STANDARDS FOR THE MATERIALS

(1)

Kpl Standardin numero Vahvistus-pvm

Otsikko Voimassa Uusi/korvaava standardi

STANDARDS FOR THE MATERIALS

1 EN 10204 2004-10 Metallic products.Types of inspection documents X

2 EN 10079 1992-10 Definition of steel products X

3 EN 10027-1 2005-08 Designation systems for steel. Part 1: Steel names, principal symbols X

4 EN 10027-2 1992-07 Designation systems for steel. Part 2: Numerical system X

5 EN 10056-1 1998-08 Structural steel equal and unequal leg angles Part 1: Dimensions X 6 EN 10056-2 1993-09 Structural steel equal and unequal leg angles Part 2: Tolerances on shape

and dimensions X

7 EN 10025 1990-03 Hot rolled products of non-alloy structural steels. Technical delivery conditions

EN 10025-1:2004 Hot rolled products of structural steels. Part 1: General technical delivery

conditions

EN 10025-2:2004 Hot rolled products of structural steels. Part 2: Technical delivery conditions for non-alloy structural steels + Korjaus EN 10025-2/AC:2005 8 EN 10029 1991-04 Hot rolled steel plates 3mm thick or above. Tolerances on dimensions, shape

and mass X

9 EN 10051 1997-09 Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy

steels. Tolerances on dimensions and shape X

10 EN 10034 1993-09 Structural steel I and H section- Tolerances on shape and dimensions X 11 EN 10163-1 2004-12 Delivery requirements for surface condition of hot rolled steel plates, wide

(2)

12 EN 10163-2 EN 10163-3

2004-12 Delivery requirements for surface condition of hot rolled steel plates, wide

flats and sections Part 2: Plate and wide flats X

13 EN 10219-1 2003-02 Cold formed welded structural hollow sections of non-alloy and fine grain steels Part 1 : Technical delivery requirements

EN 10219-1:2006-04

14 EN 10219-2 2003-02 Cold formed welded structural hollow sections of non-alloy and fine grain steels Part 2 : Tolerances, dimensions and sectional properties

EN 10219-1:2006-04

15 EN 10279 2000-01 Hot-rolled steel channels. Tolerances on shape, dimensions and mass X

16 EN 10113-1 1993-03 Hot-rolled products in weld able fine grain structural steels EN 10025-1:2004 Hot rolled

products of structural steels - Part 1: General technical delivery

conditions

EN 10025-3:2004 Hot rolled

products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels EN 10025-4:2004 Hot rolled

products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels

17 EN 10113-2 1993-03 Hot-rolled products in weld able fine grain structural steels EN 10025-1:2004 EN 10025-3:2004 18 EN 10113-3 1993-03 Hot-rolled products in weld able fine grain structural steels EN 10025-1:2004

EN 10025-4:2004 19 EN 10155 1993-06 Structural steels with improved athmospheric corrosion resistance. Technical

delivery conditions

EN 10025-5:2004 Hot rolled

products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance

(3)

pvm

20 ISO 4014 1999-09 Hexagon head bolts. Product grades A and B X

21 EN 24014 1991-10 Hexagon head bolts. Product grades A and B X

22 ISO 4017 1999-08 Hexagon head screws. Product grades A and B X

23 EN 24017 1991-10 Hexagon head screws. Product grades A and B X

24 ISO 4032 1999-08 Hexagon nuts, style 1. Product grades A and B X

25 EN 24032 1991-10 Hexagon nuts, style 1. Product grades A and B X

26 ISO 8992 2005-04 Fasteners. General requirements for bolts, screws, studs and nuts X

27 ISO 7091 2000-06 Plain washers. Normal series. Product grade C X

28 ISO 4759-1 2000-11 Tolerances for fasteners. Part 1: Bolts, screws, studs and nuts. Product

grades A, B and C X

29 EN 10130 + A1 1998-09 Cold rolled low carbon steel flat products for cold forming. Technical delivery

conditions X

Uusi versio valmistunee joulukuussa 2006

30 ISO 898-1 1999-08 Mechanical properties of fasteners made of carbon steel and alloy steel. Part

1: Bolts, screws and studs X

31 ISO 898-2 1992-11 Mechanical properties of fasteners. Part 2: Nuts with specified proof load

values. Coarse thread X

32 ISO 898-5 1998-08 Mechanical properties of fasteners made of carbon steel and alloy steel. Part

5: Set screws and similar threaded fasteners not under tensile stresses X 33 ISO 898-6 1994-12 Mechanical properties of fasteners. Part 6: Nuts with specified proof load

values. Fine pitch thread X

34 ISO 898-7 1992-11 Mechanical properties of fasteners. Part 7: Torsional test and minimum

torques for bolts and screws with nominal diameters 1 mm to 10 mm X 35

(4)

STANDARDS FOR THE WELDING PROCEDURE SPECIFICATION

36 EN 288-1 1992-02 Specification and qualification of welding procedures for metallic materials Part 1: General rules for fusion welding

EN ISO 15607:2003

37 EN 288-2 1992-02 Specification and qualification of welding procedures for metallic materials Part 2: Welding procedure specification for arc welding

EN ISO 15609-1:2004

38 EN 288-3 1992-02 Specification and qualification of welding procedures for metallic materials Part 3: Welding procedure tests for the arc welding of steels

EN ISO 15614-1:2004

39 EN 288-5 1994-08 Specification and qualification of welding procedures for metallic materials Part 5: Approval by using approved welding consumables for arc welding

EN ISO 15610:2003

40 EN 288-6 1994-08 Specification and qualification of welding procedures for metallic materials Part 6: Approval related to previous experience

EN ISO 15611:2003

41 EN 288-7 1995-05 Specification and qualification of welding procedures for metallic materials Part 7: Approval by a standard welding procedure for arc welding

EN ISO 15612:2004

42 EN 288-8 1995-05 Specification and qualification of welding procedures for metallic materials Part 8: Approval by a pre-production welding test

EN ISO 15613:2004

43 EN 29692 1994-02 Metal- arc welding with covered electrode, gas-shielded metal-arc and gas welding. Joint preparations for steel

EN ISO 9692-1:2003 Welding and allied processes. Recommendations for joint preparation. Part 1: Manual metal-arc welding, gas-shielded metal-arc welding, gas welding, TIG welding and beam welding of steels 44 EN ISO 9692-2 1998-04 Welding and allied processes. Joint preparations Part 2: Submerged arc

welding of steels X

+ Korjaus EN ISO 9692-2/AC:1999

45 EN ISO 13920 1996-08 Welding. General tolerances for welded constructions. Dimensions for lengths

and angles. Shape and position X

46 ENV 1090-1 1996-04 Execution of steel structures Part 1: General rules and rules for buildings X 47 SFS-EN 1011-1 1998-08 Welding. Recommendations for welding of metallic materials. Part 1: General

guidance for arc welding X

+ Lisäys A1:2002-09 + Lisäys A2:2004-02

(5)

pvm

48 SFS-EN 1011-2 2001-05 Welding. Recommendations for welding of metallic materials. Part 2: Arc

welding of ferritic steels X + Lisäys A1:2004-02

welding of stainless steels X + Lisäys A1:2004-02

welding of aluminium and aluminium alloys X + Lisäys A1:2004-02

51 SFS-EN 1011-5 2003-12 Welding. Recommendations for welding of metallic materials. Part 5: Welding

of clad steel X

52 SFS-EN 1011-6 2006-01 Welding. Recommendation for welding of metallic materials. Part 6: Laser

beam welding X

53 SFS-EN 1011-7 2004-09 Welding. Recommendations for welding of metallic materials. Part 7: Electron

beam welding X

54 SFS-EN 1011-8 2005-03 Welding. Recommendations for welding of metallic materials. Part 8: Welding

of cast irons X

55 SFS-EN 439 1995-02 Welding consumables. Shielding gases for arc welding and cutting X 56 SFS-EN ISO 4063 2000-05 Welding and allied processes. Nomenclature of processes and reference

numbers X

57 SFS-EN ISO 6947 1997-08 Welds. Working positions. Definitions of angles of slope and rotation X 58 EN ISO 15607 2003-12 Welding Specification and qualification of welding procedures for metallic

materials. General rules X

59 CEN ISO/TR 15608 2005-10 Welding. Guidelines for a metallic materials grouping system X 60 SFS-EN ISO 15609-1 2004-11 Specification and qualification of welding procedures for metallic materials.

Welding procedure specification. Part 1: Arc welding X 61 SFS-EN ISO 15609-2 2002-03 Specification and qualification of welding procedures for metallic materials.

Welding procedure specification. Part 2: Gas welding X 62 SFS-EN ISO 15609-3 2004-09 Specification and qualification of welding procedures for metallic materials.

Welding procedures specification. Part 3: Electron beam welding X 63 SFS-EN ISO 15609-4 2004-09 Specification and qualification of welding procedures for metallic materials.

Welding procedure specification. Part 4: Laser beam welding X 64 SFS-EN ISO 15609-5 2004-09 Specification and qualification of welding procedures for metallic materials.

(6)

65 EN ISO 15610 2003-11 Specification and qualification of welding procedures for metallic materials.

Qualification based on tested welding consumables X

Qualification based on previous welding experience X

Qualification by adoption of a standard welding procedure X 68 EN ISO 15613 2004-06 Specification and qualification of welding procedures for metallic materials.

Qualification based on pre-production welding test X

69 ISO 15614-1 2004-06 Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys

X

+ Corrigendum 1:2005

70 ISO 15614-2 2005-05 Specification and qualification of welding procedures for metallic materials.

Welding procedure test. Part 2: Arc welding of aluminium and its alloys X

+ Corrigendum 1:2005

Welding procedure test. Part 4: Finishing welding of aluminium castings X 72 ISO 15614-5 2004-03 Specification and qualification of welding procedures for metallic materials.

Welding procedure test. Part 5: Arc welding of titanium, zirconium and their alloys

X

73 ISO 15614-8: 2002-04 Specification and qualification of welding procedures for metallic materials.

Welding procedure test. Part 8: Welding of tubes to tube-plate joints X 74 ISO 15614-10 2005-02 Specification and qualification of welding procedures for metallic materials.

Welding procedure test. Part 10: Hyperbaric dry welding X 75 ISO 15614-11 2002-03 Specification and qualification of welding procedures for metallic materials.

Welding procedure test. Part 11: Electron and laser beam welding X 76 ISO 15614-12 2004-08 Specification and qualification of welding procedures for metallic materials.

Welding procedure test. Part 12: Spot, seam and projection welding X 77 ISO 15614-13 2005-02 Specification and qualification of welding procedures for metallic materials.

(7)

pvm

Welding procedure test. Part 6: Arc and gas welding of copper and its alloys X 79 EN ISO 14555 1998-10 Welding. Arc stud welding of metallic materials

X Uusi versio valmistunee sysksyn aikana

80 EN ISO 15620 2000-07 Welding. Friction welding of metallic materials X

STANDARDS FOR THE PREPARATION OF STEEL

81 ISO 9223 1992-02 Corrosion of metals and alloys. Corrosivity of atmospheres. Classification X 82 EN 10238 1996-09 Automatically blast-cleaned and automatically prefabrication primed structural

steel products X

83 ISO 8501-1 1988-12 Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings

X

Uusi versio ilmestynee lähiaikoina

84 ISO 8501-2 1994-12 Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Part 2: Preparation grades of previously coated steel substrates after localized removal of previous coatings

X

85 ISO 8501-3 2001-12 Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Part 3: Preparation grades of welds, cut, edges and other areas with surface imperfections

ISO 8501-3:2006-03 Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Part 3: Preparation grades of welds, edges and other areas with surface imperfections 86 ISO 8503-1 1988-02 Preparation of steel substrates before application of paints and related

products. Surface roughness characteristics of blast-cleaned steel substrates. Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces

(8)

87 ISO 8503-2 1988-02 Preparation of steel substrates before application of paints and related products. Surface roughness characteristics of blast-cleaned steel substrates. Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel

X

88 ISO 8503-3 1988-02 Preparation of steel substrates before application of paints and related products. Surface roughness characteristics of blast-cleaned steel substrates. Part 3: Method for the calibration of ISO reference comparators and for determination of surface profile. Focusing microscope procedure

X

89 ISO 8503-4 1988-02 Preparation of steel substrates before application of paints and related products. Surface roughness characteristics of blast-cleaned steel substrates. Part 4: Method for the calibration of ISO reference comparators and for determination of surface profile. Stylus instrument procedure

X

90 EN ISO 8504-1 2001-05 Preparation of steel substrates before application of paints and related

products. Surface preparation methods. Part1: General principles X 91 EN ISO 8504-2 2001-05 Preparation of steel substrates before application of paints and related

products. Surface preparation methods. Part 2: Abrasive blast cleaning X 92 EN ISO 8504-3 2001-05 Preparation of steel substrates before application of paints and related

products. Surface preparation methods. Part 3: Hand- and power- tools cleaning

X

93 ISO 4628-1 2003-09 Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 1: General principles and rating schemes

X

94 ISO 4628-2 2003-09 Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 2: Designation of degree of blistering

X

95 ISO 4628-3 2003-09 Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 3: Designation of degree of rusting

X

96 ISO 4628-4 2003-09 Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 4: Designation of degree of cracking

(9)

pvm

97 ISO 4628-5 2003-09 Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 5: Designation of degree of flaking

X

98 EN ISO 9013 2002-09 Welding and allied processes. Quality classification and dimensional

tolerances of thermally cut (oxygen/fuel gas flame) surfaces X

+ Lisäys A1:2003

99 EN ISO 12944-1 1998-05 Paints and varnishes. Corrosion protection of steel structures by protective

paint systems. Part 1: General introduction X

paint systems. Part 2: Classification of environments X 101 EN ISO 12944-3 1998-05 Paints and varnishes. Corrosion protection of steel structures by protective

paint systems. Part 3: Design considerations X

paint systems. Part 4: Types of surface and surface preparation X 103 EN ISO 12944-5 1998-05 Paints and varnishes. Corrosion protection of steel structures by protective

paint systems. Part 5: Protective paint system X

paint systems. Part 6: Laboratory performance test methods X 105 EN ISO 12944-7 1998 Paints and varnishes. Corrosion protection of steel structures by protective

paint systems. Part 7: Execution and supervision of paint work X 106 EN ISO 12944-8 1998-05 Paints and varnishes. Corrosion protection of steel structures by protective

paint systems. Part 8: Development of specifications for new work and maintenance

X

107 EN ISO 1460 1994-10 Metallic coatings. Hot dip galvanized coatings on ferrous materials.

Gravimetric determination of the mass per unit area (ISO 1460:1992) X 108 EN ISO 1461 1999-02 Hot dip galvanized coatings on fabricated iron and steel articles.

Specifications and test methods X

109 EN ISO 14713 1999-03 Protection against corrosion of iron and steel in structures. Zinc and

(10)

110 ISO 7413 1984-11 Hexagon nuts for structural bolting, style 1, hot-dip galvanized (oversize

tapped). Product grades A and B. Property classes 5, 6 and 8 X

111 ISO 2808 Paints and varnishes -- Determination of film thickness X

112 EN ISO 2178 1995-01 Non-magnetic coatings on magnetic substrates. Measurement of coating

thickness- Magnetic method X

113 EN ISO 2064 2000-03 Metallic and other inorganic coatings. Definitions and conventions concerning

the measurement of thickness X

114 ISO 15184 1998-11 Paints and varnishes. Determination of film hardness by pencil test X

115 ISO 7253 1996-12 Paints and varnishes. Determination of resistance to neutral salt spray (fog) ISO 9227:2006 Corrosion tests in artificial atmospheres.Salt spray tests

116 SFS-EN ISO 4892-1 2001-01 Plastics. Methods of exposure to laboratory light sources. Part 1: General

guidance X

117 SFS-EN ISO 4892-2 2006-08 Plastics. Methods of exposure to laboratory light sources. Part 2: Xenon-arc

lamps X

118 SFS-EN ISO 4892-3 2006-08 Plastics. Methods of exposure to laboratory light sources. Part 3: Fluorescent

UV lamps X

STANDARDS FOR THE QUALITY REQUIRMENTS

119 EN 729-1 1994-09 Quality requirements for welding. Fusion welding of metallic materials. Part 1: Guidelines for selection and use

EN ISO 3834-1:2005 Quality requirements for fusion welding of metallic materials. Part 1: Criteria for the selection of the appropriate level of quality requirements 120 EN 729-3 1994-09 Quality requirements for welding. Fusion welding of metallic materials. Part 3:

Standard quality requirements

EN ISO 3834-3:2005 Quality requirements for fusion welding of metallic materials. Part 3: Standard quality requirements

(11)

pvm

121 EN 729-4 1994-09 Quality requirements for welding. Fusion welding of metallic materials. Part 4: Elementary quality requirements

EN ISO 3834-4:2005 Quality requirements for fusion welding of metallic materials. Part 4:

Elementary quality requirements

122 EN 719 1994-08 Welding coordination. Tasks and responsibilities X

123 EN 287-1 1992-02 Approval testing of welders. Fusion welding. Part 1: Steels EN 287-1:2004 Qualification test of welders. Fusion welding. Part 1: Steels

+ Korjaus AC:2004 + Lisäys A2:2006 124 EN 1418 1997-12 Welding personnel. Approval testing of welding operators for fusion welding

and resistance weld setters for fully mechanized and automatic welding of metallic materials

X

125 EN 473 1993-01 Qualification and certification of NDT personel. General principles EN 473:2000 Non destructive testing. Qualification and certification of NDT personnel. General principles

+ Lisäys A1:2005

STANDARDS FOR THE QUALITY LEVEL

126 EN 25817 1992-07 Arc-welded joints in steel. Guidance on quality levels for imperfection EN ISO 5817:2003 Welding. Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded). Quality levels for imperfections

+ Korjaus AC:2006

STANDARDS FOR THE INSPECTION INSTRUCTION

127 EN 12062 1997-08 Non-destructive examination of welds. General rules for metallic materials _X + Lisäys A1:2002 + Lisäys A2:2003 128 EN 970 1997-02 Non–destructive examination of fusion welds. Visual examination X

129 EN ISO 6520-1 1998-10 Welding and allied processes. Classification of geometrical imperfections in

(12)

130 SFS-EN 1289 1998-08 Non-destructive examination of welds. Penetrant testing of welds. Acceptance

levels X

+ Lisäys A1:2002 + Lisäys A2:2004 131 SFS-EN 571-1 1997-08 Non destructive testing. Penetrant testing. Part 1: General principles X

132 EN 1290 1998-02 Non-destructive examination of welds. Magnetic particle examination of welds _X + Lisäys A1:2002 + Lisäys A2:2003 133 EN 1291 1998-02 Non-destructive examination of welds. Magnetic particle testing of welds.

Acceptance levels X

+ Lisäys A1:2002 + Lisäys A2:2003 134 SFS-EN 1435 1998-01 Non-destructive examination of welds. Radiographic examination of welded

joints X

+ Lisäys A1:2002 + Lisäys A2:2004 135 EN 12517-1 2006-03 Non-destructive testing of welds. Part 1: Evaluation of welded joints in steel,

nickel, titanium and their alloys by radiography. Acceptance levels X 136 SFS-EN 1712 1998-03 Non-destructive examination of welds. Ultrasonic examination of welded

joints. Acceptance levels X

+ Lisäys A1:2002 + Lisäys A2:2004 137 SFS-EN 1713 1998-12 Non-destructive examination of welds. Ultrasonic examination _X + Lisäys A1:2002 + Lisäys A2:2004 138 SFS-EN 1714 1998-03 Non-destructive examination of welds. Ultrasonic examination of welded

joints X

+ Lisäys A1:2002 + Lisäys A2:2004

139 SFS-EN 13480-1 2002-09 Metallic industrial piping. Part 1: General X + Lisäys A1:2006

140 SFS-EN 13480-2 2002-12 Metallic industrial piping. Part 2: Materials X

141 SFS-EN 13480-3 2002-09 Metallic industrial piping. Part 3: Design and calculation X + Lisäys A1:2006 142 SFS-EN 13480-4 2002-09 Metallic industrial piping. Part 4: Fabrication and installation X

143 SFS-EN 13480-5 2002-09 Metallic industrial piping. Part 5: Inspection and testing X

144 SFS-EN 13480-6 2005-03 Metallic industrial piping. Part 6: Additional requirements for buried piping X + Lisäys A1:2006 145 CEN/TR 13480-7 2002-05 Metallic industrial piping. Part 7: Guidance on the use of conformity

assessment procedures X

146 SFS-EN 1043-1 1996-05 Destructive tests on welds in metallic materials. Hardness testing. Part 1:

(13)

pvm

147 SFS-EN 1043-2 1997-05 Destructive tests on welds in metallic materials. Hardness test. Part 2: Micro

hardness testing on welded joints X

148 EN 444 1994-02 Non-destructive testing. General principles for radiographic examination of

metallic materials by X- and gamma-rays X

STANDARDS FOR THE DESIGN

149 ISO 14122-1 2001-05 Safety of machinery. Permanent means of access to machines and industrial

plants. Part 1: Choice of a fixed means of access between two levels X 150 ISO 14122-2 2001-05 Safety of machinery. Permanent means of access to machines and industrial

plants. Part 2: Working platforms and Walkways X

151 ISO 14122-3 2001-05 Safety of machinery. Permanent means of access to machines and industrial

plants. Part 3: Stairways, stepladders and guardrails X 152 ISO 14122-4 2004-12 Safety of machinery. Permanent means of access to machines and industrial

plants. Part 4: Fixed ladders X

153 ISO 2553 1992-10 Welded, brazed and soldered joints. Symbolic representation on drawings X 154 EN 22553 1994-05 Welded, brazed and soldered joints. Symbolic representation on drawings

(ISO 2553:1992) X

155 ISO 4354 1997-07 Wind actions on structures (Relationship between reference velocity

pressure… ) X

156 SFS-ENV 1993-1-1 1993-11 Eurocode 3: Design of steel structures. Part 1-1: General rules and rules for buildings

X

Korvataan standardeilla SFS-EN 1:2005, SFS-EN 1993-1-8:2005, SFS-EN 1993-1-9:2005 ja SFS-EN 1993-1-10:2005 viimeistään 2010-03-31 157 SFS-ENV 1993-1-1/A1 D

1996-03 Eurocode 3: Design of steel structures. Part 1-1: General. General rules and

rules for buildings X

Korvataan standardilla SFS-EN 1993-1-1:2005 viimeistään 2010-03-31

(14)

158 SFS-ENV 1993-1-1/A2 G

1999-11 Eurocode 3: Design of steel structures. Part 1-1: General rules and rules for

buildings. Annex G: Design for torsion resistance X ---”---

159 SFS-ENV 1993-1-1/A2 H

buildings. Annex H: Modelling of building structures for analysis X

---”---

160 SFS-ENV 1993-1-1/A2 J

1999-11 Eurocode 3: Design of steel structures. Part 1-1: General. General rules and

rules for buildings X ---”---

161 SFS-ENV 1993-1-1/A2 N

buildings. Annex N: Opening in webs X ---”---

162 SFS-ENV 1993-1-1/A2 Z

buildings. Annex Z: Determination of design resistance from tests X

---”---

163 SFS-ENV 1993-1-2 1996-09 Eurocode 3. Design of steel structures. Part 1-2: General rules. Structural fire design

X

Korvataan standardilla SFS-EN 1993-1-2:2005 viimeistään 2010-03-31

164 SFS-ENV 1993-1-4 1999-02 Eurocode 3: Design of steel structures. Part 1-4: General rules. _{Supplementary rules for stainless steels} X 165 SFS-ENV 1993-1-5 1999-02 Eurocode 3: Design of steel structures. Part 1-5: General rules.

Supplementary rules for planar plated structures without transverse loading X 166 SFS-ENV 1993-3-1 1999-02 Eurocode 3: Design of steel structures. Part 3-1: Towers, masts and

chimneys. Towers and masts X

167 SFS-ENV 1991-1 1995-10 Eurocode 1: Basis of design and actions on structures. Part 1: Basis of design X Korvataan standardilla SFS-EN 1990:2002 viimeistään 2010-03-31 168 SFS-EN 1991-1-1 2002-10 Eurocode 1: Actions on structures. Part 1-1: General actions. Densities,

self-weight, imposed loads for buildings X

169 SFS-EN 1991-1-2 2003-04 Eurocode 1. Actions on structures. Part 1-2: General actions. Actions on

structures exposed to fire X

170 SFS-EN 1991-1-3 2004-01 Eurocode 1: Actions on structures. Part 1-3: General actions. Snow loads X 171 SFS-EN 1991-1-4 2005-09 Eurocode 1: Actions on structures. Part 1-4: General actions. Wind actions X 172 SFS-EN 1991-1-5 2004-05 Eurocode 1: Actions on structures. Part 1-5: General actions. Thermal actions X 173 SFS-EN 1991-1-6 2005-08 Eurocode 1. Actions on structures Part 1-6: General actions. Actions during

(15)