Brant Agitator

(1)

HMA Series

Installation, Operation,

and Maintenance Manual

sealed tank mud agitator

P.O. Box 2327

2800 N. Frazier

Conroe, TX 77305-2327 936-756-4800 phone 936-523-2788 fax

(2)

(3)

6 Maintenance and Repair

7

5 Parts and Drawings

Troubleshooting

8 Worldwide Locations

3

2 Installation

Product Information

General Information

1

4 Operation

(4)

Brandt is a registered trademark of Varco International, Inc.

All other product, brand, or trade names used in this publication are the trademarks or registered trademarks of their respective owners.

All rights reserved. This publication is the property of, and contains information proprietary to Varco International, nc. No part of this publication may be reproduced or copied in any form, or by any means, including electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Varco International, Inc.

(5)

Warranty

Brandt warrants that, for a period of one year from the date of delivery equipment of Brandt manufacture, the Equipment shall be free of defects in materials and

workmanship under normal use and service, and provided the Equipment is used and maintained in accordance with instructions supplied by Brandt. This is Brandt's sole and exclusive warranty. If a defect in the Equipment appears within one year from the date of shipment, and Purchaser has given written notice of such defect within thirty days from the discovery thereof, Brandt will repair or replace the part, at its option, by shipping a similar part FOB shipping point or, at its option, refund an equitable portion of the purchase price. Brandt may require the return, to a designated Brandt location, of the defective part, transportation prepaid to establish Purchaser's claim.

No allowance will be made for repairs undertaken without Brandt's written consent or approval.

This warranty applies only to equipment manufactured by Brandt. Warranties on equipment manufactured by others, if any, are assigned to Purchaser by Brandt (without recourse) at time of delivery. Any description of Equipment, drawings, specifications, and any samples, models, bulletins, or similar material, used in connection with this sale are for the sole purpose of identifying the Equipment and are not to be construed as an express warranty that the Equipment will conform to such description. Any field advisory or installation support is advisory only. The foregoing warranties are in lieu of all other warranties, whether oral, written, express, implied or statutory. Implied warranties or merchantability and fitness for a particular purpose will not apply. Brandt's warranty obligations and purchaser's remedies thereunder are solely and exclusively as stated herein. Purchaser's sole and exclusive remedy, whether based upon warranty, contract or tort, including negligence, will be to proceed under this warranty.

All liability of Brandt shall terminate one year from the date of delivery of the Equipment.

(6)

(7)

1 General Information

M10320 R2

Intended audience . . . 1-1

Conventions . . . 1-1

Notes, cautions, and warnings . . . 1-1

Notes . . . 1-1 Cautions . . . 1-1 Warnings . . . 1-1

Illustrations . . . 1-2

Safety requirements. . . 1-2

Personnel training . . . 1-2

Recommended tools . . . 1-2

General system safety practices. . . 1-3

Replacing components . . . 1-3

Maintenance . . . 1-3

Proper use of equipment. . . 1-3

(8)

1

M10320 R2

(9)

1 General Information

M10320 R2

Intended audience

This manual is intended for use by field engineering, installation, operation, and repair personnel. Every effort has been made to ensure the accuracy of the information contained herein. Brandt®, a Varco company, will not be held liable for errors in this material, or for consequences arising from misuse of this material.

Conventions

Notes, cautions, and warnings

Notes, cautions, and warnings appear throughout this manual to provide you with additional information, and to advise you to take specific action to protect personnel from potential injury or lethal conditions. They may also inform you of actions necessary to prevent equipment damage or conditions that may void your warranty. Please pay close attention to these advisories.

Notes

Cautions

Warnings

The note symbol indicates that additional information is provided about the current topic.

The caution symbol indicates potential risk of damage to equipment or injury to personnel. Follow instructions explicitly and take extreme care.

A caution symbol may also indicate a condition that voids your equipment warranty.

The warning symbol indicates a definite risk of equipment damage or danger to personnel. Failure to observe and follow proper procedures is likely to result in serious or fatal injury to personnel, significant property loss, or significant equipment damage.

(10)

1

M10320 R2

General Information

Illustrations

Figures provide a graphical representation of equipment components or screen snapshots for use in identifying parts or establishing nomenclature, and may or may not be drawn to scale.

For more specific component information pertinent to your rig configuration, see the technical drawings included with your Varco documentation.

Safety requirements

Brandt equipment is installed and operated in a controlled drilling rig environment involving hazardous operations and situations. Proper service and repair is important for safe and reliable operation. Operation and service procedures provided by Brandt manuals are the recommended methods of performing those operations.

Personnel training

All personnel performing installation, operations, repair, or maintenance procedures on the equipment, or those in the vicinity of the equipment, should be trained on rig safety, tool operation, and maintenance.

Contact the Brandt training department for more information about equipment operation and maintenance training.

Recommended tools

Service operations may require the use of tools designed specifically for the purpose described. When stated, use only these tools.

To avoid injury to personnel or equipment damage, carefully observe the following safety requirements.

During installation, maintenance, or repair of equipment, personnel should wear protective gear.

(11)

1 General Information

M10320 R2

General system safety practices

Local codes may apply. Please consult them prior to performing any operation. The presence of a Brandt representative at the site does not relieve the owner/ operator of responsibility to follow published installation, operation, and maintenance instructions.

The equipment discussed in this manual may require or contain one or more utilities, such as electrical, hydraulic, pneumatic, or cooling water.

Isolate all energy sources before beginning work.

Avoid performing maintenance or repairs while the equipment is in operation.

Wear proper protective equipment during equipment installation, maintenance, or repair.

Replacing components

Verify that all components (such as cables, hoses, etc.) are tagged and labeled during disassembly and reassembly of equipment.

Replace failed or damaged components with Brandt certified parts. Failure to do so could result in equipment damage or personal injury.

Maintenance

Equipment must be maintained on a regular and routine basis. See the service manual for maintenance recommendations.

Proper use of equipment

Brandt equipment is designed for specific functions and applications, and should be used only for its intended purpose.

Before installing or performing maintenance or repairs on equipment, read the following instructions to avoid endangering exposed persons or damaging equipment.

Failure to conduct routine maintenance could result in equipment damage or injury to personnel.

(12)

1

M10320 R2

(13)

2 Product Information

M10320 R2

Introduction . . . 2-1

Unit description . . . 2-1

General description. . . 2-1

Motor. . . 2-1

Gearbox . . . 2-2

Mounting base . . . 2-2

Impeller . . . 2-2

Contour-blade impellers . . . 2-3 Impeller placement . . . 2-3 Impeller shaft . . . 2-3

Bottom shaft stabilizer. . . 2-4

Options . . . 2-4

(14)

2

M10320 R2

(15)

2 Product Information

M10320 R2

Introduction

HMA series agitators are heavy-duty mechanical mixers for viscous fluids specially designed for seal type tanks. Several models are available to meet a variety of mixing needs.

The naming convention for these models is:

HMA-X

where X = the horsepower of the unit. For example, HMA-20 is the 20 hp mud agitator for seal type tanks.

Each HMA series agitator uses a pipe-spool shaft and impeller(s) to maintain a homogeneous mixture of liquids and solids within a tank. Impellers have contour blades (axial flow), and may be installed in multiple configurations to provide the desired results. The impeller shaft is suspended from and attached to the output shaft of the low-profile, skid-mounted gearbox. The gearbox uses a worm-worm gear drive system to reduce the rotational speed of the explosion-proof motor to drive the impeller(s).

HMA series agitators are available in models ranging from 25 to 40 horsepower, and can be seal base unit or shaft seal units. Impellers range from 54 inches (1372 mm) diameter to 84 inches (2134 mm) diameter.

Unit description

General description

Each HMA consists of a shaft-mounted impeller, motor, gearbox, and mounting base. Electrical controls, special coatings, custom bases, and other options are available.

Motor

The motors used on Brandt mud agitators are explosion proof, T-frame, three-phase electric motors directly coupled to the gearbox using a flexible coupling with a solid steel guard. Motors are available for most voltage/frequency requirements. Other electrical code styles and temperature ratings are also available.

Nominal ratings

Volts Hz RPM

(16)

2

M10320 R2

Product Information

Gearbox

The gearbox is a triple reduction worm-worm gear drive, reducing the motor speed (900 rpm @ 60 Hz) to the agitator speed (30 rpm) in a single 30:1 reduction. The gearbox contains an output shaft, two seals, and four to six bearings in addition to the worm-worm gear. The bearings are spaced to minimize shaft vibration and deflection, and seals are readily obtainable standard sizes. Unlike many competing agitators, Brandt’s gearbox requires no manual lubrication of the bottom output bearing.

Mounting base

The motor and gearbox are assembled on a common base with heavy grade

fasteners. The base is sand blasted to white metal, primed with zinc, and finish coated with urethane. Special coatings are available as an option.

Impeller

Impellers are contour blade style, and may be installed in multiple configurations to provide the desired results.

Impellers range from 54 inches (1372 mm) to 84 inches (2134 mm) in diameter. Larger custom-designed blades and mixing systems are also available. See Chapter 8 to find the Brandt office nearest you.

Impeller speed is 30 rpm for 60 Hz applications.

Impeller measurements

Diameter Weight IN MM LB KG 54 1372 195 88 56 1422 204 93 60 1524 214 97 64 1626 224 102 84 2134 387 176

(17)

2 Product Information

M10320 R2

Contour-blade impellers

On contour blade impellers (Figure 2-1), the blades are designed with a variable pitch reducing the horsepower requirements and inducing less shear to the mud. Contour blades move liquid downward to the bottom of the tank, along the tank bottom toward the tank walls, and then up the tank wall. All fluid in the tank is mixed continuously, and the same consistency is maintained in all parts of the tank.

Field experience has confirmed that this design provides the most homogeneous mixture in the widest range of installations. Fluid agitation minimizes fluid control problems caused by inconsistent mixtures.

Figure 2-1. Contour blade impellers promote axial flow with less shear to the mud.

Impeller placement

Contour blade impellers should be placed on the shaft so that the distance between the bottom of the tank and the lower edge of the blades is equal to .75 times the diameter of the impeller.

Impeller shaft

HMA standard impeller shafts are manufactured of eight-inch pipe spools. The impeller shaft is coupled to the gearbox with a rigid coupling.

Shaft length is determined by tank depth. When ordering impeller shafts, always specify the actual tank depth. Tank depth is defined as the distance from the bottom of the tank to where the agitator is mounted.

(18)

2

M10320 R2

Product Information

Bottom shaft stabilizer

A bottom shaft stabilizer is required to reduce side loading on the gearbox bearings. The stabilizer also protects the agitator shaft and impeller when auxiliary equipment is carried inside the mud tank during rig moves.

Options

There are several options available for HMA-series units. Popular options include special paint finishes, remote starters, other electrical controls, and special duty motors. Contact your Brandt sales representative to discuss which options may be right for your application. See Chapter 8 to find the Brandt office nearest you.

(19)

2 Product Information

M10320 R2

Available models

HMA series units are available in several models, from 25 hp to 40 hp. The following table lists the physical specifications for each unit.

HMA series models

Model HP Length Width Height

Weight less shaft & impeller HMA-25 Seal Base 25 68 5/8 in (1743 mm) 43 in (1092 mm) 39 7/8 in (1013 mm) 3606 lb (1636 kg) HMA-25 Shaft Seal 25 68 5/8 in (1743 mm) 43 in (1092 mm) 60 7/8 in (1546 mm) 4743 lb (2151 kg) HMA-30 Seal Base 30 72 ¼ in (1835 mm) 43 in (1092 mm) 39 7/8 in (1013 mm) 3650 lb (1656 kg) HMA-30 Shaft Seal 30 72 ¼ in (1835 mm) 43 in (1092 mm) 60 7/8 in (1546 mm) 4787 lb (2171 kg) HMA-40 Seal Base 40 72 ¼ in (1835 mm) 43 in (1092 mm) 39 7/8 in (1013 mm) 3815 lb (1730 kg) HMA-40 Shaft seal 40 72 ¼ in (1835 mm) 43 in (1092 mm) 60 7/8 in (1546 mm) 4950 lb (2245 kg)

Accurate tank dimensions and mud weight are required to properly size agitator shaft and impeller.

(20)

2

M10320 R2

(21)

3 Installation

M10320 R2

Installation

Proper mounting location

Be sure the mounting location is level, free from obstructions, and will provide a stable platform for the unit during normal operation.

Mounting fasteners

Attach the unit to its mounting surface with heavy-duty threaded fasteners, one at each corner of the base. As an option, the base may be welded directly to the mounting surface.

Proper electrical service

Check all electrical components for proper voltage, frequency, duty rating, and adherence to applicable electrical codes.

Oil fill breather

The HMA ships with the oil fill breather cap installed on the gearbox.

Impeller rotation

The impeller should rotate clockwise when viewed from above.

If the impeller rotates in the wrong direction, switch any two lead wires at the starter controls or at the motor. To switch wires at the motor, refer to the wiring diagram on the HMA name plate or inside the junction box cover.

Disconnect power to the electrical circuit before beginning any work on the electrical controls or motor rotation.

(22)

3

M10320 R2

Installation

Impeller shaft alignment

Check the impeller shaft coupling regularly for proper alignment. As shown in Figure 3-2, the impeller shaft should not touch any portion of the stabilizer (if installed) when the HMA is not running.

Figure 3-2. Impeller shaft alignment

Long term storage

Store the HMA in a cool, dry place.

The equipment is packaged to prevent corrosion for a period of twelve (12) months if stored indoors. During shipping, all openings are covered or capped to protect the inside from dust, rust and moisture. Threaded connections, couplings and shafts are coated with corrosion inhibitor.

If the equipment is to be subjected to prolonged shutdown or storage, the following steps should be taken to ensure that the unit does not degrade during storage.

Motors are shipped from the factory pre-lubricated. Rotate the shafts thirty (30) revolutions once per month to keep the bearings in the motor and speed reducer lubricated.

Place protective caps over all threads to further guard against contamination.

Keep temperature as consistent as possible to prevent condensation.

If the motor is equipped with space heaters, connect them to the appropriate voltage and hertz power.

If unit is stored for more than one (1) year, add grease before start-up. Some contact between shaft and stabilizer is normal during operation, but immediately correct any hard striking.

(23)

3 Installation

M10320 R2

Installation . . . 3-1

Proper mounting location . . . 3-1

Mounting fasteners . . . 3-1

Proper electrical service . . . 3-1

Oil fill breather. . . 3-1

Impeller rotation . . . 3-1

Impeller shaft alignment . . . 3-2

(24)

3

M10320 R2

(25)

4 Operation

M10320 R2

Operation . . . 4-1

Startup . . . 4-1

(26)

4

M10320 R2

(27)

4 Operation

M10320 R2

Operation

Startup

Before starting the HMA, check that:

All steps in "Installation" on page 3-1 are complete.

Oil level is correct as shown in Figure 4-1.

The oil breather plug is clear of any obstruction.

Impeller shaft is properly aligned.

No oil leaks are present.

No wear or cracks appear on the rubber inserts on input shaft coupling.

Figure 4-1. Oil level check

Oil should be level with the bottom of the oil level hole as shown in Figure 4-1 Do not overfill.

Initial oil change

Change the oil after the first five days of operation.

Always check the oil level with the HMA off.

(28)

4

M10320 R2

(29)

5 Troubleshooting

M10320 R2

(30)

5

M10320 R2

(31)

5 Troubleshooting

M10320 R2

Troubleshooting

Sympton Possible cause Solution

Agitator won't run No power Check power Tripped breaker Check voltage

Check that agitator shaft is not dragging on bottom stabilizer

Agitator runs hot Wrong grade oil for the ambient temperature

Refer to manual for correct oil

No oil in gearbox Check for leaks, add oil Too much oil in gearbox Open oil level plug No grease in upper bearing Grease bearings Agitator makes high-speed

grinding noise

Worn input bearing Replace worn bearings

Agitator makes low-speed grinding noise

Worn drop or thrust bearing Replace drop or thrust bearing

Agitator makes grinding noise

Worn gears Rebuild gearbox, check gears for galling Agitator vibrating Misaligned motor coupling Align motor coupling Loss of oil Bad output shaft seal Replace seals

Bad input shaft seal Replace seals Erratic shaft motion Bent shaft Check straightness

Failed drop bearing Replace bearing

Hot oil. Allow gearbox to cool or open vent plug before opening level plug. Hot oil may escape rapidly and cause burns.

(32)

5

M10320 R2

(33)

6 Maintenance and Repair

M10320 R2

Maintenance . . . 6-1

(34)

6

M10320 R2

(35)

6 Maintenance and Repair

M10320 R2

Maintenance

Inspection

The performance of a parallel helical gear drive reducer depends on the quality of lubricating oil.

Component Check

Gearbox temperature The performance of a worm gear drive reducer depends on the quality of lubricating oil. A worm gear runs hot during the first days of operation. During normal operation, there is no cause for alarm unless the temperature exceeds 200°F (93°C) or 100°F above ambient temperature.

Oil level Check oil level at the oil level plug located on the side of the gear reducer.

See Figure 6-1 on page 6-4 to locate the plug.

Check oil level with the unit off. Oil should be level with the bottom of the oil level plug-hole.

See Figure 6-1 on page 6-4 to locate the plug.

Oil fill breather Visually check that oil fill breather is free from any mud or other material.

See Figure 6-1 on page 6-4 to locate the plug. Oil seals Visually check for signs of leaks or visible damage. Motor Visually check condition of fan guard.

Be sure that motor cooling fins are clear and free of mud or other material.

Impeller shaft coupling Visually check to ensure coupling is tight and all fasteners are in place.

Impeller Check condition of impeller for bent, damaged, or worn blades.

Periodically check keyed coupling to ensure it is tight and all fasteners are in place.

Bottom shaft stabilizer (if installed)

Visually inspect condition of stabilizer for wear or other damage.

Motor/reducer coupling Visually inspect coupling, coupling insert, and coupling guard for damage.

(36)

6

M10320 R2

Maintenance and Repair

Bearing Lubrication

Grease the gearbox top bearing every 100 operating hours with recommended bearing grease. About a 3/8 in (9mm) ball of grease is sufficient.

Grease the motor every three months.

The greases shown in this manual are given as examples of appropriate greases. Any other grease that meets the standards of the National Lubricating Grease Institute (NLGI) is acceptable.

Oil changes

The initial oil fill should be changed after 100 operating hours (approximately two weeks) and then at 1800-hour intervals. In practice, change every 6-12 months depending on operating conditions. The companies and oil shown below are typical. Any other oil that meets the standards of the American Gear Manufacturers

Association (AGMA) 7C and 8C is acceptable.

If you use synthetic oils, you may double the operating hours between changes.

Do not over grease.

Recommended greases

Brand Above 32°F (0°C) Below 32°F (0°C)

BP Lubrication Engineers

Energrease LS2LE1275 Energrease LS2LE1275

Chevron Crown EP Special 2

Conoco Polar Start DN600 SRI

Shell Alvania AP-2

Royal Purple Ultra-Performance Synthetic Ultra-Performance Synthetic

Texaco Marfax 3 Marfax 2EP

Exxon Unirex N-2

EP oil is not recommended.

(37)

6 Maintenance and Repair

M10320 R2

When changing the oil, always use the oil grade previously in use. Mixing oils of different grades is not permissible. In particular, synthetic oil may not be mixed with mineral oils or different synthetic oils. If you are planning to change oil types, the gearbox must be flushed through thoroughly with the new oil grade.

If synthetic oils are used the operating hours between changes may be doubled.

Recommended oils

Brand AGMA No. 7C 15° to 60°F -9° to 16°C AGMA No. 8C 50° to 125°F 10° to 52°C BP/Amoco GR-XP 460 GR-XP 680 ARCO Modoc 175

Chevron Cylinder Oil 460X Cylinder Oil 680X

Conoco Inca Oil

Exxon Cylesstic TK460 Cylesstic TK680

Mobil 600W Super Cylinder Oil 600W Super Cylinder Oil Mobil MobilGear SHC 460 MobilGear SHC 680 Pennzoil Cylinder Oil #8 Cylinder Oil #6

Phillips Hector 460S Hector 630S

Royal Purple Synergy ISO 460 Synergy ISO 680 Shell Valvata Oil J460 Valvata Oil J680

Texaco Vanguard 460 Honor 680

(38)

6

M10320 R2

Maintenance and Repair

To change the gearbox oil

Verify location of the oil drain plug, oil fill breather cap, and the oil level indicator for your HMA-series model in Figure 6-1.

1. Switch the unit off. 2. Remove the oil drain plug.

3. Drain the used oil into a suitable container and replace the oil drain plug. 4. Remove the oil breather.

5. Fill the gearbox with the correct amount of acceptable oil. The gear reducer is properly filled when oil just begins to flow out of the oil level hole.

6. Replace the oil breather.

Figure 6-1. Location of plugs

Gear reducer oil capacity

Gear reducer capacity is 16 gallons (61 liters).

Gear oil is extremely slippery and sticky. Gear reducers are most easily filled using a pump or pressurized lubrication gun. Be sure to dispose of used oil properly and clean area of any spilled oil after completing this procedure.

fitting

(39)

6 Maintenance and Repair

M10320 R2

Fastener torque (lb/in)

Fastener location HMA-25 HMA-30 HMA-40

Gearbox shaft coupling 5500 5500 5500

Shaft & impeller coupling 5500 5500 5500 Gearbox shaft coupling bushing 2450 2450 2450

(40)

6

M10320 R2

Maintenance and Repair

Routine maintenance checklist

Your HMA-series unit is designed for years of dependable service with routine inspection and maintenance. Additional copies of this checklist should be placed close to the unit for quick reference.

Startup

1. Check oil level with agitator off: oil should be level with the bottom of the oil level hole.

2. Impeller rotation: The impeller should rotate clockwise when viewed from top. 3. Oil fill/breather plug: plug must be clear of any obstruction to prevent pressure

build-up and possible seal damage. 4. Agitator should operate with no vibration.

5. Check rubber insert on input shaft coupling for wear and cracks.

6. For optimal performance, change the oil after the first five days of operation.

Daily

1. Inspect for oil leaks.

2. Keep motors clean and ventilation opening clear of mud build-up or other debris.

3. Check impeller shaft coupling for proper make-up.

(41)

6 Maintenance and Repair

M10320 R2

Periodic

1. Check oil level.

2. Grease the gearbox top bearing with the approved bearing grease (see the "Recommended greases" table on page 6-2) every 100 operating hours. About a 3/8 in (9mm) ball of grease is sufficient.

3. Change oil (see the "Recommended oils" table on page 6-3) every 100 operating hours.

4. Lubricate motors every three months.

Do not over lubricate.

(42)

6

M10320 R2

(43)

7 Parts and Drawings

M10320 R2

One-year recommended spare parts . . . 7-1

HMA-25 seal base mud agitator installation

A8500. . . 7-2

HMA-30 seal base mud agitator installation

A13101. . . 7-4

HMA-40 seal base mud agitator installation

A13294. . . 7-6

HMA-25 shaft seal mud agitator installation

A11810. . . 7-8

HMA-30 shaft seal mud agitator installation

A13041. . . 7-10

HMA-40 shaft seal mud agitator installation

A13230 . . . 7-14

Typical HMA shaft and impeller assembly

(44)

7

M10320 R2

(45)

7 Parts and Drawings

M10320 R2

One-year recommended spare parts

Recommended spares are for typical operating conditions. Choose an oil applicable to your temperature requirements.

HMA replacement parts

Part # Description Qty

9AB Bearing input (open end) 1 9Z Bearing output (open end) 1

10R Oil seal input 1

10S Oil seal output 2

Oil 1 46J 15°F to 60°F - 5 gal 46A 15°F to 60°F - 55 gal 46L 50°F to 120°F - 5 gal 46B 50°F to 120°F - 55 gal 46AA -40°F to 40°F - 5 gal 46Z -40°F to 40°F - 55 gal

(46)

7

M10320 R2

Parts and Drawings

HMA-25 seal base mud agitator installation

A8500

(47)

7 Parts and Drawings

M10320 R2

A8500 parts list

Item # Part # Description Qty

1 19FL Gear reducer w/oil 1

2 1UV Motor 1 3 8544 Base 1 4 8638 Coupling guard 1 5 21BT Coupling motor 1 6 21BZ Coupling reducer 1 7 20J Flexible insert 1

8 21Q Rigid coupling female 1

9 3V Bushing gear reducer output shaft 1

10 22AV HHCS 1.13 7UNC x 4.50 4

11 35AU 1-1/8 in lock nut 4

12 36AQ 1-1/8 in washer 8

13 77F Pallet required for shipping (not shown) 1

14 22UE HHCS 5/8 11UNC x 2-3/4 4

15 35V 5/8 in lock nut 4

16 36AP 5/8 in washer 8

17 Paint

18 63K Nameplate (not shown) 1

19 22Y HHCS 0.38 16UNC x 1.00 2

20

21 36AT 3/8 in washer 4

22 8561 Rigid coupling retainer plate 1

23 22PI HHCS 5/8 11UNC x 1-3/4 2

24 36BP 5/8 in lock washer 2

25 78BP Conduit outlet box type GUAT 69 1

26 47B Nipple 2 in close NPT 1

27 40AD Reducer 2 x 1/2 RE61 1

(48)

7

M10320 R2

Parts and Drawings

HMA-30 seal base mud agitator installation

A13101

(49)

7 Parts and Drawings

M10320 R2

A13101 parts list

1 19HF Gear reducer w/oil 1

2 1VW Motor 1

3 13102 Base 1

4 13198 Coupling guard 1

5 21LY Coupling motor 1

6 21LX Coupling reducer 1

7 20AS Flexible insert 1

10 22AV HHCS 1.13 7UNC x 4.50 4

14 22UE HHCS 5/8 11UNC x 2-3/4 4

17 Paint

19 22Y HHCS 0.38 16UNC x 1.00 2

22 22PI HHCS 5/8 11UNC x 1-3/4 2

24 40R 3 in x 2 in reducer 1

26 47B 2 in close nipple NPT 1

27 22BA HHCS 7/8 9UNC x 2-1/2 6

(50)

7

M10320 R2

Parts and Drawings

HMA-40 seal base mud agitator installation

A13294

(51)

7 Parts and Drawings

M10320 R2

A13294 parts list

1 19FL Gear reducer w/oil 1

2 1VZ Motor 1

3 13102 Base 1

10 22AV HHCS 1.13 7UNC x 4.50 4

14 22UE HHCS 5/8 11UNC x 2-3/4 4

17 Paint

19 22Y HHCS 0.38 16UNC x 1.00 2

22 22PI HHCS 5/8 11UNC x 1-3/4 2

24 40R 3 in x 2 in reducer 1

26 47B 2 in close nipple NPT 1

27 22BA HHCS 7/8 9UNC x 2-1/2 6

(52)

7

M10320 R2

Parts and Drawings

HMA-25 shaft seal mud agitator installation

A11810

(53)

7 Parts and Drawings

M10320 R2

A11810 parts list

2 1UV Motor 1 3 11819 Base 1 4 8638 Coupling guard 1 5 21BT Coupling motor 1 6 21BZ Coupling reducer 1 7 20J Flexible insert 1

8 21P Rigid coupling male 1

10 22AV HHCS 1.13 7UNC x 4.50 4

12 36AQ 1-1/8 in washer 8 13 36BJ 3/4 in washer 1 14 22UE HHCS 5/8 11UNC x 2-3/4 4 15 35V 5/8 in lock nut 4 16 36AP 5/8 in washer 8 17 Paint

19 22Y HHCS 0.38 16UNC x 1.00 2

20 9411 Shipping bracket 1

22 9088 Shaft housing subassembly 1

24 9097 Stub shaft 1

25 57K 5/8 in braided packing 6

26 9142 Lantern ring 1

27 3U Bushing shaft 2

(54)

7

M10320 R2

Parts and Drawings

HMA-30 shaft seal mud agitator installation

A13041

(55)

7 Parts and Drawings

M10320 R2

A13041 parts list

2 1VW Motor 1

3 13305 Base 1

10 22AV HHCS 1.13 7UNC x 4.50 4

19 22Y HHCS 0.38 16UNC x 1.00 2

20 35L 3/8 - 16 lock nut 2

(56)

7

M10320 R2

Parts and Drawings

33 22BA HHCS 7/8 9UNC x 2-1/2 6

34 48FQ 1-1/2 oil drain hose 3

35 14BT 1-1/2 hose clamp (worm) 4

36 47AD 1/2 nipple close 1

37 44HV 1-1/2 elbow 45° 1

38 9411 Shipping bracket (not shown) 1

A13041 parts list (Continued)

(57)

7 Parts and Drawings

(58)

7

M10320 R2

Parts and Drawings

HMA-40 shaft seal mud agitator installation

A13230

(59)

7 Parts and Drawings

M10320 R2

A13230 parts list

2 1VZ Motor 1

3 13531 Base 1

10 22AV HHCS 1.13 7UNC x 4.50 4

19 22Y HHCS 0.38 16UNC x 1.00 2

20 35L 3/8 - 16 lock nut 2

(60)

7

M10320 R2

Parts and Drawings

33 22BA HHCS 7/8 9UNC x 2-1/2 6

34 48FQ 1-1/2 oil drain hose 3

35 14BT 1-1/2 hose clamp (worm) 4

36 47AD 1/2 nipple close 1

37 44HV 1-1/2 elbow 45° 1

38 9411 Shipping bracket (not shown) 1

A13230 parts list (Continued)

(61)

7 Parts and Drawings

(62)

7

M10320 R2

Parts and Drawings

Typical HMA shaft and impeller assembly

PI13534

(63)

7 Parts and Drawings

M10320 R2

PI13534 parts list

1 Spool 8 in x 6 ft- 1/4 in shaft 1

2 Spool 8 in x 6 ft - 2-9/16 in shaft 2 3 Spool 8 in x 5 ft - 11-7/8 in shaft 1

4 Stub shaft 1

5 84 in blade 4

6 84 in blade with stabilizer 4

7 54 in blade 4

8 Impeller hub 3

9 Slap ring 1

10 Slap ring clip 4

11 Nut hex 3/4 in nylock GR 5 zinc 52

12 3/4 in flat zinc washer 52

13 HHCS 3/4 10UNC x 3 GR 5 zinc 48

14 7/8 in lock washer GR 5 zinc 60

15 HHCS 7/8 9UNC x 5-1/2 GR 5 zinc 60

16 Nut hex lock 7/8 9UNC GR 5 zinc 60

17 7/8 in washer flat 120

18 HMA-25 slap ring bottom stabilizer 1

19 Spool 8 in x 4 ft 1

(64)

7

M10320 R2

(65)

8 Worldwide Locations

M10320 R2

International . . . 8-1

(66)

8

M10320 R2

(67)

8 Worldwide Locations

M10320 R2

International

Argentina Bolivia San Martin 345 4to Piso Buenos Aires 1004 Argentina

KM 6.5 Carretera Antigua Acochabamba (Al lado Casa Cotas)

Santa Cruz del la Sierra 3813 Bolivia phone 54 114 394-3939 54 114 394-4599 54 114 394-6213 phone 591 33 553500 591 33 553501 591 33 554280 fax 54 114 394-4499 fax 591 33 553501 Brazil Canada

Padre Guilherme Lago Castro 559 Barrio Cancela Preta

Macae, Rio de Janeiro Brazil

6616 - 45th Street Leduc, Alberta T9E 7C9 Canada phone 55 222 773-5437 55 222 773-3115 55 222 773-4197 55 222 773-3986 phone 780-986-6063 fax 55 222 763-9346 55 222 763-9343 fax 780-986-6362 Canada Equador #1600 540-5thAvenue S.W. Calgary, Alberta T2P 0M2 Canada Luxemburgo 143 y Holanda Edificio Luxemburgo Depto. 7A Quito Ecuador phone 403-264-9646 phone 593 2-224-3212 593-2-224-3224 fax 403-263-8488 fax 593 2-224-3212 593 2-224-3224 593 2-246-5359

The Netherlands Norway

De Hulteweg 3b 7741 LE Coevorden The Netherlands Gamie Forusvn 25 Staveanger N-4033 Norway phone 31 524-582718 phone 47 51-951460 fax 31 52-534814 fax 47 51-951470

Scotland United Arab Emirates

(68)

8

M10320 R2

Worldwide Locations

United States

California Colorado 7300 Downing Avenue Bakersfield, CA 93308 410 17th Street, Suite 1170 Denver, CO 80202 phone 661-588-8503 phone 303-592-9250 fax 661-588-8506 fax 720-904-0693 Louisiana Louisiana

Advanced Wire Cloth 618 Hangar Drive P.O. Box 9188 (70562) New Iberia, LA 70560 1515 Poydras Street Suite 1850 New Orleans, LA 70112 phone 337-365-7700 phone 504-636-3660 fax 337-365-0375 fax 504-636-3670

Louisiana North Dakota

1327 Eraste Landry P.O. Box 52252 (70505) 4965 2nd Street SW P.O. Box 326 (58602) Dickinson, ND 58601 phone 800-359-5935 phone 701-227-8608 fax 337-235-3739 fax 701-227-8612 Oklahoma Texas

3216 Aluma Valley Drive P.O. Box 95169 (73143-5169) Oklahoma City, OK 73121 426 Flato Road Corpus Christi, TX 78405 phone 405-478-0047 800-725-4986 phone 361-289-7794 800-725-4974 fax 405-478-0177 fax 361-289-9058 Texas Texas 4506B Britmore Houston, TX 77041

12950 West Little York Houston, Texas 77041 phone 713-896-1172 phone 713-256-4100 fax 713-466-1496 fax 713-856-4133 Texas Wyoming 4710 Andrews Hwy Odessa, TX 79762 6775 W. Yellowstone P.O. Box 2852 (82601) Casper, WY 82604 phone 915-560-6802 888-563-0663 phone 307-237-9431 307-237-9441 fax 915-550-3190 fax 307-237-6110