SBG3300-N Series. Wireless N VDSL2 Combo WAN Small Business Security Gateway DEFAULT LOGIN DETAILS. Firmware Version 1.20 Edition 3, 3/2015

(1)

(2)

Wireless N VDSL2 Combo WAN

Small Business Security Gateway

Firmware Version 1.20 Edition 3, 3/2015

DEFAULT LOGIN DETAILS IP Address: http://192.168.1.1

User Name: admin

Password: 1234

(3)

Device Panels

POWER

ETHERNET 1-4

WLAN ETHERNET

INTERNET

DSL WAN

DSL USB

ETHERNET 1-4

ETHERNET WAN

RESET ON/OFF

POWER MOBILE

USB MOBILE

(4)

Requirements

Make sure you have the following things before you start:

• INTERNET ACCESS: You need an Internet account with an ISP (Internet Service Provider) and information such as your user name, password, and so on.

• WEB BROWSER: Internet Explorer 6.0 and later versions, with JavaScript enabled, or Mozilla Firefox 3 and later versions, or Safari 2.0 and later versions. The browser will be used to access the Internet and/or access the Device’s Web Configurator.

Hardware Setup

Remove the Device’s clear plastic covers before using it.

To connect your Device:

3

4

5

6

1

7

(5)

1. Attach the antennas and point them up.

2. Do one of the following for your Internet connection:

a. DSL: Use a telephone cable to connect your Device’s DSL port to a telephone jack (or the DSL or modem jack on a splitter if you have one).

b. ETHERNET WAN: If you already have a broadband router or modem, use an Ethernet cable to connect the ETHERNET WAN port to it for Internet access.

3. ETHERNET: Use an Ethernet cable to connect a computer to an Ethernet port for initial configuration and/or Internet access.

4. USB: Connect a USB (version 2.0 or lower) memory stick or a USB hard drive for file sharing. The Device automatically detects the USB device.

5. MOBILE: Insert a 3G adapter to access the Internet wirelessly via a 3G network. The Device uses this 3G WAN connection as a backup when the DSL/Ethernet WAN connection fails.

6. POWER: Use the provided power adaptor to connect the POWER socket to an appropriate power source. Make sure the power at the outlet is on. After connecting the power adaptor, look at the lights on the front panel.

• The POWER light blinks while your Device starts up and then stays on once it is ready.

• Each LAN light stays on if the corresponding Ethernet port is properly connected and blinks when there is traffic.

• The ETHERNET WAN light stays on if the ETHERNET WAN port is properly connected and blinks when there is traffic.

• The USB light turns on when your Device detects a connected USB device and blinks when there is traffic.

• The MOBILE light turns on when your Device detects a connected 3G adapter and blinks when there is traffic.

(6)

• The DSL light is green when your Device has an ADSL connection. It is orange when you have a VDSL connection.

• The WLAN light flashes green when WLAN is activated and orange while WPS is in process. It stays on green when the wireless LAN is ready and blinks when there is traffic.

• The INTERNET light turns on when the gateway is able to access the Internet and will blink when your Device is sending or receiving data.

If the lights do not come on, check your connections and inspect your cables for damage. If the lights are still off, contact technical support.

a. Network standby power consumption < 12 W b. Off mode power consumption < 0.5 W

Set Up a Wireless Network

You can set up a wireless network manually. The wireless LAN on your Device is enabled by default. If the WLAN light is off, press the WLAN button at the front of the Device for one second. Once the WLAN light turns green, the wireless network is active. Use the Network Setting > Wireless > General screen to enable or disable this button.

To add a wireless client to the network, use the settings found on the side panel of your Device, which will look similar to the following example:

Configure wireless devices that you want to connect to the wireless network to use the same wireless settings as the Device.

The default wireless settings vary for each Device. Refer to the rear panel of your device and use the provided information.

SSID: ZyXEL00561

Security Mode: WPA2-PSK Pre-Shared Key: FB373BD356

(7)

The Web Configurator

The Web Configurator is a web browser tool that allows you to configure the Device. The computer and the Device need to be in the same IP address range to use this tool.

1. Open your browser and enter http://192.168.1.1 (the Device’s default IP address) as the address.

2. Enter the default user name admin and password 1234. Click Login.



If the login screen does not open, make sure you allow web browser pop-up windows, JavaScript and Java permissions. Your computer should be also set to get an IP address automatically from a DHCP server. See the appendices in your User’s Guide for more

information.

(8)

3. In the next screen, you can change the login password. This is

recommended. Enter your new password in the New Password field. Re- type your new password in the second field and then click Apply. If you prefer not to change the password, leave the two fields blank and click Skip.

4. The Status screen displays, where you can view the Device’s device, interface, and system information.

(9)

5. Click the Quick Start Wizard icon on the upper right corner of the screen.

Follow the directions to configure the Device’s time zone, Internet access, and wireless settings.

See your User’s Guide for how to use the rest of the Web Configurator screens.

You will need to refer to the section on how to setup the Broadband connection if the INTERNET LED (light) remains off.

EU Importer: ZyXEL Communications A/S Generatorvej 8D, 2860 Søborg, Denmark | http://www.zyxel.dk

US Importer: ZyXEL Communications, Inc | 1130 North Miller Street Anaheim,

Procedure to View a Product’s Certification(s) 1. Go to www.zyxel.com.

2. Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.

3. Select the certification you wish to view from this page.

(10)

www.zyxel.com

Declaration of Conformity

We herewith declare that this declaration is issued under our sole responsibility烉

Product 烉 Wireless N VDSL2 Combo WAN Small Business Security Gateway Model 烉 SBG3300-N000

MANUFACTURED BY AND TCF FILE LOCATED AT烉烉 Company 烉 ZyXEL Communications Corporation

Address 烉 1.No. 2, Gongye E. 9th Road, Hsinchu Science Park, Hsinchu, Taiwan, R.O.C.

2.No. 6, Innovation Road II, Hsinchu Science Park, Hsinchu, Taiwan, R.O.C.

3.*HQHUDWRUYHM'6¡ERUJ'HQPDUN

complies with essential requirements of the following EU harmonization legislation and in conformity with the following presumption of conformity烉

Essential requirements Presumption of conformity Directive 2006/95/EC

(LVD)

EN 60950-1:2006+A11:2009+A1:2010+A12:2011

Directive 2004/108/EC (EMC)

EN 55022:2010+AC:2011

EN 61000-3-2:2006+A1:2009+A2:2009 EN 61000-3-3:2008

EN 55024:2010 EN 301 489-1 V1.9.2 EN 301 489-17 V2.2.1 Directive 1999/5/EC

(R&TTE)

EN 300 328 V1.8.1

Directive 2011/65/EU (RoHS)

EN 50581:2012

Directive 2009/125/EC (ErP)

EN 50564:2011 EN 50563:2011 Recommendation 1999/519/EC

(EMF)

EN 62311:2008

ZyXEL Communications Corporation

2014-12-08

Date of issue Richard Hsu / Senior Manager

Quality Management Division

(11)