Outside Telephone Cable

(1)

Description

Soft copper wires insulated with high density polyethylene, foam skin or solid.

Filled core, conformed by groups of pairs or by unit of groups of pairs. Aluminum

shield and external jacket in polyethylene type moisture barrier.

Construction

Conductor

Soft copper wires

Insulation

Foam skin or solid high density polyethylene.

Twisted Pairs

Insulated conductors are twisted into pairs

Core Assembly

Up to 70 pairs, groups of 10 pairs, from 100 to 300 pairs groups of 25 pairs,

from 400 pairs and more, units of 100 pairs (each unit is conformed by 4 groups

of 25 pairs)

Spare pairs

One spare pair white-red colored at the interstices of each 100 pairs unit, to

guarantee nominal numbers of pairs.

Identification

Pairs, groups and units that conform the core, are identified by color code

(Attached)

Core Wrap

Non-hygroscopic dielectric tape. Offers dielectric strength between core and

sheath

Shield

Corrugated Aluminum tape both sides covered with copolymer

Jacket

Black polyethylene, abrasion, weather, and penetration to water resistant

Outside Telephone Cable

Filled Core. Moisture Barrier.

(2)

Moisture Barrier

Filled Core with elastomeric compound, aluminum tape both sides

covered with copolymer and polyethylene external jacket, firmly bonded

to external side of aluminum tape

Options

Manufacturing according to REA and/or Bellcore specifications

Shield in Flat Aluminum tape. Armor in corrugated and copolymer

covered Steel tape for direct buried and for rodent protection. Galvanized

steel wires armor for vertical installations. Other Core Assemblies are

available upon request.

Applications

Trunk cable and distribution cable networks. Special for wet locations;

the elastomeric compound filler prevents the entrance of moisture to

the core. Installation in ducts or raceways; for buried direct in locations

without heavy traffic.

CENTELSA Outside Telephone Cable, are able for voice and data

transmission up to 6.3 MHz, optimizing the bandwidth of copper cables.

Standards and Specifications

CENTELSA Outside Telephone Cable, are manufactured under the

following standards:

ANSI/ICEA S-84-608 Telecommunications cable filled, polyolefin

insulated copper conductor.

ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin

insulated copper conductor.

NTC-2061 Telecommunications copper conductor multipair cables,

polyolefin insulated and covered, filled and dry.

Certifications

CENTELSA Outside Telephone Cable, are certified by:

ICONTEC (Colombia). Norma NTC 2061.

Note: Other configurations, sizes, colors and length not specified

herein are available upon request.

(3)

Note: 1. Data herein indicated are approximated and are subject to normal manuracturing tolerances. NOMINAL PAIRS STANDARD LENGTH BY REEL (m) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) OVERALL DIAMETER (mm) SPARE PAIRS CONDUCTOR DIAMETER (mm) JACKET THICKNESS (mm) 94 141 187 231 275 356 479 692 886 1270 1668 2044 2419 3565 4699 5837 6941 9126 120 188 252 316 378 498 682 996 1283 1876 2446 3037 3606 5312 7018 8684 10386 13682 158 257 350 442 531 724 994 1452 1880 2732 3605 4475 5309 7848 10374 12846 15371 20280 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.60 1.80 1.80 1.80 2.00 2.20 2.40 2.40 2.40 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.80 1.80 2.00 2.00 2.20 2.40 2.40 2.60 2.60 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.80 1.80 1.80 2.00 2.20 2.20 2.40 2.60 2.60 2.80 2.80 9.75 11.56 12.96 14.13 15.17 16.96 19.30 22.87 25.48 29.91 34.06 37.35 40.32 48.48 55.32 61.43 66.73 75.88 10.67 12.86 14.55 15.97 17.23 19.40 22.22 26.46 29.62 35.40 39.92 44.39 47.99 57.64 66.03 72.92 79.57 90.63 12.08 14.86 17.00 18.80 20.38 23.55 27.13 32.38 36.39 43.25 49.38 54.80 59.35 71.67 81.99 90.72 99.02 113.03 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 -1 2 2 3 4 5 6 9 12 15 18 24 -1 2 2 3 4 5 6 9 12 15 18 24 -1 2 2 3 4 5 6 9 12 15 18 24

Outside Telephone Cable.

Filled Core. Moisture Barrier.

Foamed-Skin polyethylene insulation.

Standards: ANSI/ICEA S-84-608 Telecommunications cable filled, polyolefin insulated copper conductor.

NTC-2061 Telecommunications copper conductor multipair cables, polyolefin insulated and covered, filled and dry.

(4)

Outside Telephone Cable.

Filled Core. Moisture Barrier.

Solid polyethylene insulation.

Note: 1. Data herein indicated are approximated and are subject to normal manuracturing tolerances.

106 160 211 262 311 405 548 792 1015 1476 1913 2377 2812 4128 5440 6714 8026 10547 142 224 306 384 459 620 850 1232 1590 2300 3033 3762 4454 6561 8663 10713 12813 16877 177 294 407 514 624 849 1168 1710 2215 3262 4292 5324 6320 9325 12270 15260 18183 24082 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.80 1.80 2.00 2.00 2.20 2.40 2.40 2.60 2.60 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.80 1.80 1.80 2.00 2.20 2.20 2.40 2.60 2.60 2.80 2.80 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.80 1.80 2.00 2.20 2.40 2.40 2.60 2.60 2.80 2.80 3.00 10.34 12.40 13.98 15.32 16.49 18.53 21.18 25.18 28.15 33.59 37.83 42.05 45.43 54.51 62.26 68.88 75.13 85.52 11.83 14.51 16.57 18.30 19.83 22.90 26.34 31.42 35.27 41.88 47.81 53.04 57.42 69.31 79.26 87.67 95.68 109.18 13.13 16.35 18.82 20.90 22.74 26.33 30.47 36.49 41.11 49.45 56.44 62.83 68.10 82.11 93.57 104.08 113.20 129.82 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 -1 2 2 3 4 5 6 9 12 15 18 24 -1 2 2 3 4 5 6 9 12 15 18 24 -1 2 2 3 4 5 6 9 12 15 18 24 NOMINAL PAIRS STANDARD LENGTH BY REEL (m) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) OVERALL DIAMETER (mm) SPARE PAIRS CONDUCTOR DIAMETER (mm) JACKET THICKNESS (mm)

(5)

Outside Telephone Cable

Description

Soft copper wires insulated with high density polyethylene, foam skin or solid.

Core conformed by groups of pairs or by unit of groups of pairs. Filled core

Aluminum shield and double Jacket (inner and outer) in polyethylene type

moisture barrier.

Construction

Conductor

Soft copper wires

Insulation

Foam skin or solid high density polyethylene.

Twisted Pairs

Insulated conductors are twisted into pairs

Core Assembly

Up to 70 pairs, groups of 10 pairs, from 100 to 300 pairs groups of 25 pairs,

from 400 pairs and more, units of 100 pairs (each unit is conformed by 4 groups

of 25 pairs)

Spare pairs

One spare pair white-red colored at the interstices of each 100 pairs unit, to

guarantee nominal numbers of pairs.

Identification

Pairs, groups and units that conform the core, are identified by color code

(Attached)

Inner Jacket

Black polyethylene, abrasion, weather, and penetration to water resistant

(6)

Core Wrap

Non-hygroscopic dielectric tape. Offers dielectric strength between

core and sheath

Shield

Corrugated Aluminum tape both sides covered with copolymer

Outer Jacket

Black polyethylene, abrasion, weather, and penetration to water

resistant

Moisture Barrier

Filled Core with elastomeric compound, inner polyethylene jacket,

aluminum tape both sides covered with copolymer and outer

polyethylene external jacket, firmly bonded to external side of aluminum

tape.

Options

Manufacturing according to REA and/or Bellcore specifications

Shield in Flat Aluminum tape. Armor in corrugated and copolymer

covered Steel tape for direct buried and for rodent protection. Galvanized

steel wires armor for vertical installations. Other Core Assemblies are

available upon request.

Applications

Trunk cable and distribution cable networks. Special for wet locations;

the elastomeric compound filler prevents the entrance of moisture to

the core.

Trunk cable and distribution cable networks. Special for wet locations;

the elastomeric compound filler prevents the entrance of moisture to

the core.

The inner jacket offers additional blocking to the entrance of humidity

to the core, increases the dielectric strength pair-shield and improves

cable resistance to penetration of sharp objects.

CENTELSA Outside Telephone Cable, are able for voice and data

transmission up to 6.3 MHz, optimizing the bandwidth of copper cables.

(7)

Standards and Specifications

CENTELSA Outside Telephone Cable, are manufactured under the following

standards:

Standards:

ANSI/ICEA S-84-608 Telecommunications cable filled, polyolefin insulated

copper conductor.

NTC-2061 Telecommunications copper conductor multipair cables, polyolefin

insulated and covered, filled and dry.

Certifications

CENTELSA Outside Telephone Cable, are certified by:

ICONTEC (Colombia). Standard NTC 2061.

Note: Other configurations, sizes, colors and length not specified herein are

available upon request.

(8)

Outside Telephone Cable.

Filled Core. Moisture Barrier.

Foamed-Skin polyethylene insulation.

116 166 215 261 307 392 519 746 947 1341 1759 2144 2526 3712 4882 6057 7173 9390 143 216 283 350 415 539 729 1059 1354 1971 2552 3178 3751 5502 7254 8938 10686 14031 183 285 386 481 574 780 1059 1539 1977 2850 3754 4656 5504 8104 10690 13196 15775 20748 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.18 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.60 1.80 1.80 1.80 2.00 2.20 2.40 2.40 2.40 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.80 1.80 2.00 2.00 2.20 2.40 2.40 2.60 2.60 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.80 1.80 1.80 2.00 2.20 2.20 2.40 2.60 2.60 2.80 2.80 11.15 12.96 14.36 15.53 16.57 18.36 20.70 24.47 27.08 31.51 35.86 39.15 42.12 50.48 57.52 63.83 69.13 78.28 12.07 14.26 15.95 17.37 18.63 20.80 23.62 28.06 31.22 37.20 41.72 46.39 49.99 59.84 68.43 75.32 82.17 93.23 13.48 16.26 18.40 20.20 21.78 25.15 28.73 34.18 38.19 45.05 51.38 57.00 61.55 74.07 84.59 93.32 101.82 115.83 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 -1 2 2 3 4 5 6 9 12 15 18 24 -1 2 2 3 4 5 6 9 12 15 18 24 -1 2 2 3 4 5 6 9 12 15 18 24 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.80 0.80 0.80 0.90 0.90 0.90 1.00 1.10 1.20 1.20 1.20 0.70 0.70 0.70 0.70 0.70 0.70 0.70 0.80 0.80 0.90 0.90 1.00 1.00 1.10 1.20 1.20 1.30 1.30 0.70 0.70 0.70 0.70 0.70 0.80 0.80 0.90 0.90 0.90 1.00 1.10 1.10 1.20 1.30 1.30 1.40 1.40 NOMINAL PAIRS STANDARD LENGTH BY REEL (m) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) OVERALL DIAMETER (mm) SPARE PAIRS CONDUCTOR DIAMETER (mm) JACKET THICKNESS (mm) TOTAL WEIGTH (kg/km)

(9)

Outside Telephone Cable

Description

Soft copper wires insulated with high density polyethylene, foam skin or solid. Air

core, conformed by groups of pairs or by unit of groups of pairs. Aluminum shield and

external jacket in polyethylene type moisture barrier.

Construction

Conductor

Soft copper wires

Insulation

Foam skin or solid high density polyethylene.

Twisted Pairs

Insulated conductors are twisted into pairs

Core Assembly

Up to 70 pairs, groups of 10 pairs, from 100 to 300 pairs groups of 25 pairs, from 400

pairs and more, units of 100 pairs (each unit is conformed by 4 groups of 25 pairs)

Spare pairs

One spare pair white-red colored at the interstices of each 100 pairs unit, to guarantee

nominal numbers of pairs.

Identification

Pairs, groups and units that conform the core, are identified by color code (Attached)

Core Wrap

Non-hygroscopic dielectric tape. Offers dielectric strength between core and sheath

Shield

Corrugated Aluminum tape both sides covered with copolymer

Jacket

Black polyethylene, abrasion, weather, and penetration to water resistant

(10)

Moisture Barrier

Filled Core with elastomeric compound, aluminum tape both sides covered

with copolymer and polyethylene external jacket, firmly bonded to external

side of aluminum tape

Options

Manufacturing according to REA and/or Bellcore specifications

Shield in Flat Aluminum tape. Armor in corrugated and copolymer covered

Steel tape for direct buried and for rodent protection. Galvanized steel wires

armor for vertical installations. Other Core Assemblies are available upon

request.

Applications

Trunk cable and distribution cable networks. For use in pressurized networks.

Installation in ducts or raceways

CENTELSA Outside Telephone Cable, are able for voice and data transmission

up to 6.3 MHz, optimizing the bandwidth of copper cables.

Standards and Specifications

CENTELSA Outside Telephone Cable, are manufactured under the following

standards:

ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulated

copper conductor.

NTC-2061 Telecommunications copper conductor multipair cables, polyolefin

insulated and covered, filled and dry.

Certifications

CENTELSA Outside Telephone Cable, are certified by:

ICONTEC (Colombia). Standard NTC 2061.

Note: Other configurations, sizes, colors and length not specified herein

are available upon request.

(11)

Note: 1. Data herein indicated are approximated and are subject to normal manuracturing tolerances. 86 125 163 200 232 300 404 579 734 1047 1353 1678 1977 2908 3800 4716 5595 7438 108 164 217 270 318 419 566 823 1054 1541 1998 2478 2941 4323 5662 7040 8372 11070 133 214 288 361 433 587 801 1147 1478 2165 2829 3515 4164 6139 8113 10087 12004 15884 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.21 0.21 0.21 0.21 0.21 0.21 0.21 0.21 0.21 0.21 0.21 0.21 0.21 0.21 0.21 0.21 0.21 0.21 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.60 1.60 1.80 1.80 2.00 2.00 2.20 2.20 2.60 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.80 1.80 2.00 2.00 2.20 2.20 2.40 2.40 2.60 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.60 1.60 1.80 1.80 2.00 2.00 2.20 2.40 2.60 2.60 2.80 9.41 11.09 12.38 13.46 14.42 16.08 18.24 21.57 23.98 28.08 31.53 34.98 37.73 45.31 51.28 56.92 61.68 71.10 10.26 12.28 13.84 15.15 16.30 18.31 20.91 24.86 27.77 33.13 37.30 41.39 44.78 53.71 60.93 67.85 73.60 84.22 11.47 14.00 15.94 17.58 19.02 21.94 25.19 29.59 33.23 39.82 45.09 50.09 54.23 65.44 74.86 83.21 90.39 103.54 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 -1 2 2 3 4 5 6 9 12 15 18 24 -1 2 2 3 4 5 6 9 12 15 18 24 -1 2 2 3 4 5 6 9 12 15 18 24 NOMINAL PAIRS STANDARD LENGTH BY REEL (m) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) OVERALL DIAMETER (mm) SPARE PAIRS CONDUCTOR DIAMETER (mm) JACKET THICKNESS (mm)

Outside Telephone Cable.

Air Core. Moisture Barrier.

Foamed-Skin polyethylene insulation.

Standards: ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulated copper conductor. NTC-2061 Telecommunications copper conductor multipair cables, polyolefin insulated and covered, filled and dry.

(12)

Outside Telephone Cable.

Air Core. Moisture Barrier.

Solid polyethylene insulation.

Standards: ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulated copper conductor. NTC-2061 Telecommunications copper conductor multipair cables, polyolefin insulated and covered, filled and dry. 107 160 208 254 298 385 515 738 938 1334 1752 2138 2520 3694 4858 6024 7142 9417 137 213 284 352 418 548 742 1075 1378 2009 2605 3228 3818 5602 7383 9106 10882 14297 172 276 374 468 560 758 1034 1501 1933 2787 3670 4545 5380 7914 10442 12895 15414 20283 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.22 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.60 1.80 1.80 1.80 2.00 2.20 2.40 2.40 2.60 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.80 1.80 2.00 2.00 2.20 2.40 2.40 2.60 2.60 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.80 1.80 1.80 2.00 2.20 2.20 2.40 2.60 2.60 2.80 2.80 11.15 13.55 15.39 16.94 18.30 20.67 23.75 28.34 31.79 37.63 43.05 47.39 51.32 62.01 70.92 78.85 85.65 98.13 12.66 15.68 17.99 19.95 21.67 24.66 28.54 34.21 38.56 46.42 52.63 58.51 63.61 76.74 87.91 97.39 106.37 121.58 14.21 17.87 20.68 23.05 25.14 29.18 33.89 40.68 46.02 54.96 63.06 70.07 76.07 91.95 105.41 116.91 127.71 146.16 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 500 500 500 350 300 250 250 250 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2400 -1 2 2 3 4 5 6 9 12 15 18 24 -1 2 2 3 4 5 6 9 12 15 18 24 -1 2 2 3 4 5 6 9 12 15 18 24 NOMINAL PAIRS STANDARD LENGTH BY REEL (m) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) OVERALL DIAMETER (mm) SPARE PAIRS CONDUCTOR DIAMETER (mm) JACKET THICKNESS (mm)

(13)

Description

Soft copper wires insulated with high density polyethylene, foam skin or solid. Air

core, conformed by groups of pairs or by unit of groups of pairs. Aluminum shield,

support messenger and external jacket in polyethylene type moisture barrier.

Construction

Conductor

Soft copper wires

Insulation

Foam skin or solid high density polyethylene.

Twisted Pairs

Insulated conductors are twisted into pairs

Core Assembly

Up to 70 pairs, groups of 10 pairs, from 100 to 300 pairs groups of 25 pairs, from 400

pairs and more, units of 100 pairs (each unit is conformed by 4 groups of 25 pairs)

Spare pairs

One spare pair white-red colored at the interstices of each 100 pairs unit, to guarantee

nominal numbers of pairs.

Identification

Pairs, groups and units that conform the core, are identified by color code (Attached)

Core Wrap

Non-hygroscopic dielectric tape. Offers dielectric strength between core and sheath

Shield

Corrugated Aluminum tape both sides covered with copolymer

Support Messenger

7 Strand high strength galvanized steel wire.

Jacket

Black polyethylene, abrasion, weather, and penetration to water resistant

Outside Telephone Cable

Self-supported

(14)

Moisture Barrier

Air Core (for pressurerd systems) with elastomeric compound, aluminum

flat tape both sides covered with copolymer and polyethylene external jacket,

firmly bonded to external side of aluminum tape

Options

Manufacturing according to REA and/or Bellcore specifications

Shield in corrugated Aluminum tape. Filled Core. Galvanized steel wires

fully flooded for corrosion protection. Other Core Assemblies are available

upon request.

Applications

For pressured systems overhead trunk cable and distribution cable networks.

Aerial installation suspended from Messenger

CENTELSA Outside Telephone Cable, are able for voice and data transmission

up to 6.3 MHz, optimizing the bandwidth of copper cables.

Standards and Specifications

CENTELSA Outside Telephone Cable Figure 8, are manufactured under the

following standards:

ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulated

copper conductor.

NTC-2061 Telecommunications copper conductor multipair cables, polyolefin

insulated and covered, filled and dry.

Certifications

CENTELSA Outside Telephone Cable, are certified by:

ICONTEC (Colombia). Standard NTC 2061.

Note: Other configurations, sizes, colors and length not specified herein

are available upon request.

(15)

Outside Telephone Cable.

Figure 8. Air Core. Self Supported. Moisture Barrier.

Foamed-Skin polyethylene insulation.

Standards: ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulated copper conductor. NTC-2061 Telecommunications copper conductor multipair cables, polyolefin insulated and covered, filled and dry. 221 261 298 334 368 435 536 789 946 1256 242 298 352 403 453 552 780 1033 1266 1728 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.17 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.60 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.60 8.03 x 18.67 9.71 x 20.35 11.00 x 21.64 12.08 x 22.72 13.04 x 23.68 14.70 x 25.34 16.86 x 27.50 20.19 x 32.15 22.61 x 34.57 26.70 x 38.66 8.88 x 19.52 10.90 x 21.54 12.46 x 23.10 13.77 x 24.41 14.93 x 25.57 16.93 x 27.57 19.54 x 31.50 23.48 x 35.44 26.39 x 38.35 31.34 x 43.30 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 10 20 30 40 50 70 100 150 200 300 10 20 30 40 50 70 100 150 200 300 -1 2 2 3 -1 2 2 3 1.57 1.57 1.57 1.57 1.57 1.57 1.57 2.03 2.03 2.03 1.57 1.57 1.57 1.57 1.57 1.57 2.03 2.03 2.03 2.03 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 NOMINAL PAIRS STANDARD LENGTH BY REEL (m) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) EXTERNAL DIMENSIONS (mm) SPARE PAIRS CONDUCTOR DIAMETER (mm) JACKET THICKNESS (mm) MESSENGER STRANDS No. DIAMETER (mm)

(16)

Outside Telephone Cable.

Figure 8. Air Core. Self Supported. Moisture Barrier.

Solid polyethylene insulation.

Standards: ANSI/ICEA S-85-625 Telecommunications cable aircore, polyolefin insulated copper conductor. NTC-2061 Telecommunications copper conductor multipair cables, polyolefin insulated and covered, filled and dry. 222 263 300 336 371 439 543 799 959 1277 246 305 361 414 467 570 805 1071 1315 1800 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.19 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.60 1.40 1.40 1.40 1.40 1.40 1.40 1.40 1.60 1.60 1.60 8.03 x 18.67 9.71 x 20.35 11.00 x 21.64 12.08 x 22.72 13.04 x 23.68 14.70 x 25.34 16.86 x 27.50 20.19 x 32.15 22.61 x 34.57 26.70 x 38.66 9.10 x 19.74 11.22 x 21.86 12.85 x 23.49 14.22 x 24.86 15.43 x 26.07 17.52 x 28.16 20.25 x 32.21 24.35 x 36.31 27.40 x 39.36 32.57 x 44.53 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 1500 1500 1500 1500 1500 1500 1000 1000 1000 750 10 20 30 40 50 70 100 150 200 300 10 20 30 40 50 70 100 150 200 300 -1 2 2 3 -1 2 2 3 1.57 1.57 1.57 1.57 1.57 1.57 1.57 2.03 2.03 2.03 1.57 1.57 1.57 1.57 1.57 1.57 2.03 2.03 2.03 2.03 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 NOMINAL PAIRS STANDARD LENGTH BY REEL (m) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) EXTERNAL DIMENSIONS (mm) SPARE PAIRS CONDUCTOR DIAMETER (mm) JACKET THICKNESS (mm) MESSENGER STRANDS No. DIAMETER (mm)

(17)

Description

Drop Wire Paralleled. Hard copper conductors or steel copper covered,

polyethylene or PVC insulated.

Construction

Conductor

Hard copper or steel copper covered (CCS)

Insulation

Single layer Polyethylene for PE and insulation – jacket integral for

DWP-2PE, weather resistant.

Polyethylene Insulation and PVC jacket for DWP PE-PVC.

Flame retardant PVC for DWP-PVC.

Paralleled conductors with polarization ridge and conductor separator membrane.

Application

Self supporting one pair parallel conductor Drop Wire intended for aerial service

connection to the subscriber

Standards

CENTELSA telephone wires DWP are manufactured under the following

standards:

NTC 1300 Service Drop telephone wire, inside installations and jumper.

Certifications

CENTELSA Outside Telephone Wire, are certified by:

CIDET (Colombia). Standard NTC 1300.

Package

100 or 200 meters spools in corrugated carton boxes

Note: other configurations and sizes not specified in this catalogue are available

upon request.

Outside Telephone

Wire DWP

(18)

Outside Telephone Wire (International System Unit)

Drop Wire Parallel

Standards: NTC 1300 Service Drop telephone wire,

inside installations and jumper.

Outside Telephone Wire (International System Unit)

Drop Wire Parallel

Standards: NTC 1300 Service Drop telephone wire,

inside installations and jumper.

0.80 0.80 0.80 0.80 0.80 1.50 MATERIAL AISLAMIENTO

Notes: 1. DC resistance calculated based on a 10.785 ohm-cmil/ft resistivity for Hard cooper and 33.91 ohm-cmil/ft for steel copper covered. 2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.

Hard Copper Hard Copper Copper Clad Steel Copper Clad Steel Hard Copper Hard Copper Hard Copper Hard Copper Hard Copper 2 x 18 DWP PVC APPROX. TOTAL WEIGTH (kg/km) INSULATION MATERIAL EXTERNAL DIMENSIONS (mm) DC RESISTANCE AT 20° C1 (ohm/km) INSULATION RESISTANCE (Mohm-km) TYPE CONDUCTOR CROSS SECTION (mm2) INSULATION THICKNESS (mm) ONE CONDUCTOR TENSILE STRENGTH (Nominal) (MPa) JACKET THICKNESS (mm) SIZE No. x AWG SEPARATOR (mm) STRAND DIAMETER (mm) DWP PE CCS DWP PVC CCS 2 x 18 2 x 20 2 x 18 2 x 18 2 x 20 DWP PE 2 x 18 2 x 18 2 x 20 DWP 2PE DWP PE-PVC 2 x 18 2 x 18 2 x 20 2 x 18 2 x 18 2 x 20 2 x 18 2 x 18 2 x 20 1.02 1.02 0.81 1.02 1.02 0.81 1.02 1.02 0.81 0.82 0.82 0.52 0.82 0.82 0.52 0.82 0.82 0.52 PE PVC PVC PVC PE PE PE PE PE 0.80 0.80 0.80 0.80 0.80 0.80 1.60 0.70 0.70 1.00 1.00 1.00 1.00 1.00 1.00 -0.80 0.80 2.62 x 6.25 2.62 x6.25 2.41 x 5.83 2.62 x 6.25 2.62 x 6.25 2.41 x 5.83 4.22 x 7.17 4.02 x 8.05 3.81 x 7.63 23 29 22 28 24 18 36 49 40 72.6 22.2 35.2 72.6 22.2 35.2 22.2 22.2 35.2 6229 249 288 249 6229 7202 7167 362 409 875 460 473 875 460 473 460 460 473

Notas: 1. DC resistance calculated based on a 17.93 ohm-mm2/km resistivity for Hard cooper and 58.62 ohm-mm2/km for steel copper covered. 2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.

Hard Copper Hard Copper Copper Clad Steel Copper Clad Steel Hard Copper Hard Copper Hard Copper Hard Copper Hard Copper 2 x 18 DWP PVC APPROX. TOTAL WEIGTH (pound/kft) INSULATION MATERIAL EXTERNAL DIMENSIONS (mils) DC RESISTANCE AT 20° C1 (ohm/kft) INSULATION RESISTANCE (Mohm/kft) TYPE CONDUCTOR CROSS SECTION (kcmil) INSULATION THICKNESS (mils) ONE CONDUCTOR TENSILE STRENGTH (Nominal) (ksi) JACKET THICKNESS (mils) SIZE No. x AWG SEPARATOR (mils) STRAND DIAMETER (mils) DWP PE CCS DWP PVC CCS 2 x 18 2 x 20 2 x 18 2 x 18 2 x 20 DWP PE 2 x 18 2 x 18 2 x 20 DWP 2PE DWP PE-PVC 2 x 18 2 x 18 2 x 20 2 x 18 2 x 18 2 x 20 2 x 18 2 x 18 2 x 20 40 40 32 40 40 32 40 40 32 1.63 1.63 1.02 1.63 1.63 1.02 1.63 1.63 1.02 PE PVC PVC PVC PE PE PE PE PE 31 31 31 31 31 31 63 28 28 39 39 39 39 39 39 -31 31 103 x 246 103 x 246 95 x 229 103 x 246 103 x 246 95 x 229 166 x 282 158 x 317 150 x 300 15 20 15 19 16 12 25 33 27 22.1 6.77 10.7 22.1 6.77 10.7 6.77 6.77 10.7 6229 817 944 817 20437 23628 23514 1188 1342 875 67 69 127 67 69 67 67 69

(19)

Outside Telephone

Wire DWT

Drop Wire Twisted

Description

Drop Wire Twisted. Hard copper conductor, individually insulated with polyethylene

or PVC.

Construction

Conductor

Hard copper

Insulation

Black Polyethylene weather resistant or flame retardat PVC.

Application

Self supporting one pair twisted conductor Drop Wire intended for aerial service

connection to the subscriber

Standards

CENTELSA telephone wires DWT are manufactured under the following standards:

NTC 1300 Service Drop telephone wire, inside installations and jumper.

Certifications

CENTELSA Outside Telephone Wire, are certified by:

CIDET (Colombia). Standard NTC 1300.

Package

100 or 200 meters spools in corrugated carton boxes

Note: other configurations and sizes not specified in this catalogue are available

upon request.

(20)

Outside Telephone Wire (International System Unit)

Drop Wire Twisted

Standards: NTC 1300 Service Drop telephone wire,

inside installations and jumper.

0.82 0.52 0.82 0.52 2 x 18 2 x 20 2 x 18 2 x 20 DWT PVC DWT PVC DWT PE DWT PE 1.02 0.81 1.02 0.81 249 288 6229 7202 22.7 35.9 22.7 35.9 28 21 23 17 460 473 460 473 0.80 0.80 0.80 0.80 2.62 2.41 2.62 2.41 5.25 4.83 5.25 4.83 APPROX. TOTAL WEIGTH (kg/km) CROSS SECTION (mm2) EXTERNAL DIAMETER (mm) DC RESISTANT AT 20°C1 (ohm/km) INSULATION RESISTANCE (Mohm-km) TYPE SIZE No. x AWG STRAND DIAMETER (mm) ONE CONDUCTOR TENSILE STRENGTH (Nominal) (MPa) INSULATION THICKNESS (mm) DIAMETER OVER INSULATION (mm)

Notes: 1. DC resistance calculated based on a 10.785 ohm-cmil/ft resistivity for Hard cooper. 2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.

Outside Telephone Wire

Drop Wire Twisted

Standards: NTC 1300 Service Drop telephone wire,

inside installations and jumper.

1.63 1.02 1.63 1.02 2 x 18 2 x 20 2 x 18 2 x 20 DWT PVC DWT PVC DWT PE DWT PE 40 32 40 32 817 944 20437 23628 6.90 11.0 6.90 11.0 19 14 16 11 67 69 67 69 31 31 31 31 103 95 103 95 207 190 207 190 APPROX. TOTAL WEIGTH (pound/kft) CROSS SECTION (kcmil) EXTERNAL DIAMETER (mils) DC RESISTANT AT 20°C1 (ohm/kft) INSULATION RESISTANCE (Mohm-kft) TYPE SIZE No. x AWG STRAND DIAMETER (mils) ONE CONDUCTOR TENSILE STRENGTH (Nominal) (ksi) INSULATION THICKNESS (mils) SEPARATOR (mils)

Notes: 1. DC resistance calculated based on a 17.93 ohm-mm2/km resistivity for Hard cooper. 2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.

(21)

Description

Soft copper wires insulated with flame retardant PVC, paired, unshielded or shielded

with aluminum foil and drain wire, external PVC jacket.

Construction

Conductor

Soft copper

Insulation

Flame retardant PVC

Pairs

Two insulated conductor twisted together

Core

Up to 25 pairs one group of pairs, for 30 pairs and more, groups of 10 or 25 pairs.

Spare pairs

One pair color coded White-Red for 10 pairs or more.

Identification

Pairs, groups an units in the assembly core, are identified by color code (included

in this catalogue)

Core Wrap

Non hygroscopic polyester tape

Shield

Unshielded or shielded with aluminum foil and tinned copper drain wire

Jacket

Flame retardant PVC, gray colored.

Characteristics

Mutual capacitance

120 nF/km.

Capacitive Unbalance

400 pF (referred to 500 m).

(22)

DC Conductor Resistance

97.8 ohm/km.

Maximum Operating Voltage

60 V.

Insulation Resistance

500 Mohm-km.

Dielectric Strength (60 seg)

1000 V AC, 1500 V DC.

Applications

For inside residential commercial and industrial applications. Appropriate

for locations with electric interference produced by near power electric circuit.

Installation in dry locations in ducts trays and race ways.

Standards

CENTELSA Inside Cables are manufactured under the following standards:

NTC-983, IEC 189. Cables e hilos para bajas frecuencias con aislamiento

y cubierta en PVC.

Notes:

1. Optionally with tinned copper conductor

2. Other configurations and sizes not specified in this catalogue

are available upon request.

(23)

Note: Data herein indicated are approximate and are subject to normal manufacturing tolerances.

Inside Unshielded Telephone Cable

Standards:

Low Frecuency Cables and Wire with PVC Insulation and PVC Sheat.

NOMINAL PAIRS STANDARD LENGTH BY REEL (m) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) OVERALL DIAMETER (mm) SPARE PAIRS CONDUCTOR DIAMETER (mm) JACKET THICKNESS (mm) 15 22 28 34 40 49 79 139 168 200 255 310 424 584 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.60 0.60 0.60 0.60 0.60 0.70 0.70 0.80 0.80 0.90 0.90 0.90 1.00 1.00 3.18 3.93 4.50 4.98 5.40 6.00 7.26 9.46 10.32 11.32 12.72 13.95 16.31 19.03 100 1000 1000 1000 1000 1000 2000 2000 2000 2000 1500 1000 1000 1000 1 2 3 4 5 6 10 20 25 30 40 50 70 100 -1 1 1 1 1 1 1 1

Note: Data herein indicated are approximate and are subject to normal manufacturing tolerances.

Inside Unshielded Telephone Cable

Standards:

Low Frecuency Cables and Wire with PVC Insulation and PVC Sheat.

16 23 30 36 42 51 81 142 171 204 259 314 429 590 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.60 0.60 0.60 0.60 0.60 0.70 0.70 0.80 0.80 0.90 0.90 0.90 1.00 1.00 3.36 4.11 4.68 5.16 5.58 6.18 7.44 9.64 10.50 11.50 12.90 14.13 16.49 19.21 100 1000 1000 1000 1000 1000 2000 2000 2000 2000 1500 1000 1000 1000 1 2 3 4 5 6 10 20 25 30 40 50 70 100 -1 1 1 1 1 1 1 1 NOMINAL PAIRS STANDARD LENGTH BY REEL (m) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) OVERALL DIAMETER (mm) SPARE PAIRS CONDUCTOR DIAMETER (mm) JACKET THICKNESS (mm)

(24)

Description

Twisted pair for cross connections, for inside use. Soft tinned copper insulated

with PVC or PVC and Nylon, assembly in pairs, triads or quads.

Construction

Conductor

Soft tinned copper wire

Insulation

Flame retardant PVC for JWT.

Flame retardant PVC insulation; abrasion oil and gasoline resistant Nylon

jacket for JWT PVC-NY.

Applications

JWT: twisted telephone wire for inside use, cross connections, telephonic

derivations and radio and TV equipment wiring.

JWT PVC-NY: connection wire in distributors, mini-distributors and telephonic

equipment. Nylon jacket provides abrasion resistance.

JWT NY: connection wire in distributors, mini-distributors and telephonic

equipment.

Radio and TV equipment wiring, weld able without remove the insulation,

Diameter reduced tightness and low friction advantages given by Nylon

insulation. Installation in dry locations, ducts or open installation.

Standards

CENTELSA telephone wires JWT are manufactured under the following

standards:

NTC 1300 Service Drop telephone wire, inside installations and jumper.

Inside Telephone

Wire JWT

(25)

Certifications

CENTELSA Outside Telephone Wire, are certified by:

CIDET (Colombia). Standard NTC 1300.

Package

100 or 200 meters spools in corrugated carton boxes

Note: other configurations and sizes not specified in this catalogue are available

upon request.

Notes: 1. DC resistance calculated based on a 17.93 ohm-mm2/km resistivity for Tinned cooper. 2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.

Inside Telephone Wire JWT PVC

(International System Units)

Jumper Wire Twisted PVC

Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.

0.32 0.32 0.32 0.21 0.21 0.21 0.28 0.28 0.28 0.20 0.20 0.20 2 x 22 3 x 22 4 x 22 2 x 24 3 x 24 4 x 24 2 x 0.6 3 x 0.6 4 x 0.6 2 x 0.5 3 x 0.5 4 x 0.5 0.64 0.64 0.64 0.51 0.51 0.51 0.60 0.60 0.60 0.50 0.50 0.50 174 174 174 180 180 180 183 183 183 183 183 183 57.4 57.4 57.4 91.0 91.0 91.0 66.0 66.0 66.0 95.0 95.0 95.0 8.4 12.6 16.8 5.4 8.1 10.9 7.6 11.3 15.1 5.2 7.9 10.5 0.30 0.30 0.30 0.25 0.25 0.25 0.30 0.30 0.30 0.25 0.25 0.25 1.24 1.24 1.24 1.01 1.01 1.01 1.20 1.20 1.20 1.00 1.00 1.00 2.49 2.68 3.00 2.02 2.18 2.44 2.40 2.59 2.90 2.00 2.16 2.41 SIZE AWG or mm DC RESISTANCE AT 20° C¹ (ohm/km) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) OVERALL DIAMETER (mm) STRAND DIAMETER (mm) CROSS SECTION (mm²) EXTERNAL DIAMETER (mm) INSULATION RESISTANCE (Mohm/km)

(26)

Inside Telephone Wire JWT PVC-NY

Jumper Wire Twisted PVC-Nylon

Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.

Notes: 1. DC resistance calculated based on a 10.785 ohm-cmil/ft resistivity for Tinned cooper. 2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.

0.25 0.40 0.64 2 x 26 2 x 24 2 x 22 15.9 20.1 25.3 126 108 91 44.4 27.7 17.5 2.6 3.7 5.3 4.3 4.3 4.3 38.0 42.2 47.4 75.9 84.3 94.7 6.7 6.7 6.7 29.3 33.5 38.7

Inside Telephone Wire JWT PVC-NY

(International System Units)

Jumper Wire Twisted PVC-Nylon

Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.

APPROX. TOTAL WEIGTH (kg/km) CROSS SECTION (mm2) EXTERNAL DIAMETER (mm) DC RESISTANCE AT 20°C1 (ohm/km) INSULATION RESISTANCE (Mohm-km) SIZE AWG or mm STRAND DIAMETER (mm) JACKET THICKNESS (mm) DIAMETER OVER JACKET (mm) NSULATION THICKNESS (mm) DIAMETER OVER INSULATION (mm) 0.13 0.21 0.32 0.13 0.20 0.28 2 x 26 2 x 24 2 x 22 2 x 0.4 2 x 0.5 2 x 0.6 0.40 0.51 0.64 0.40 0.50 0.60 39 33 28 39 33 29 146 91.0 57.4 148 95.0 66.0 3.8 5.5 7.9 3.8 5.3 7.1 0.11 0.11 0.11 0.11 0.11 0.11 0.96 1.07 1.20 0.96 1.06 1.16 1.93 2.14 2.41 1.92 2.12 2.32 0.17 0.17 0.17 0.17 0.17 0.17 0.74 0.85 0.98 0.74 0.84 0.94

Inside Telephone Wire JWT PVC

Jumper Wire Twisted PVC

Standards: NTC 1300 Service Drop telephone wire, inside installations and

jumper.

0.64 0.64 0.64 0.40 0.40 0.40 2 x 22 3 x 22 4 x 22 2 x 24 3 x 24 4 x 24 25 25 25 20 20 20 572 572 572 592 592 592 17.5 17.5 17.5 27.7 27.7 27.7 5.7 8.5 11.3 3.6 5.5 7.3 11.8 11.8 11.8 9.8 9.8 9.8 48.9 48.9 48.9 39.8 39.8 39.8 97.9 105.5 118.1 79.6 85.8 96.1 SIZE AWG or mm DC RESISTANCE AT 20° C¹ (ohm/kft) INSULATION THICKNESS (mils) APPROX. TOTAL WEIGTH (pound/kft) OVERALL DIAMETER (mils) STRAND DIAMETER (mils) CROSS SECTION (sq inches) EXTERNAL DIAMETER (mils) INSULATION RESISTANCE (Mohm/kft) APPROX. TOTAL WEIGTH (kg/km) CROSS SECTION (sq inches) EXTERNAL DIAMETER (mils) DC RESISTANCE AT 20°C1 (ohm/km) INSULATION RESISTANCE (Mohm-km) SIZE AWG or mm STRAND DIAMETER (mils) JACKET THICKNESS (mils) DIAMETER OVER JACKET (mils) NSULATION THICKNESS (mils) DIAMETER OVER INSULATION (mils)

(27)

Inside Telephone Wire JWT NY

(International System Units)

Jumper Wire Twisted PVC-Nylon

Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.

0.13 0.21 0.32 0.13 0.20 0.28 2 x 26 2 x 24 2 x 22 2 x 0.4 2 x 0.5 2 x 0.6 0.40 0.51 0.64 0.40 0.50 0.60 10 10 10 10 10 10 146 91.0 57.4 148 95.0 66.0 3.0 4.5 6.8 3.0 4.3 6.0 0.17 0.17 0.17 0.17 0.17 0.17 0.74 0.85 0.98 0.74 0.84 0.94 1.49 1.83 2.37 1.48 1.81 2.27

Inside Telephone Wire JWT NY

Jumper Wire Twisted PVC-Nylon

Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.

Notes: 1. DC resistance calculated based on a 10.785 ohm-cmil/ft resistivity for Tinned cooper. 2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.

0.25 0.40 0.64 2 x 26 2 x 24 2 x 22 15.9 20.1 25.3 33 33 33 44.4 27.7 17.5 2.0 3.0 4.6 6.7 6.7 6.7 29.3 33.5 38.7 58.6 72.2 93.4 SIZE AWG or mm DC RESISTANCE AT 20° C¹ (ohm/km) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) DIAMETER OVER INSULATION (mm) STRAND DIAMETER (mm) CROSS SECTION (mm²) EXTERNAL DIAMETER (mm) INSULATION RESISTANCE (Mohm/km) SIZE AWG or mm DC RESISTANCE AT 20° C¹ (ohm/kft) INSULATION THICKNESS (mils) APPROX. TOTAL WEIGTH (pound/kft) DIAMETER OVER INSULATION (mils) STRAND DIAMETER (mils) CROSS SECTION (sq inches) EXTERNAL DIAMETER (mils) INSULATION RESISTANCE (Mohm/kft)

(28)

Description

Inside drop wire paralleled. Soft copper insulated with PVC.

Construction

Conductor

Soft copper wire

Insulation

Flame retardant white PVC, paralleled conductors with polarization ridge.

Applications

Paralleled telephone wire for inside use from the interior box to exterior box;

telephonic derivations.

Installation in dry locations, ducts or open installation.

Standards

CENTELSA telephone wires JWP are manufactured under the following

standards:

NTC 1300 Service Drop telephone wire, inside installations and jumper.

Certifications

CENTELSA Outside Telephone Wire, are certified by:

CIDET (Colombia). Standard NTC 1300.

Package

100 or 200 meters spools in corrugated carton boxes

Note: other configurations and sizes not specified in this catalogue are

available upon request.

Inside Telephone

Wire JWP

(29)

Notes: 1. DC resistance calculated based on a 17.241 ohm-mm2/km resistivity for Soft cooper. 2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.

Inside Telephone Wire JWP

(International System Units)

Jumper Wire Parallel

Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.

0.52 0.32 2 x 20 2 x 22 0.81 0.64 240 279 33.9 54.2 18.1 13.5 0.60 0.60 2.01 x 4.03 1.84 x 3.69

Notes: 1. DC resistance calculated based on a 10.371 ohm-cmil/ft resistivity for Soft cooper. 2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.

1.02 0.64 2 x 20 2 x 22 32.0 25.3 787 914 10.3 16.5 12.2 9.1 23.6 23.6 79.3 x 158.5 72.6 x 145.1

Inside Telephone Wire JWP

Jumper Wire Parallel

Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.

SIZE AWG or mm DC RESISTANCE AT 20° C¹ (ohm/km) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) STRAND DIAMETER (mm) CROSS SECTION (mm²) EXTERNAL DIAMETER (mm) INSULATION RESISTANCE (Mohm/km) SIZE AWG or mm DC RESISTANCE AT 20° C¹ (ohm/kft) INSULATION THICKNESS (mils) APPROX. TOTAL WEIGTH (pound/kft) STRAND DIAMETER (mm) CROSS SECTION (kcmil) EXTERNAL DIAMETER (mils) INSULATION RESISTANCE (Mohm/kft)

(30)

Description

Inside drop wire paralleled. Soft copper insulated with PVC.

Construction

Conductor

Soft copper wire

Insulation

Flame retardant white PVC, paralleled conductors with polarization ridge.

Applications

Paralleled telephone wire for inside use from the interior box to exterior box;

telephonic derivations.

Installation in dry locations, ducts or open installation.

Standards

CENTELSA telephone wires JWP are manufactured under the following

standards:

NTC 1300 Service Drop telephone wire, inside installations and jumper.

Certifications

CENTELSA Outside Telephone Wire, are certified by:

CIDET (Colombia). Standard NTC 1300.

Package

100 or 200 meters spools in corrugated carton boxes

Note: other configurations and sizes not specified in this catalogue are

available upon request.

Inside Telephone

Wire JWP

(31)

Notes: 1. DC resistance calculated based on a 17.241 ohm-mm2/km resistivity for Soft cooper. 2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.

Inside Telephone Wire JWP

(International System Units)

Jumper Wire Parallel

Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.

0.52 0.32 2 x 20 2 x 22 0.81 0.64 240 279 33.9 54.2 18.1 13.5 0.60 0.60 2.01 x 4.03 1.84 x 3.69

Notes: 1. DC resistance calculated based on a 10.371 ohm-cmil/ft resistivity for Soft cooper. 2. Data herein indicated are approximate and are subject to normal manufacturing tolerances.

1.02 0.64 2 x 20 2 x 22 32.0 25.3 787 914 10.3 16.5 12.2 9.1 23.6 23.6 79.3 x 158.5 72.6 x 145.1

Inside Telephone Wire JWP

Jumper Wire Parallel

Standards: NTC 1300 Service Drop telephone wire, inside installations and jumper.

SIZE AWG or mm DC RESISTANCE AT 20° C¹ (ohm/km) INSULATION THICKNESS (mm) APPROX. TOTAL WEIGTH (kg/km) STRAND DIAMETER (mm) CROSS SECTION (mm²) EXTERNAL DIAMETER (mm) INSULATION RESISTANCE (Mohm/km) SIZE AWG or mm DC RESISTANCE AT 20° C¹ (ohm/kft) INSULATION THICKNESS (mils) APPROX. TOTAL WEIGTH (pound/kft) STRAND DIAMETER (mm) CROSS SECTION (kcmil) EXTERNAL DIAMETER (mils) INSULATION RESISTANCE (Mohm/kft)

(32)

Electrical Characteristics

Outside Telephone Cables

MUTUAL CAPACITANCE (nF/km) SIZE (mm) Nominal1 Maximum average Maximum individual 0.4 52 55 64 0.5 52 55 64 0.6 52 55 64 Conductor DC Resistance (ohm/km) SIZE (mm) Maximum average Maximum individual 0.4 144.0 150.0 0.5 92.1 95.9 0.6 63.9 66.6 RESISTIVE UNBALANCE1 (%) SIZE (mm) Maximum average Maximum individual 0.4 2.0 5.0 0.5 1.5 5.0 0.6 1.5 4.0 1500 5000 INSULATION RESISTANCE (Mohm-km)

Filled Core Air Core

Conductor A vs Conductor B Conductor vs Shield 2000V, 3s 1000V, 60s 6000V, 3s 3000V, 60s 1000V, 3s 500V, 60s 2000V, 3s 1000V, 60s DIELECTRIC STRENGTH (Volts) SOLID POLYETHYLENE FOAM SKIN POLYETHYLENE MAXIMUM AVERAGE ATENUATION1 (db/km) SIZE (mm) A 1000 Hz A 150 kHz A 772 kHz 0.4 1.88 12.1 23.0 0.5 1.51 8.90 18.4 0.6 1.26 6.90 15.5

Notes: 1. Test or value not indicated in Standard NTC 2061. 2. Data herein indicated are subject to normal tolerances.

Pair to pair (pF refered to 500m) Pair to shield1 (pF/km) 250 2625 150 -CAPACITIVE UNBALANCE (pF refered to 500m) INDIVIDUAL VALUE 95% OF VALUES

CROSSTALK Power Sum dB/305m ELFEXT 150 772 1600 3150 6300 0.4 mm 61 47 41 35 29 0.5 mm 63 49 42 37 31 0.6 mm 63 49 43 37 31 0.4, 0.5 and 0.6 mm 57 43 37 31 25 Average Average Frequency kHz 0.4, 0.5 and 0.6 mm 58 47 43 38 34 0.4, 0.5 and 0.6 mm 53 42 38 33 29 ELNEXT

(33)

Pairs Codes in 25 Pairs Groups

Inside¹ and Outside Telephone Cables

1 2 3 4 5 6 7 8 9 10 WHITE WHITE WHITE WHITE WHITE RED RED RED RED RED BLUE ORANGE GREEN BROWN GREY BLUE NARANJA GREEN BROWN GREY

PAIR No. INSULATION COLOR

CONDUCTOR A CONDUCTOR B

10 PAIRS GROUP COLOR CODE

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 WHITE WHITE WHITE WHITE WHITE RED RED RED RED RED BLACK BLACK BLACK BLACK BLACK YELLOW YELLOW YELLOW YELLOW YELLOW PURPLE PURPLE PURPLE PURPLE PURPLE BLUE ORANGE GREEN BROWN GREY BLUE ORANGE GREEN BROWN GREY BLUE ORANGE GREEN BROWN GREY BLUE ORANGE GREEN BROWN GREY BLUE ORANGE GREEN BROWN GREY

PAIR No. INSULATION COLOR

CONDUCTOR A CONDUCTOR B

PAIRS CODES IN 25 PAIRS GROUPS

CONSTRUCTION GROUP No. PAIRS

GROUP IDENTIFICATION BINDER COLOR 10 PAIR GROUPS 25 PAIR GROUPS 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 10 11 12 1 to 10 11 to 20 21 to 30 31 to 40 41 to 50 51 to 60 61 to 70 1 to 25 26 to 50 51 to 75 76 to 100 101 to 125 126 to 150 151 to 175 176 to 200 201 to 225 226 to 250 251 to 275 276 to 300 WHITE - BLUE WHITE - ORANGE WHITE - GREEN WHITE - BROWN WHITE- GREY RED - BLUE RED - ORANGE WHITE - BLUE WHITE - ORANGE WHITE - GREEN WHITE - BROWN WHITE- GREY RED - BLUE RED - ORANGE RED - GREEN RED - BROWN RED - GREY BLACK - BLUE BLACK - ORANGE Note: 1. Specifications for inside telephone cables up to 100 pairs.

(34)

Unit Color Code Identification

Outside Telephone Cables

25 PAIRS 1 2 3 4 WHITE - BLUE WHITE - ORANGE WHITE - GREEN WHITE - BROWN

CONSTRUCTION GROUP No. BINDER COLOR

IDENTIFICATION FOR 4 GROUPS IN 100 PAIRS UNITS

CONSTRUCTION UNIT No. BINDER COLOR

UNITS IDENTIFICATION PAIRS 100 PAIRS UNIT (4 GROUPS OF 25 PAIRS EACH) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 WHITE - BLUE WHITE - ORANGE WHITE - GREEN WHITE - BROWN WHITE - GREY RED - BLUE RED - ORANGE RED - GREEN RED - BROWN RED - GREY BLACK - BLUE BLACK - ORANGE BLACK - GREEN BLACK - BROWN BLACK - GREY YELLOW - BLUE YELLOW - ORANGE YELLOW - GREEN YELLOW - BROWN YELLOW - GREY PURPLE - BLUE PURPLE - ORANGE PURPLE - GREEN PURPLE - BROWN 1 to 100 101 to 200 201 to 300 301 to 400 401 to 500 501 to 600 601 to 700 701 to 800 801 to 900 901 to 1000 1001 to 1100 1101 to 1200 1201 to 1300 1301 to 1400 1401 to 1500 1501 to 1600 1601 to 1700 1701 to 1800 1801 to 1900 1901 to 2000 2001 to 2100 2101 to 2200 2201 to 2300 2301 to 2400

(35)

PAIRS ASSEMBLY GROUPS BY UNIT CORE ASSEMBLY IN GROUPS OR UNITS

PAIRS BY GROUP 10 20 30 40 50 70 100 150 200 300 400 500 600 900 1200 1500 1800 2100 2400 (0+1) (0+2) (0+3) (0+4) (0+5) (1+6) (0+4) (1+5) (2+6) (3+9) (0+4) (0+5) (1+5) (2+7) (3+9) (1+5+9) (2+6+10) (2+8+11) (2+8+14) 10 10 10 10 10 10 25 25 25 25 25 25 25 25 25 25 25 25 25 GROUPS GROUPS GROUPS GROUPS GROUPS GROUPS GROUPS GROUPS GROUPS GROUPS UNITS UNITS UNITS UNITS UNITS UNITS UNITS UNITS UNITS -4 4 4 4 4 4 4 4 4

Unit Color Code Identification

Outside Telephone Cables

(36)

Assembly and Identification

for Multipair Telephone Cable Core

Inside¹ and Outside Telephone Cables

20 Pairs Assembly (0+2)

20 to 70 pairs 10 PAIRS GROUP CABLES

White Orange White Blue 50 Pairs Assembly (0+5) White Grey White Blue White Green White Orange White Brown 40 Pairs Assembly (0+4) White Brown White Blue White Green White Orange 30 Pairs Assembly (0+3) White Green White Blue White Orange 70 Pairs Assembly (1+6) Red Blue White Orange White Grey Blanco Verde Red Orange White Brown White Blue 100 Pairs Assembly (0+4) 100 to 300 pairs 25 PAIRS GROUP CABLES

White Brown White Blue White Green White Orange 200 Pairs Assembly (2+6) Red Orange White Green Red Blue White Brown Red Green White Grey White Orange White Blue 300 Pairs Assembly (3+9) Red Grey White Brown Red Green White Grey Black Blue Red Blue White Green White Blue White Orange Black Orange Red Orange Red Brown 150 Pairs Assembly (1+5) White Orange White Grey _White Green Red Blue White Brown White Blue

(37)

1500 Pairs Assembly (1+5+9)

400 Pairs Assembly (0+4)

400 to 2400 pairs 100 PAIRS UNIT CABLES (EACH UNIT 4 GROUPS OF 25 PAIRS)

White Blue White Orange White Green White Brown 2100 Pairs Assembly (2+8+11) 2400 Pairs Assembly (2+8+14) 1800 Pairs Assembly (2+6+10) 1200 Pairs Assembly (3+9) Rojo Gris White Brown Red Green White Grey Black Blue Red Blue White Green White Blue White Orange Black Orange Red Orange Red Brown 900 Pairs Assembly (2+7) Red Green White Green White Brown Red Blue White Grey White Orange White Blue Red Brown Red Orange 600 Pairs Assembly (1+5) White Grey White Orange White Green Red Blue White Brown White Blue 500 Pairs Assembly (0+5) White Grey White Blue White Green White Orange White Brown White Grey White Orange White Green Red Blue White Brown White Blue Black Grey Red Orng Red Green Red Brown Red Grey Black Blue Black Orng Black Green Black Brown Yellow Green Red Brown Red Grey Black Blue Black Orange Black Green Black Grey Yellow Blue Yellow Orange Red Orange White Green Red Blue White Brown Red Green White Grey White Orange White Blue Black Brown Purple Blue Black Blue Black Orange Black Green Black Brown Black Grey Yellow Green Yellow Brown Yellow Grey Red Green White Green Red Orange White Brown Red Brown Red Blue White Orange White Blue Yellow Blue White Grey Red Grey Yellow Orange Purple Brown Black Blue Black Orange Orange Green Black Grey Yellow Blue Yellow Grey Purple Blue Purple Orange Red Green White Green Red Orange White Brown Red Brown Red Blue White Orange White Blue Yellow Green White Grey Red Grey Yellow Brown Yellow Orange Black Brown Purple Green

Assembly and Identification

for Multipair Telephone Cable Core