• No results found

Design of Columns as Per IS 456-2000

N/A
N/A
Protected

Academic year: 2021

Share "Design of Columns as Per IS 456-2000"

Copied!
68
0
0

Loading.... (view fulltext now)

Full text

(1)

Design of Compression

members-Axially Loaded columns

by

S.PraveenKumar Assistant Professor

Department of Civil Engineering PSG College of Technology

Coimbatore

(2)

Introduction

► A column is an important components of R.C. Structures.

► A column, in general, may be defined as a member carrying direct axial load which causes compressive stresses of such magnitude that these stresses largely control its design.

► A column or strut is a compression member, the effective length of which exceeds three times the least lateral dimension.

► When a member carrying mainly axial load is vertical, it is termed as column ,while if it is inclined or horizontal, it is termed as a strut.

► Columns may be of various shape such as circular, rectangular, square, hexagonal etc.

(3)

Classification of columns

3

Based on Type of Reinforcement

a) Tied Columns-where the main longitudinal bars are enclosed within closely spaced

lateral ties(

all cross sectional shapes)

b) Spiral columns-where the main longitudinal bars are enclosed within closely spaced and continuously wound spiral reinforcement (Circular, square, octagonal sections)

c) Composite Columns-where the reinforcement is in the form of structural steel sections or pipes, with or without longitudinal bars

(4)

Based on Type of Loading

a) Columns with axial loading (applied concentrically) b) Columns with uniaxial eccentric loading

c) Columns with biaxial eccentric loading

(5)

► The occurrence of ‘pure’ axial compression in a column (due to concentric loads) is relatively rare.

► Generally, flexure accompanies axial compression — due to ‘rigid frame’ action, lateral loading and/or actual(or even, unintended/accidental) eccentricities in loading.

► The combination of axial compression (P) with bending moment (M) at any column section is statically equivalent to a system consisting of the load P applied with an eccentricity e = M/P with respect to the longitudinal centroidal axis of the column section.

► In a more general loading situation, bending moments (Mx and My) are applied simultaneously on the axially loaded column in two perpendicular directions — about the major axis (XX) and minor axis (YY) of the column section. This results in biaxial eccentricities ex= Mx /P and ey = My /P, as shown in [Fig.(c)].

(6)

► Columns in reinforced concrete framed buildings, in general, fall into the third category, viz. columns with biaxial eccentricities.

► The biaxial eccentricities are particularly significant in the case of the columns located in the building corners.

► In the case of columns located in the interior of symmetrical, simple buildings, these eccentricities under gravity loads are generally of a low order (in comparison with the lateral dimensions of the column), and hence are sometimes neglected in design calculations.

► In such cases, the columns are assumed to fall in the first category, viz. columns with axial loading.

► The Code, however, ensures that the design of such columns is sufficiently conservative to enable them to be capable of resisting nominal eccentricities in loading

(7)

Based on Slenderness Ratio

Columns (i.e., compression members) may be classified into the following two types, depending on whether slenderness effects are considered insignificant or significant:

1. Short columns

2. Slender (or long) columns.

 ‘Slenderness’ is a geometrical property of a compression member which is related to the ratio of its ‘effective length’ to its lateral dimension. This ratio, called slenderness ratio, also provides a measure of the vulnerability to failure of the column by elastic instability (buckling) — in the plane in which the slenderness ratio is computed..

 Columns with low slenderness ratios, i.e., relatively short and stocky columns, invariably fail under ultimate loads with the material (concrete, steel) reaching its ultimate strength, and not by buckling.

(8)

 On the other hand, columns with very high slenderness ratios are in danger of buckling (accompanied with large lateral deflection) under relatively low compressive loads, and thereby failing suddenly.

Braced columns & unbraced column

In most of the cases, columns are also subjected to horizontal loads like wind, earthquake etc. If lateral supports are provided at the ends of the column, the lateral loads are borne entirely by the lateral supports. Such columns are known as braced columns.(When relative transverse displacement between the upper and lower ends of a column is prevented, the frame is said to be braced (against sideway)).

Other columns, where the lateral loads have to be resisted by them, in addition to axial loads and end moments, are considered as unbraced columns. (When relative transverse displacement between the upper and

lower ends of a column is not prevented, the frame is said to be

unbraced

(9)

9 In such cases, the effective length ratio k varies between 0.5 and 1.0

(10)

10 In such cases, the effective length ratio

k

varies between

1.0 and infinity

(11)

Reinforcement in column

► Concrete is strong in compression.

► However, longitudinal steel rods are always provided to assist in carrying the direct loads.

► A minimum area of longitudinal steel is provided in the column, whether it is required from load point of view or not.

► This is done to resist tensile stresses caused by some eccentricity of the vertical loads.

► There is also an upper limit of amount of reinforcement in RC columns, because higher percentage of steel may cause difficulties in placing and compacting the concrete.

► Longitudinal reinforcing bars are “tied” laterally by “ties” or “stirrups” at suitable interval so that the bars do not buckle

(12)

Codal Provisions(IS-456-2000)

12

(13)

13

(14)

14

(15)

15

(16)
(17)

Functions of longitudinal reinforcement

► To share the vertical compressive load, thereby reducing the overall size of the column.

► To resist tensile stresses caused in the column due to (i) eccentric load (ii) Moment (iii) Transverse load.

► To prevent sudden brittle failure of the column. ► To impart certain ductility to the column.

► To reduce the effects of creep and shrinkage due to sustained loading.

(18)

18

(19)

19

(20)

20

(21)

Functions of Transverse reinforcement

► To prevent longitudinal buckling of longitudinal reinforcement. ► To resist diagonal tension caused due to transverse shear due to

moment/transverse load.

► To hold the longitudinal reinforcement in position at the time of concreting.

► To confine the concrete, thereby preventing its longitudinal splitting. ► To impart ductility to the column.

► To prevent sudden brittle failure of the columns.

(22)

22

Clause 26.5.3.2 Page No:49–IS 456-2000

Cover to reinforcement

For a longitudinal reinforcing bar in a column, the nominal cover shall not be less than 40mm, nor less than the diameter of such bar.

In the case of columns of minimum dimension of 200mm or under, whose reinforcing bars does not exceed 12mm, a cover of 25mm may be used.

(23)

23

(24)

Assumptions in Limit State of Collapse -Compression

24

(25)

25

(26)

26

(27)
(28)
(29)
(30)

30

(31)

31

a) Termination of column bars inside slab b) Fixed end joint in a column

(32)

32

(33)
(34)

Design of Compression

members-Uniaxial Bending

(35)

Based on Type of Loading

a) Columns with axial loading (applied concentrically) b) Columns with uniaxial eccentric loading

c) Columns with biaxial eccentric loading

(36)

► The occurrence of ‘pure’ axial compression in a column (due to concentric loads) is relatively rare.

► Generally, flexure accompanies axial compression — due to ‘rigid frame’ action, lateral loading and/or actual(or even, unintended/accidental) eccentricities in loading.

► The combination of axial compression (P) with bending moment (M) at any column section is statically equivalent to a system consisting of the load P applied with an eccentricity e = M/P with respect to the longitudinal centroidal axis of the column section.

► In a more general loading situation, bending moments (Mx and My) are applied simultaneously on the axially loaded column in two perpendicular directions — about the major axis (XX) and minor axis (YY) of the column section. This results in biaxial eccentricities ex= Mx /P and ey = My /P, as shown in [Fig.(c)].

(37)

► Columns in reinforced concrete framed buildings, in general, fall into the third category, viz. columns with biaxial eccentricities.

► The biaxial eccentricities are particularly significant in the case of the columns located in the building corners.

► In the case of columns located in the interior of symmetrical, simple buildings, these eccentricities under gravity loads are generally of a low order (in comparison with the lateral dimensions of the column), and hence are sometimes neglected in design calculations.

► In such cases, the columns are assumed to fall in the first category, viz. columns with axial loading.

► The Code, however, ensures that the design of such columns is sufficiently conservative to enable them to be capable of resisting nominal eccentricities in loading

(38)

Column under axial compression and Uni-axial

Bending

► Let us now take a case of a column which is subjected to combined action of axial load (Pu) and Uni-axial Bending moment (Mu).

► This case of loading can be reduced to a single resultant load Pu acting at an eccentricity e such that e= Mu / Pu .

► The behavior of such column depends upon the relative magnitudes of Mu and Pu , or indirectly on the value of eccentricity e.

► For a column subjected to load Pu at an eccentricity e, the location of neutral axis (NA) will depend upon the value of eccentricity e.

► Depending upon the value of eccentricity and the resulting position (Xu) of NA., We will consider the following cases.

(39)

 Case I : Concentric loading: Zero Eccentricity or nominal eccentricity (Xu =∞)

 Case II : Moderate eccentricity (Xu > D)

 Case III : Moderate eccentricity (Xu = D)

 Case IV : Moderate eccentricity (Xu < D) Case I (e=0 and e<emin )

(40)

7

(41)

8

(42)

9

(43)

Modes of Failure in Eccentric Compression

► The mode of failure depends upon the relative magnitudes of eccentricity e. (e = Mu / Pu )

10

Eccentricity Range Behavior Failure

e = Mu / Pu Small Compression Compression

e = Mu / Pu Large Flexural Tension

e = Mu / Pu In between

two

(44)

Column Interaction Diagram

► A column subjected to varying magnitudes of P and M will act with its neutral axis at varying points.

(45)

Method of Design of Eccentrically loaded short column

12

The design of eccentrically loaded short column can be done by two methods

I) Design of column using equations

(46)

Design of column using equations

(47)
(48)

15

(49)
(50)

Design of Compression

members-Biaxial Bending

(51)

Introduction

► A column with axial load and biaxial bending is commonly found in structures because of two major reasons:

Axial load may have natural eccentricities, though small, with respect to both the axes.

Corner columns of a building may be subjected to bending moments in both the directions along with axial load

Examples

1) External façade columns under combined vertical and horizontal load

2) Beams supporting helical or free-standing stairs or oscillating and rotary machinery are subjected to biaxial bending with or without axial load of either compressive or tensile stress.

(52)

Biaxial Eccentricities

Every column should be treated as being

subjected to axial compression along with

biaxial bending by considering possible

eccentricities of the axial load with respect to

both the major axis(xx-axis) as well as minor

axis (yy-axis).

These eccentricities, designated as e

x

and

e

y

with respect of x and y axes, may be

atleast e

min

though in majority of cases of

biaxial bending, these may be much more

(53)
(54)

Method Suggested by IS 456-2000

The method set out in clause 39.6 of the code is based on an

assumed failure surface that extends the axial load-moment

diagram (P

u

-M

u

) for single axis bending in three dimensions.

Such an approach is also known as

Breslar’s Load contour

method.

According to the code, the left hand side of the equation

(55)

Shall not exceed 1. Thus we have

The code further relates αn to the ratio of Pu/Puz as under:

For intermediate values, linear interpolation may be done from figure.

Load Puz is given by

Load Puz may be evaluated from chart 63 of ISI

Handbook(SP-16-2000) 6

(56)

Design of Column

Step-1

-Assume the cross-section of the column and the area of

reinforcement along with its distribution, based on moment M

u

given by equation

where a may vary between 1.10 to 1.20-

lower of a for higher axial loading (P

u

/P

uz

)

Step-2

- Compute P

uz

either using Equation or chart. Find ratio of

P

u

/P

uz.

Step-3

- Determine Uniaxial Moment Capacities M

ux1

and M

uy1

combined with axial load P

u

, using Appropriate Interaction

curves(Design charts) for case of column subjected to axial load

(P

u

) and Uniaxial Moment.

(57)

Step-4

-Compute the values of M

ux

/M

ux1

and M

uy

/M

uy1

from chart

64 of SP-16, Find the permissible value of M

ux

/M

ux1

corresponding

top the above values of M

uy

/M

uy1

and P

u

/P

uz

.If actual value of

M

ux

/M

ux1

is more than the above value found from chart 64 of SP

16, the assumed section is unsafe and needs revision. Even if the

assumed value is over safe, it needs revision for the sake of

economy.

(58)

9

(59)

Design of Slender Columns

(60)

Introduction

► A Compression member may be considered as slender or long when the slenderness ratio lex/D and ley/b are more than 12.

► Thus, if lex/D > 12, the column is considered to be slender for bending about x-x axis, while if ley/b > 12, the column is considered to be slender for bending about y-y axis.

► When a short column is loaded even with an axial load, the lateral deflection is either zero or very small.

► Similarly when a slender column is loaded even with axial load, the lateral deflection ∆, measured from the original centre line along its length, becomes appreciable.

(61)

The design of a slender column can be carried out by following

simplified methods

1) The Strength Reduction Coefficient method 2) The Additional moment Method

3) The Moment Magnification Method

The reduction coefficient method, given by IS 456-2000 is recommended for working stress design for service load and is based on allowable stresses in steel and concrete.

The additional moment method is recommended by Indian and British codes.

The ACI Code recommends the use of moment magnification method.

3

(62)

4

(63)

Determination of Total Moment

(64)
(65)

Bending of columns in frames

7

(66)

Procedure for Design of Slender Column

Step-1- Determine the Effective Length and Slenderness Ratio in each direction

Step-2- (a) Determine Initial Moment (Mui) from given primary end moments Mu1 and Mu2 in each direction.

(b) Calculate emin and Mu,min in each direction.

(c) Compare moments computed in steps (a) and (b) above and take the greater one of the two as initial moment Mui ,in each direction.

Step-3- (a) Compute additional moment (Ma) in each direction, using equation

(67)

(b) Compute total moment (Mut ) in each direction from using equation without considering reduction factor (ka)

(c) Make Preliminary design for Pu and Mut and find area of steel. Thus p is known.

Step-4- (a) Obtain Puz. Also obtain Pb in each direction, for reinforcement ration p determined above.

(b) Determine the value of ka in each direction.

(c) Determine the Modified design value of moment in each direction

Mut = Mui + ka Ma

(68)

Step-5- Redesign the column for Pu and Mut . If the column is slender about both the axes, design the column for biaxial bending, for (Pu , Muxt) about x-axis and (Pu , Muyt) about y-axis.

Note-When external moments are absent, bending moment due to minimum eccentricity should be added to additional moment about the corresponding axes.

References

Related documents

lagneçe: lagna lord; räjyabhävasthe: placed in 10 th house; räjyeçe: 10 th lord; lagnasaàsthite: placed in lagna; | prabalo: with strength; räjasambandhayogo'yaà: raja

All

Figure 6.12 Transmittance peak wavelength (left) and peak transmittance (right) of the configured PC straight waveguide as function of an air hole diameter randomness in the form of

In a study of online comments, Coe, Kenski, and Rains (2014) found that uncivil commenters were slightly more likely to include statistics as evidence; uncivil comments were also

We considered that all operators performed the task intuitively, like conventional laparoscopic surgery, without a sense of discomfort due to the relationship between the

Four key organizations are actively involved in this process: the Council of University Presidents of Thailand (CUPT), the Office of Higher Education Commission, the Office

The result showed MetS group generally have higher value of ONH parameters as compared to Non-MetS group with exception of two ONH parameters; disc area and rim area6.

We also analyzed our own past data to inform our decisions in improving our system, examining the frequency of compiler error types, and focusing on the most