• No results found

VEK SCREW COMPRESSOR

N/A
N/A
Protected

Academic year: 2021

Share "VEK SCREW COMPRESSOR"

Copied!
53
0
0

Loading.... (view fulltext now)

Full text

(1)

VEK 20-50

SCREW COMPRESSOR

MAINTENANCE AND

SPARE PARTS

GUIDE

Address and communication informations:

Ali Bey Köyü,Karasinan Asfaltı Telefon No: +90 212 728 43 43 (Pbx) Mevkii,Silivri,İstanbul, Turkey Fax : +90 212 728 70 23

www.komsan.com.tr e-mail:info@komsan.com.tr

09 FRM 020 Rev 10

(2)

VEK 20-50 VİDALI KOMPRESÖR KATALOG FİHRİSTİ

SAYFA NO

IMPORTANT SECURITY RULES IN OPARATING, MAINTANANCE AND REPAIR OF THE COMPRESSORS--- 4

CARRYING THE COMPRESSOR --- 5

IMPORTANT THINGS TO BE CHECKED AT THE FIRST START UP--- 6

PLACING OF THE COMPRESSOR--- 7

SAMPLE INSTALLATION--- 8

INLET AND OUTLET AIR FLOW OF THE COMPRESSOR ROOM--- 9

SAMPLE ELECTRIC INSTALLATION SCHEME--- 10

PLC--- 11

COMPRESSOR DIMENSION--- 12

PLACING OF THE AIR DRYER--- 13

PLACING OF THE AIR RECEIVER--- 14

PERIODICAL MAINTENANCE PROGRAM--- 15

PERIODIC MAINTENANCE INTERVALS--- 16

PROBABLE BREAKDOWNS AND REMOVING METHODS--- 17

THE MAINTENANCE THAT MUST BE DONE BY THE USER--- 18

FİRST OPERATING INSTRUCTIONS--- 19

SPARE PART LIST--- 20

MAIN ASSEMBLY DRAW--- 21

MAIN ASSEMBLY LIST--- 22

HYDROLIC GROUP DRAW--- 23

HYDROLIC GROUP LIST--- 24

MOTOR GROUP DRAW--- 25

MOTOR GROUP LIST--- 26

AIREND GROUP DRAW--- 30

AIREND GROUP LIST--- 31

OIL RECEIVER DRAW--- 32

OIL RECEIVER LIST--- 33

AIR INLET VALVE DRAW--- 34

AIR INLET VALVE LIST--- 35

MINUMUM PRESSURE VALVE DRAW--- 36

MINUMUM PRESSURE VALVE LIST--- 37

THERMOSTATIC VALVE DRAW--- 40

THERMOSTATIC VALVE LIST--- 41

BONNET GROUP DRAW--- 42

BONNET GROUP LIST--- 43

PNEUMATIC GROUP DRAW--- 44

PNEUMATIC GROUP LIST--- 45

THE SCREW COMPRESSOR’S HYDRO-PNEUMATİC CYCLE AND WORKİNG PRİNCİPLE--- 46

ELECTRICAL GROUP DRAW--- 47

ELECTRICAL GROUP LIST--- 48

INSTRUMENT PANEL GROUP DRAW--- 49

INSTRUMENT PANEL GROUP LIST--- 50

SERVICE INFORMATIONS--- 51

(3)

VEK

20-50

SCREW COMPRESSOR

OPERATION

MAINTENANCE AND

SPARE PARTS

GUIDE

MOTOR POWER

WORKING PRESSURE

VEK

20 – 50

Hp

7.5 – 10 - 13

Bar

Adress And Communication Informations

:

Ali Bey Köyü Karasinan Asfaltı

Phone No :+90 212 728 43 43 (Pbx)

(4)

FIRST SAFETY

IMPORTANT SECURITY RULES IN OPERATING, MAINTENANCE AND

REPAIR OF THE COMPRESSORS

1-) Use KOMSAN air receivers, equipments and KOMSAN original spare parts produced in compliance with the norms of TSE 1613

2-) In case compressor is worked parallel with another compressor or is connected an air system with the same pressure, do not use check valve in the compressor air outlet.

3-) The materials of the pressurized air, pipe and hoses must be in compliance with the pressure.

4-) Do not use scratched, spoilt , decayed and broken hoses. Store the hoses away from the heat source and direct sun rays.Burst of a hose may harm a human.

5-) Fix the suitable connectors to the lip of the hose.

6-) If pressurized air is used to clean the tools and parts, it must be done carefully. Be careful with the dust while it is cleaned from the machine. Use googles during cleaning.

7-) While air is used from the hose and installation directly, there must not be any foreign substance in hose. Hold the hose tip tightly and securely. Otherwise, hose tip may be dangerous because it can hit in the directions of the right and left like a whip. Open the air outlet valve carefully, check if air gets out of the hose freely. Clogged hose could become an air rifle.

8-) Do not hold pressed air onto your skin. Do not hold tip of the hose onto another person. Do not clean dusts on you with pressurized air.

9-) A pressure air system or tool must be operated in accordance with its designed pressure. 10-) Drain compressor pressure completely before dismantling hose and air line.

11-) Tips of the electrical cables must not be open

12-) Electrical connection must be done by authorized electrician. 13-) Pressure tests of the air receivers must be done each year.

(5)

CARRYING THE COMPRESSOR :

Compressor must be carried in vertical position. All motions and collisions which may cause

damage must be avoided. Compressors must not be pushed or pulled through its canopy or doors. Compressors must not be hung in any other way than it is shown in figure 2.

CARRYING BY MEANS OF FORKLIFT OR HYDRAULIC CARRIER:

When carrying the compressor with a forklift or hydraulic carrier the carrying the support forks of the forklift must be inserted below the compressor as seen in picture 1.

CARRYING HANGED BY MEANS OF A HOIST:

When carrying the compressor by means of a hoist, insert iron rods to the gaps of the compressor bottom pallet as seen in picture 2. Care must be given that the upper rod must not touch the compressor, nor the ropes rubbing on the side of the compressor.

INSTALLATION:

1-) Install the compressor in a room as it is indicated in picture-4.

2-) Keep the compressor away from the sunlight or other devices which may increase ambient temperature such as generator sets heating systems etc.

3-) Enough ventilation is absolutely necessary for a compressor. A sample ventilation diagram is presented in picture-7. Inlet air of the compressor room must be clean and without any contamination of porous gases or chemicals. If necessary , an appropriate filtration must be installed at the air entrances of compressor room. 4-) Compressor must be installed on the smooth ground, its feet must be put correctly to the ground. Compressor must not be installed to the ground. Compressor must be seated on the concrete base. (Max. declination of the floor, where the compressor is to be assembled, must not be more than ±2 degrees)

5-) If compressor is to be used with dryers, filters or receiver, please check picture-6 for how to connect these instruments to your compressor.

CONNECTING TO MAINS:

1-) Compressor must be separately grounded according to your country’s requirements. (See picture-6) Neutral connection is not ground . Compressor may burn because of the static charge if not grounded.

2-) Do not allow main supply cables to lay on the floor freely. D o secure them so that they may not cause any dangerous accidents.

3-) Check all connections are done tight and secure on the mains supply.

4-) Suitable circuit breaker and delayed fuse must be placed on the mains supply (see table-2). 5-) There must be no temporary connection on the mains supply cables.

6-) Compressor operating voltage must be 380±19 volt, unless it is designed for other voltages, during the full load operation.

7-) TTR type cable must be used with appropriate dimensioning (see table-2).

8-) Keep the compressor away from the moisture if it is not going to be used for a long time.

TAKE OUT THE WOODEN FOUNDATION AFTER CARRYING THE COMPRESSOR

PICTURE-2 PICTURE-1

(6)

IMPORTANT THINGS TO BE CHECKED AT THE FIRST START UP

1-) Check the earth, neutral and phases (R-S-T) if they are fit into system appropriately when compressor starts. 2-) Check the ambient temperature.

3-) Check the oil level.

IMPORTANT THINGS DURING OPERATION

1-) Covers must be kept close.

2-) Water and oil must not be poured onto compressor and foreign objects must not be put onto compressor. 3-) Do not touch the inside of the compressor or do not try to make any reparations by yourself.

STOPPING

To stop the compressor completely, push the ‘’STOP’’ button. Compressor will stop in a certain time. Push the ‘’EMERGENCY STOP’’ button when emergency situation may occur.

CONTROL PANEL

VEK20/50

easy

EMERGENCY STOP ACIL DURDURMA

AIREND OUTLET TEMP. VIDA CIKIS SICAKLIGI

SCREW COMPRESSOR VIDALI KOMPRESOR

MAIN SCREEN SWITCH ANA EKRAN BUTONU

LOAD - UNLOAD SWITCH YUK - BOS BUTONU START SWITCH CALISTIRMA BUTONU

STOP SWITCH DURDURMA BUTONU

ELECTRONIC CONTROL SYSTEM ELEKTRONIK KONTROL SISTEMI !

PICTURE-3

Ask your dealer’s authorized personnel for the first start up. This will prevent your compressor from any possible damages. If you start up compressor on your own, ask your dealer the warranty conditions. For some cases your start up may infringe guarantee claims.

(7)

- DIMENSIONS ARE IN MM.

- ~: AVARAGE

NOT: You should leave 1000 mm

space in the both sides of the

compressor for service.

It is advised to use a water cooled

To Work ower 35ºC am bient

preaure.

!

COMPRESSOR 1500 mm WARM AIR OUTLET ~1000 mm ~1000 mm

PLACING OF THE COPMPRESSOR:

~1000 mm

COOLING AIR INLET (CLEAN AIR)

~1000 mm

PICTURE-4

(8)

8 /6 8 PICTURE-6 04 09 06 03 05 03 10 02 REF NO PERT NAME

SAMPLE INSTALLATION

09 09 01 02 08

!

01 02 03 04 05 06 07 08 09 10 WATER OIL 09

CHOOSE THE CORRECTLY SIZED PIPING SO THET THE TOTAL PRESSURE LOSS IN THE SYSTEM

WILL NOT EXCEED 1/10 BAR

09 07

(9)

INLET AND OUTLET AIR FLOW OF THE COMPRESSOR ROOM

PICTURE-7

AIR FLOW ENTERING TO THE COMPRESSOR ROOM

COMPRESSOR TYPE

INTAKE AIR FLOW (m³ /s)

VEK 20

1,65

VEK 30

1,65

VEK 40

2,70

VEK 50

2,70

TABLE-1

- ∆P must not be more than 15 mm. If ∆P is more than 15 mm, a new ventilation system must be designed. - This ventilation system must be designed in such a way that it can drain warm air from the system. - Cool air inlet must be higher than 1,5 fold from the section area of the warm air outlet.

- Paddlebox weight must not be overlaped the compressor.

- Bellows must be placed between paddlebox and compressor to prevent warm air leakage.

- Paddlebox must not be installed to the compressor, in this purpose a hole must not be made on the compressor.

SU

PICTURE 5 HOT AIR OUTLET

ABSORBER CLEAN AIR INLET CONCRETE FOUNDATION WATER M a x 1 5 m m

(10)

SAMPLE ELECTRIC INSTALLATION SCHEME

FUSE AND CABLE TYPES WHICH ARE USED IN THE ELECTRIC INSTALLATION

COMPRESSOR TYPE

FUSE

CABLE (TTR)

VEK 20

63 A

4 x 10

VEK 30

80 A

4 x 16

VEK 40

100 A

4 x 16

VEK 50

100A

4 x 16

YOU MUST DO THE GROUNDING

NEUTRAL LINE IS NOT GROUNDING

NOT: FUSE SELECTION IS IN COMPLIANCE WITH DIN 42673

USE AN UPPER CABLE SECTION IF THE DISTANCE IS OVER 50 M

CIRCUIT BREAKER FUSE TTR CABLE GROUNDING COMPRESSO R AIR DRYER COMPRESSOR PICTURE-8 TABLE-2

(11)

In picture A, you can see EASY 819 used in your new type of compressors and in picture B, you can see EASY 412 used in our older type of compressors.

PLC (control relay) exists in the panel control. PLC has several properties such as LCD screen, 24 volt, direct current and real time hourmeter. As seen in the panel control, several functions are carried out with the buttons (see picture c)

Operate your compressor by pushing the ‘’<’’ button. In this case, your compressor starts to produce air. In order for your compressor to stop, push the ‘’>’’ button. In this

case, your compressor firstly starts to work unload and after a very short time (30 seconds) stops. In order for your compressor to work manually load and unload , push the ‘ ’’’ button. When your compressor works on load , if you press ‘’ ’’ button, your compressor works unload. In another situation, when your compressor works unload, if you press ‘’ ´´ button, your compressor works normally.

In case you press the ‘’ ’’ button, all the information on the screen changes. If you press ‘’ ’’ button when compressor works on load; model properties, serial numbers, durations on total load and total unload come up. If you press ‘’ ’’ button again previous information is seen on the screen.

Also, some failures regarding working system of your compressor are seen on the PLC screen. For example, excessive temperature and high pressure on the compressor.

Do not use OK, ESC, DEL and ALT button because they are on the purpose of service and programming. PIC: C

OK,ESC,DEL AND ALT BUTTONS ARE IN THE PURPOSE OF SERVICE

AND PROGRAMMING AND THESE BUTTONS MUST NOT BE USED.

(12)

COMPRESSOR DIMENSION

COMPRESSOR TYPE

A

B

C

VEK 20

1845 880

720

VEK 30

1845 880

720

VEK 40

1845 880

720

VEK 50

1845 880

720

ALL DIMENSIONS ARE IN MM.

TABLE-3

(13)

~1000 mm AIR DRYER WARM AIR OUTLET - DIMENSIONS ARE IN mm. - ~: AVARAGE

NOT: YOU SHOULD LEAVE 1000 mm SPACE IN THE BOTH SIDES OF THE AIR DRAYER FOR SERVICE.

YOU MUST SELECT THE SUITABLE AIR DRYER ORDER TO WORK OVER 35°C AMBIENT TEMPERATURE

!

1500 mm

PICTURE 7

~1000 mm

COOLING AIR INLET (CLEAN AIR)

~500 mm

~1500 mm

COMPRESSOR ~500 mm

(14)

-

1475 SAYILI İŞ KANUNUNA GÖRE BASINÇLI KAPLAR MEVZUATI İÇ TÜZÜĞÜNE

UYGUN MEKANA GÜVENLİK ÖNLEMİ ALACAK ŞEKİLDE YERLEŞTİRİLMELİDİR.

-

DEPO İÇİNDE BİRİKEN SU HER GÜN BOŞALTILMALIDIR VEYA DEPO İÇİNE BİRİKEN

SUYU ALMAK İÇİN OTOMATİK TAHLİYE KULLANILMALIDIR.

!

!

SU TAHLIYESİ

HAVA DEPOSUNUN YERLEŞTİRİLMESİ:

~1000 mm

- INSTALLATION OF THE RECEIVER MUST BE DONE ACCORDING TO

LOCAL PROTECTION LAWS FOR PRESSURIZED VESSEL

- DRAIN THE ACCUMULATED WATER IN THE RECEIVER EVERYDAY OR USE

THE AUTOMATIC DRAIN FOR THIS PURPOSE

WATER DRAINAGE

PICTURE-12

(15)

PERIODICAL MAINTENANCE PROGRAM

CONTROLS AND MAINTENANCE THAT MUST BE DONE DAILY

1-) Compressor chamber

a-) Temperature

b-) Cleanliness

2-) Air pressure circuit

a-) Air leakage control

3-) Oil pressure circuit

a-) Oil leakage control

b-) Oil level control

4-) Electrical pneumatic circuit

a-) Heat control

5-) Airend

a-) Airend voice control

6-) Electrical motor

a-) Motor voice control

CONTROLS AND MAINTENANCES THAT MUST BE DONE DAILY

1-) Cleanliness of air filter ( from inside to outside with pressurized air)

2-) Inside cleanliness of compressor (*)

3-) Compressor cooler cleanliness (*)

4-) Control of working hourmeter (**)

5-) Control of current values

6-) Voltage control

7-) Control of belt tension

* Do not use water, thinner etc., abrasive or conductive cleanliness material.

** As soon as you realize that it is not working, inform to the Komsan Authorized

Service.

(16)

PERIODIC MAINTENANCE INTERVALS

TABLE-4

- Maintenance A and B are done by KOMSAN’S Technical Service at the place that the compressor is situated. - Maintenance C is done by KOMSAN in KOMSAN COMPRESSOR MANUFACTORING FACTORY or at the place that the compressor is situated.

- Maintenance D is done by KOMSAN in KOMSAN COMPRESSOR MANUFACTORING FACTORY

- You should make your compressor to have maintenance on time for the most efficiently working without any problems

- The user of the compressor must inform KOMSAN COMPRESSOR MANUFACTURING FACTORY or KOMSAN TECHNICAL SERVICE about the related time intervals shown above ; that the compressor is being used

- The time table that is given above is valid for normal conditions. The time table can differ according to the working conditions and the working area

- The earlier occured working time intervals for montly or hourly working time will be taken in to consideration for the maintanance duration time.

Institutions working 8

hours a day Institutions working 16 hours a day Institutions working 24 hours a day 6 Months or 1000 Hours Maintenance A 3 Months or 1000 Hours Maintenance A 2 Months or 1000 Hours Maintenance A 1 Year or 2000 Hours Maintenance A 6 Months or 2000 Hours

Maintenance A 4 Months or 2000 Hours

Maintenance A 2 Years or 4000 Hours

Maintenance B 12 Months or 4000 Hours Maintenance B 8 Months or 4000 Hours Maintenance B 3 Years or 6000 Hours

Maintenance A 18 Months or 6000 Hours Maintenance A 6 Months or 6000 Hours Maintenance A 4 Years or 8000 Hours

Maintenance A 24 Months or 8000 Hours Maintenance A 1 Year or 8000 Hours Maintenance A 5 Years or 10000 Hours Maintenance C 30 Months or 10000 Hours Maintenance C 20 Months or 10000 Hours Maintenance C 6 Years or 12000 Hours

Maintenance A 36 Months or 12000 Hours Maintenance A 24 Months or 12000 Hours Maintenance A 7 Years or 14000 Hours Maintenance A 42 Months or 14000 Hours Maintenance A 28 Months or 14000 Hours Maintenance A 8 Years or 16000 Hours Maintenance B 48 Months or 16000 Hours Maintenance B 32 Months or 16000 Hours Maintenance B 9 Years or 18000 Hours

Maintenance A 54 Months or 18000 Hours Maintenance A 36 Months or 18000 Hours Maintenance A 10 Years or 20000 Hours

(17)

BREAKDOWN PROBABLE REASONS WAYS TO REPAIR

Overload relay is out of order Change Electric engine or screw bearings are out of order Call service

Star-delta transition time is short Regulate and push the reset button

Off loading time is very short Regulate Contactors are out of order or sticked Change Overload relay or fuse

burns

Fuses are burned Change

Working pressure interval is wrong Regulate Pressure switch is out of order Change Solenoid valve coil is burned Change

Call service Change contactor Electrical system is breakdown

Change contactor Change the cracked Control air control hoses

or crushed ones Air control hose connections could have been dirty ( After maintenance, sealing components could block

the connections )

Clean Compressor can not be

loaded

Solenoid valve is dirtied Clean

Air filter is blocked Change air filter Separator is blocked Change separator Air intake setting valve is breakdown Call service Air efficiency is not

enough

Excessive air consumption exists. The cross-section of pipes of Air connection is narrow.

Control installation leakage and air consumption of pneumatic tools

Oil hoses are blocked Change There is foam on oil Wrong oil usage Expiry date of oil has long been passed Change Cooler is blocked or dirty Clean cooler

Cooling air is not enough Change the inlet and outlet air Termostatic valve does not work Call service

Ambient temperature is very high (max 35 C) or ventilation is not enough.

Be careful about not being leakage in the suction and pumping chimney-hoods. Make chimney-hood and ventilation installation to make ambient temperature decrease.

Lamp and relay are out of order Control Compressor heats

excessively. (Outlet air +100 C , warning lamp lights.)

Fan blower blades are not strong Change Oil turning pipe is blocked Open and clean Separator is blocked or out of order Change Excessive oil

consumption Wrong oil usage or oil expiry date has long been passed.

Change the oil with oil filter and use the suitable oil

Pressure switch is breakdown Change The setting of pressure switch has not been done Set Pressure is increasing

excessively.

Air intake setting valve is breakdown Call service

If a cabinet filter mounted on the compressor you should change it free of charge.

(18)

THE MAINTENANCE THAT MUST BE DONE BY THE USER

1- To check the electrical connections; to check the connections whether they are loose or not, while the switch is closed.

2- Air circuit problems; the control of the air leaks and the pneumatic circuit elements.

3- To protect your compressor against the outer effects; you should keep your compressor away from dirty surroundings and if it is necessary you should build a separate compressor room.

4- To check the thermic, fuse and voltage.

5- To clean the cooler; the cooler must be cleaned with compressed air from its inner side to its outer side. 6- To clean the oil return line; to clean the filter in the oil return check valve.

7- To check the belt tightness; once a week you should check the belt tightness. 8- To arrange the pressure level

9- To clean the air filter; the air filter should be disassembled and cleaned with compressed air from its inner side to its outer side.

10-To check the operating hour meter; whether the operating hour meter is working or not while the compressor is working; if the hour meter is not working you must call immediately the KOMSAN technical service.

If the technical service is called, because of the reasons above and things stated in the breakdown finding page, a service expense is paid to KOMSAN.If a brekdown occurs because of not doing the cleaning and maintenance stated above, while your compressor is working your compressor will be out of guarantee.

The first start of the compressor process and all the maıntenance will be done in the guarantee period; the maintenance except the things stated above and in the breakdown finding page must be done by KOMSAN technical service. In an opposite occasion the compressor will be out of guarantee.

The adress that the compressor is situated : CUSTOMER/Cachet

PHONE NUM : DATE : SIGNATURE :

(19)

ATTENTION TO THE SERVICE AFTER SALE

FIRST OPERATING INSTRUCTIONS

DATE : .../.../ 200...

TYPE OF THE COMPRESSOR : ... SERI NO : ...

KOMSAN A.Ş. FAX : +90 (212) 728 70 23

THE PROCESSES THAT MUST BE DONE BEFORE CALLING THE KOMSAN TECHNICAL SERVICE FOR THE FIRST START OF THE COMPRESSOR

YES NO 1-1 Are the compressor and equipments installed as shown in the guide book?

1-2 Is the air installation correctly completed according to the type of the compressor?

1-3 Is the electrical installition completed as shown in the guide book?

1-4 Is the electrical volt value,cable type,quality.fuse,thermic switch;suitable to the motor power and the empty space occupied between the compressor and the power resource? (Please look at the maintenance guide)

1-4-1 Is the volt entrance suitable to compressor and the compressedair equipments working with electric?

1-5 Is there a ventilation system established?

The processes stated above are done by us. We request the first start and the begin of guarantee applications of the compressor to be done by KOMSAN compressor manufactorıng factory.

The adress that the compressor is situated : CUSTOMER/ Cachet

PHONE NUMBER : DATE :

SIGNATURE :

NOTE: If our service technician that will come to your institution, sees some uncompleted processes, then our

service will not do the first start. After the needed processes are completed the service will come to your institution again and will do the first start by getting the service expences from you.

If you want to get detailed information about the things above, you can call; +90 212 728 43 43 or comminicate with us by fax from +90 212 728 70 23 and reach us servis@komsan.com.tr.

(20)

YEDEK PARÇA

LİSTESİ

SPARE PART

LIST

(21)
(22)

VEK 20-50 ANA MONTAJ

VEK 20-50 MAIN ASSEMBLY

Sıra No/Ref. No Parça No/Series No Sayfa No/Page No Adı Name

01 154.66.904 34 Kaporta Grubu Bonnet Group

02 154.45.101 44 Gösterge Grubu Instrument Panel Group 03 154.47.102 36 Pnömatik Grubu Pneumatic Group 04 154.42.301 40 Elektrik Grubu Electrical Group 05 154.47.003 20 Hidrolik Grubu Hydrolic Group 06 154.00175.001 24 Vida Grubu Air End Group

(23)
(24)

154.32.939 1 Vek 40-50 Boru Tak. Hose Team

14 154.60.820 1 Yağ Deposu Montajı Oil Receiver Assembly

15 154.28.231 2 Rakor Nipple

16 154.56.111 1 Seperatör Separator

17 154.03.603 1 Seperatör kapağı Separator Cover

18 154.28.011 1 Nipel Nipple

19 154.50.014 1 Min. Basınç Valfi (Vek 20-30) Min. Presure Valve 154.50.022 1 Min. Basınç Valfi (Vek 40-50) Min. Presure Valve

HİDROLİK GRUBU

HYDROLIC GROUP - 154.47.003

Sıra No/Ref. No Parça No/Series No Adet/Quantity Parça Adı Part Name

01 154.62.004 1 Soğutucu Cooler

02 154.28.210 5 Nipel Nipple

03 154.32.030 1 Boru Hose

04 154.32.030 1 Boru Hose

05 154.50.057 1 Termostatik Valf Thermostatic Valve

06 154.28.158 2 Nipel Nipple

07 154.03.601 1 Filtre Kapağı Filter Cover

08 154.32.301 1 Boru Hose

09 154.56.606 1 Filtre Filter

10 154.28.234 2 Rakor Nipple

11 154.32.903 2 Nipel Nipple

12 154.00175.001 1 Vida Ünitesi Airend 13 154.32.938 1 Vek 20-30 Boru Tak. Hose Team

(25)
(26)

MOTOR GRUBU

MOTOR GROUP - 154.10.820

Sıra No/Ref. No Parça No/Series

No Adet/Quant. Parça Adı Part Name

01 154.00175.001 1 Vida Ünitesi Air End

02 154.19.023 1 Kama Wedge

03 154.10.026 1 Kama (Vek 20) Wedge (Vek 20) 154.10.022 1 Kama (Vek 30) Wedge (Vek 30) 154.10.230 1 Kama (Vek 40) Wedge (Vek 40) 154.10.237 1 Kama (Vek 50) Wedge (Vek 50)

04 154.23.061 4 Somun Nut

05 154.27.024 8 Pul Washer

06 154.22.097 4 Civata Bolt

07 154.04.006 1 Kasnak (Vek 20-7.5 bar) Pulley (Vek 20-7.5 bar) 154.04.006 1 Kasnak (Vek 20-10 bar) Pulley (Vek 20-10 bar) 154.04.006 1 Kasnak (Vek 20-13 bar) Pulley (Vek 20-13 bar) 154.04.062 1 Kasnak (Vek 30-7.5 bar) Pulley (Vek 30-7.5 bar) 154.04.054 1 Kasnak (Vek 30-10 bar) Pulley (Vek 30-10 bar) 154.04.033 1 Kasnak (Vek 30-13 bar) Pulley (Vek 30-13 bar) 154.04.006 1 Kasnak (Vek 40-7.5 bar) Pulley (Vek 40-7.5 bar) 154.04.038 1 Kasnak (Vek 40-10 bar) Pulley (Vek 40-10 bar) 154.04.086 1 Kasnak (Vek 40-13 bar) Pulley (Vek 40-13 bar) 154.04.086 1 Kasnak (Vek 50-7.5 bar) Pulley (Vek 50-7.5 bar) 154.04.006 1 Kasnak (Vek 50-10 bar) Pulley (Vek 50-10 bar)

154.04.115 1 Kasnak (Vek 50-10 bar – 1500 dev/dak) Pulley (Vek 50-10 bar – 1500 rpm) 154.04.091 1 Kasnak (Vek 50-13 bar) Pulley (Vek 50-13 bar)

154.04.115 1 Kasnak (Vek 50-13 bar – 1500 dev/dak) Pulley (Vek 50-13 bar – 1500 rpm) 08 154.15.119 1 Kas.Göb.(Vek 20-7.5 bar) Tapper Lock Bushing(Vek 20-7.5 bar)

154.15.119 1 Kas.Göb. (Vek 20-10 bar) Tapper Lock Bushing(Vek 20-10 bar) 154.15.119 1 Kas.Göb. (Vek 20-13 bar) Tapper Lock Bushing(Vek 20-13 bar) 154.15.807 1 Kas.Göb.(Vek 30-7.5 bar) Tapper Lock Bushing(Vek 30-7.5 bar) 154.15.807 1 Kas.Göb. (Vek 30-10 bar) Tapper Lock Bushing(Vek 30-10 bar) 154.15.807 1 Kas.Göb. (Vek 30-13 bar) Tapper Lock Bushing(Vek 30-13 bar) 154.15.119 1 Kas.Göb.(Vek 40-7.5 bar) Tapper Lock Bushing(Vek 40-7.5 bar) 154.15.119 1 Kas.Göb. (Vek 40-10 bar) Tapper Lock Bushing(Vek 40-10 bar) 154.15.807 1 Kas.Göb. (Vek 40-13 bar) Tapper Lock Bushing(Vek 40-13 bar) 154.15.807 1 Kas.Göb.(Vek 50-7.5 bar) Tapper Lock Bushing(Vek 50-7.5 bar) 154.15.119 1 Kas.Göb. (Vek 50-10 bar) Tapper Lock Bushing(Vek 50-10 bar) 154.15.156 1 Kas.Göb. (Vek 50-10 bar – 1500dev/dak) Tapper Lock Bushing(Vek 50-10 bar – 1500rpm) 154.15.119 1 Kas.Göb. (Vek 50-13 bar) Tapper Lock Bushing(Vek 50-13 bar)

(27)

MOTOR GRUBU

MOTOR GROUP - 154.10.820

Sıra No/Ref. No Parça No/Series No Adet/Quant. Parça Adı Part Name

154.15.156 1 Kas.Göb. (Vek 50-13 bar – 1500 dev/dak) Tapper Lock Bushing (Vek 50-13 bar – 1500 rpm) 09 154.15.119 2 Setskur.(Vek 20-7.5 bar) Set Screw(Vek 20-7.5 bar) 154.15.119 2 Setskur. (Vek 20-10 bar) TSet Screw(Vek 20-10 bar) 154.15.119 2 Setskur. (Vek 20-13 bar) Set Screw(Vek 20-13 bar) 154.15.156 2 Setskur.(Vek 30-7.5 bar) Set Screw(Vek 30-7.5 bar) 154.15.807 2 Setskur. (Vek 30-10 bar) Set Screw(Vek 30-10 bar) 154.15.119 2 Setskur. (Vek 30-13 bar) Set Screw(Vek 30-13 bar) 154.15.119 2 Setskur.(Vek 40-7.5 bar) Set Screw(Vek 40-7.5 bar) 154.15.807 2 Setskur. (Vek 40-10 bar) Set Screw(Vek 40-10 bar) 154.15.807 2 Setskur. (Vek 40-13 bar) Set Screw(Vek 40-13 bar) 154.15.119 2 Setskur.(Vek 50-7.5 bar) Set Screw(Vek 50-7.5 bar) 154.15.119 2 Setskur. (Vek 50-10 bar) Set Screw(Vek 50-10 bar) 154.15.119 2 Setskur. (Vek 50-13 bar) Set Screw(Vek 50-13 bar)

10 154.22.007 5 Civata Bolt

11 154.21.040 1 Pervane Göbeği Fan Hub

12 154.21.043 2 Pervane Bağlantı Parçası Blade Assembly Tool

13 154.21.009 10 Kanat Blade

14 154.10.026 1 Motor (Vek 20) Motor (Vek 20) 154.10.022 1 Motor (Vek 30) Motor (Vek 30) 154.10.230 1 Motor (Vek 40) Motor (Vek 40) 154.10.237 1 Motor (Vek 50) Motor (Vek 50)

15 154.22.097 8 Civata Bolt

16 154.27.024 16 Pul Washer

17 154.66.423 1 Gönye Direği Montajı Gönye Direği Montajı

18 154.23.015 8 Somun Nut

19 154.04.060 1 Kasnak (Vek 20-7.5 bar) Pulley (Vek 20-7.5 bar) 154.04.116 1 Kasnak (Vek 20-10 bar) Pulley (Vek 20-10 bar) 154.04.091 1 Kasnak (Vek 20-13 bar) Pulley (Vek 20-13 bar) 154.04.108 1 Kasnak (Vek 30-7.5 bar) Pulley (Vek 30-7.5 bar) 154.04.060 1 Kasnak (Vek 30-10 bar) Pulley (Vek 30-10 bar) 154.04.060 1 Kasnak (Vek 30-13 bar) Pulley (Vek 30-13 bar) 154.04.113 1 Kasnak (Vek 40-7.5 bar) Pulley (Vek 40-7.5 bar) 154.04.113 1 Kasnak (Vek 40-10 bar) Pulley (Vek 40-10 bar) 154.04.098 1 Kasnak (Vek 40-13 bar) Pulley (Vek 40-13 bar)

(28)

MOTOR GRUBU

MOTOR GROUP - 154.10.820

Sıra No/Ref. No Parça No/Series

No Adet/Quant. Parça Adı Part Name

154.04.060 1 Kasnak (Vek 50-13 bar) Pulley (Vek 50-13 bar)

154.04.136 1 Kasnak (Vek 50-13 bar – 1500dev/dak) Pulley (Vek 50-13 bar – 1500rpm)

20 154.15.155 1 Kas.Göb.(Vek 20-7.5 bar) Tapper Lock Bushing(Vek 20-7.5 bar) 154.15.118 1 Kas.Göb. (Vek 20-10 bar) Tapper Lock Bushing(Vek 20-10 bar) 154.15.118 1 Kas.Göb. (Vek 20-13 bar) Tapper Lock Bushing(Vek 20-13 bar) 154.15.126 1 Kas.Göb.(Vek 30-7.5 bar) Tapper Lock Bushing(Vek 30-7.5 bar) 154.15.126 1 Kas.Göb. (Vek 30-10 bar) Tapper Lock Bushing(Vek 30-10 bar) 154.15.126 1 Kas.Göb. (Vek 30-13 bar) Tapper Lock Bushing(Vek 30-13 bar) 154.15.312 1 Kas.Göb.(Vek 40-7.5 bar) Tapper Lock Bushing(Vek 40-7.5 bar) 154.15.312 1 Kas.Göb. (Vek 40-10 bar) Tapper Lock Bushing(Vek 40-10 bar) 154.15.113 1 Kas.Göb. (Vek 40-13 bar) Tapper Lock Bushing(Vek 40-13 bar) 154.15.312 1 Kas.Göb.(Vek 50-7.5 bar) Tapper Lock Bushing(Vek 50-7.5 bar) 154.15.312 1 Kas.Göb. (Vek 50-10 bar) Tapper Lock Bushing(Vek 50-10 bar) 154.15.160 1 Kas.Göb. (Vek 50-10 bar 1500dev/dak) Tapper Lock Bushing(Vek 50-10 bar -1500rpm) 154.15.312 1 Kas.Göb. (Vek 50-13 bar) Tapper Lock Bushing(Vek 50-13 bar) 154.15.160 1 Kas.Göb. (Vek 5013 bar

-1500dev/dak)

Tapper Lock Bushing(Vek 50-13 bar – 1500 rpm)

21 154.15.155 2 Setskur.(Vek 20-7.5 bar) Set Screw(Vek 20-7.5 bar) 154.15.118 2 Setskur. (Vek 20-10 bar) TSet Screw(Vek 20-10 bar) 154.15.118 2 Setskur. (Vek 20-13 bar) Set Screw(Vek 20-13 bar) 154.15.126 2 Setskur.(Vek 30-7.5 bar) Set Screw(Vek 30-7.5 bar) 154.15.126 2 Setskur. (Vek 30-10 bar) Set Screw(Vek 30-10 bar) 154.15.126 2 Setskur. (Vek 30-13 bar) Set Screw(Vek 30-13 bar) 154.15.312 2 Setskur.(Vek 40-7.5 bar) Set Screw(Vek 40-7.5 bar) 154.15.312 2 Setskur. (Vek 40-10 bar) Set Screw(Vek 40-10 bar) 154.15.113 2 Setskur. (Vek 40-13 bar) Set Screw(Vek 40-13 bar) 154.15.312 2 Setskur.(Vek 50-7.5 bar) Set Screw(Vek 50-7.5 bar) 154.15.312 2 Setskur. (Vek 50-10 bar) Set Screw(Vek 50-10 bar) 154.15.312 2 Setskur. (Vek 50-13 bar) Set Screw(Vek 50-13 bar) 22 154.14.919 4 Kayış (Vek 20-7,5 bar) Belt (Vek 20-7,5 bar)

154.14.024 4 Kayış (Vek 20-10 bar) Belt (Vek 20-10 bar) 154.14.922 4 Kayış (Vek 20-13 bar) Belt (Vek 20-13 bar) 154.14.041 4 Kayış (Vek 30-7.5 bar) Belt (Vek 30-7.5 bar) 154.14.041 4 Kayış (Vek 30-10 bar) Belt (Vek 30-10 bar) 154.14.919 4 Kayış (Vek 30-13 bar) Belt (Vek 30-13 bar) 154.14.919 4 Kayış (Vek 40-7.5 bar) Belt (Vek 40-7.5 bar)

(29)

154.14.919 4 Kayış (Vek 40-10 bar) Belt (Vek 40-10 bar) 154.14.919 4 Kayış (Vek 40-13 bar) Belt (Vek 40-13 bar) 154.14.919 4 Kayış (Vek 50-7.5 bar) Belt (Vek 50-7.5 bar) 154.14.919 4 Kayış (Vek 50-10 bar) Belt (Vek 50-10 bar)

154.14.025 5 Kayış (Vek 50-10 bar – 1500 dev/dak) Belt (Vek 50-10 bar – 1500 rpm) 154.14.919 4 Kayış (Vek 50-13 bar) Belt (Vek 50-13 bar)

(30)
(31)

VİDA GRUBU

AIREND GROUP - 154.00175.800

Sıra No/Ref. No Parça No/Series No Adet/Quantity Parça Adı Part Name

01 154.23.023 1 Somun Nut

02 154.56.036 1 Filtre Kabı Cover

03 154.56.100 1 Filtre Fitler 04 154.32.301 1 Nipel Nipple 05 154.22.202 4 Civata Bolt 06 154.23.009 4 Somun Nut 07 154.27.043 4 Pul Washer 08 154.22.904 4 Civata Bolt 09 154.22.260 4 Civata Bolt

10 154.39.902 1 Emiş Valfi Montajı Intake Valve Assembly

11 154.16.919 1 O-Ring O-Ring

12 154.19.077 1 Kama Wedge

13 154.28.279 1 Nipel Nipple

14 154.28.279 1 Süzgeç Strainer

15 154.50.004 1 Çekvalf Check Valve

16 154.28.463 1 Dirsek Elbow

17 154.22.202 4 Cıvata Bolt

18 154.13.035 1 Termometer Orifice

19 154.22.008 10 Civata Bolt

20 154.00175.001 1 Vida Ünitesi Air End

(32)
(33)

YAĞ DEPOSU

OIL RECEIVER - 154.60.820

Sıra No/Ref. No Parça No/Series No Adet/Quantity Parça Adı Part Name

01 154.28.295 1 Rakor Nipple

02 154.28.304 1 Nipel Nipple

03 154.28.065 2 Kör Tapa Plug

04 154.60.940 1 Yağ deposu Montajı Oil Receiver Assembly 05 154.52.012 1 Emniyet Subabı Safety Valve

06 154.35.004 2 Dirsek Elbow 07 154.00175.304 1 Conta Gasket 08 154.32.059 1 Hortum Hose 09 154.60.820 1 Dirsek Elbow 10 154.58.054 1 Boru Hose 11 154.28.253 1 Ayak Flange

(34)
(35)

HAVA EMİŞ VALFİ

AIR INLET VALVE - 154.39.902

Sıra No/Ref. No Parça No/Series No Adet/Quantity Parça Adı Part Name

01 154.01.046 1 Gövde Frame 02 154.16.919 1 O-Ring O-Ring 03 154.24.035 1 Yay Spring 04 154.23.016 1 Somun Nut 05 154.16.042 1 Halka Ring 06 154.49.023 1 Piston Piston 07 154.16.916 1 Keçe Seal 08 154.19.032 1 Mil Pin 09 154.16.321 1 O-Ring O-Ring

10 154.15.110 1 Yatak İnnerr Part

11 154.16.034 1 O-Ring O-Ring

12 154.15.137 1 Burç Bushing

13 154.46.022 1 Segman Piston Ring

14 154.24.010 1 Yay Spring

15 154.15.138 1 Burç Bushing

16 154.68.004 1 Klape Clamp

17 154.16.916 1 Conta Gasket

18 154.26.040 1 Segman Piston Ring

19 154.16.920 2 O-Ring O-Ring

20 154.28.061 1 Kovan Cover

21 154.28.072 1 Kovan Cover

(36)
(37)

MİNİMUM BASINÇ VALFİ

MINUMUM PRESSURE VALVE - 154.50.014

Sıra No/Ref. No Parça No/Series No Adet/Quantity Parça Adı Part Name

01 154.22.466 1 Setskur Set Screw

02 154.23.002 1 Somun Nut 03 154.26.026 1 Pul Washer 04 154.01.048 1 İç Gövde Cylinder 05 154.16.028 1 Oring O-ring 06 154.50.801 1 Stoper Stopper 07 154.24.046 1 Yay Spring 08 154.03.011 1 Kapak Cover 09 154.16.023 1 O-ring O-ring 10 154.24.045 1 Yay Spring 11 154.49.033 1 Piston Piston 12 154.16.011 1 O-ring O-ring

13 154.22.449 1 Setskur Set Screw

(38)
(39)

MİNİMUM BASINÇ VALFİ

MINUMUM PRESSURE VALVE - 154.50.022

Sıra No/Ref. No Parça No/Series No Adet/Quantity Parça Adı Part Name

01 154.22.171 1 Cıvata Bolt 02 154.23.018 1 Somun Nut 03 154.01.051 1 İç Gövde Cylinder 04 154.16.138 1 O-ring O-ring 05 154.50.802 1 Stoper Stopper 06 154.24.047 1 Yay Spring 07 154.24.048 1 Yay Spring 08 154.03.012 1 Kapak Cover 09 154.16.088 1 Keçe Seal

10 154.03.013 1 Piston Kapağı Piston Cover

11 154.22.118 1 Cıvata Bolt

12 154.24.049 1 Yay Spring

13 154.49.034 1 Piston Piston

14 154.16.036 1 O-ring O-ring

15 154.01.052 1 Gövde Body

(40)
(41)

TERMOSTATİK VALF

THERMOSTATIC VALVE - 154.50.057

Sıra No/Ref. No Parça No/Series No Adet/Quantity Parça Adı Part Name

01 154.26.906 1 Segman Circlip 02 154.03.071 1 Kapak Cover 03 154.16.061 1 O-ring O-ring 04 154.40.620 1 Müşür Gage 05 154.49.029 1 Piston Piston 06 154.24.022 1 Yay Spring 07 154.50.057 1 Gövde Body

(42)
(43)

KAPORTA GRUBU

BONNET GROUP - 154.66.424

Sıra No/Ref. No Parça No/Series No Adet/Quantity Parça Adı Part Name

01 154.66.426 2 Yan Kapak Side Plate

02 154.66.444 1 Elektrik Panosu Electrical Panel Sheet

03 154.66.450 1 Tavan Sacı Cover Plate

04 154.64.116 1 Dav. Borusu (Vek 20) Chimney Hood (Vek 20) 154.64.116 1 Dav. Borusu (Vek 30) Chimney Hood (Vek 30) 154.64.116 1 Dav. Borusu (Vek 40-50) Chimney Hood (Vek 40-50) 05 154.64.115 1 Davlumbaz Borusu Göv. Scarfed Sheet Cover 06 154.66.447 1 Arka Kapama Sacı Back Cover Plate

07 154.66.433 1 Izgara Protecting Plate

08 154.66.435 1 Gövde Body

09 154.64.048 2 Filtre Filter

10 154.66.425 1 Pano Kapağı Panel Sheet Panel

11 154.28.290 7 Kapak Kilidi Cover Key

12 154.28.293 1 Kilit Anahtarı Lock Key

13 154.66.427 1 Ön Kapak Front Plate

14 154.28.248 4 Menteşe Hinge

15 154.66.449 1 Sol Direk Left Column

16 154.66.448 1 Sağ Direk Right Column

17 154.66.446 1 Ara Bağlantı Parçası Beam

18 154.66.418 1 Kapak Plate

19 154.22.033 4 Civata Bolt

20 154.22.005 8 Civata Bolt

21 154.27.305 8 Pul Washer

22 154.66.451 1 Taban Sacı Bottom Plate

23 154.28.030 4 Lastik Takoz Rubber Block

24 154.23.013 4 Somun Nut

(44)

1 0 1 3 1 7 1 2 1 1 B 4

(45)

PNÖMATİK GRUBU

PNEUMATIC GROUP - 154.47.102

Sıra No/Ref. No Parça No/Series No Adet/Quantity Parça Adı Part Name

01 154.00175.001 1 Vida Ünitesi Air End

02 154.39.902 1 Emiş Valfi IntakeValve

03 154.50.004 2 Çek Valf Check Valve

04 154.40.023 1 Ters Dönüş Müşürü Anti Rotation Swich 05 154.40.037 1 Basınç Sensörü Pressure Sensor 06 154.42.050 1 Selenoid Valf 2NA Solenoid Valve 2NA 07 154.42.089 1 Selenoid Valf 2NK Solenoid Valve 2NA 08 154.42.024 1 Selenoid Valf 3NK Solenoid Valve 3NA

09 154.60.820 1 Yağ Deposu Oil Receiver

10 154.56.111 1 Seperatör Separator

11 154.50.014

154.50.022

1 1

Min Basınç Valfi (Vek 20-30) Min Basınc Valfi (Vek 40-50)

Minumum Presure Valve

Minumum Presure Valve

12 154.28.278 1 Orifis (Vek 20-30-40) Orifice (Vek 20-30-40) 154.28.277 1 Orifis (Vek 50) Orifice (Vek 50)

13 154.52.012 1 Emniyet Subabı Safety Valve

14 154.50.057 1 Termostatik Valf Thermostatic Valve

15 154.56.606 1 Filtre Filter

16 154.62.004 1 Soğutucu Cooler

(46)

The Screw Compressor’s Hydro-Pneumatic Cycle and Working Principle

Compressor working onload: The compressor starts with star contactor and then delta contactor and

required energy is provided in order for compressor to start. Airend (1) is driven by electrical motor. With the rotation of the rotors in the airend , a vacuum environment is created. This vacuum environment enable the compressed air goes through the rotors meshing each other to the outlet port.

The compressed air which is mixed with oil, inside the airend, leaves the airend with the impact of the high pressure and is sprayed to the separator tank’s (oil receiver’s) (10) upper section. Inside the separator the oil in the air is accumulated at the bottom of the oil receiver. Under the high pressure conditions, the oil leaves the oil receiver and enters in the thermostatic valve. At this part of the cycle according to the oil’s temprature the oil directly passes from the thermostatic valve(15) to the airend, through the oil filter or goes to the cooler (17) just after passing the thermostatic valve. After the oil is cooled in the cooler, it enters in the oil filter (16) and returns back to the rotors that are working together, to decrease the increasing heat produced by the rotors and to prevent the compressed air escaping backwards.

In the separator tank(oil receiver) firstly the oil is partly separated. In the second step the oil passes to the separator(11) in which the air is completely separated from oil. After the separation of the oil from air, the air passes through the minimum pressure valve(12) and enters in the cooler in which air is cooled and be ready to be served. On the other hand the oil inside the separator tank is pushed to the airend by passing through check valve (3) and orifice (13) with the impact of the high pressure.

Compressor working unloading: As soon as the pressure level of the compressor reaches to the desired

level, solenoid valve (7) goes into closed position from open position after pressure switch (6) starts to work. Then, air intake valve closes. As for pressurized air in separator tank, a little portion of pressurized air in separator tank goes to the airend by passing through solenoid valve (7) , remaining part of the pressurized air gets out of the system by passing through intake valve.

If any air demand emerges when the compressor works unload, pressure switch enable solenoid valve to open position. Therefore, compressor again starts to produce compressed air.

Compressor’s stop: In case no need of compressed air in the system while the compressor working

unload , electrical motor stops after the time controlled by PLC.

Compressor resumes to work: When the compressor’s pressure decreases to designated level,

pressure switch starts to work. After a while, the compressor start to work again to produce compressed air after getting current to its electrical motor from the system.

(47)

1 2 + 2 4 V 7 0 ,5 / 4 ,5 1 P 8 E R C IR C U IT ~ 2 2 IN P U T S 0 4 3 ∆ Line Contaactor 2 3 1 3 1 Selenoid Valve No Load Star contactor Delta contactor Selenoid Valve Transfer air into Airend Selenoid Valve Discharge

(48)

ELEKTRİK GRUBU

ELECTRICAL GROUP - 154.42.058

Sıra No/Ref. No Parça No/Series No Adet/Quantity Parça Adı Part Name

01 154.110.017 1 Acil Stop Butonu Emergency Stop Button

02 154.43.496 1 Besleme Kartı Supply Card

03 154.43.551 1 PLC PLC

04 154.100.019 1 Hat Kontaktörü (Vek 20) Line Contactor (Vek 20) 154.43.554 1 Hat Kontaktörü (Vek 30) Line Contactor (Vek 30) 154.43.006 1 Hat Kontaktörü (Vek 40) Line Contactor (Vek 40) 154.43.002 1 Hat Kontaktörü (Vek 50) Line Contactor (Vek 50) 154.43.004 1 Yıldız Kontaktör (Vek 20) Star Contactor (Vek 20) 05 154.100.019 1 Yıldız Kontaktör (Vek 30) Star Contactor (Vek 30) 154.43.554 1 Yıldız Kontaktör (Vek 40) Star Contactor (Vek 40) 154.43.554 1 Yıldız Kontaktör (Vek 50) Star Contactor (Vek 50) 154.100.019 1 Üçgen Kontaktör (Vek 20) Delta Contactor (Vek 20)

154.43.554 1 Üçgen Kontaktör (Vek 30) Delta Contactor (Vek 30) 06 154.43.006 1 Üçgen Kontaktör (Vek 40) Delta Contactor (Vek 40) 154.43.002 1 Üçgen Kontaktör (Vek 50) Delta Contactor (Vek 50) 07 154.42.011 1 Selenoid Valf Solenoid Valve

08 154.43.700 1 Termik Röle (Vek 20) Thermic Relay (Vek 20) 154.43.703 1 Termik Röle (Vek 30) Thermic Relay (Vek 30) 154.43.703 1 Termik Röle (Vek 40) Thermic Relay (Vek 40) 154.43.702 1 Termik Röle (Vek 50) Thermic Relay (Vek 50)

09 154.43.497 1 Trafo Transformer

10 154.41.336 2 Kontaktör Yardımcı Bloğu Contactor Auxiliary Block

11 154.100.018 1 alter Circuit Breaker

(49)

49

/6

8

LOAD - UNLOAD SWITCH YUK - BOS BUTONU MAIN SCREEN SWITCH

ANA EKRAN BUTONU START SWITCH CALISTIRMA BUTONU EMERGENCY STOP ACIL DURDURMA STOP SWITCH DURDURMA BUTONU

!

ELECTRONIC CONTROL SYSTEM

ELEKTRONIK KONTROL SISTEMI easy

SCREW COMPRESSOR VIDALI KOMPRESOR

AIREND OUTLET TEMP. VIDA CIKIS SICAKLIGI

VEK20/50

1 5 4 2 3 6

(50)

GÖSTERGE GRUBU

INSTRUMENT PANEL GROUP - 154.45.101

Sıra No/Ref. No Parça No/Series No Adet/Quantity Parça Adı Part Name

01 154.43.551 1 PLC PLC

02 154.13.035 1 Termometre Thermometer

03 154.45.004 1 Etiket Label

04 154.45.008 1 Etiket Label

05 154.110.017 1 Acil Stop Butonu Emergency Stop Button

(51)

SERVİS

BİLGİLERİ

SERVICE

INFORMATIONS

(52)

09 FRM 017

Rev 00

29.04.2005

KOMPRESÖR BAKIM TAKİP KARTI

KOM PRES ÖR TİPİ : S ERİ NO :

TARİHLER YAPILAN PERİYODİK BAKIM VEYA GİDERİLEN ARIZANIN

TANIM I

RAPOR NO BAKIM I YAPAN ARIZAYI GİDEREN BAŞ LANGIÇ BİTİŞ

(53)

References

Related documents

The results of my investigation in MDMs showed that MMP-1 gene expression and secretion were significantly increased and was functionally active in M.tb-infected human

Makeup case &amp; Briefcase: Compressor, airbrush, and colors can be selected

Therefore, I considered a sample of eight secondary schools sufficiently rigorous for this study (Patton, 2002). The study involved 48 Year 8 students aged 12 – 13, drawn from

COMPLETE AIR COMPRESSOR AIR COMP.. COMPLETE

Connect the pressure switch to the air compressor using the large white wire (Load) from the pressure switch and the red wire (12V DC Source) from the air compressor.. Ground the

According to uncovered interest parity, a relative increase in the Norwegian money market interest rate is offset by a lower expectation for Norwegian currency (a higher exchange

Insert one end of Large Diameter Air Hose onto Low Pressure Inflator Outlet and appropriate plastic air hose inflator adapter onto other end2. Plug Power Cord into a DC

This study has, therefore, evaluated the relevance of BMI to suicidal ideation and self-harming behavior after controlling for body weight perception (BWP) and other