Product Information/Specifications

(1)

RECOMMENDED USES:

Smooth or rough sawn exterior vertical wood

surfaces such as plywood, fences, shingles,

shakes, siding. laminates, masonry and stucco

surfaces.

BEHR®

BARN & FENCE

PAINT

NO. 25

BARN RED

AVAILABLE IN: Gallon Only

COLORS

No. 25 Barn Red* *Stock Color

TINT BASE / MAX TINT*

No. 25 – 128 oz. *NOT TINTABLE

FINISH

Flat. Sheen Level 10.0 – 20.0 @ 85º

*Substrate Dependant

COVERAGE RATE

Smooth Surfaces

First Coat - 400 sq. ft. per gallon Second Coat – 500 sq. ft. per gallon

Rough Surfaces

First Coat – 200

sq. ft. per gallon Second Coat – 250 sq. ft. per gallon 4 mils wet, 1.40 mil dry

DRYING TIME

@77°F & 50% humidity*

*Longer dry time required in cooler temperatures or in higher humidity. To Touch: 2-3 Hours

Recoat: 6-8 Hours

PRIMERS

No. 434 Int./Ext. Oil-Based Primer No. 436 Exterior Water Based Primer

COMPOSITION

Vehicle/Active Ingredient:

Alkyd / Acrylic

Percent Solids By Volume:

37%

Percent Solids By Weight:

47.5%

Weight Per Gallon:

10.0 1bs.

VOC

<98 g/l

Flashpoint

N/A

MSDS

Available @ www.behr.com Or 1-800-854-0133 Ext. 2

Clean Up

Soap & Water. Recycle or dispose of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org

APPLICATION TOOLS

Airless Spray: Filter: 60 mesh Tip: .015-.017

Conventional Spray: See manufacturer

recommendations

Brush: Nylon/Polyester blend

Roller: 3/8”-3/4” Nap. Depending on texture.

Thinner: Do Not Thin.

SURFACE PREPARATION

New or Weathered Surfaces: Remove mill

glaze, loose wood fibers and deteriorated latex or oil-based finishes with BEHR No 64 15 Minute Quik-Fix® Deck Finish Remover & Wood Resurfacer. Rinse. Remove mildew with BEHR No. 62 Multi-Surface Deck-Prep™ Cleaner & Mildew Stain Remover or bleach and water. Rinse Follow the steps above with BEHR No. 63 Cleaner, Brightener Conditioner to open wood grain, neutralize and rejuvenate the natural color of the wood. Rinse thoroughly Previously

Coated: - Previously coated surfaces in good

condition should be thoroughly cleaned before re-coating. Use No. 62 & No 63 as listed above.

APPLICATION

Do not use if temperature is below 50ºF or if rain is expected within 24 hours. Intermix multiple containers to ensure color and sheen uniformity. Applying 2 coats will provide maximum

performance and added protection. Airless spray is recommended for experienced applicators only. This information is believed to be reliable; however Behr Process

Corporation makes no warranty, guarantee, or representation and assumes no liability as to the absolute correctness or sufficiency of the specifications.

(2)

RECOMMENDED USES:

Smooth or rough sawn exterior vertical wood

surfaces such as plywood, fences, shingles,

shakes, siding. laminates, masonry and stucco

surfaces.

BEHR®

BARN & FENCE

PAINT NO. 35

HIGH HIDE WHITE

AVAILABLE IN: Gallon Only

COLORS

No. 35 High Hide White* *Stock Color

TINT BASE / MAX TINT*

No. 35 – 128 oz. *NOT TINTABLE

FINISH

Flat Sheen Level 10.0-20.0 @ 85º*

*Substrate Dependant

COVERAGE RATE

Smooth Surfaces

First Coat - 400 sq. ft. per gallon Second Coat – 500 sq. ft. per gallon

Rough Surfaces

First Coat – 200

sq. ft. per gallon Second Coat – 250 sq. ft. per gallon 4 mils wet, 1.40 mil dry

DRYING TIME

Recoat: 6-8 Hours

PRIMERS

No. 434 Int./Ext. Oil-Based Primer No. 436 Exterior Water Based Primer

COMPOSITION

Alkyd / Acrylic

35%

51%

11.2 1bs.

VOC

<96 g/l

Flashpoint

N/A

MSDS

Clean Up

APPLICATION TOOLS

recommendations

Roller: 3/8”-3/4” Nap. Depending on texture.

SURFACE PREPARATION

New or Weathered Surfaces: Remove mill

glaze, loose wood fibers and deteriorated latex or oil-based finishes with BEHR No 64 15 Minute Quik-Fix® Deck Finish Remover & Wood Resurfacer. Rinse. Remove mildew with BEHR No. 62 Multi-Surface Deck-Prep™ Cleaner & Mildew Stain Remover or bleach and water. Rinse Follow the steps above with BEHR No. 63 Cleaner, Brightener Conditioner to open wood grain, neutralize and rejuvenate the natural color of the wood. Rinse thoroughly Previously

Coated: - Previously coated surfaces in good

condition should be thoroughly cleaned before re-coating. Use No. 62 & No 63 as listed above..

APPLICATION

Do not use if temperature is below 50ºF or if rain is expected within 24 hours. Intermix multiple containers to ensure color and sheen uniformity. Applying 2 coats will provide maximum

performance and added protection. Airless spray is recommended for experienced applicators only. This information is believed to be reliable; however Behr Process

To Consult with a Technical Service Representative call 1-800-854-0133 Ext. 2

(3)

RECOMMENDED USES:

New or old Unglazed Tile, Masonry Shingle, Anchored

Gravel, Aluminum/Metal Materials, Composition Sheets,

Asphalt Shingle, Concrete or Cement Block, Urethane

Foam, Slate or Wood shaken Wood shake Roofs. It is not

intended to waterproof or repair roof leak. This product is

intended to brighten roofs and reflect heat.

BEHR®

FLAT FINISH ROOF

PAINT

No. 65

WHITE REFLECTIVE

AVAILABLE IN: Gallon & Five Gallon

COLORS

No. 65 White

Tintable Bases/Max Tint

No. 65 – 126 oz. White – 4 oz

Custom colors plus computer color matching

FINISH

Flat. *Sheen Level 0-4.0 @ 85º

*Substrate Dependant

COVERAGE RATE

250 (23m2) sq. ft. per gallon on rough surfaces. 350 (32m2)sq. ft. per gallon for second coat. 350 (32m2) sq. ft. per gallons on smooth surfaces. 450 (42m2) sq. ft. for second coat. 4 mils wet, 1.3 mils dry

DRYING TIME

*Longer dry time may be needed in cooler temperatures or higher humidity.

To Touch: 2 Hours Recoat: 4 Hours Cured: Two Weeks

PRIMERS

No. 436 Exterior Water-Based Primer

No. 434 Oil-Based Primer

COMPOSITION

100% Acrylic

35%

53%

11.8 1bs.

VOC

<250 g/l

Flashpoint

N/A

MSDS

Clean Up

Soap & Water. Recycle or dispose of unused product call 1-800-CLEANUP (U.S.A. only) www.earth911.org

APPLICATION TOOLS

recommendations

Roller: 1” Nap roller. Depending on the surface

texture.

Thinner: Do Not Thin. If spraying only, thin no

more ½ pint of water per gallon

SURFACE PREPARATION

Replace brittle or cracked shingles. Clean all roof surfaces. Previously coated surface should be wire brushed or scraped to remove all loose coating. Remove mildew with BEHR® No. 62 Multi-Surface Deck-Prep™ Cleaner and Mildew Stain Remover or bleach and water. On

galvanized metal, use a diluted solution of BEHR® No. 991 Concrete Etcher & Rust Remover to prepare surface. If applying on wood shake, clean with BEHR® No. 63 Wood Cleaner Brightener Conditioner. Follow directions on products labels. Rinse. Allow to dry for 24 hours. Prime all metal, asphalt and wood surfaces.

APPLICATION

Use product when surface and air temperature are between 50°-90°F. Intermix multiple containers, to ensure color and sheen uniformity. Apply starting at the top of the roof working down. Always maintain a wet edge.

This information is believed to be reliable; however Behr Process Corporation makes no warranty, guarantee, or representation and assumes no liability as to the absolute correctness or sufficiency of the specifications.

(4)

RECOMMENDED USES:

New or old Unglazed Tile, Masonry Shingle, Anchored

Gravel, Aluminum/Metal Materials, Composition Sheets,

Asphalt Shingle, Concrete or Cement Block, Urethane

Foam, Slate or Wood shaken Wood shake Roofs. It is not

intended to waterproof or repair roof leak. This product is

intended to brighten roofs and reflect heat.

BEHR®

FLAT FINISH ROOF

PAINT

No. 66

DEEP BASE

AVAILABLE IN: Gallon & Five Gallon

COLORS

No. 66 Deep Base

Tintable Bases/Max Tint

No. 66 – 116 oz. Deep Base – 14 oz

Custom colors plus computer color matching

FINISH

Flat. *Sheen Level 0-4.0 @ 85º

*Substrate Dependant

COVERAGE RATE

250 (23m2) sq. ft. per gallon on rough surfaces. 350 (32m2)sq. ft. per gallon for second coat. 350 (32m2) sq. ft. per gallons on smooth surfaces. 450 (42m2) sq. ft. for second coat. 4 mils wet, 1.3 mils dry

DRYING TIME

*Longer dry time may be needed in cooler temperatures or higher humidity.

To Touch: 2 Hours Recoat: 4 Hours Cured: Two Weeks

PRIMERS

No. 436 Exterior Water-Based Primer

No. 434 Oil-Based Primer

COMPOSITION

100% Acrylic

31%

44%

11.8 1bs.

VOC

17gm/l Material (Includes Water) 50 gm/l Coating (Excludes Water)

Flashpoint

N/A

MSDS

Clean Up

Soap & Water. Recycle or dispose of unused product call 1-800-CLEANUP (U.S.A. only) www.earth911.org

APPLICATION TOOLS

recommendations

Roller: 1” Nap roller. Depending on the surface

texture.

more ½ pint of water per gallon

SURFACE PREPARATION

Replace brittle or cracked shingles. Clean all roof surfaces. Previously coated surface should be wire brushed or scraped to remove all loose coating. Remove mildew with BEHR® No. 62 Multi-Surface Deck-Prep™ Cleaner and Mildew Stain Remover or bleach and water. On

galvanized metal, use a diluted solution of BEHR® No. 991 Concrete Etcher & Rust Remover to prepare surface. If applying on wood shake, clean with BEHR® No. 63 Wood Cleaner Brightener Conditioner. Follow directions on products labels. Rinse. Allow to dry for 24 hours. Prime all metal, asphalt and wood surfaces.

APPLICATION

Use product when surface and air temperature are between 50°-90°F. Intermix multiple containers, to ensure color and sheen uniformity. Apply starting at the top of the roof working down. Always maintain a wet edge.

(5)

BEHR® ELASTOMERIC

MASONRY, STUCCO

&BRICK PAINT

NO. 68

WHITE

RECOMMENDED USES:

Excellent adhesion on new or previously

painted exterior vertical surfaces made of

stucco, masonry, concrete, concrete block,

cement, adjacent or metal trims.

AVAILABLE IN: Gallon & Five Gallon

COLORS

No. 68 White

Custom colors plus computer color matching available.

TINT BASE / MAX TINT*

No. 68 – 120 oz. White – 8 oz.

FINISH

Flat *Sheen Level 3.5-5.5 @85º

*Substrate Dependant

COVERAGE RATE

75-125 sq. ft. per gallon 10 mils wet, 5 mils dry

DRYING TIME

Recoat: 24 Hours Cured: 30 Days

PRIMERS

No. 436 Exterior Water Based Primer

COMPOSITION

100% Acrylic

48%

60%

10.8 1bs.

VOC

Flashpoint

N/A

MSDS

Clean Up

APPLICATION TOOLS

Conventional Spray: N/A

Roller: 1 1/4” Nap.

SURFACE PREPARATION

Remove all loose, peeling paint using a scraper or sandpaper. Wash off all chalk, dirt, grease, soap and oil-build-up with mild detergent; remove mildew with BEHR No. 62 Multi-Surface Deck-Prep™ Cleaner & Mildew Stain Remover or bleach and water. Rinse and allow to dry. Cracks and gaps wider than 1/16” should be routed open, dusted, primed and packed with an elastomeric patching compound prior to product application. Scuff sand glossy surfaces before priming. Prime all chalky, glossy or bare surfaces with BEHR Exterior 100% Acrylic Latex Primer & Sealer.

APPLICATION

Use product when surface and air temperature are between 50º- 90ºF. Intermix multiple containers to ensure color and sheen uniformity. Apply one coat of about 10 mils wet film thickness. After 24 hours, a second coat of 10 mils wet film thickness must be applied. A third coat may be required to achieve a final dry mil thickness of about 10-15 mils. Airless Spray: Tip size and atomization pressure will vary depending upon specific equipment used, the viscosity of the coating and temperatures at the time of application..

(6)

BEHR® INT/EXT

MASONRY, STUCCO

& BRICK FLAT

PAINT

NO. 270 WHITE

RECOMMENDED USES:

Great for new or old, previously coated

interior or exterior vertical surfaces such as

brick, masonry, stucco, concrete, cement,

slate, stone, cinder block, adobe and clay.

AVAILABLE IN: Gallon & Five Gallon

COLORS

No. 270 White

TINT BASE / MAX TINT*

No. 270 – 126 oz. White – 4 oz.

FINISH

Flat *Sheen Level 0 - 3.5 @85º

*Substrate Dependant

COVERAGE RATE

Rough: 250-300 sq. ft. per gallon Smooth: up to 400 sq. ft. per gallon 4 mils wet, 1.20 mils dry

DRYING TIME

Recoat: 4 Hours Cured: Two Weeks

PRIMERS

COMPOSITION

Acrylic Latex

31%

46%

10.8 1bs.

VOC

Flashpoint

N/A

MSDS

Clean Up

APPLICATION TOOLS

recommendations

Roller: ¾” - 1” Nap. Depending on the surface

texture.

more than ½ pint of water per gallon.

SURFACE PREPARATION

Remove all loose, peeling paint using a scraper or sandpaper. Wash off all chalk, dirt, grease, soap and oil-build-up with mild detergent; remove mildew with BEHR No. 62 Multi-Surface Deck-Prep™ Cleaner & Mildew Stain Remover or bleach and water. Rinse and allow to dry. Scuff sand glossy surfaces. Patch holes and cracks. Caulk joints and seams.

APPLICATION

Use product when surface and air temperature are between 50º- 90ºF. Intermix multiple containers to ensure color and sheen uniformity. Certain colors may require multiple coats. Apply using a high quality roller cover, nylon/polyester brush or airless sprayer.

(7)

BEHR® INT/EXT

MASONRY, STUCCO

& BRICK FLAT

PAINT

NO. 271

PASTEL BASE

RECOMMENDED USES:

Great for new or old, previously coated

interior or exterior vertical surfaces such as

brick, masonry, stucco, concrete, cement,

slate, stone, cinder block, adobe and clay.

AVAILABLE IN: Gallon & Five Gallon

COLORS

No. 271 Pastel Base

TINT BASE / MAX TINT*

No. 271 – 120 oz. Pastel Base – 8 oz.

FINISH

Flat

*Sheen Level 0 - 3.5 @85º

*Substrate Dependant

COVERAGE RATE

DRYING TIME

PRIMERS

COMPOSITION

Acrylic Latex

33%

47%

10.6 1bs.

VOC

Flashpoint

N/A

MSDS

Clean Up

APPLICATION TOOLS

recommendations

texture.

SURFACE PREPARATION

APPLICATION

(8)

BEHR® INT/EXT

MASONRY, STUCCO &

BRICK SATIN PAINT

NO. 280 WHITE

RECOMMENDED USES:

Great for new or old, previously coated

interior or exterior vertical surfaces such as

brick, masonry, stucco, concrete, cement,

slate, stone, cinder block, adobe and clay.

AVAILABLE IN: Gallon & Five Gallon

COLORS

No. 280 White

TINT BASE / MAX TINT*

No. 280 – 126 oz. White – 4 oz.

FINISH

Satin *Gloss Level 15.0-25.0 @ 60º Sheen Level 35.0-45.0 @85º

*Substrate Dependant

COVERAGE RATE

DRYING TIME

PRIMERS

COMPOSITION

Acrylic Latex

32.5%

43.5%

10.1 1bs.

VOC

Flashpoint

N/A

MSDS

Clean Up

APPLICATION TOOLS

recommendations

texture.

SURFACE PREPARATION

APPLICATION

(9)

BEHR® INT/EXT

MASONRY, STUCCO &

BRICK SATIN PAINT

NO. 2-280 WHITE

RECOMMENDED USES:

Great for new or old, previously coated

interior or exterior vertical surfaces such as

brick, masonry, stucco, concrete, cement,

slate, stone, cinder block, adobe and clay.

AVAILABLE IN: Gallon & Five Gallon

COLORS

No. 2-280 White

TINT BASE / MAX TINT*

No. 2-280 – 126 oz. White – 4 oz.

FINISH

*Substrate Dependant

COVERAGE RATE

DRYING TIME

PRIMERS

COMPOSITION

Acrylic Latex

33%

44%

10.03 1bs.

VOC

<50 gm/l

Flashpoint

N/A

MSDS

Clean Up

APPLICATION TOOLS

recommendations

texture.

SURFACE PREPARATION

APPLICATION

(10)

BEHR® INT/EXT

MASONRY, STUCCO &

BRICK SATIN PAINT

NO. 281

PASTEL BASE

RECOMMENDED USES:

Great for new or old, previously coated

interior or exterior vertical surfaces such as

brick, masonry, stucco, concrete, cement,

slate, stone, cinder block, adobe and clay.

AVAILABLE IN: Gallon & Five Gallon

COLORS

No. 281 Pastel Base

TINT BASE / MAX TINT*

No. 281 – 118 oz. Pastel Base – 12 oz.

FINISH

*Substrate Dependant

COVERAGE RATE

DRYING TIME

PRIMERS

COMPOSITION

Acrylic Latex

32%

41%

9.6 1bs.

VOC

Flashpoint

N/A

MSDS

Clean Up

APPLICATION TOOLS

recommendations

texture.

SURFACE PREPARATION

APPLICATION

(11)

BEHR® INT/EXT

MASONRY, STUCCO &

BRICK SATIN PAINT

NO. 2-281

PASTEL BASE

RECOMMENDED USES:

Great for new or old, previously coated

interior or exterior vertical surfaces such as

brick, masonry, stucco, concrete, cement,

slate, stone, cinder block, adobe and clay.

AVAILABLE IN: Gallon & Five Gallon

COLORS

No. 2-281 Pastel Base

TINT BASE / MAX TINT*

No. 2-281 – 118 oz. Pastel Base – 12 oz.

FINISH

*Substrate Dependant

COVERAGE RATE

DRYING TIME

PRIMERS

COMPOSITION

Acrylic Latex

32%

41%

9.6 1bs.

VOC

<50 gm/l

Flashpoint

N/A

MSDS

Clean Up

APPLICATION TOOLS

recommendations

texture.

SURFACE PREPARATION

APPLICATION

(12)

RECOMMENDED USES:

hydrostatic pressure. Ideal for above or below grade

Walls, Retaining Walls, Garage Walls, Masonry

Walls, Cinder Blocks, Stucco, Brick, Foundations

and Landscape Walls. Apply to dry or slightly damp

surfaces. Not for use on floors or walls with active

water leaks.

BEHR®

INTERIOR/EXTERIOR

CONCRETE & MASONRY

WATERPROOFING PAINT

No. 870 WHITE

AVAILABLE IN: Gallon & Five Gallon

COLORS

No. 870 White

Tintable Bases/Max Tint

No. 870 White – 126 oz White - 4oz

FINISH

Flat. *Gloss Level <5% @ 60º

*Substrate Dependant

COVERAGE RATE

On rough porous masonry, 75–100 sq. ft. (7-9m2) per gallon. On smoother surfaces, 100–125 sq. ft. (9-12m2) per gallon.

13 mils wet, 6 mils dry

DRYING TIME

@77°F(25°C) and 50% humidity* *Longer dry time required in cooler temperatures and in higher

humidity. To Touch: 1 Hour Recoat: 4 Hours Full Cure: 7-14 Days

PRIMERS

N/A

COMPOSITION

Acrylic

44%

60%

11.7 1bs.

VOC

123 g/l Material (includes water) 219 g/l Coatings (includes water)

Flashpoint

N/A

MSDS

Clean Up

Use soap and water. Properly dispose of all soiled rags and protect unused product from freezing. To recycle or properly dispose of paint in your community call 1-800-CLEANUP or visit www.Earth911.org.

SURFACE

PREPARATION

New or Unpainted Surfaces:

New concrete must cure for a minimum of 30 days. Test for loose, flaking concrete by pressing a piece of masking or cellophane tape at various places, then pull it off with an abrupt action. If the tape does not pull the concrete from the surface, it can be painted. If the existing concrete is removed, the loose concrete should be removed down to a sound substrate. All holes or cracks must be properly patched with fast setting hydraulic cement. Remove mildew stains with BEHR® No. 62 Premium Mildew Stain Remover. Follow all label instructions. All surfaces must be clean and free of dirt, dust, efflorescence and oil. Clean surface with BEHR No. 991 Concrete & Masonry Cleaner/Etcher. Follow all label instructions.

APPLICATION TOOLS

Airless Spray: Filter: Remove Tip: .023-.025

Fluid pressure: 2,200-3,200 psi

Conventional Spray: N/A Brush: Nylon/Polyester Blend

Roller: 3/8" to 3/4" Nap. Depending on the

surface texture.

SURFACE PREPARATION Con’d

Previously Painted Surfaces:

BEHR No. 870 Concrete & Masonry Waterproofing Paint provides best results when applied to bare or untreated surfaces. Previously Painted Surfaces In Good, Repaintable Condition May Be Painted With Behr No. 870, However, Behr Will Not Guarantee The Results. Test for loose, flaking paint by pressing a piece of masking or cellophane tape at various places, then pull it off with an abrupt action. If the tape does not pull the paint from the surface, it can be painted. If the existing paint is removed, the loose paint should be removed down to a sound substrate by wire brushing or sanding. For Interior or Exterior application; remove deteriorated coating prior to application. Follow all label instructions. Follow all preparation instructions under “New or Unpainted Surfaces” above.

APPLICATION

Stir well before use. Do not thin product. Use with adequate ventilation. Use product when the surface and air temperature are between 50-90ºF (10-32ºC). Apply to dry or slightly damp masonry walls. Wipe off any visible moisture with a dry cloth before painting. Two coats minimum are required: First Coat: Using a brush or roller, work the waterproofer onto the masonry wall surface making certain to cover any pores or voids. Second Coat: Using a brush or roller, cover the entire surface. Properly fill any voids left after the first coat. Additional spot application may be needed depending on the porosity of the surface. Important: If leaking is still present after two coats, it indicates that voids or pinholes are still open. Re-apply product to these areas. Do Not Thin product or apply at a greater spread rate. This information is believed to be reliable; however Behr Process

(13)

RECOMMENDED USES:

Use on Interior or

Exterior surfaces such as: Concrete, Masonry, Stucco,

Cinder Block and any Porous Stone or Brick. Not

designed for use on wood, metal or silicone treated

surfaces. Do not use on coated surfaces. Use only on

porous surfaces. Note: Some Surfaces May Appear

Slightly Darker After Product Dries.

BEHR® INT/EXT

CONCRETE

BONDING

PRIMER

No. 880

AVAILABLE IN: Gallon Only

COLORS

No. 880 Milky and dries clear

Tintable Bases/Max Tint

No. 880 – 128 oz. Not Tintable

FINISH

Gloss Sheen Level 15-20 @ 60º

COVERAGE RATE

350-400 sq. ft. (33-37 m2) per gallon depending on texture and porosity.

DRYING TIME

@77°F & 50% humidity. Must apply a topcoat after at least 8 hours, but before 30 days.

To Touch: 2-4 Hours Recoat: 8 Hours

PRIMERS

N/A

COMPOSITION

Vehicle/Active Ingredient: Epoxy

16%

15%

8.6 1bs.

VOC

37 gm/l Material (Includes Water) 187 gm/l Coating (Excludes Water)

Flashpoint

N/A

MSDS

Clean Up

Commercial Brush Cleaner. Recycle or dispose of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org

APPLICATION TOOLS

Airless Spray: Filter: 60 mesh Tip: 015-.017

Conventional Spray: Not Recommended

Brush: Nylon/Polyester blend or Pad Applicator

Roller: 3/8”-1/2” Nap. Depending on the

surface texture.

SURFACE PREPARATION

New concrete must cure for a minimum of 30 days prior to priming. Patch all holes and cracks and allow to dry. For touch-ups where surface coatings have failed, completely remove any loose or peeling paint. Do not apply over previously coated surfaces. Remove all dirt, grease and oil with BEHR® No. 990 Concrete

Cleaner & Degreaser. Refer to product label for specific instructions. Etch dense, smooth

concrete using BEHR No. 991 Concrete Etcher & Rust Remover. Refer to product label for specific instructions.

APPLICATION

DO NOT THIN. Stir paint before and occasionally during application. Use product when air and surface temperatures are between 50-90°F (10-32°C). Initial foaming will disappear upon drying.

(14)

RECOMMENDED USES:

Walls subject to hydrostatic pressure. Ideal for above or

below grade basement walls, retaining walls, masonry

walls, cinder blocks, stucco, brick, foundations and

landscape wall

s.

BEHR®

Basement & Masonry

Waterproofing Paint

No. 875

AVAILABLE IN: Gallon & Five Gallon

COLORS

No. 875 White

Tintable Bases/Max Tint

No. 875 White – 126 oz White Base - 4oz

FINISH

Flat.

*Gloss Level <5% @ 60º

*Substrate Dependant

COVERAGE RATE

DRYING TIME

humidity.

To Touch: 1 Hours Recoat: 4 Hours Full Cure: 7-14 Days

PRIMERS

N/A

COMPOSITION

Acrylic

44%

60%

11.7 1bs.

VOC

123 g/l Material (includes water) 219 g/l Coatings (includes water)

Flashpoint

N/A

MSDS

Clean Up

APPLICATION TOOLS

surface texture.

SURFACE PREPARATION

All surfaces must be clean and free of dirt, dust, efflorescence, oil and previous coatings. Clean surface with BEHR® No. 990 Concrete Cleaner & Degreaser. All holes or cracks must be properly patched with a fast setting hydraulic cement. Eliminate mildew stains with BEHR No. 62 Multi-Surface Deck-Prep Cleaner & Mildew Stain Remover or bleach and water. Remove efflorescence with BEHR No. 991 Concrete Etcher & Rust Remover. For Exterior application; use BEHR No. 64 15 Minute Quik-Fix™ Deck Finish Remover & Wood Resurfacer to remove latex or oil-base finishes. For Interior application; use a chemical stripper designed for interior use. New concrete must be completely cured (minimum 30 days) before application.

APPLICATION

Stir well before use. Do not thin product. Use with adequate ventilation. Use product when the surface and air

temperature are between 50º–90ºF (10º-32ºC). Apply to dry or lightly damp masonry walls. Two coats minimum are required: First Coat: Using a brush, work the waterproofer into the pores of the masonry.

Second Coat: Using a brush, roller or sprayer, cover

the entire surface. Properly fill any voids left after first coat. Additional spot application may be needed depending on the porosity of the surface. Important:

If leaking is still present after two coats, it indicates that voids or pinholes are still open. Reapply product to these areas. Do not under apply. This information is believed to be reliable; however Behr Process

(15)

RECOMMENDED USES:

Walls subject to hydrostatic pressure. Ideal for above or

below grade basement walls, retaining walls, masonry

walls, cinder blocks, stucco, brick, foundations and

landscape wall

s.

BEHR®

Basement & Masonry

Waterproofing Paint

No. 2-875

AVAILABLE IN: Gallon & Five Gallon

COLORS

No. 2-875 White

Tintable Bases/Max Tint

No. 2-875 White – 126 oz White Base - 4oz

FINISH

Flat.

*Gloss Level <5% @ 60º

*Substrate Dependant

COVERAGE RATE

DRYING TIME

humidity.

To Touch: 1 Hours Recoat: 4 Hours Full Cure: 7-14 Days

PRIMERS

N/A

COMPOSITION

Acrylic

44%

60%

11.7 1bs.

VOC

48 g/l Material (includes water) 97 g/l Coating (excludes water)

Flashpoint

N/A

MSDS

Clean Up

APPLICATION TOOLS

surface texture.

SURFACE PREPARATION

All surfaces must be clean and free of dirt, dust, efflorescence, oil and previous coatings. Clean surface with BEHR® No. 990 Concrete Cleaner & Degreaser. All holes or cracks must be properly patched with a fast setting hydraulic cement. Eliminate mildew stains with BEHR No. 62 Multi-Surface Deck-Prep Cleaner & Mildew Stain Remover or bleach and water. Remove efflorescence with BEHR No. 991 Concrete Etcher & Rust Remover. For Exterior application; use BEHR No. 64 15 Minute Quik-Fix™ Deck Finish Remover & Wood Resurfacer to remove latex or oil-base finishes. For Interior application; use a chemical stripper designed for interior use. New concrete must be completely cured (minimum 30 days) before application.

APPLICATION

Stir well before use. Do not thin product. Use with adequate ventilation. Use product when the surface and air

temperature are between 50º–90ºF (10º-32ºC). Apply to dry or lightly damp masonry walls. Two coats minimum are required: First Coat: Using a brush, work the waterproofer into the pores of the masonry.

Second Coat: Using a brush, roller or sprayer, cover

the entire surface. Properly fill any voids left after first coat. Additional spot application may be needed depending on the porosity of the surface. Important:

If leaking is still present after two coats, it indicates that voids or pinholes are still open. Reapply product to these areas. Do not under apply. This information is believed to be reliable; however Behr Process

(16)

AVAILABLE IN: Quart & Gallon

RECOMMENDED USES:

Properly prepared Interior or Exterior

surfaces such as: Wood, Drywall, Plaster,

Masonry, Metal, Well-bonded Wallpaper,

Brick, Stucco, Aluminum and Cinder Block.

Do not use on horizontal surfaces.

BEHR®

INTERIOR/EXTERIOR

OIL-BASED

SEMI-GLOSS ENAMEL

PAINT NO. 3800

ULTRA PURE WHITE

COLORS

No. 3800 - Ultra Pure White

Tintable Bases/Max Tint

No. 3800 - Ultra Pure White Ultra Pure White – 2 oz Over 1600 custom colors plus computer color matching

FINISH

Semi-Gloss *Gloss Level 45 - 55 @ 60º

*Substrate Dependant

COVERAGE RATE

500-550 sq. ft. (46-51 m2) per gallon over primed smooth surfaces and 350-400 sq. ft. (33-37 m2) per gallon over primed rough surfaces.

2.9 mils wet, 1.6 mils dry

DRYING TIME

@77°F & 50% humidity Longer dry time required in cooler temperatures and higher humidity.

To Touch: 4-5 Hours Recoat: 24 Hours Cured: 7 Days

PRIMERS

N0. 436 Acrylic Primer & Sealer No. 434 Oil-Based Primer & Sealer

COMPOSITION

Alkyd Resin

53.4%

72.1%

11.06 1bs.

VOC

370 g/l Material (Including Water) 370 g/l Coating (Excludes Water)

Flashpoint

104°F (40º C)

MSDS

Clean Up

Use mineral spirits. Properly dispose of all soiled rags and protect unused product from freezing. To recycle or properly dispose of paint in your community call 1-800-CLEANUP (U.S.A. only) or visit www.Earth911.org.

APPLICATION TOOLS

Airless Spray: Filter: 60 mesh Tip: .013 - .015

recommendations

Brush: High Quality China Bristle Brush

Roller: 1/4-3/8" Nap. Depending on the surface texture.

SURFACE PREPARATION

Allow new stucco, plaster and masonry to cure for 30 days. CLEAN: For interior and exterior surfaces, remove dirt, oil and grease stains with BEHR® No. 990 Concrete & Masonry Cleaner/Degreaser. To remove mildew stains, use BEHR No. 62 Premium Mildew Stain Remover. Remove all loose and peeling paint; scuff sand glossy surfaces; caulk; repair imperfections and sand smooth. For exterior surfaces, powerwash to remove chalk. Etch galvanized metal with BEHR No. 991 Concrete & Masonry

Cleaner/Etcher. Follow all label instructions. PRIME: Use BEHR N0. 436 100% Acrylic Primer & Sealer or BEHR N0. 434 Oil-Based Primer & Sealer. Follow all label instructions.

APPLICATION

DO NOT THIN. Stir before and during application. When working with more than one can of the same product, intermix to ensure color uniformity. Use adequate ventilation during application & drying process. Certain colors may require more than one coat to achieve complete hide and coverage. Use product when air and surface temperatures are between 40–90°F (4-32°C).

(17)

AVAILABLE IN: Quart & Gallon

RECOMMENDED USES:

Properly prepared Interior or Exterior

surfaces such as: Wood, Drywall, Plaster,

Masonry, Metal, Well-bonded Wallpaper,

Brick, Stucco, Aluminum and Cinder Block.

Do not use on horizontal surfaces.

BEHR®

INTERIOR/EXTERIOR

OIL-BASED

SEMI-GLOSS ENAMEL

PAINT NO. 3830

DEEP BASE

COLORS

No. 3830 – Deep Base

Tintable Bases/Max Tint

No. 3830 - Deep Base Deep Base - 14 oz

Over 1600 custom colors plus computer color matching

FINISH

*Substrate Dependant

COVERAGE RATE

DRYING TIME

PRIMERS

COMPOSITION

Alkyd Resin

55.0%

69.7%

9.84 1bs.

VOC

Flashpoint

104°F (40º C)

MSDS

Clean Up

APPLICATION TOOLS

recommendations

SURFACE PREPARATION

APPLICATION

(18)

AVAILABLE IN: Quart & Gallon

RECOMMENDED USES:

Properly prepared Interior or Exterior

surfaces such as: Wood, Drywall, Plaster,

Masonry, Metal, Well-bonded Wallpaper,

Brick, Stucco, Aluminum and Cinder Block.

Do not use on horizontal surfaces.

BEHR®

INTERIOR/EXTERIOR

OIL-BASED

SEMI-GLOSS ENAMEL

PAINT NO. 3850

PASTEL BASE

COLORS

No. 3850 – Pastel Base

Tintable Bases/Max Tint

No. 3850 - Pastel Base Pastel Base - 8 oz

FINISH

*Substrate Dependant

COVERAGE RATE

DRYING TIME

PRIMERS

COMPOSITION

Alkyd Resin

54.0%

72.0%

10.91 1bs.

VOC

Flashpoint

104°F (40º C)

MSDS

Clean Up

APPLICATION TOOLS

recommendations

SURFACE PREPARATION

APPLICATION

(19)

AVAILABLE IN: Quart & Gallon

RECOMMENDED USES:

Properly prepared Interior or Exterior

surfaces such as: Wood, Drywall, Plaster,

Masonry, Metal, Well-bonded Wallpaper,

Brick, Stucco, Aluminum and Cinder Block.

Do not use on horizontal surfaces.

BEHR®

INTERIOR/EXTERIOR

OIL-BASED

SEMI-GLOSS ENAMEL

PAINT NO. 3860

ACCENT BASE

COLORS

No. 3860 – Accent Base

Tintable Bases/Max Tint

No. 3860 - Accent Base Accent Base – 14 oz

FINISH

*Substrate Dependant

COVERAGE RATE

DRYING TIME

PRIMERS

COMPOSITION

Alkyd Resin

55.7%

71.9%

10.0-12.0 1bs.

VOC

Flashpoint

104°F (40º C)

MSDS

Clean Up

APPLICATION TOOLS

recommendations

SURFACE PREPARATION

APPLICATION

(20)

AVAILABLE IN: Quart & Gallon

RECOMMENDED USES:

Properly prepared Interior or Exterior

surfaces such as: Wood, Drywall, Plaster,

Masonry, Metal, Well-bonded Wallpaper,

Brick, Stucco, Aluminum and Cinder Block.

Do not use on horizontal surfaces.

BEHR®

INTERIOR/EXTERIOR

OIL-BASED

HIGH-GLOSS ENAMEL

PAINT NO. 8800

ULTRA PURE WHITE

COLORS

No. 8800 - Ultra Pure White

Tintable Bases/Max Tint

No. 8800 - Ultra Pure White Ultra Pure White – 2 oz Over 1600 custom colors plus computer color matching