Symantec NetBackup Appliance Getting Started Guide

(1)

Symantec NetBackup™

Appliance Getting Started

Guide

Release 2.0

(2)

Legal Notice

Symantec and the Symantec Logo, NetBackup, and Veritas are trademarks or registered trademarks of Symantec Corporation or its affiliates in the U.S. and other countries. Other names may be trademarks of their respective owners.

The product described in this document is distributed under licenses restricting its use, copying, distribution, and decompilation/reverse engineering. No part of this document may be reproduced in any form by any means without prior written authorization of Symantec Corporation and its licensors, if any.

THE DOCUMENTATION IS PROVIDED "AS IS" AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID. SYMANTEC CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING,

PERFORMANCE, OR USE OF THIS DOCUMENTATION. THE INFORMATION CONTAINED IN THIS DOCUMENTATION IS SUBJECT TO CHANGE WITHOUT NOTICE.

The Licensed Software and Documentation are deemed to be commercial computer software as defined in FAR 12.212 and subject to restricted rights as defined in FAR Section 52.227-19 "Commercial Computer Software - Restricted Rights" and DFARS 227.7202, "Rights in Commercial Computer Software or Commercial Computer Software Documentation", as applicable, and any successor regulations. Any use, modification, reproduction release, performance, display or disclosure of the Licensed Software and Documentation by the U.S. Government shall be solely in accordance with the terms of this Agreement.

Symantec Corporation 350 Ellis Street

Mountain View, CA 94043 http://www.symantec.com

(3)

Chapter 1 Introduction

... 5

About NetBackup appliance deployment ... 5

About NetBackup 5220 and Symantec Storage Shelf matched pairs ... 7

Chapter 2 Hardware installation

... 9

About mounting NetBackup appliance components ... 9

Connecting electrical and communications cables to NetBackup appliances ... 10

Chapter 3 Configuration

... 15

About appliance configuration guidelines ... 15

About the appliance initial configuration ... 17

About NetBackup appliance roles and modes ... 18

About appliance configuration sequence ... 19

Configuring a new appliance from the appliance interface ... 20

Configuring a new appliance from the appliance shell menu ... 31

About post appliance configuration tasks ... 37

Adding an appliance media server to an appliance master server ... 37

Adding a storage expansion unit to an appliance ... 38

Adding the appliance host name to the NetBackup master server ... 39

Installing NetBackup client software on clients used with appliances ... 40

About appliance and NetBackup documentation ... 41

(4)

(5)

Introduction

This chapter includes the following topics:

■ About NetBackup appliance deployment

■ About NetBackup 5220 and Symantec Storage Shelf matched pairs

About NetBackup appliance deployment

NetBackup appliance deployment consists of the complete installation and configuration of all appliance components to create a backup environment that is ready to use.

The Symantec NetBackup Getting Started Guide provides you with the information to get your appliance environment operational. Updates to this document were expected at the time of release. For the latest version of this document with the most recent updates, click on the following link:

http://www.symantec.com/docs/DOC2792

The following provides a brief description of the available appliance system components:

1

(6)

Table 1-1 Available appliance components Description

Component

NetBackup 5200:

■ 4U rackmount unit

■ Built-in disk storage

■ With NetBackup appliance Release 2.0, use as a master server or a media server.

NetBackup 5220:

■ Built-in disk storage

■ Use as a master server or a media server Servers

Symantec Storage Shelf:

■ Includes 16 disk drives

Note:The Symantec Storage Shelf is supported for use only with the NetBackup 5220.

Storage expansion unit

The following describes the supported NetBackup appliance configurations that you can deploy:

Table 1-2 Supported NetBackup appliance deployments Deployment description

System components

Single (standalone) NetBackup 5200 or NetBackup 5220 appliance with combined master server and media server functionality.

Master server

Single (standalone) NetBackup 5220 appliance with combined master server and media server functionality and a Symantec Storage Shelf.

Master server with storage expansion unit

A NetBackup 5200 or 5220 master server, and a 5200 or 5220 media server.

Master server and media servers

Same combinations as listed above, and one Symantec Storage Shelf can be connected to each NetBackup 5220. Master server, media servers,

storage expansion unit

NetBackup 5200 or 5220 media server for use with a traditional NetBackup master server.

For the deployments that use a NetBackup 5220, one Symantec Storage Shelf can be connected to the appliance. Media server only for a

non-appliance NetBackup system

(7)

The following describes the required tasks to deploy your NetBackup appliance environment:

Table 1-3 Appliance deployment tasks Description Task

Step

■ Mount all appliances in a 19-inch rack.

■ Mount the optional storage expansion unit in a 19-inch rack.

Install hardware 1

■ Connect a ground wire to the appliance (NetBackup 5200 only).

■ Connect the appliance to the corporate network.

■ Connect the optional storage expansion unit to the appropriate appliance.

■ Connect a laptop to the appliance (required for appliance configuration).

■ Connect power cords to the appliance and to the optional storage expansion unit.

■ Turn on the optional storage expansion unit.

Note:For the systems that include a Symantec Storage Shelf, this unit must be turned on first and allowed to boot up completely.

■ Turn on the appliances. Connect cables

and turn on units 2

■ Configure all appliances.

■ Add the storage expansion unit to the appropriate appliance.

Configure 3

About NetBackup 5220 and Symantec Storage Shelf

matched pairs

When you order a NetBackup 5220 and a Symantec Storage Shelf together, these units are initialized together at the factory to create a matched pair. Matched pairs provide optimum performance and they should always be used together to help ensure successful installation and configuration.

To help you identify matched pairs, check the labels on the back of each Symantec Storage Shelf. Each unit has two labels that identify the serial numbers of the matched pair.

7 Introduction About NetBackup 5220 and Symantec Storage Shelf matched pairs

(8)

(9)

Hardware installation

■ About mounting NetBackup appliance components

■ Connecting electrical and communications cables to NetBackup appliances

About mounting NetBackup appliance components

Each appliance system component includes guide rails and fasteners for installation in a 19-inch rack.

The following describes the guide rail styles that are included with each system component:

Table 2-1 Guide rails styles for NetBackup appliance systems Guide rail style

Component Screw mount NetBackup 5200 (4U) Snap-in mount NetBackup 5220 (2U) Screw mount Symantec Storage Shelf (3U)

Note:Mounting methods vary by rack manufacturer. Racks may contain mounting rails with square holes, round holes, or round threaded holes. You may need to acquire other mounting hardware to install the guide rails in your rack.

2

(10)

Connecting electrical and communications cables to

NetBackup appliances

After all appliance hardware installation is completed, you are ready to make all the necessary cable connections.

Use the following procedure to connect electrical and communications cables from the appliance to the appropriate sources.

To connect electrical and communications cables from the appliance to the appropriate sources

1

For 5200 appliances, connect a ground wire from the appliance ground screw to a true earth ground.

2

For 5200 appliances, connect your corporate network to the following appliance ports:

Additional Ethernet ports (10GB) NIC3 (eth2) and higher

AC power jacks Power switch

1GB Ethernet ports NIC2 (eth1) Corporate network connection NIC1 (eth0) Laptop connection

Note:The number of expansion card ports (NIC3/eth2 and higher) varies depending on the hardware configuration that was ordered.

(11)

3

For 5220 appliances, connect your corporate network to the following appliance ports:

F

1GB Ethernet ports

Additional Ethernet ports (1GB or 10GB) NIC3 (eth2) and higher

AC power jacks NIC1 (eth0) Laptop connection NIC2 (eth1) Corporate network connection

Note:The number of expansion card ports (NIC3/eth2 and higher) varies depending on the hardware configuration that was ordered.

4

Connect a standard Ethernet cable from a laptop computer to appliance port NIC1.

11 Hardware installation Connecting electrical and communications cables to NetBackup appliances

(12)

5

If your system includes a storage expansion unit, connect two SAS cables to the SAS In ports on the unit.

Note:For optimum performance, make sure that you connect the storage expansion unit to the appliance that it is matched with from the factory. To help you identify matched pairs, check the labels on the back of each Symantec Storage Shelf. Each unit has two labels that identify the serial numbers of the matched pair.

SAS In ports AC power jacks Power switches SAS In SAS In SAS Out SAS Out

Connect the other ends of the SAS cables to the available expansion card ports on the NetBackup 5220 appliance.

Warning:Once these connections are made, the storage expansion unit becomes an electrically integral part of the appliance. Any disconnection of these cables requires that you contact Symantec Technical Support.

6

Connect both power cables to the appliance, then plug in the other ends to the AC power source.

For systems with a storage expansion unit, connect the appropriate power cables to the unit and plug the other ends into the AC power source.

7

This step describes the sequence to turn on all units. If your system includes a storage expansion unit, the sequence for turning on the equipment is critical to ensure correct communication.

The following describes the order in which to turn on the units in configurations with or without storage expansion units:

■ For the systems that consist only of appliance servers, turn on all appliances. The sequence is not critical.

(13)

■ For the systems that include storage expansion units:

■ Turn on all storage expansion units and wait for each unit to boot up completely.

When all of the lights on the units stop blinking and are on steady, the boot up is complete.

■ Turn on all appliances.

The power switches on the 5200 server and the storage expansion unit are located on the rear panel.

The power switch on the 5220 server is located on the front panel.

8

Turn on the laptop computer.

The appliance is now ready for configuration.

See“About appliance configuration guidelines”on page 15.

13 Hardware installation Connecting electrical and communications cables to NetBackup appliances

(14)

(15)

Configuration

■ About appliance configuration guidelines

■ About the appliance initial configuration

■ About appliance configuration sequence

■ Configuring a new appliance from the appliance interface

■ Configuring a new appliance from the appliance shell menu

■ About post appliance configuration tasks

■ About appliance and NetBackup documentation

About appliance configuration guidelines

Use the following configuration guidelines when you deploy new appliances:

3

(16)

Table 3-1 Appliance configuration guidelines Description

Parameter

Before you start the configuration, make sure that you have the following information:

■ Network IP addresses, netmask, and gateway IP addresses for the appliance.

■ Network names for all appliances

■ DNS or host information

If DNS is used, make sure that the network names of all appliances and the master server are DNS resolvable (FQHN and short name). If DNS is not used, make sure that you enter the proper host entries for the appliance that you are configuring.

■ Password for appliance access

The default password for appliance access is P@ssw0rd.

■ Names for disk storage units

The Storage Name fields appear only when you configure the appliance as a media server For use with a traditional NetBackup

master server. You can change the default names or leave them.

Required names and addresses

Make sure that the following ports are open on any firewall that exists between a master server and a media server:

■ 13724 (vnetd)

■ 13720 (bprd)

■ 1556 (PBX) Firewall port

usage

NetBackup appliances include one-year temporary license keys for the NetBackup Deduplication and the AdvancedDisk storage options. The keys are added to the master server automatically during the initial appliance configuration.

You must replace these keys with permanent keys before they expire. Disk storage

option licenses

NetBackup appliance Release 2.0 includes NetBackup version 7.1. To use an appliance media server with a traditional NetBackup master server, the master server must also use NetBackup version 7.1 or later. If the NetBackup master server currently uses NetBackup version 7.0 or earlier, it must first be upgraded to version 7.1 before you configure the appliance.

For all configurations, the master server must always use the same or a later version of NetBackup than the NetBackup version used on media servers.

NetBackup version compatibility

(17)

About the appliance initial configuration

After you log in to the appliance from the laptop, a series of pages guide you through the initial configuration. The first page presents an overview of the appliance setup to inform you about the information that you must provide to complete the configuration.

You can click Help on any initial configuration page if you need more information about what you need to provide in the data entry fields.

The following describes the information on the initial configuration pages. Table 3-2 Initial configuration page

Description Page title

Shows the order of configuration and a brief summary of the pages that follow.

Overview of appliance setup

Provides the following data entry fields for the appliance network setup: ■ IP Address ■ Subnet Mask ■ NIC ■ Bond Mode ■ Destination IP

■ Destination Subnet Mask

■ Default Gateway Network

Configuration

Provides the following data entry fields for the appliance host name setup:

■ Host Name

■ DNS Name Server(s) IP Address

■ Domain Name Suffix

■ Search Domain(s)

■ Host Name Resolution

IP Address, Fully-Qualified-Hostname, and Short-Hostname. Host and Sytem

Configuration

Provides the following choices and the data entry fields for the appliance time zone and date setup:

■ NTP

Server IP Address

■ None

Date and Time

■ Time Zone TimeZone and Date Configuration 17 Configuration About the appliance initial configuration

(18)

Table 3-2 Initial configuration page (continued) Description

Page title

Provides the following data entry fields for the appliance password setup:

■ Old Admin Password

■ New Admin Password

■ Confirm New Admin Password Security

Provides the following choices and the data entry fields for the appliance role setup and the disk configuration:

■ Master Server

■ Media Server

For use with a traditional NetBackup master server

The NetBackup master server must have NetBackup version 7.1 or later installed.

For use with an appliance master server

■ Enter the fully qualified host name of master server

Required only when you select a media server role.

■ AdvancedDisk volume (See note.)

■ Storage Unit Name (See note.)

Note:The AdvancedDisk volume and the Storage Name fields appear only when you select the media server role For use with a traditional

NetBackup master server. Appliance Role

About NetBackup appliance roles and modes

When you configure your appliance for the first time, you must select a role and a mode for the appliance. The role refers to the server type and the mode refers to the interface that is used for system administration.

The following describes the available roles and the associated modes: Table 3-3 Appliance role and mode descriptions

Mode—user interface Role—server type

Select this role to configure the appliance as a master server. This role provides the traditional NetBackup interfaces to back up and restore applications and file systems.

(19)

Table 3-3 Appliance role and mode descriptions (continued) Mode—user interface

Role—server type

Choose one of the following modes:

■ For use with a traditional NetBackup master server

The NetBackup master server must have NetBackup version 7.1 or later installed.

Before configuration, you must add this appliance host name to the Additional Servers list on the NetBackup master server.

■ For use with an appliance master server

After configuration, you must add this appliance to the appliance master server.

Media Server

About appliance configuration sequence

If your system includes more than one appliance or a storage expansion unit, configuration must be done in a specific order.

The following describes the proper sequence for appliance configuration, based on the system components.

Table 3-4 Appliance configuration order Configuration order System

Configure the appliance as a master server.

See“Configuring a new appliance from the appliance interface”on page 20.

See“Configuring a new appliance from the appliance shell menu”on page 31.

Single appliance system (standalone)

■ Configure the first appliance as a master server.

■ Configure the remaining appliances as media servers for use with an appliance master server.

Multiple appliance system (master server and media servers)

19 Configuration About appliance configuration sequence

(20)

Table 3-4 Appliance configuration order (continued) Configuration order

System

Configure the appliance as a media server (For use with an

appliance master server) and add it to the appliance master

server.

See“Adding an appliance media server to an appliance master server”on page 37.

Appliance media server (for use with an existing appliance master server)

Before you configure this type of media server, you must first update the NetBackup master server with the appliance host name.

Perform the following tasks in the order as shown:

■ Add the appliance name to the Additional Servers list on the NetBackup master server.

See“Adding the appliance host name to the NetBackup master server”on page 39.

■ Configure the appliance as a media server (For use with

a traditional NetBackup master server).

Appliance media server (for use with an existing traditional NetBackup master server)

After all appliances have been configured, add the storage expansion unit to the server on which it is physically connected.

See“Adding a storage expansion unit to an appliance” on page 38.

Systems that include a storage expansion unit

Configuring a new appliance from the appliance

interface

The following procedure describes how to configure a new appliance by using the appliance user interface.

(21)

To configure a new appliance from the appliance user interface

1

On the laptop that is connected to the NIC1 appliance port, navigate to the

Local Area Connection Properties dialog box.

On the General tab, select Internet Protocol (TCP/IP) so that it is highlighted, then click Properties.

On the Alternate Configuration tab, perform the following tasks:

21 Configuration Configuring a new appliance from the appliance interface

(22)

■ Click User Configured.

■ For the IP address, enter 192.168.1.nnn, where nnn is any number from 2 through 254.

■ For the Subnet mask, enter 255.255.255.0.

■ Click OK.

2

On the laptop that is connected to the appliance, open a Web browser to the following URL:

http://192.168.1.1

Make sure that you affirm the security exception to proceed.

3

Log on to the appliance as follows:

■ For User Name, enter admin.

■ For Password, enter P@ssw0rd.

4

To start the configuration, click Setup Appliance.

(23)

When you add entries to the Configure Network fields, those values are configured on the appliance after you click Add. The configuration entries then appear automatically in the read-only fields of the Applied Network Configuration table. The following describes the Configure Network fields.

■ IP Address

Enter the IPv4 address to be used for this appliance. You can also enter a new IP address of an appliance that you want to configure.

■ Subnet Mask

Enter the subnet value that corresponds to the IP address.

■ NIC

This field displays the network device name that you can choose when you add a new network to the configuration. Use the following guidelines to bond NICs:

■ The NIC drop-down list shows the supported combination of appliance Ethernet ports that can be bonded. The list is compiled automatically and is based on the link types and the link speeds of the ports. Ports do not require connection to the network to appear in the list.

■ Select Auto to have the NICs selected automatically. This mode selects the best possible set of NICs to plumb the IP address on. The selection is based on the available NICs, the link type (copper or FC), and the link speed. If multiple NICs have the same properties, then a bond (link aggregation) is created and the IP address is plumbed on the bond.

■ Only NICs of the same type and speed can be bonded.

■ Once a NIC is bonded, it cannot be bonded to another NIC. To reassign a bond, you must first remove the NIC from its current bond.

Configure Network

(24)

■ Bond Mode

This field lets you combine (aggregate) multiple network interfaces into a single logical "bonded" interface. The behavior of the bonded interfaces depends upon the mode. The default bond mode is balance-alb.

The available bonding modes are as follows:

■ balance-rr ■ active-backup ■ balance-xor ■ broadcast ■ 802.3ad ■ balance-tlb ■ balance-alb

Some bond modes require additional configuration on the switch or the router. You should take additional care when you select a bond mode.

For more information about bond modes, see the following documentation:

http://www.kernel.org/doc/Documentation/networking/bonding.txt After you enter all of the necessary information in the Configure

Network fields, you must click Add. The information that you

entered appears in the Applied Network Configuration table for confirmation.

(25)

Enter the kernel routing configuration of the appliance as follows:

■ Destination IP

Enter the network IP address of a destination network. For the initial appliance configuration, this field contains a default value that cannot be changed. When you configure another destination IP, you must enter the appropriate address.

■ Destination Subnet Mask

Enter the subnet value that corresponds to the IP address. For the initial appliance configuration, this field contains a default value that cannot be changed. When you configure another route, you must enter the appropriate value.

■ Default Gateway

Enter the address of the network point that acts as an entrance to another network.

■ NIC

The appliance can use multiple network interface cards (NICs). This column displays the network device name.

Refer to the Linux route command for more information about how to add routing entries.

After you enter all of the necessary information in these fields, you must click Add. The information that you entered appears in the Applied Routing Configuration table for confirmation.

ConfigureRouting

6

Click Next.

7

On the Host and System Configuration page, enter the following information:

Host Name

Enter the fully qualified host name (FQHN) of the appliance name.

Note:For media servers to be used with a traditional NetBackup master server, make sure that you have already added the appliance name to the Additional Servers list on the NetBackup master server. That ensures that the appliance host name is resolvable from the master server.

(26)

■ DNS Name Server(s) IP Address

Enter the IP address of the DNS server.

To enter multiple DNS IP addresses, use a comma character as the delimiter between each address and no spaces.

■ Domain Name Suffix

Enter the suffix name of the DNS server.

■ Search Domain(s)

You can enter one or more DNS search domain names to search when an unqualified host name is given. To enter multiple search domain names, use a comma character as the delimiter between each name and no spaces.

■ Host Name Resolution

■ IP Address

Enter the IP address of the appliance.

■ Fully-Qualified-Hostname

Enter the fully qualified domain name (FQHN) of the appliance.

■ Short-Hostname

Enter the short name of the appliance.

After you enter all of the necessary information in these fields, you must click Add. The Host Name Resolution information that you entered appears below these data entry fields for confirmation.

DNS and Host Name Resolution

(27)

9

On the TimeZone and Date Configuration page, enter the following information:

Server IP Address

To use NTP (Network Time Protocol) to set the time and the date of the appliance, enter the IP address of the NTP server.

NTP

Date and Time

To set the date and the time of the appliance without NTP, click

None and enter the appropriate date and time.

Enter the date manually by using the mm/dd/yyyy format, or click on the calendar icon and select the date.

Enter the time by using the hh:mm:ss format. Entries must be in the 24-hour format (00:00:00 - 23:59:59)

None

Whether you select to use NTP or None, you must set the time zone.

To set the time zone for the appliance, click on the Time Zone drop-down box and select the appropriate time zone.

Time Zone

10

Click Next.

11

On the Security Configuration page, enter the following information:

Note:You are not required to change the default administrator's password. For increased security, Symantec recommends that you change the password periodically and keep a record of the current password in a secure location.

For the initial configuration, the default password isP@ssw0rd.

Old Admin Password

(28)

Enter the new password.

The password must be seven or more characters long. A seven character password must include all of the following requirements, while a longer password must include at least three of the following requirements:

■ One uppercase letter

■ One lowercase letter

■ One number (0-9)

■ One special character (for example, !, @, #, etc.) A password that begins with an uppercase letter and ends with a number is unacceptable, unless you include another uppercase letter and another number between them.

New Admin Password

Enter the new password again for confirmation.

Confirm New Admin Password

12

Click Next.

(29)

Choose the role and the mode for the appliance as follows:

Select this role to configure the appliance as a master server.

Select this role to configure the appliance as a media server, then choose one of the following modes:

■ For use with a traditional NetBackup master server

Before configuration, you must first add this appliance to the Additional Servers list on the NetBackup master server.

See“Adding the appliance host name to the NetBackup master server”on page 39.

■ For use with an appliance master server

After configuration, you must add this appliance to the appliance master server.

See“Adding an appliance media server to an appliance master server”on page 37.

■ Enter the fully qualified host name of the master server

Enter the FQHN of the master server.

If you selected For use with a traditional NetBackup

master server and the NetBackup server is in a cluster,

you must enter all of the clustered master server names. When you enter multiple names, the cluster name must be entered first. Then enter the remaining master server names and separate each name with a comma and no space.

Role

Configuration

(30)

Note:The Disk Configuration fields appear only when you configure an appliance as a media server and select For use with

a traditional NetBackup master server.

You can configure appliance disk unit storage as NetBackup Deduplication, AdvancedDisk, or a combination of both. By default, the entire disk is allocated for NetBackup Deduplication.

Note:The appliance includes one-year temporary license keys for the NetBackup Deduplication and the AdvancedDisk storage options. You must replace these temporary keys on the master server before they expire, with permanent keys.

To resize disk storage units, enter the size or the percentage of storage that you want to allocate for the AdvancedDisk disk volume. The remaining storage is calculated and assigned automatically to the NetBackup Deduplication volume. When both are added together, the new storage values for both disk volumes are displayed as the Total Appliance Disk Group. To resize the disk storage volumes and rename storage units, do the following:

■ AdvancedDisk volume

Enter the appropriate number in the Size (GB) field or the

Percentage (%) field.

The remaining disk space is allocated automatically to the NetBackup Deduplication volume.

■ Storage Unit Name

You can leave the default names or you may change them. To change the default names, enter the appropriate name for each storage unit.

Disk

Configuration

14

To review your configuration selections, click Next. A pop-up window appears and asks you to verify that your Appliance role configuration selection is correct. You can do one of the following:

■ If you do not want to change any items, click OK. The summary page appears.

■ If you want to change any items, click Cancel. The Role Configuration page is still active and you can make changes to your configuration. Click

Next. The confirmation pop-up window appears for you to verify your

configuration selections. Click OK. The summary page appears.

15

After configuration has completed, wait about 10 minutes for the NetBackup services to start. You must then use the fully qualified host name to reconnect to the appliance.

(31)

16

Repeat this procedure to configure all other new or unconfigured appliances.

17

After all appliances have been configured, proceed to the following topic: See“About post appliance configuration tasks”on page 37.

Configuring a new appliance from the appliance shell

1

On the laptop that is connected to the NIC1 appliance port, navigate to the

Local Area Connection Properties dialog box.

On the General tab, select Internet Protocol (TCP/IP) so that it is highlighted, then click Properties.

On the Alternate Configuration tab, perform the following tasks:

31 Configuration Configuring a new appliance from the appliance shell menu

(32)

■ Click User Configured.

■ For the IP address, enter 192.168.1.nnn, where nnn is any number from 2 through 254.

■ For the Subnet mask, enter 255.255.255.0.

■ Click OK.

2

On the laptop that is connected to the appliance, open an SSH session to 192.168.1.1 and log on to your appliance.

The logon isadminand the default password isP@ssw0rd.

After you log on, the welcome message appears in the shell menu and the prompt is at the Main_Menu view.

(33)

3

From the Main_Menu > Network view, enter the following command to configure the IP address of a single network that you want your appliance to connect to.

Configure IPAddress Netmask GatewayIPAddress [InterfaceNames]

Where IPAddress is the new IP address, Netmask is the netmask, and

GatewayIPAddress is the default gateway for the interface. The

[InterfaceNames]option is optional.

If you want to configure multiple networks you must first configure the IP address of each network that you want to add. Then you configure the Gateway address for each network you added. You must make sure that you add the default Gateway address first. Use the following two commands.

IPv4 IPAddress Netmask [InterfaceName]

Where IPAddress is the new IP address, Netmask is the netmask, and

[InterfaceName]is optional. Repeat this command for each IP address that

you want to add.

Gateway Add GatewayIPAddress [TargetNetworkIPAddress] [Netmask] [InterfaceName]

Where GatewayIPAddress is the gateway for the interface and

TargetNetworkIPAddress, Netmask, andInterfaceNameare optional. Repeat

this command to add the gateway to all of the destination networks. If you do not use DNS, then you can proceed to Step 7.

4

From the Main_Menu > Network view, use the following command to set the appliance DNS domain name.

DNS Domain Name

Where Name is the new domain name for the appliance.

5

From the Main_Menu > Network view, use the following command to add the DNS name sever to your appliance configuration.

DNS Add NameServer IPAddress

Where IPAddress is the IP address of the DNS server.

To add multiple IP addresses, use a comma to separate each address and no space.

(34)

6

From the Main_Menu > Network view, use the following command to add a DNS search domain to your appliance configuration so the appliance can resolve the host names that are in different domains:

DNS Add SearchDomain SearchDomain

Where SearchDomain is the target domain to add for searching.

7

This step is optional. It lets you add the IP addresses of other hosts in the appliance hosts file.

From the Main_Menu > Network view, use the following command to add host entries to the hosts file on your appliance.

Hosts Add IPAddress FQHN ShortName

Where IPAddress is the IPv4 address, FQHN is the fully qualified host name, and ShortName is the short host name.

8

From the Main_Menu > Network view, use the following command to set the host name for your appliance.

Hostname Set Name

Where Name is the fully qualified host name.

With this step, NetBackup is re-configured to operate with the new host name. This process may take a while to complete.

9

Select the role for the appliance and run the appropriate configuration commands as follows:

From the Main_Menu > Appliance view, run the following command:

Master

For use with an appliance master server

For this role, there is no command to enter. The initial configuration is complete.

The next task you must complete is to add the name of this media server to the configured appliance master server.

See“Adding an appliance media server to an appliance master server”

on page 37.

For use with a traditonal NetBackup master server

From the Main_Menu > Appliance view, run the following command:

(35)

Where MasterServer is either a stand-alone master server, a Multihomed master server, or a clustered master server.

The following defines each of these scenarios:

■ Stand-alone master server

This scenario shows one master server host name. This name does not need to be a fully qualified name as long as your appliance recognizes the master server on your network. The following is an example of how the command would appear.

Media MasterServerName

■ Multihomed master server

In this scenario, the master server has more than one host name that is associated with it. You must use a comma as a delimiter between the host names. The following is an example of how the command would appear.

Media MasterNet1Name,MasterNet2Name

■ Clustered master server

In this scenario, the master server is in a cluster. Symantec

recommends that you list the cluster name first, followed by the active node, and then the passive nodes in the cluster. This list requires you to separate the node names with a comma. The following is an example of how the command would appear.

Media MasterClusterName,ActiveNodeName,PassiveNodeName

■ Multihomed clustered master server

In this scenario, the master server is in a cluster and has more than one host name that is associated with it. Symantec recommends that you list the cluster name first, followed by the active node, and then the passive nodes in the cluster. This list requires you to separate the node names with a comma. The following is an example of how the command would appear.

Media MasterClusterName,ActiveNodeName, PassiveNodeName,MasterNet1Name,MasterNet2Name

To prevent any future issues, when you perform the appliance role configuration, Symantec recommends that you provide all of the associated master server names.

Note:The following steps for disk configuration apply only for the appliances that are configured for the media server role For use with a traditional

NetBackup master server.

(36)

10

If you selected the media server role For use with a traditional NetBackup

master server, the available storage and the current storage configuration

information appears. This information looks similar to the following: the storage pool is configured and the following prompt appears:

Available Storage = xGB

Current Storage Pool Configuration:

Deduplication Storage = xGB (100%), AdvancedDisk = 0GB (0%)

11

The configuration process asks you if you want to configure your storage as AdvancedDisk.

Do you want part of your storage configured as AdvancedDisk? (yes/no): y

Enter y to configure an AdvancedDisk volume.

12

You are then asked to enter the size of AdvancedDisk Volume.

Enter Size of AdvancedDisk Volume (use a % sign if you want it as a percent of the total, or input size is GBs): 0%

Enter a percentage of the total storage, or a value that is measured in Gigabytes (GB).

13

Enter y to confirm the size you entered. Enter n if you want to change the value.

14

You are then prompted to enter an AdvancedDisk storage unit name if the AdvancedDisk volume size is greater than zero. In addition, you are prompted to enter a Deduplication storage unit name if the Deduplication volume size is greater than zero. You are not required to change the default names. Enter a name for the AdvancedDisk pool. For example,stu_adv_disk_name. Enter a name for the Deduplication disk pool. For example,stu_disk_name

A confirmation message appears that states the storage unit pools have been successfully created.

You can view information about your appliance by reviewing the NetBackup appliance log files.

(37)

Note:Before or immediately after initial configuration, Symantec recommends that you change the default maintenance password (P@ssw0rd) for your appliance. This password must be provided to technical support in case you need future troubleshooting assistance. You must change the maintenance password through the command-line interface with the following command:Main > Support > Maintenance. For complete information, see the NetBackup 5200 Series Appliance

Administrator's Guide.

About post appliance configuration tasks

If your appliance system includes media servers or a Symantec Storage Shelf, you must add these components to the appropriate configured server. You also need to install NetBackup client software on the computers that you want to back up. The following describes the necessary post appliance configuration tasks. The tasks appear in the order in which they must be performed.

Table 3-5 Post appliance configuration tasks Description

Task

After all appliances have been configured, appliance media servers must be added to the appropriate appliance master server.

See“Adding an appliance media server to an appliance master server” on page 37.

Add appliance media servers to the appliance master server

If your system includes storage expansion units, they must be added to the appropriate appliance.

See“Adding a storage expansion unit to an appliance”on page 38. Add the storage

expansion unit to the appliance

After all appliances and storage expansion units are operational, you are ready to install client software on the computers that you want to back up.

See“Installing NetBackup client software on clients used with appliances”on page 40.

Note:The client installation instructions are also included in the Symantec NetBackup 5200 Series Appliance Administrator's Guide. Install client

software

Adding an appliance media server to an appliance master server

After you configure an appliance media server, you must add it to the configured appliance master server.

37 Configuration About post appliance configuration tasks

(38)

Use the following procedure to add a configured appliance media server to a configured appliance master server.

To add a configured appliance media server to a configured appliance master server

1

Log in to the appliance master server as the administrator.

To perform the task from the appliance shell menu, open an SSH session to the appliance master server and log in as the administrator.

2

Use one of the following methods to add the appliance media server:

Appliance shell menu method Appliance interface method

From the Main_Menu > Appliance view, run the following command:

Add ApplianceName AdminPassword

Where ApplianceName is the fully qualified host name (FQHN) or the short name of the appliance media server and AdminPassword is the admin password for that same appliance.

■ Click Manage > Appliance > Add

Appliance.

■ In the Appliance Hostname field, enter the fully qualified host name (FQHN) or the short name of the appliance media server that you want to add.

■ In the Admin Password field, enter the admin password of the appliance media server that you want to add.

■ Click Add.

Adding a storage expansion unit to an appliance

After you have completed the appliance configuration, you must add any connected Symantec Storage Shelf to the appliance through the appliance shell interface. Use the following procedure to add a storage expansion unit to the appliance. To add a storage expansion unit to the appliance

1

Log in to the configured appliance through an SSH connection.

2

To view all available disks, enter the following command:

Manage > Storage > List

The screen shows the available enclosures (storage expansion units) that can be added to the NetBackup storage disk pool. The enclosure or the storage expansion unit is identified as NEW AVAILABLE.

(39)

3

To expand the NetBackup disk storage pool to include the storage expansion unit, enter the following command:

Manage > Storage > Expand

Warning:Do not disconnect or power cycle the storage expansion unit during this process.

4

Please confirm all of the messages as they appear.

The new total size of the NetBackup storage disk pool appears with the following message:

Expansion of NetBackup Storage Expansion Pool passed

Adding the appliance host name to the NetBackup master server

To use a NetBackup appliance as a media server with a traditional NetBackup master server, you must first update the NetBackup master server. The appliance host name must be added to the Additional Servers list on the NetBackup master server.

Use the following procedure to add the appliance host name to the NetBackup master server.

To add the appliance host name to the NetBackup master server

1

On the master server, log on to the NetBackup Administration Console as the administrator.

2

On the main console window, in the left pane, click NetBackup Management

> Host Properties > Master Servers.

3

In the right pane, click on the master server host name.

4

On the Host Properties window, in the left pane, click Servers.

5

In the right pane, in the Additional Servers section, click Add and enter your appliance host name. The appliance host name should appear in the top

Additional Servers section.

If the appliance has more than one host name, you must add all of the names to the additional server sections on the master server.

6

Click OK and close the Master Server Properties window.

After you complete this procedure, the appliance is ready to be configured as a media server for use with a traditional NetBackup master server. See“Configuring a new appliance from the appliance interface”on page 20.

39 Configuration About post appliance configuration tasks

(40)

Installing NetBackup client software on clients used with appliances

After all appliance configuration has been completed, you are ready to install client software on the clients that you want to back up. You must also add the appliance master server name to the client.

The following procedures describe how to install Windows and UNIX client software on the clients that are used with NetBackup appliances.

Note:If you have existing NetBackup clients that you want to use with the appliance master server, they must be version 6.0 or later. For these clients, you only need to add the appliance master server name to the client.

To install the NetBackup client software on a Windows client

1

On the Windows client computer where you want to install the NetBackup client software, log on as the administrator.

2

Open a Map or a directory to the following CIFS shared folder on the appliance:

\\<appliance_name>\install

3

Click on the Windows executable, quickinstall.exe. This action installs the NetBackup client software.

4

Add the appliance master server name to the Windows Registry on the client as follows:

■ On the client, click Start > Run....

■ In the dialog box that appears, enter regedit and click OK.

■ In the Registery Editor window that appears, in the left pane, navigate to the following location:

Veritas > NetBackup > CurrentVersion > Config

■ In the right pane which shows the contents of the Config directory, click twice on the Server file.

■ In the dialog box that appears, enter the fully qualified host name of the appliance master server and click OK.

(41)

To install the NetBackup client software on a UNIX client

1

On the UNIX client computer where you want to install the NetBackup client software, log on as root.

2

Mount the following NFS share:

<appliance_name>:/inst/client

3

Browse the files within the NFS share directory. Files that are similar to the following appear: quickinstall.exe clientconfig .packages unix-client-install docs PC_Clnt

4

Run theunix-client-installscript.

This action installs the NetBackup client software.

5

Add the appliance master server name to thebp.conffile on the client as

follows:

■ On the client, navigate to the following location:

cd /usr/openv/netbackup

■ Enterlsto see the contents of the directory.

■ Open thebp.conffile in a text editor.

■ Enter the fully qualified host name of the appliance master server.

■ Save your changes and close the file.

About appliance and NetBackup documentation

After all appliance configuration and client software installation have been completed, you are ready to use your NetBackup appliance system.

The following describes the documentation that you should reference for system management:

■ All traditional NetBackup documentation (excluding installation guides) All NetBackup documentation can be found on the Symantec Support at the following location:

http://www.symantec.com/docs/TECH154178

■ NetBackup 5200 Series Appliance Administrator's Guide

■ NetBackup 5200 Series Appliance Release Notes

41 Configuration About appliance and NetBackup documentation

(42)

■ NetBackup 5200 Series Appliance Troubleshooting Guide Technote

■ NetBackup 5200 Administrator's Guide

■ NetBackup 5200 Troubleshooting Guide Technote

All NetBackup 5200 and 5220 documentation can be found at the following location: