Heat Pump GSM Remote Control

Heat Pump GSM Remote Control

Control your heat pump from anywhere. Easy to use.

Access Code -protection to prevent unauthorized remote access.

Easy access to most frequently used controls. A total of 7 remote controlled heat pump related functions/parameters.

Installation

1. Insert the SIM card to cell phone

Heat Pump GSM Remote Control

SIM card

2. Plug in the charger and hands-free cables to phone

hands-free cable charger cable

4. Turn on the Mini-GSM controller

3. Turn on the phone and enter your SIM card PIN code

Power on + insert PIN

Installation

(continues...)

Heat Pump GSM Remote Control

5. Make sure the front panel of the GSM remote controller points toward the indoor unit.

6. Now your setup should look like this and you are ready to configure cell phone!

Installation

(Configuring cell phone)

Heat Pump GSM Remote Control

There are a few settings to set right in cell phone (in this case we are using Nokia 3120) before we can start remote controlling.

1. Make sure you have general profile in use. If you are unsure what profile you have in use, hit power button once and choose ”General”.

2. Go to ”Menu -> Profiles -> General -> Personalise” and make sure everything there is set as follows:

Incoming call alert: Ringing Ringing tone: Croak

Ringing volume: Level 1 (= min) Vibrating alert: Off

Message alert tone: Off

Keypad tones: Level 3 (= max) Warning tones: Off

Rhythmic backlight alert: Off Alert for: All calls

3. Make sure you have handsfree cable attached to cell phone.

4. Go to ”Menu -> Settings -> Enhancement settings -> Headset” and make sure everything there is set as follows:

Default profile: Current Profile Automatic answer: On

5. Make a call to cell phone attached to a GSM remote controller. When cell phone automatically answers to your call press its

button until volume is set to max level.

How to use?

1. Make a call to Mini-GSM remote control attached cell phone.

Heat Pump GSM Remote Control

other control commands cooling

automatic

Basic functions

2. Cell phone attached

will answer to your call automatically.

to Mini-GSM remote control

3. Enter your remote controller Access Code and start controlling your heat pump.

Can I change or disable Access Code?

I unlocked the remote controller using Access Code. How long it takes before it reactivates?

No.

Reactivation happens about 2 min after last button press.

i-save

Fan Vane #00 = Auto #02 = Low #03 = Medium #04 = High #05 = Super High #10 = Auto #11 = 1 #12 = 2 #13 = 3 #14 = 4 #15 = 5 #16 = Swing #01 = Quiet

Heat pump related commands

#40 = Off #41 = On EconoCool

Heat Pump GSM Remote Control

GSM remote controller related commands

Operation mode: Heating Fan speed: Super High Vane: Swing EconoCool: Off i-save: Off Power: Off Temperature: 22 Autosend: On

(Note: Resetting the GSM remote controller does not send any control messages to the heat pump)

#90 = Reset GSM remote controller with following settings:

#95 = Autosend OFF #96 = Autosend ON

#97 = GSM remote controller sound OFF

#98 = GSM remote controller sound SHORTER VERSION #99 = GSM remote controller sound ON+RESET

GSM remote controller sound: On

Heat Pump GSM Remote Control

What is Autosend?

I entered a command that is not on these lists. What happens now?

When recovering from power outage, does the GSM remote controller automatically send commands to the heat pump?

Default function of Mini GSM remote controller is to send IR control message to heat pump right after every command or control.

This function can be turned off so that only * button sends control message to heat pump.

If you have Autosend on, currently active settings are sent to heat pump.

No. GE25/35 heat pump has ”Auto restart function”.

Remote control example

(step by step)

Heat Pump GSM Remote Control

- Power: On

- Operation mode: Heating - Temperature: 24

(1-2-6-3-3)

Press 1 (power: on). You will hear multiple beeps to indicate that IR control is sent to heat pump.

Press 2 (operation mode: heating). You will hear multiple beeps to indicate that IR control is sent to heat pump.

Press 6 (temperature: 22C). You will hear multiple beeps to indicate that IR control is sent to heat pump.

Press 3 ( ). You will hear multiple beeps to indicate that IR control is sent to heat pump.

temperature: +1C

Press 3 again to increase temperature by 1C. You will hear multiple beeps to indicate that IR control is sent to heat pump.

In this example Autosend is assumed to be on.

If you have set Autosend off in your GSM controller, then button sequence would be (1-2-6-3-3-*)

Remote control examples

Heat Pump GSM Remote Control

- Power: On

- Operation mode: Heating - Temperature: 24

(1-2-6-3-3)

- Power: On

- Operation mode: Cooling - Temperature: 21

(1-8-6-9)

- Power: On

- Operation mode: i-save - Temperature: 10

(1-0)

- Power: Off (4)

- Fan: Super High (#-0-5)

- Reset GSM remote controller (#-9-0)

In this example Autosend is assumed to be on.

If you have set Autosend off in your GSM controller, then you need to add * to end of every button sequence.

i-save function in Mini GSM Remote Controller:

When activating i-save function by pressing button 0, operation mode is automatically set to heating with temperature of 10C°.

Any attempt to modify operation mode or temperature will automatically cancel/release i-save function!

Please note that i-save function of Mini GSM Remote Controller is not designed to be used for storing settings as original GE series hand held remote controller does.

Heat Pump GSM Remote Control

GSM Remote Controller

front & rear panel

Indicators Power on Controller unlocked GSM button press Power cord GSM hf cord Infra-red signal transmitter