P/N-no.: M1203124 SDS-ID: US/8.0
IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING
1.
REPLISET-F5, -F1, -T3, -T1, -GF1, -GT1 For3D or metallographic replica For 3D or metallographic replica Product name: Application: Struers A/S Pederstrupvej 84 DK-2750 Ballerup Tel: +45 44 600 800 Supplier: 50; 265 ml Container size: Infotrac: 1-800-535-5053 Struers US: 1-440-871-0071 Emergency telephone: [email protected]
Responsible for safety data sheet authoring:
HAZARDS IDENTIFICATION
2.
The product is not classified.
Human health: May cause minor irritation on eye contact.
Environment: The product is not expected to be hazardous to the environment.
COMPOSITION/INFORMATION ON INGREDIENTS
3.
The product contains:
Trace of chloroplatinic acid impurity.
%: CAS-No.: EC No.: Chemical name: Hazard classification: Notes:
Polymethylvinylsiloxane 67762-94-1 1-20 - -Polymethoxyvinylsiloxane 68037-85-4 1-20 - -Polymethylhydrogenosiloxane 68037-59-2 1-20 - -Polyorganosiloxane 63148-53-8 1-10 - -Silicone oxide 11126-22-0 1-10 234-368-0 -Polyoxymethylene diacetate 25231-38-3 1-10 - -Silica 60676-86-0 1-10 262-373-8 -Platinum, complexes 68412-56-6 1-10 270-195-7
-FIRST-AID MEASURES
4.
Inhalation: Unlikely route of exposure as the product does not contain volatile substances.
Skin contact: Remove contaminated clothes and rinse skin thoroughly with water.
P/N-no.: M1203124 SDS-ID: US/8.0
FIRE-FIGHTING MEASURES
5.
Extinguishing media: Use fire-extinguishing media appropriate for surrounding materials.
Specific hazards: In case of fire, silica and oxide of carbon will be released.
ACCIDENTAL RELEASE MEASURES
6.
Personal precautions: For personal protection, see section 8.
Environmental precautions:
Avoid discharge into water courses or onto the ground.
Methods for cleaning up:
Dam and absorb spillage with sand, sawdust or other absorbent. For waste disposal, see section 13.
HANDLING AND STORAGE
7.
Safe handling advice: Avoid contact with eyes. Observe good chemical hygiene practices.
Technical measures: Work practice should minimize contact.
Technical precautions: Local exhaust is recommended.
Technical measures for safe storage:
No special precautions.
Storage conditions: Store in tightly closed original container. Store at room temperature.
EXPOSURE CONTROLS/PERSONAL PROTECTION
8.
Engineering measures: An eye wash bottle must be available at the work site.
Personal protection: Personal protection equipment should be chosen according to the the CEN standards and in collaboration with the supplier of the personal protective equipment.
Hand protection: Risk of contact: Wear protective gloves.
P/N-no.: M1203124 SDS-ID: US/8.0
PHYSICAL AND CHEMICAL PROPERTIES
9.
Viscous liquid, black or blue Appearance: slight odor Odor: not relevant pH: not available Boiling point: >150°C Flash point: not relevant Explosion limits: 1.1 Relative density: insoluble in water Solubility:
VOC (Volatile Organic Substances): 0 g/l Other data:
STABILITY AND REACTIVITY
10.
Stability: Stable under normal temperature conditions.
Conditions/ materials to avoid:
Temperatures above 200°C.
Hazardous
decomposition products:
Reacts with metals forming heat and hydrogen gas, which may form explosive vapor/air mixture. Silica dust and oxides of carbon are released at temperatures above 200°C.
TOXICOLOGICAL INFORMATION
11.
Inhalation: Not relevant at normal room temperatures. When heated, corrosive and toxic vapors may be formed.
Skin contact: Prolonged contact may cause redness and irritation.
Eye contact: Splashes may irritate.
Ingestion: No harmful effects expected in amounts likely to be ingested by accident.
Specific effects: None known. Carcinogenicity:
National Toxicology Program (NTP): No. I.A.R.C. Monographs: No.
P/N-no.: M1203124 SDS-ID: US/8.0
ECOLOGICAL INFORMATION
12.
Mobility: The product is insoluble in water and will sediment in water systems.
Degradability: The degradability of the product has not been stated.
Ecotoxicity: The product is not expected to be hazardous to the environment.
Bioaccumulative potential:
No data available on bioaccumulation.
Other adverse effects: None known.
DISPOSAL CONSIDERATIONS
13.
Dispose of waste and residues in accordance with local authority requirements.
Can be burned in a chemical incinerator equipped with an afterburner and scrubber. Cured product can be disposed of as non-hazardous waste.
Waste from residues: EWC-code: 16 05 09
TRANSPORT INFORMATION
14.
The product is not covered by international regulation on the transport of dangerous goods (IMDG, IATA, ADR/RID).
REGULATORY INFORMATION
15.
Labelling: Based on information from the manufacturer regarding the chemical composition, the product is not liable to classification and labelling.
TSCA: Listed. Specific provisions:
Europe/USA:
This Safety Data Sheet has been prepared according to the EU-regulation. National regulation:
-P/N-no.: M1203124 SDS-ID: US/8.0
OTHER INFORMATION
16.
The user must be instructed in the proper work procedure and be familiar with the contents of these instructions. Corrosion:
The compounds contain minimal levels of fluorine, chlorine, sulphur compounds and heavy metals, and are approved for use on stainless steel in nuclear plants. The materials are designed specifically to be compatible with stainless steels and other engineering alloys and not to compromise future corrosion behaviour should traces of replicas remain after replication.
Hydrogen embrittlement:
Free hydrogen atoms are not produced when the base and accelerator in RepliSet are mixed. Hydrogen embrittlement is not expected to occur.
Heat treatment:
The residual silicone film left by RepliSet replicas will not influence heat treatment processes. Silicone residues decompose at about 280ºC, mostly to silica dust and oxides of carbon, and the quantities involved are very small. The following sections contain revisions or new statements: 8.
The (*) indicates the changes made with respect to the previous version.
Approved by DHI.
The information on this data sheet represents our current data and is reliable provided that the product is used under the prescribed conditions and in accordance with the application specified on the packaging and/or in the technical guidance literature. Any other use of the product which involves using the product in combination with any other product or any other process is the responsibility of the user.
