Product Introduction
Alarm Security Display Stand Alone
Content
Product Introduction- --- 1 Multi-alarm function- --- 2 Installation
Installation of security display stand and mobile- --- 3 Indication light under different conditions- --- 4 Operation of RF remote- --- 5-6 Remove exhibit from stand- --- 7 Specifications- --- 8 Safety information and cautions- --- 9
Product Introduction
Main security sensor Exhibit fixing adhesive
buzzer
Extra security sensor Security spiral cable
Base sensor
For mobile cradle
LED indication light
spiral cable RJ11port Screw fixing screw
base adhesive
signal reception of remote control
4
Multi-alarm Function
2
Multi-alarm function to protect exhibits from theft in all aspects.
Alarm activated when the extra security sensor is removed. Alarm activated when the mouse sensor cable is cut off. Alarm activated when the spiral cable is cut off or broken Alarm activated when spiral cable is removed
Alarm activated when the security display stand is removed by force Alarm activated when exhibit is removed by force
Installation of Security Device and Mobile
Operation steps：
1-2.Take off the base sticker film and fix the display stand on counter.
3.Take off the mobile surface film and clean the mobile clearly.
4-5.Take off the adhesive film of mobile holder and stick the back of mobile on the holder
6.Take off the extra sensor film and stick it on the front of mobile(Notice: avoid covering the mobile camera.) 7.Use the remote control to send signal to the position (shown as the picture)after installation,and press”ON”to activate the display stand(remote distance 1-6cm)
Remark：
The environment temperature should be above 10℃ to ensure the viscosity of sdhesive
Adhesive contact surface should be very clean.
Press the surface for at least 30 senconds when paste the adhesive.
Indication Light
4
Under non-working condition,LED light blinks once at the moment the stand base is fixed on counter during first installation.
LED light blink in red during working condition.
LED light blinks rapidly when the stand alarms alarm
Blink in red Red light
Operation of remote control
LED indication light
Turn off device
Battery position
Operation:
Turn on device：Put or paste the stand on table and make sure of the full
contact between base sensor and table,then press”ON”
Stop alarm： Press”ON”to stop alarm when device alarms and the stand is
under working condition again
Turn off device：
Press “OFF”to turn off device when alarm is activated.
Remark：
•Point remote towards the small lock position to turn on/turn off the device •Remote distance :1-6cm
Turn on device/disalarm device
6
Battery replacing operations
Press the battery cover and rotate it in anti-clockwise direction until it can not be moved.
knock on the table and battery comes out replace the battery with + pole upwards put the cover back
Operation of remote control
Remove exhibit from stand
Detaching operation：
1.When alarm activated,press”OFF”on remote to turn off the stand..
2.Remove the stand from the exhibit counter(during
detaching,hard card is recommended to use to insert into the middle of the stand and counter and seperate them by swing.
３.Detach sensor on mobile and pay attention not to scratch the mobile.
４.Separate mobile with mobile holder.（counter(during detaching,hard card is recommended to use to insert into the middle of the stand and counter and seperate them by swing.）
Remark：Mobile can be taken from the stand during night or any other situation .When the spiral cable is removed,press “OFF”to stop the alarm and the mobile can be taken.
Specification
size
8
others：Safety information and cautions
Please read the following guide carefully to operate the device properly and securely
SAFETY WARNINGS
Do not dispose of batteries in a fire as they may explode. Dispose of batteries according to local regulations. Please recycle when possible. Do not dispose as household waste.
When using alcohol towel, please keep away from heat sources to avoid the cause of fire.
ELECTRONIC DEVICE
This device is without waterproof protection, when installation should pay attention to the waterproof and moisture-proof. Keep away from the heat sources, and assure the airiness as they may damage the device when overheating.
ENVIRONMENTAL PROTECTION
Please comply with the local regulations regarding packing materiais and dispose of discarded materials, please recycle when possible.
CARE AND MAINTENANCE
Take routine testing regularly to find troubleshooting in time to guard against the loss because of the malfunction of alarming.
Check the battery power regularly to avoid the malfunction of alarming because of low battery.
Do not attempt to open the device other than as instructed in this guide.
Do not drop and knock the device. Rough handling can break the internal circuit boards and fine mechanics.
Use a damp fine cloth to clean the device, do not use harsh chemicals, like alcohol and cleaning solvents to clean.
Do not store the device in hot and cold areas. High temperature can shorten the life of electronic device, damage batteries, and warp or melt certain plastics. When the device returns to its normal temperature, moisture can from inside the device and damage electronic circuit boards.
CAUTIONS
When alarming please release the device and stop alarming to save power.
Keep away from strong interference source, like powerful motor, electric welder, radio transmitter. It can shorten the life of battery.
