• No results found

Scattering of SH waves by a Griffith crack in a long strip at asymmetric position

N/A
N/A
Protected

Academic year: 2020

Share "Scattering of SH waves by a Griffith crack in a long strip at asymmetric position"

Copied!
10
0
0

Loading.... (view fulltext now)

Full text

(1)

IN A LONG STRIP AT ASYMMETRIC POSITION

S. GHOSH, S. MANNA, AND S. C. MANDAL

Received 11 April 2005

The scattering of SH-waves by a Griffith crack in an infinitely long elastic strip situated at an asymmetric position has been analyzed. Applying Fourier transform, the mixed boundary value problem has been reduced to the solution of dual integral equations which finally has been reduced to the solution of a Fredholm integral equation of sec-ond kind. The numerical values of stress intensity factor, crack opening displacement, and scattered field outside the crack have been illustrated graphically to show the effect of asymmetry of the crack position.

1. Introduction

Cracks or inclusions are present essentially in most of the structural materials, either as natural defects or as a result of fabrication processes. The diffraction of elastic waves be-comes more practical when boundaries are present in the medium. Great attention has been given to the study of diffraction of elastic waves by cracks situated at asymmetric po-sition . Loeber and Sih [5] and Mal [6] have studied the problem of diffraction of elastic waves by a Griffith crack in an infinite medium. The problem of finite crack at the inter-face of two elastic half-spaces has been discussed by Srivastava et al. [11] and Bostr¨om [2]. Finite crack perpendicular to the surface of the infinitely long elastic strip has been stud-ied by Chen [3] and by Srivastava et al. [10]. Shindo et al. [9] considered the problem of impact response of a finite crack in an orthotropic strip. Crack in inhomogeneous elastic strip has been analyzed by Sarkar et al. [8]. Matysiak and Pauk [7] studied edge crack in an elastic layer resting Winkler foundation. Recently, Birinci and Erdol [1] analyzed the problem of a layered composite containing a crack in its lower loaded-by-rigid stamp.

In our note, we have treated the diffraction of SH-waves by a crack situated at asym-metric position in an infinitely long elastic strip which has not been considered yet. This type of situation arises in almost all cases of fabrication processes in construction tech-nology. Applying the Fourier transform, the mixed boundary value problem has been converted to the solution of dual integral equations. The dual integral equations have been finally reduced to a Fredholm integral equation of second kind by applying Abel’s transform. Expressions for the stress intensity factor and crack opening displacement

Copyright©2005 Hindawi Publishing Corporation

(2)

z

−c

0

1 1

b x

[image:2.468.137.328.67.243.2]

y

Figure 2.1. Geometry of the crack.

have been plotted to show the asymmetry of the crack position. Also stress (scattered field) outside the crack has been calculated and shown by three-dimensional graph.

2. Formulation

Consider the boundary value problem of interaction of SH-waves by Griffith crack sit-uated at the asymmetric position in an infinitely long elastic strip−d1≤x1≤d2,−∞< y1<∞. The crack is located in the region−a < x1< a,−∞< z1<∞,y1=0. Normalizing all the lengths with respect toaand putting

x1 a =x,

y1 a =y,

z1 a =z,

d1 a =c,

d2

a =b, (2.1)

the location of the crack becomes1≤x≤1,−∞< z <∞,y=0 (Figure 2.1) referring to a Cartesian coordinate system (x,y,z). Let a plane harmonic SH-wave originating at y= −∞impinge on crack normally to thex-axis. The only nonvanishingz-component of displacement which is independent ofzisw(x,y,z)=W(x,y)e−iωt. Now our problem reduces to the solution of the equation

2W ∂x2 +

2W ∂y2 +k

2

2W=0, (2.2)

where

k2=aω c2

(3)

is subject to the boundary conditions

τyz(x, 0)0e−iωt, |x|<1, (2.4) W(x, 0)=0, −c≤x≤ −1, 1≤x≤b, (2.5)

τxz(−c,y)=0, |y|<∞, (2.6)

τxz(b,y)=0, |y|<∞. (2.7)

Henceforth, the time factore−iwtwhich is common to all field variables would be omit-ted in the sequal.

The nonvanishing stresses are

τyz=µ∂W

∂y , (2.8)

τxz=µ∂W

∂x . (2.9)

The solution of (2.2) can be taken as

W(x,y)=

−∞A(ξ)e

−αyeiξx

+

0

B(ζ)eβx+C(ζ)e−βxsin(ζ y)dζ, y >0,

(2.10)

where

α=ξ2k2

2, β=

ζ2k2

2. (2.11)

Therefore the expressions of stresses are

τyz(x,y)= −µ

−∞αA(ξ)e

−αyeiξx

+µ

0 ζ

B(ζ)eβx+C(ζ)e−βxcos(ζ y)dζ,

(2.12)

τxz(x,y)=iµ

−∞ξA(ξ)e

−αyeiξx

+µ

0 β

B(ζ)eβx−C(ζ)e−βxsin(ζ y)dζ.

(4)

From the boundary conditions (2.6) and (2.7),B(ζ) andC(ζ) can be found to be

B(ζ)= 2iζ

πβe2e2

e−cβ

−∞

ξA(ζ)e−icξ α2+ζ2 dξ−e

−∞

ξA(ζ)eibξ α2+ζ2

,

C(ζ)= 2iζ

πβe2e2

ecβ

−∞

ξA(ζ)e−icξ α2+ζ2 dξ−e−

−∞

ξA(ζ)eibξ α2+ζ2

.

(2.14)

Now, from boundary conditions (2.4) and (2.5), we obtain the following dual integral equations for the determination of the unknown functionA(ζ):

−∞αA(ξ)e

iξx=p(x), |x|<1, (2.15)

−∞A(ξ)e

iξx=0, cx≤ −1, 1xb, (2.16)

where

p(x)=τ0 µ +

0 ζ

B(ζ)eβx+C(ζ)e−βxdζ. (2.17)

3. Method of solution

In order to reduce the dual integral equations (2.15) and (2.16) to a single Fredholm integral equation, we assume that

A(ξ)=τ0

1

0tg(t)J0(ξt)dt (3.1)

so that (2.16) is automatically satisfied. Now, (2.15) can be written as

1

0ξ

1 +H(ξ)A(ξ) cos(ξx)dξ= p(x)

2 , |x|<1, (3.2)

where

H(ξ)= α

ξ 1

. (3.3)

(5)

be converted to the following Fredholm integral equation of second kind:

g(t) + 1

0ug(u)L(u,t)du=1, (3.4)

where

L(u,t)=L1(u,t)−L2(u,t)−L3(u,t),

L1(u,t)=

0 ξH(ξ)J0(ξu)J0(ξt)dξ, L2(u,t)=1

2

0 ζ2I

0(βu)

1 +e−2 βe2e2

I0(βt) +L0(βt)

dζ,

L3(u,t)=1 2

0 ζ2I

0(βu)

1 +e−2 βe2e2

I0(βt)−L0(βt)

dζ.

(3.5)

Using contour integration technique [11], the integralL1(u,t) can be converted to the following finite integral:

L1= −ik22

1

0

1−η2J

0

k2ηt

H0(1)

k2ηu

dη, u > t,

= −ik2 2

1

0

1−η2J

0

k2ηu

H0(1)

k2ηt

dη, u < t.

(3.6)

Now, puttingb=c=h, we can find the following result for Griffith crack in a symmetric position:

L(u,t)= −ik22

1

0

1−η2J

0

k2ηt

H0(1)

k2ηu

+

0 ζ2I

0(βu)I0(βt)e−βh βsinh(βh) dζ.

(3.7)

4. Quantities of physical interest

The shear stressτyz(x,y) in the planez=0 in the neighborhood of the crack can be found from (2.12) and is given by

τyz(x, 0)= −µ

∞αA(ξ)e

iξx+µ

0 ζ

B(ζ)eβx+C(ζ)e−βxdζ. (4.1)

(6)

the stress can be presented as

τyz(x, 0)=√τ0x

x21g(1) +O(1), |x|>1. (4.2)

Defining the stress intensity factorKby

K= lim x→1+

x−yz(x, 0) τ0

, (4.3)

we obtain

K=√1

2g(1). (4.4)

Now, crack opening displacement

W(x, 0)=W(x, 0+)−W(x, 0−) (4.5)

can be obtained from (2.10) as

W(x, 0)=2

−∞A(ξ)e

iξx, |x|<1, (4.6)

which on substitution of the value of A(ξ) from (3.1) takes the form

W(x, 0)=2τ0a µ

1

x tg(t)

t2x2dt, |x|<1. (4.7)

Scattered fieldτyz(x,y) forx >1,z >0 is calculated from (2.12), (2.14), and (3.1) and is represented by the expression

τyz(x,y)= −τ0

0

1

0αtg(t)J0(ξt)e

−αycos(ξx)dξ dt

+τ0

0

1

0

ζ22e2+e2+e2cos(ζ y)eβx

β1−e−2 I0(tβ)tg(t)dζ dt,

(4.8)

(7)

0 0.2 0.4 0.6 0.8 1 1.2 k2

0 0.2 0.4 0.6 0.8 1 1.2 1.4

SIF

c=2

b=2.5

b=3.5

[image:7.468.120.348.66.304.2]

b=4.5

Figure 5.1. Dynamic SIF versus dimensionless frequencyk2.

5. Numerical results and discussion

The method of Fox and Goodwin [4] has been used to solve the integral equation (3.4) numerically for different values of dimensionless frequencyk2and b,cwhich indicate the asymmetry in position of the crack. The integral in (3.4) has been represented by a quadrature formula involving values of the desired functiong(t) at pivotal points inside the specified range of integration, and then converted to a set of simultaneous linear algebraic equations. The solution of linear algebraic equations gives a first approximation to the pivotal values ofg(t), which has been improved by the use of difference-correction technique.

After solving the integral equation (3.4) numerically, the stress intensity factor (SIF)K and crack opening displacement (COD)µW(x, 0)/τ0ahave been calculated numerically and plotted separately againstk2 and dimensionless distancex(0< x <1), respectively, for different values ofbandcto show the effect of positional symmetry of the crack.

In Figures5.1and5.2, SIF(K) is plotted againstk2(0.1≤k21). InFigure 5.1, the ef-fect of positional asymmetry of the crack is shown by varying one boundaryb(=2.5, 3.5, 4.5) while the other boundaryc(=2) is kept fixed and inFigure 5.2, same effect has been shown by varyingc(=1.5, 2.5, 3.5) withb=2. In both cases, it is observed that the SIF is increasing initially and then slowly decreasing neark2=1 for less asymmetry in position and shows wave-like nature, and finally decreasing neark2=1 as asymmetry in position increases.

(8)

0 0.2 0.4 0.6 0.8 1 1.2 k2

0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6

SIF

b=2

c=2.5

c=3.5

[image:8.468.120.350.69.301.2]

c=4.5

Figure 5.2. Dynamic SIF versus dimensionless frequencyk2.

0 0.2 0.4 0.6 0.8 1 1.2

x 0

0.5 1 1.5 2 2.5

COD

k2=1.5

k2=1

k2=0.5

Figure 5.3. Crack opening displacement versus dimensionless distance;b=2,c=4.

[image:8.468.119.350.352.526.2]
(9)

0 0.2 0.4 0.6 0.8 1 1.2 x

0 0.5 1 1.5 2 2.5

COD

k2=1.5 k2=1

[image:9.468.121.351.65.235.2]

k2=0.5

Figure 5.4. Crack opening displacement versus dimensionless distance;b=4,c=2.

2.8 2.4

2.0 1.6

1.2 y

2.8 2.4 2.0 1.6 1.2

x 0.4

0.6 0.8 1

τyz

(x

,y

)/τ

0

Figure 5.5. Scattered field outside the crack (b=4,c=3; andk2=0.4).

decreasing with increases inxas well asyand near boundary, it shows wave-like nature due to boundary effect.

References

[1] A. Berinci and R. Erdol,A layered composite containing a crack in its lower layer loaded by rigid

stamp, Eur. J. Mech. A Solids23(2004), no. 6, 909–924.

[2] A. Bostr¨om,Elastic wave scattering from an interface crack: antiplane strain, J. Appl. Mech.54

(1987), 503–508.

[3] E. P. Chen,Sudden appearance of a crack in a stretched finite strip, J. Appl. Mech.45(1978), 277–280.

[4] L. Fox and E. T. Goodwin,The numerical solution of non-singular linear integral equations, Phi-los. Trans. Roy. Soc. London Ser. A245(1953), 501–534.

[image:9.468.121.349.281.420.2]
(10)

[6] A. K. Mal,Interaction of elastic waves with a Griffith crack, Internat. J. Engrg. Sci.8(1970), no. 9, 763–776.

[7] S. J. Matysiak and V. J. Pauk,Edge crack in an elastic layer resting on Winkler foundation, Engrg. Fracture Mech.70(2003), no. 17, 2353–2361.

[8] J. Sarkar, S. C. Mandal, and M. L. Ghosh,Diffraction of SH-waves by a Griffith crack in

nonho-mogeneous elastic strip, Arch. Mech.45(1993), no. 3, 285–294.

[9] Y. Shindo, H. Nozaki, and H. Higaki,Impact response of a finite crack in an orthotropic strip, Acta Mech.62(1986), 87–104.

[10] K. N. Srivastava, O. P. Gupta, and R. M. Palaiya,Interaction of elastic waves with a Griffith cracks

situated in an infinitely long strip, Z. Angew. Math. Mech.61(1981), 583–587.

[11] K. N. Srivastava, R. M. Palayiaya, and D. S. Karaulia,Interaction of antiplane shear waves by a

Griffith crack at the interface of two bounded dissimilar elastic half-spaces, Int. J. Fracture.16

(1980), no. 4, 349–358.

S. Ghosh: Department of Mathematics, Faculty of Science, Jadavpur University, Calcutta-700 032, India

E-mail address:samit gh@yahoo.com

S. Manna: Department of Mathematics, Faculty of Science, Jadavpur University, Calcutta-700 032, India

E-mail address:jumscm@hotmail.com

S. C. Mandal: Department of Mathematics, Faculty of Science, Jadavpur University, Calcutta-700 032, India

Figure

Figure 2.1. Geometry of the crack.
Figure 5.1. Dynamic SIF versus dimensionless frequency k2.
Figure 5.3. Crack opening displacement versus dimensionless distance; b = 2,c = 4.
Figure 5.4. Crack opening displacement versus dimensionless distance; b = 4,c = 2.

References

Related documents

La distance de sécurité entre la plaque de cuisson en céramique et le placard situé au- dessus de la plaque chauffante doit être d’au moins 760

Securing access to land often secures access to water as well and this enables farmers to invest with confidence in management practices and technologies that enables them to

and the processes involved in their diversification, we collected and analyzed 419 samples in situ across the country (cultivated plants from old orchards and vines growing in

FIPS Code — The Federal Information Processing Standard (FIPS) is a 5-digit number assigned to each county in the

Knowledge and application of Public Service Act, Public Service Regulations, Labour Relations Act, Skills Development Act, Basic Conditions of Employment Act,

foundation year by integrating it into the school curriculum; improve the curriculum of the Arabic language to increase proficiency of students; restructure kindergarten and

The clean screen is not available for HMI devices with touch screen and function keys. In this case, configure a screen without operator controls,

Rare splice mutations of both genes in introns with non-conserved splice sites and with unknown prevalence are not detected by DNA based diagnostics, they can only be identified