Thermal Night Vision Camera

Thermal Night Vision Camera

Thermal Night Vision Camera

Copyright

©2011 Samsung Techwin Co., Ltd. All rights reserved. Trademark

is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.

Warranty

If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:

To h ■ S • ■ M • •

Before operating the camera, confirm the camera model and correct input power voltage. To help you understand this manual thoroughly, we’ll introduce our model description.

■ SCB-9060/9080 SERIES

• NTSC MODEL • PAL MODEL SCB-9060/9080N SCB-9060/9080P ■ MODEL DESCRIPTION • SCB-9060/9080X SIGNAL SYSTEM • SIGNAL SYSTEM N→NTSC MODEL P→PAL MODEL

Safety information

CAUTION

DO NOT OPEN

CAUTION:

COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

To prevent damage which may result in fi re or electric shock hazard, do not expose this appliance to rain or moisture.

To prevent injury, this apparatus must be securely attached to the fl oor/wall in accordance with the installation instructions.

WARNING

Be sure to use only the standard adapter that is specifi ed in the specifi cation sheet. Using any other adapter could cause fi re, electrical shock, or damage to the product. Incorrectly connecting the power supply or replacing battery may cause explosion, fi re, electric shock, or damage to the product.

Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or fi re.

Securely plug the power cord into the power receptacle. insecure connection may cause fi re.

When installing the camera, fasten it securely and fi rmly. The fall of camera may cause personal injury. • • 1. 2. 3. 4. 5. fi e e s d CA s A A s T 6. 7. 8. 9. 10. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

● SAFETY INFORMATION ctric nce the e e

Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers fi lled with water on top of the camera. doing so may cause personal injury due to fi re, electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations. doing so may cause fi re or electric shock.

If any unusual smells or smoke come from the unit, stop using the product. in such case, immediately disconnect the power source and contact the service center. continued use in such a condition may cause fi re or electric shock.

If this product fails to operate normally, contact the nearest service center. never disassemble or modify this product in any way. (samsung is not liable for problems caused by unauthorized modifi cations or attempted repair.)

When cleaning, do not spray water directly onto parts of the product. doing so may cause fi re or electric shock.

CAUTION

Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to excessive vibrationor magnetic interference.

Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fi re or electric shock.

If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.

Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause fi re or damage to the product.

Keep out of direct sunlight and heat radiation sources. It may cause fi re. Install it in a place with good ventilation.

Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the CCD image sensor.

Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at any time. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CCD. 6. 7. 8. 9. 10. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

Safety information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :

This device may not cause harmful interference, and

This device must accept any interference received including interference that may cause undesired operation.

CAUTION

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

IC Compliance Notice

This Class A digital apparatus meets all requirements of the Canadian Interference.-Causing Equipment Regulations of ICES-003. 1)

2)

Correct disposal of batteries in this product

(Applicable in the European Union and other European countries with separate battery return systems.) This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health

Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Im

● SAFETY INFORMATION two use e s alth es , able ent

Important safety instructions

Keep these instructions. Heed all warnings. Follow all instructions.

Do not use this apparatus near water. Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specifi ed by the manufacturer. Use only with cart, stand, tripod, bracket, or table specifi ed by the

manufacturer, or sold with the apparatus.

Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be placed on the apparatus 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.

Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment, and is taking a number of steps to provide customers with more environment-friendly products.The Eco mark represents

INTRODUCTION

9

9 Features

10 What’s included

11 Component names and

Functions

INSTALLATION

15

15 Inputting Power

15 Startup

15 NUC(non uniformity correction)

16 Monitor/Communications Connection 17 Monitoring Guidelines 17 Storage

SETUP

18

18 Menu Confi guration

18 Function Settings Methods

TROUBLESHOOTING

26

FE

SPECIFICATIONS

27

●

INTRODUCTION

n)

FEATURES

Thermal Night Vision Camera

The SCB-9060/9080 Thermal Night Vision Camera is a contactless monitoring device capable of measuring the surface temperatures of all target areas, and displaying the resulting data via temperature distribution images (thermal images).

Featured by the top-notch uncooled IR detector, the sensor does not require you to prepare a separate cooling device or maintenance. In addition, its sensor boasts long wavelength sensitivity (detecting infrared radiation with wavelengths between 8-14 μm from targets and background), allowing it to produce high resolution thermal images with minimal impact from sunlight, even during outdoor daytime monitoring in clear weather.

Excellent Detection

Up to 380m of detection without lighting: SCB - 9060 Up to 1.2km of detection without lighting: SCB - 9080

Detection of over-specifi ed temperature

You can specify a specifi c temperature, over which you can instruct the camera to detect a target.

IFOV - Instantaneous Field of View (Spatial Resolution)

Featured by a small high-performance IR sensor with 0.47mrad/1.68mrad of IFOV (Instantaneous Field of View), the product can implement recording a sharper and more precise image against other cameras in the same class.

Dustproof, waterproof (IP66 standard certifi ed)

With dustproof and waterproof design, it can be installed in an outdoor place exposed to dust and rain.

Communications

Remote control of OSD menus is enabled via coaxial and RS-485 communication protocols.

- Protocol: Pelco Coaxitron

- RS-485 communication protocol: SAMSUNG-T, SAMSUNG-E, PELCO-D, PELCO-P, BOSCH, HONEYWELL, VICON, PANASONIC, GE, AD

OSD

The camera control is convenient by using 19 different foreign language O.S.D. - English, Korean, German, Spanish, Italian, Chinese, Russian, Polish, Japanese, French,

Turkish, Czech, Portuguese, Rumanian, Serbian, Taiwanese, Danish, Swedish, Thai y y y y y y y

Introduction

WHAT’S INCLUDED

Check if the following items are included in the product package.

A ( ) 이 기기는 업무용으로 전자파 적합등록을 한 기기이오니 판매자 또는 사 용자는 이 점을 주의하시기 바라며 만약 잘못 판매 또는 구입하였을때에는 가정용으로 교환하시기 바랍니다. www.samsungcctv.co.kr 본 제품은 대한민국에서만 사용하도록 만들어져 있으며, 해외에서는 품질을 보증하지 않습니다. FOR KOREA UNIT STANDARD ONLY Thermal Night Vision Camera 제품 사용 설명서 SCB-9060

SCB-9080

SCB-9060/9080,

camera sun shield User Manual Set of Wrench (x3)

Lens cap Bracket Screws (x2) Camera Holder Screws (x4)

CO

●

INTRODUCTION

COMPONENT NAMES AND FUNCTIONS

Names of external camera parts

➊Lens (SCB-9060 : 14mm, SCB-9080 : 50mm)

➋ Sun Shield

➌ Video signal/communications(RS485) cable

➍ Power cable(AC24V,50/60Hz)/ALARM Port

➎ Support platform for fastening camera

➌ ➍ ➎

Rear Terminal Placement

②Function Setup switch

③Terminal Block A

PIN Name Explanation

1 TRX+ RS485 + Communications Non-inverting input/output 2 TRX- RS485 - Communications Non-inverting input/output 3 VIDEO Output of video signal

4 GND Earth-grounding of video signal ④Terminal Block B

PIN Name Explanation

1 PW+ Power input AC+24V 2 PW- Power input AC+24V

3 NC

4 NC

5 NC

6 ALARM ALARM OUT + 7 ALARM ALARM OUT

-②

●

INTRODUCTION

Connector specifications and signals

Function Explanation Notes

RS485 I/F (TRX+, TRX-)

Because Half-duplex communication is supported, this function is used to update F/W.

Standard users should utilize the same cables as those employed at the time of shipment.

Communication terminator settings: - Default value: ON

- If multiple cameras are installed : Turn only the camera measuring the

furthest distance ON, and the remaining cameras OFF. Video output

(Video)

Acts as a composite video signal output.

Switch between NTSC/PAL using the menu.

Power supply

(PW+/-) Power Connection Port AC24V,50/60Hz

LED

Notifies users using the LED display whether the power is ON/OFF, and whether a device abnormality or warning has occurred.

Power ON : Lighting Device Abnormality/Warning : Flashing

Introduction

Assembly/Adjustment Methods

❶ A screw to fix the focus is located on the bottom of the lens.

➋ A sun shield is provided with this camera to allow for outdoor installation.

Using the bolts and hexagon wrenches included in this package, fasten the camera unit and sun shield firmly in place. (Do not use excessive force during assembly.)

Do not adjust the focus after purchasing this product, because it will have been set to the optimum position. Incorrectly adjusting the focus will hinder the camera’s performance.

I

IN

ST

NU

● INSTALLATION un the e.

INPUTTING POWER

Remove the lens cap.

Engage the power. (Use the adapter provided with this product.) The rated input voltage for this product is AC 24 V, 50/60 Hz. - This device is not fi tted with a power switch. The device

must be provided with power to turn it

- After checking the label on the cable on the right side of the camera, connect the output cable of the provided adapter.

1. 2. 3.

Installation

When the resistance value of copper wire is at [20℃ (68℃)]

Copper wire size (AWG) #24(0.222

) #22(0.332 ) #20(0.522 ) #18(0.832 ) Resistance Ω/m 0.078 0.050 0.030 0.018 Voltage Drop(V/m) 0.028 0.018 0.011 0.006

* Deviations may occur depending on the type of power cable shown in the chart above, and on the wiring manufacturer.

A 22-18 gauge power wire is recommended for this camera.

Voltage reinforcement will occur based on the length of the power wire. If the adapter output wire is too long, camera performance may suffer.

Standard voltage for camera operation: AC24V±10%

Operating the heater in a low temperature costs you a lot of power consumption. Insuffi cient power can cause a product failure. So use only the power outlet with rated AC24V 2.5A.

M

  

STARTUP

The START screen will appear after the power has been turned on.

After completion of initialization, thermal images will be displayed. (within 30 seconds in room temperature)

1. 2.

The sensor will not operate properly immediately after the power is turned on, or when switching between NARROW and WIDE ranges. As a result, thermal images will not display consistently for several seconds. Menu controls can be used to save values to be applied at subsequent start-up of the SCB-9060/9080.

Refer to the owner’s manual for each device. Connection methods employed may differ depending on the monitors and peripheral devices used.

Before connecting devices, ensure their power is turned off.

Adjust the 75Ω/Hi-Z conversion switch for each device based on the following illustration. Select “Hi-Z” for intermediate video receivers and “75Ω” for end equipment. y

y y

MONITOR/COMMUNICATIONS CONNECTION

Connecting the Monitor

Connect the video output terminal on the rear of this product to the monitor.



IR camera Monitor

camera Intermediate video receiver End equipment

RS485 Communications Controls

Using RS485 communications, function settings menus can be adjusted using the Samsung Techwin DVR or System controller.

(1) Controlling menus using a PC

Using an RS485 converter, connect the camera's RS485 control terminal to a serial cable. Example) PC serial board (COM1) → serial cable → RS485 converter → camera RS485 control

terminal

(2) Controlling menus using a DVR system controller

Connect an RS485 cable (TRX+, TRX-) to an RS485 control board connection terminal



MO

ST

● INSTALLATION ffer nt. g

External communications cable RS485 control terminal

(+) CONNECTION TERMINAL (TRX+) 485+

(-) CONNECTION TERMINAL (TRX-)

485-MONITORING GUIDELINES

After thermal images appear, the camera will begin to monitor its range of coverage. 1. Do not adjust the focus if there is no particular point of focus to monitor.

2. For an in-depth explanation of the controls used with the SCB-9060/9080, refer to the section detailing how the camera is operated on page 18.

During monitoring, the SCB-9050/9051 will capture heat sources and display the resulting images on the monitor.

1. In a severe change of the ambient temperature during the monitoring, set the mode to Auto and set the interval to less than 5 minutes in the NUC menu setup.

2. Always carry out an NUC whenever sunlight or high temperature objects are within the fi eld of view.

4. When the camera is used continuously for a long period of time, pay attention to the buildup of dirt on the lens. A dirty lens may result in phenomena such as shortened detection distances.

5. Even if the same item is being monitored, changes in environmental conditions such as rain and fog will affect detection distance. While operating the camera be aware of how such changes may infl uence detection distance.

6. During the monitoring, make sure to comply with the use guidelines mentioned above. 7. If the camera gets dusty, use a soft cloth to wipe off the dust.

STORAGE

Attach the lens cap before storing this device.

Ensure that the storage area is kept within the allowable temperature range listed in this device’s product specifi cations. Do not place this device in a location where condensation may occur.



MENU CONFIGURATION

Main Menu

SYSTEM

● COMM ● RANGE ● UNIT

● TV TYPE ● LANGUAGE ● INFO

● RESET ● RETURN

NUC ● MODE ● INSTANT NUC ● RETURN

ALARM ● TEMP AREA ● TYPE ● ALARM OUT

● DATA ● RETURN

IMAGE

● CONTRAST ● SHARPNESS ● BRIGHTNESS

● AE MODE ● SSNR ● DZOOM

● ROTATION ● RETURN

COLOR ● PALLET ● ISOTHERM ● RETURN

DISPLAY

● CAMERA ID ● DZOOM MAG ● INDICATOR

● POINTER ● TEMP AREA ● ISOTHERM

● RETURN

EXIT

FUNCTION SETTINGS METHODS

Use the Function Setup switch within the camera.

● SETUP MAIN MENU ► SYSTEM NUC ALARM IMAGE COLOR DISPLAY EXIT Select the function using the Function Setup switch.

Main setup menu is displayed on the monitor screen. Select a desired function using the Function Setup switch.

Press the Function Setup switch to move the cursor (arrow) in a desired position. Move the cursor to a desired item.

Select a desired function using the Function Setup switch.

Press the Function Setup switch to display the selected values or status one after another. To exit the menu, select “EXIT” and press the Function Setup switch.

Use the Function Setup switch for a mode item with the arrow mark next to it. You can move to a sub menu item in such a way.

SYSTEM

You can configure the preference settings. When the SETUP menu screen is displayed, select ‘LENS’ by using the Function Setup switch so that the arrow indicates ‘SYSTEM’. Press the Function Setup switch to move to the sub menu items as shown.

COMM : Confi gure the communication settings for the camera. PROTOCOL : Select a communication pro-tocol for the camera; the default propro-tocol is SAMSUNG-T. (SAMSUNG-T, SAMSUNG-E, PELCO-D, PELCO-P, BOSCH, HONEY-WELL, VICON, PANASONIC, GE, AD) Camera ID: Select an ID number between y 2. y 3. y

I

Baud Rate : Select one from 2400/4800/9600/ 19200/38400/57600/115200. (Default : 9600bps)

COMM. MODE : Select a parity bit from NONE/EVEN/ODD. (Default: 8-N-1) Return Packet: Specify the return packet.

Terminal: Specify the termination resistor for RS485 communications. RETURN : Save your settings and return to the SYSTEM menu.

TEMP RANGE : Specify the temperature range for the incoming video signal. You can select NARROW or WIDE according to the temperature range. AUTO : If you select Auto, the mode will switch between NARROW and WIDE automatically according to the ambient temperature.

NARROW : Activated in a temperature range of between -40 and 150. WIDE : Activated in a temperature range of between 0 and 500.

TEMP UNIT : Set the temperature unit to ℃ or ℃ to your preference.

TV TYPE : Specify the video output type. Select NTSC or PAL as appropriate to your area.

If the TV Type is changed, the camera will perform MENU RESET to reset itself.

LANGUAGE : Select one from English, Korean, German, Spanish, Italian, Chinese, Russian, Polish, Japanese, French, Turkish, Czech, Portuguese, Rumanian, Serbian, Taiwanese, Danish, Swedish, Thai.

INFO : Display the operation status and software version.

TV TYPE : Current TV type PROTOCOL : Current protocol CAMERA ID : ID of the current camera BAUDRATE : Current baud rate PARITY : Current parity bit settings VERSION : S/W version of the camera UFPA NO. : Unique data code for each

product SERIAL NO. :Serial number

RESET : Return the menu settings to the factory default. -y -y y y y -y INFO TV TYPE [NTSC] PROTOCOL [SAMSUNG-T] CAMERA ID [001] BAUDRATE [9600] PARITY [NONE] VERSION [X.XX_XXXXXX] UFPA NO. [m0430071] SERIAL NO. [ ]

● SETUP u ge. E o ese, ] ] ] ] ] ] ] ]

NUC

NUC (Non-uniformity Correction) regulates different characteristics of the screen pixels, which results in reproduction of a sharper and clearer image.

When the SETUP menu screen is displayed, select ‘LENS’ by using the Function Setup switch so that the arrow indicates ‘NUC’. Press the Function Setup switch to move to the sub menu items as shown.

MODE : Select an operation mode. AUTO: Operate automatically. ÿINTERVAL: Specify the NUC operation

interval by 1 minute. MANUAL: You can manipulate a desired

operation manually.

INSTANT NUC : Activate NUC.

RETURN : Save your NUC settings and return to the main menu screen.

ALARM

You can specify a specific temperature for detecting a temperature change and tripping an alarm.

When the SETUP menu screen is displayed, select ‘LENS’ by using the Function Setup switch so that the arrow indicates ‘ALARM’. Press the Function Setup switch to move to the sub menu items as shown.

TEMP. AREA : You can specify a total of 8 areas, for each of which you can specify the position and temperature.

SET: If you set SET to ON, you can defi ne the temperature area.

TOP/BOTTOM/LEFT/RIGHT: Navigate through the temperature area in all directions. THRESHOLD: Specify the upper and lower

1. 2. y -y y 1. 2. y -MAIN MENU SYSTEM ► NUC ALARM ALARM ► TEMP AREA 1 TYPE AREA ALARM OUT ON DATA AVR RETURN AUTO ► INTERVAL 00H 10M RETURN TEMP. AREA1 ► SET TOP 64 BOTTOM 178 LEFT 104 RIGHT 200 THRESHOLD HIGH 100℃ LOW 0℃

TYPE : Specify the display of temperature area to either LINE or AREA.

ALARM OUT : Set “ALARM OUT” to “ON/OFF”. If a target appears between the upper and lower limits for tripping the alarm in each area, the alarm will be activated.

DATA : Set the output data from the temperature area to: Average (AVG), Minimum (MIN) and Maximum (MAX).

RETURN : Save your alarm settings and return to the main menu screen.

IMAGE

You can adjust the image settings to your preference. When the SETUP menu screen is displayed, select ‘LENS’ by using the Function Setup switch so that the arrow indicates ‘IMAGE’. Press the Function Setup switch to move to the sub menu items as shown.

CONTRAST : Adjust the contrast level to between 1 and 32.

SHARPNESS : Adjust the sharpness level to between 1 and 32.

BRIGHTNESS : Adjust the brightness level to between 1 and 32.

AE MODE

BYPASS: Do not adjust the contrast and brightness levels, and output the incoming brightness level as it is.

MIN/MAX: In normal conditions, correct the minimum and maximum values of

brightness for an incoming source to optimize the contrast and brightness. WEIGHT: If an incoming source shows a great difference in brightness, this

function optimizes the contrast and brightness to prevent too dark or too bright image.

SSNR : Reduce the background noise for a low contrast image. OFF : Do not activate SSNR.

LOW : Reduce the noise less but no afterimage remains.

MID : Normally accepted mode. Reduce the noise as appropriate with less after image. y y y y 1. 2. y y y y -y -MAIN MENU SYSTEM NUC ALARM ► IMAGE COLOR IMAGE ► CONTRAST 16 SHARPNESS 16 BRIGHTNESS 16 AE MODE MIN/MAX SSNR MID DZOOM OFF ROTATION OFF RETURN

● SETUP he k or age. 16 16 16 AX ID FF FF

DZOOM : Confi gure the digital zoom settings for the camera.

You can set the zoom factor to up to x4. You can move to a sub menu item and change the zoom factor or zooming area to your preference.

ROTATION : Flip or rotate the image.

RETURN : Save your image settings and return to the main menu screen.

COLOR

Configure the color settings for the temperature indication. When the SETUP menu screen is displayed, select ‘LENS’ by using the Function Setup switch so that the arrow indicates ‘COLOR’. Press the Function Setup switch to move to the sub menu items as shown.

PALLET : Specify the color for each specifi c temperature.

BW : White indicates an area with a high temperature while black indicates a low-temp area.

WB : Black indicates an area with a high temperature while white indicates a low-temp area.

COLOR1 : White and yellow indicate an area with a high temperature while black and green indicate a low-temp area. COLOR2 : Indicate the temperature specifi cally using three colors: red, yellow and green.

ISOTHERM : You can specify the temperature threshold by between -40 and 500 degrees. Only a temperature exceeding the threshold will be displayed in the specifi ed color.

RETURN : Save your color settings and return to the main menu screen.

y y y 1. 2. y -y y MAIN MENU SYSTEM NUC ALARM IMAGE ► COLOR DISPLAY COLOR ► PALLET BW ISOTHERM OFF RETURN ISOTHERM ► THRESHOLD 0 °C RETURN

DISPLAY

You can configure the OSD (On Screen Display) settings to your preference. When the SETUP menu screen is displayed,

select ‘LENS’ by using the Function Setup switch so that the arrow indicates ‘DISPLAY’. Press the Function Setup switch to move to the sub menu items as shown.

CAMERA ID : Specify the display of the camera ID.

DZOOM MAG : Specify the display of the digital zoom factor.

INDICATOR : Specify the display of the color bar.

POINTER : Specify the display of the pointer and its position.

TEMP AREA : Specify the display of the temperature area and the display type.

ISOTHERM : Specify the display of the threshold values that are defi ned in the ISOTHERM menu.

RETURN : Save your OSD settings and return to the main menu screen.

EXIT

Exit the Function Setup menu.

1. 2. y y y y y y y MAIN MENU SYSTEM NUC ALARM IMAGE COLOR ► DISPLAY EXIT DISPLAY ► CAMERA ID OFF

DZOOM MAG OFF

INDICATOR ON

POINTER ON

TEMP AREA OFF

ISOTHERM OFF

● SETUP OFF FF ON FF FF

Factory Default

Functions Set Value

RANGE AUTO

UNIT ℃

NUC MODE AUTO

INTERVAL 10M

ALARM

TEMP AREA 1~8(OFF)

TYPE AREA

ALARM OUT OFF THRESHOLD HIGH : 100℃ LOW : 0 ℃

IMAGE CONTRAST 16 SHARPNESS 16 BRIGHTNESS 16 AE MODE MIN/MAX SSNR MID DZOOM OFF ROTATION OFF CLOLR PALETTE BW ISOTHERM OFF DISPLAY CAMERA ID OFF DZOOM MAG OFF INDICATOR OFF

POINTER OFF

TEMP AREA OFF

ISOTHERM OFF RS485 PROTOCOL: SAMSUNG-T CAMERA ID:1 BAUDRATE:9600 UART MODE: 8-N-1 RET PKT：ENABLE TERMINATION：OFF LANGUAGE ENGLISH

SP

TROUBLESHOOTING

Check the points listed below if the product appears to be malfunctioning. If the problem continues, please contact the sales agent from whom the product was purchased.

PROBLEM SOLUTION

If nothing can be seen onscreen

▶ Verify that the power source is connected properly, and that the device is receiving power.

▶ Verify that the video signal wire is connected properly.

If screen images do not appear clearly

▶ Wipe the lens with a clean cloth or brush to remove any dust that may be present.

▶ Adjust the status of the monitor.

▶ Change the position or angle of the camera if a large amount of bright light is displayed onscreen.

If the screen is too dark

▶ Adjust the status of the monitor

▶ Verify that intermediate processing can be performed properly between systems.

If the camera is operating abnormally, or its surface is very hot, causing black lines to appear onscreen :

▶ Verify that the power voltage received by the camera conforms to the proper rating. Also, confi rm whether performance is affected by the time of day.

If RS485 communications cannot be carried out

▶ Verify the polarity of the RS485 communications terminal and the arrangement of the cables.

▶ Verify the RS485 communications settings.

※ RS485 Communication Settings Default Values Item Camera No. Communications

Speed

Communications Mode

Data Reception

● SPECIFICATIONS

SPECIFICATIONS

Imaging Device 320(H)x240(H) Uncooled Microbolometer

Sensor Pitch 23.5μm

Measured wavelength

range 8 ~ 14um, LWIR

Video Ratio ( Sensor ) 30fps 25fps 30fps 25fps

Thermal Sensitivity(NETD) <80mK @ F1.0

Video Output CVBS 1.0 Vp-p / 75 composite, ITU-656 8bit Digital Output Lens Type

Focal Length (Zoom Ratio) 14mm ( Fixed ) 50mm ( Fixed )

Max. Aperture Ratio 1:1.4

Angular Field of View ( H×V ) 30° x 22.8° 8.6° x 6.5°

Min. Object Distance 3m ~ ∞, Pan focus 27m ~∞, Pan focus IFOV (Instaneous Field of

View) 1.68mrad 0.47mrad

Focus Control Manual

Operational On Screen Display

Multi Language OSD (19 Languages)

E/F/G/S/I/RUS/P/TUR/POR/K/J/TAIWAN/SER/ROM/SWE/DAN/ C/TAI/CZE

NUC(Non-Uniformity

Correction) Auto/Manual Selectable

Temperature Range -40°C ~ +500°C

Digital AE Bypass, Min/Max, Weight Mode Selectable

Brightness 32 Steps Adjustable

Sharpness 32 Steps Adjustable

Contrast 32 Steps Adjustable

DNR(Digital Noise _{2D/3D Adaptive DNR, Off/Low/Middle/High Selectable}

Specifications

SCB-9060N SCB-9060P SCB-9080N SCB-9080P

Temperature Display Area Adjustable 8 Zone & Position Movable Cross Point

ISOTherm Isolated Temperature Display

Pseudo Color B/W, W/B, Color1, Color2 Selectable Temp Indicator Min/Max Scene Temperature with Color Bar

Alarm Temperature Detection, 1 GPIO Alarm Output

Communication RS-485, Coax(Pelco Coaxitron Compatible)

Protocol SAMSUNG-T, SAMSUNG-E, PELCO-D, PELCO-P, BOSCH,

HONEYWELL, VICON, PANASONIC, GE, AD Environmental

Operating Temperature /

Humidity -30°C ~ +55°C / Less than 90% RH

Ingress Protection IP66

RoHS Compliant Yes

Electrical

Input Voltage/Current 24VAC±10%

Power Consumption Max. 30W

Mechanical

Color / Material Body : Ivory, Aluminum

Dimension (WxHxD) 104×123x301mm 104×123x318mm

Weight 1.6Kg 1.8Kg

※ This specifi cation can be changed without notice for performance improvement of product.

● SPECIFICATIONS P ct.

DIMENSION

Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60, FAX : +82-31-8018-3745

SAMSUNG TECHWIN EUROPE LTD.

Samsung House, 1000 Hillswood Drive, Hillswood Business Park

SAMSUNG TECHWIN AMERICA Inc.