x00,0x00,0x00, /*---转换字符 0 16 ---*/ 0x00,0x00,0x00,0x1E,0x33,0x37,0x37,0x33,0x3B,0x3B,0x33,0x1E,0x00,0x00,0x00,0x00, /*---转换字符 1 17 ---*/

(27)

0x00,0x00,0x00,0x0C,0x1C,0x7C,0x0C,0x0C,0x0C,0x0C,0x0C,0x0C,0x00,0x00,0x00,0x00, /*---转换字符 2 18 ---*/ 0x00,0x00,0x00,0x3C,0x66,0x66,0x06,0x0C,0x18,0x30,0x60,0x7E,0x00,0x00,0x00,0x00, /*---转换字符 3 19 ---*/ 0x00,0x00,0x00,0x3C,0x66,0x66,0x06,0x1C,0x06,0x66,0x66,0x3C,0x00,0x00,0x00,0x00, /*---转换字符 4 20 ---*/ 0x00,0x00,0x00,0x30,0x30,0x36,0x36,0x36,0x66,0x7F,0x06,0x06,0x00,0x00,0x00,0x00, /*---转换字符 5 21 ---*/ 0x00,0x00,0x00,0x7E,0x60,0x60,0x60,0x7C,0x06,0x06,0x0C,0x78,0x00,0x00,0x00,0x00, /*---转换字符 6 22 ---*/ 0x00,0x00,0x00,0x1C,0x18,0x30,0x7C,0x66,0x66,0x66,0x66,0x3C,0x00,0x00,0x00,0x00, /*---转换字符 7 23 ---*/ 0x00,0x00,0x00,0x7E,0x06,0x0C,0x0C,0x18,0x18,0x30,0x30,0x30,0x00,0x00,0x00,0x00, /*---转换字符 8 24 ---*/ 0x00,0x00,0x00,0x3C,0x66,0x66,0x76,0x3C,0x6E,0x66,0x66,0x3C,0x00,0x00,0x00,0x00, /*---转换字符 9 25 ---*/ 0x00,0x00,0x00,0x3C,0x66,0x66,0x66,0x66,0x3E,0x0C,0x18,0x38,0x00,0x00,0x00,0x00, /*---转换字符 : 26 ---*/ 0x00,0x00,0x00,0x00,0x00,0x1C,0x1C,0x00,0x00,0x00,0x1C,0x1C,0x00,0x00,0x00,0x00, /*---转换字符 ; 27 ---*/ 0x00,0x00,0x00,0x00,0x00,0x1C,0x1C,0x00,0x00,0x00,0x1C,0x1C,0x0C,0x18,0x00,0x00, /*---转换字符 < 28 ---*/ 0x00,0x00,0x00,0x06,0x0C,0x18,0x30,0x60,0x30,0x18,0x0C,0x06,0x00,0x00,0x00,0x00, /*---转换字符 = 29 ---*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x00,0x7E,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*---转换字符 > 30 ---*/ 0x00,0x00,0x00,0x60,0x30,0x18,0x0C,0x06,0x0C,0x18,0x30,0x60,0x00,0x00,0x00,0x00, /*---转换字符 ? 31 ---*/ 0x00,0x00,0x00,0x3C,0x66,0x66,0x0C,0x18,0x18,0x00,0x18,0x18,0x00,0x00,0x00,0x00, /*---转换字符 @ 32 ---*/ 0x00,0x00,0x00,0x7E,0xC3,0xC3,0xCF,0xDB,0xDB,0xCF,0xC0,0x7F,0x00,0x00,0x00,0x00, /*---转换字符 A 33 ---*/ 0x00,0x00,0x00,0x18,0x3C,0x66,0x66,0x66,0x7E,0x66,0x66,0x66,0x00,0x00,0x00,0x00, /*---转换字符 B 34 ---*/ 0x00,0x00,0x00,0x7C,0x66,0x66,0x66,0x7C,0x66,0x66,0x66,0x7C,0x00,0x00,0x00,0x00, /*---转换字符 C 35 ---*/ 0x00,0x00,0x00,0x3C,0x66,0x66,0x60,0x60,0x60,0x66,0x66,0x3C,0x00,0x00,0x00,0x00, /*---转换字符 D 36 ---*/ 0x00,0x00,0x00,0x78,0x6C,0x66,0x66,0x66,0x66,0x66,0x6C,0x78,0x00,0x00,0x00,0x00, /*---转换字符 E 37 ---*/ 0x00,0x00,0x00,0x7E,0x60,0x60,0x60,0x7C,0x60,0x60,0x60,0x7E,0x00,0x00,0x00,0x00, /*---转换字符 F 38 ---*/ 0x00,0x00,0x00,0x7E,0x60,0x60,0x60,0x7C,0x60,0x60,0x60,0x60,0x00,0x00,0x00,0x00, /*---转换字符 G 39 ---*/ 0x00,0x00,0x00,0x3C,0x66,0x66,0x60,0x60,0x6E,0x66,0x66,0x3E,0x00,0x00,0x00,0x00, /*---转换字符 H 40 ---*/ 0x00,0x00,0x00,0x66,0x66,0x66,0x66,0x7E,0x66,0x66,0x66,0x66,0x00,0x00,0x00,0x00, /*---转换字符 I 41 ---*/ 0x00,0x00,0x00,0x3C,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x3C,0x00,0x00,0x00,0x00, /*---转换字符 J 42 ---*/ 0x00,0x00,0x00,0x06,0x06,0x06,0x06,0x06,0x06,0x66,0x66,0x3C,0x00,0x00,0x00,0x00, /*---转换字符 K 43 ---*/ 0x00,0x00,0x00,0x66,0x66,0x6C,0x6C,0x78,0x6C,0x6C,0x66,0x66,0x00,0x00,0x00,0x00, /*---转换字符 L 44 ---*/ 0x00,0x00,0x00,0x60,0x60,0x60,0x60,0x60,0x60,0x60,0x60,0x7E,0x00,0x00,0x00,0x00, /*---转换字符 M 45 ---*/ 0x00,0x00,0x00,0x63,0x63,0x77,0x6B,0x6B,0x6B,0x63,0x63,0x63,0x00,0x00,0x00,0x00, /*---转换字符 N 46 ---*/ 0x00,0x00,0x00,0x63,0x63,0x73,0x7B,0x6F,0x67,0x63,0x63,0x63,0x00,0x00,0x00,0x00, /*---转换字符 O 47 ---*/ 0x00,0x00,0x00,0x3C,0x66,0x66,0x66,0x66,0x66,0x66,0x66,0x3C,0x00,0x00,0x00,0x00, /*---转换字符 P 48 ---*/ 0x00,0x00,0x00,0x7C,0x66,0x66,0x66,0x7C,0x60,0x60,0x60,0x60,0x00,0x00,0x00,0x00, /*---转换字符 Q 49 ---*/ 0x00,0x00,0x00,0x3C,0x66,0x66,0x66,0x66,0x66,0x66,0x66,0x3C,0x0C,0x06,0x00,0x00, /*---转换字符 R 50 ---*/ 0x00,0x00,0x00,0x7C,0x66,0x66,0x66,0x7C,0x6C,0x66,0x66,0x66,0x00,0x00,0x00,0x00, /*---转换字符 S 51 ---*/ 0x00,0x00,0x00,0x3C,0x66,0x60,0x30,0x18,0x0C,0x06,0x66,0x3C,0x00,0x00,0x00,0x00, /*---转换字符 T 52 ---*/ 0x00,0x00,0x00,0x7E,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x00,0x00,0x00,0x00, /*---转换字符 U 53 ---*/ 0x00,0x00,0x00,0x66,0x66,0x66,0x66,0x66,0x66,0x66,0x66,0x3C,0x00,0x00,0x00,0x00, /*---转换字符 V 54 ---*/

(28)

0x00,0x00,0x00,0x66,0x66,0x66,0x66,0x66,0x66,0x66,0x3C,0x18,0x00,0x00,0x00,0x00, /*---转换字符 W 55 ---*/ 0x00,0x00,0x00,0x63,0x63,0x63,0x6B,0x6B,0x6B,0x36,0x36,0x36,0x00,0x00,0x00,0x00, /*---转换字符 X 56 ---*/ 0x00,0x00,0x00,0x66,0x66,0x34,0x18,0x18,0x2C,0x66,0x66,0x66,0x00,0x00,0x00,0x00, /*---转换字符 Y 57 ---*/ 0x00,0x00,0x00,0x66,0x66,0x66,0x66,0x3C,0x18,0x18,0x18,0x18,0x00,0x00,0x00,0x00, /*---转换字符 Z 58 ---*/ 0x00,0x00,0x00,0x7E,0x06,0x06,0x0C,0x18,0x30,0x60,0x60,0x7E,0x00,0x00,0x00,0x00, /*---转换字符 [ 59 ---*/ 0x00,0x00,0x00,0x3C,0x30,0x30,0x30,0x30,0x30,0x30,0x30,0x30,0x30,0x30,0x3C,0x00, /*---转换字符 \ 60 ---*/ 0x00,0x00,0x00,0x60,0x60,0x30,0x30,0x18,0x18,0x0C,0x0C,0x06,0x06,0x00,0x00,0x00, /*---转换字符 ] 61 ---*/ 0x00,0x00,0x00,0x3C,0x0C,0x0C,0x0C,0x0C,0x0C,0x0C,0x0C,0x0C,0x0C,0x0C,0x3C,0x00, /*---转换字符 ^ 62 ---*/ 0x00,0x18,0x3C,0x66,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*---转换字符 _ 63 ---*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00, /*---转换字符 ` 64 ---*/ 0x00,0x38,0x18,0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*---转换字符 a 65 ---*/ 0x00,0x00,0x00,0x00,0x00,0x3C,0x06,0x06,0x3E,0x66,0x66,0x3E,0x00,0x00,0x00,0x00, /*---转换字符 b 66 ---*/ 0x00,0x00,0x00,0x60,0x60,0x7C,0x66,0x66,0x66,0x66,0x66,0x7C,0x00,0x00,0x00,0x00, /*---转换字符 c 67 ---*/ 0x00,0x00,0x00,0x00,0x00,0x3C,0x66,0x60,0x60,0x60,0x66,0x3C,0x00,0x00,0x00,0x00, /*---转换字符 d 68 ---*/ 0x00,0x00,0x00,0x06,0x06,0x3E,0x66,0x66,0x66,0x66,0x66,0x3E,0x00,0x00,0x00,0x00, /*---转换字符 e 69 ---*/ 0x00,0x00,0x00,0x00,0x00,0x3C,0x66,0x66,0x7E,0x60,0x60,0x3C,0x00,0x00,0x00,0x00, /*---转换字符 f 70 ---*/ 0x00,0x00,0x00,0x1E,0x30,0x30,0x30,0x7E,0x30,0x30,0x30,0x30,0x00,0x00,0x00,0x00, /*---转换字符 g 71 ---*/ 0x00,0x00,0x00,0x00,0x00,0x3E,0x66,0x66,0x66,0x66,0x66,0x3E,0x06,0x06,0x7C,0x00, /*---转换字符 h 72 ---*/ 0x00,0x00,0x00,0x60,0x60,0x7C,0x66,0x66,0x66,0x66,0x66,0x66,0x00,0x00,0x00,0x00, /*---转换字符 i 73 ---*/ 0x00,0x00,0x18,0x18,0x00,0x78,0x18,0x18,0x18,0x18,0x18,0x7E,0x00,0x00,0x00,0x00, /*---转换字符 j 74 ---*/ 0x00,0x00,0x0C,0x0C,0x00,0x3C,0x0C,0x0C,0x0C,0x0C,0x0C,0x0C,0x0C,0x0C,0x78,0x00, /*---转换字符 k 75 ---*/ 0x00,0x00,0x00,0x60,0x60,0x66,0x66,0x6C,0x78,0x6C,0x66,0x66,0x00,0x00,0x00,0x00, /*---转换字符 l 76 ---*/ 0x00,0x00,0x00,0x78,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x7E,0x00,0x00,0x00,0x00, /*---转换字符 m 77 ---*/ 0x00,0x00,0x00,0x00,0x00,0x7E,0x6B,0x6B,0x6B,0x6B,0x6B,0x63,0x00,0x00,0x00,0x00, /*---转换字符 n 78 ---*/ 0x00,0x00,0x00,0x00,0x00,0x7C,0x66,0x66,0x66,0x66,0x66,0x66,0x00,0x00,0x00,0x00, /*---转换字符 o 79 ---*/ 0x00,0x00,0x00,0x00,0x00,0x3C,0x66,0x66,0x66,0x66,0x66,0x3C,0x00,0x00,0x00,0x00, /*---转换字符 p 80 ---*/ 0x00,0x00,0x00,0x00,0x00,0x7C,0x66,0x66,0x66,0x66,0x66,0x7C,0x60,0x60,0x60,0x00, /*---转换字符 q 81 ---*/ 0x00,0x00,0x00,0x00,0x00,0x3E,0x66,0x66,0x66,0x66,0x66,0x3E,0x06,0x06,0x06,0x00, /*---转换字符 r 82 ---*/ 0x00,0x00,0x00,0x00,0x00,0x66,0x6E,0x70,0x60,0x60,0x60,0x60,0x00,0x00,0x00,0x00, /*---转换字符 s 83 ---*/ 0x00,0x00,0x00,0x00,0x00,0x3E,0x60,0x60,0x3C,0x06,0x06,0x7C,0x00,0x00,0x00,0x00, /*---转换字符 t 84 ---*/ 0x00,0x00,0x00,0x30,0x30,0x7E,0x30,0x30,0x30,0x30,0x30,0x1E,0x00,0x00,0x00,0x00, /*---转换字符 u 85 ---*/ 0x00,0x00,0x00,0x00,0x00,0x66,0x66,0x66,0x66,0x66,0x66,0x3E,0x00,0x00,0x00,0x00, /*---转换字符 v 86 ---*/ 0x00,0x00,0x00,0x00,0x00,0x66,0x66,0x66,0x66,0x66,0x3C,0x18,0x00,0x00,0x00,0x00, /*---转换字符 w 87 ---*/ 0x00,0x00,0x00,0x00,0x00,0x63,0x6B,0x6B,0x6B,0x6B,0x36,0x36,0x00,0x00,0x00,0x00, /*---转换字符 x 88 ---*/ 0x00,0x00,0x00,0x00,0x00,0x66,0x66,0x3C,0x18,0x3C,0x66,0x66,0x00,0x00,0x00,0x00, /*---转换字符 y 89 ---*/ 0x00,0x00,0x00,0x00,0x00,0x66,0x66,0x66,0x66,0x66,0x66,0x3C,0x0C,0x18,0xF0,0x00, /*---转换字符 z 90 ---*/ 0x00,0x00,0x00,0x00,0x00,0x7E,0x06,0x0C,0x18,0x30,0x60,0x7E,0x00,0x00,0x00,0x00, /*---转换字符 { 91 ---*/

(29)

0x00,0x00,0x00,0x0C,0x18,0x18,0x18,0x30,0x60,0x30,0x18,0x18,0x18,0x0C,0x00,0x00, /*---转换字符 | 92 ---*/ 0x00,0x00,0x00,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x18,0x00, /*---转换字符 } 93 ---*/ 0x00,0x00,0x00,0x30,0x18,0x18,0x18,0x0C,0x06,0x0C,0x18,0x18,0x18,0x30,0x00,0x00, /*---转换字符 ~ 94 ---*/ 0x00,0x00,0x00,0x71,0xDB,0x8E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*---转换字符 95 ---*/ 0x00,0x00,0x00,0x7E,0x7E,0x7E,0x7E,0x7E,0x7E,0x7E,0x7E,0x7E,0x00,0x00,0x00,0x00, };

14. USING LCD MODULES

14-1. Liquid Crystal Display Modules

LCD is composed of glass and polarizer. Pay attention to the following items when handling.

(1) Please keep the temperature within specified range for use and storage. Polarization degradation,

bubble generation or polarizer peel-off may occur with high temperature and high humidity.

(2) Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead

(glass, tweezers, etc.).

(3) N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and

reflectors made of organic substances which will be damaged by chemicals such as acetone, toluene,

ethanol and isopropylalcohol.

(4) When the display surface becomes dusty, wipe gently with absorbent cotton or other soft material

like chamois soaked in petroleum benzin. Do not scrub hard to avoid damaging the display surface.

(5) Wipe off saliva or water drops immediately, contact with water over a long period of time may

cause deformation or color fading.

(6) Avoid contacting oil and fats.

(7) Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the

polarizers. After products are tested at low temperature they must be warmed up in a container before

coming is contacting with room temperature air.

(8) Do not put or attach anything on the display area to avoid leaving marks on.

(9) Do not touch the display with bare hands. This will stain the display area and degradate

insulation between terminals (some cosmetics are determinated to the polarizers).

(10) As glass is fragile. It tends to become or chipped during handling especially on the edges. Please

avoid dropping or jarring.

14-2.Installing LCD Modules

The hole in the printed circuit board is used to fix LCM as shown in the picture below. Attend to the

following items when installing the LCM.

(1) Cover the surface with a transparent protective plate to protect the polarizer and LC cell.

(30)

fitting plate should have enough height to avoid causing stress to the module surface, refer to the

individual specifications for measurements. The measurement tolerance should be 0.1mm.

14-3. Precaution for Handing LCD Modules

Since LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive

shocks to the module or making any alterations or modifications to it.

(1) Do not alter, modify or change the shape of the tab on the metal frame.

(2) Do not make extra holes on the printed circuit board, modify its shape or change the positions of

components to be attached.

(3) Do not damage or modify the pattern writing on the printed circuit board.

(4) Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector.

(5) Except for soldering the interface, do not make any alterations or modifications with a soldering

iron.

(6) Do not drop, bend or twist LCM.

LCM is easy to be damaged. Please note below and be careful for handling.

Correct handling:

As above picture, please handle with anti-static gloves around LCM edges.

Incorrect handling:

Please don’t touch IC directly. Please don’t stack LCM.

(31)

Please don’t hold the surface of IC. Please don’t operate with sharp stick such as pens。

14-4.Electro-Static Discharge Control

Since this module uses a CMOS LSI, the same careful attention should be paid to electrostatic

discharge as for an ordinary CMOS IC.

(1) Make certain that you are grounded when handing LCM.

(2) Before remove LCM from its packing case or incorporating it into a set, be sure the module and

your body have the same electric potential.

(3) When soldering the terminal of LCM, make certain the AC power source for the soldering iron

does not leak.

(4) When using an electric screwdriver to attach LCM, the screwdriver should be of ground

potentiality to minimize as much as possible any transmission of electromagnetic waves produced

sparks coming from the commutator of the motor.

(5) As far as possible make the electric potential of your work clothes and that of the work bench the

ground potential.

(6) To reduce the generation of static electricity be careful that the air in the work is not too dried. A

relative humidity of 50%-60% is recommended.

14-5. Precaution for soldering to the LCM

(1) Observe the following when soldering lead wire, connector cable and etc. to the LCM.

- Soldering iron temperature : 280C  10C.

- Soldering time : 3-4 sec.

- Solder : eutectic solder.

If soldering flux is used, be sure to remove any remaining flux after finishing to soldering operation.

(This does not apply in the case of a non-halogen type of flux.) It is recommended that you protect the

LCD surface with a cover during soldering to prevent any damage dur to flux spatters.

(2) When soldering the electroluminescent panel and PC board, the panel and board should not be

detached more than three times. This maximum number is determined by the temperature and time

conditions mentioned above, though there may be some variance depending on the temperature of the

soldering iron.

(3) When remove the electoluminescent panel from the PC board, be sure the solder has completely

melted, the soldered pad on the PC board could be damaged.

14-6.Precautions for Operation

(1) Viewing angle varies with the change of liquid crystal driving voltage (VO). Adjust VO to show

the best contrast.

(2) Driving the LCD in the voltage above the limit shortens its life.

(3) Response time is greatly delayed at temperature below the operating temperature range. However,

this does not mean the LCD will be out of the order. It will recover when it returns to the specified

temperature range.

(32)

it will return to normal if it is turned off and then back on.

(5) Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit.

Therefore, it must be used under the relative condition of 40C , 50% RH.

(6) When turning the power on, input each signal after the positive/negative voltage becomes stable.

14-7. Storage

When storing LCDs as spares for some years, the following precaution are necessary.

(1) Store them in a sealed polyethylene bag. If properly sealed, there is no need for dessicant.

(2) Store them in a dark place. Do not expose to sunlight or fluorescent light, keep the temperature

between 0C and 35C.

(3) The polarizer surface should not come in contact with any other objects. (We advise you to store

them in the container in which they were shipped.)

(4) Environmental conditions :

- Do not leave them for more than 168hrs. at 60C.

- Should not be left for more than 48hrs. at -20C.

14-8. Safety

(1) It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with

solvents such as acetone and ethanol, which should later be burned.

(2) If any liquid leakes out of a damaged glass cell and comes in contact with the hands, wash off

thoroughly with soap and water.

14-9.Return LCM under warranty

No warranty can be granted if the precautions stated above have been disregarded. The typical

examples of violations are :

- Broken LCD glass.

- PCB eyelet’s damaged or modified.

- PCB conductors damaged.

- Circuit modified in any way, including addition of components.

- PCB tampered with by grinding, engraving or painting varnish.

- soldering to or modifying the bezel in any manner.

Module repairs will be invoiced to the customer upon mutual agreement. Modules must be returned

with sufficient description of the failures or defects. Any connectors or cable installed by the customer

must be removed completely without damaging the PCB eyelet’s, conductors and terminals.