Solidworks Tutorial For Beginner
104
0
0
Full text
(2) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Foreword The main objective of these tutorials is to give you a kick start using SolidWorks. The approach to write this tutorial is based on what is the most important knowledge you should know and what is commonly tool used. You will learn step by step by working on it. These tutorials will teach you the basic skills of using Solidworks in your daily design works. Even this tutorials didn’t have full explanations of tools that Solidworks have but don’t worry you will master it along the way, as I did. If you have any questions about these tutorials, drop your mail to [email protected]. Solidworks 2010 Tutorials: Beginner http://www.solidworkstutorials.com ©2010 solidworkstutorials.com , All rights reserved. This publication is copyright under the solidworkstutorials.com All rights reserved. Apart from any fair dealing for the purpose of private study, research, criticism, or review, as permitted under the Copyright Designs and Patents Act 1988, no part may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, electrical, chemical, mechanical, photocopying, recording or otherwise, without the prior permission of the copyright owners. Unlicensed multiple copying of this publication is illegal. Inquiries should be addressed to: [email protected] If this guide is distributed with software that includes an end-user agreement, this guide, as well as the software described in it, is furnished under license and may be used or copied only in accordance with the terms of such license. Except as permitted by any such license, no part of this guide may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of solidworkstutorials.com. Please note that the content in this guide is protected under copyright law even if it is not distributed with software that includes an end-user license agreement. The content of this guide is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by solidworkstutorials.com. Solidworkstutorials.com assumes no responsibility or liability for any errors or inaccuracies that may appear in the informational content contained in this guide. Please remember that existing artwork or images that you may want to include in your project may be protected under copyright law. The unauthorized incorporation of such material into your new work could be a violation of the rights of the copyright owner. Please be sure to obtain any permission required from the copyright owner. Any references to company names in sample templates are for demonstration purposes only and are not intended to refer to any actual organization. The publishers are not responsible for any statement made in this publication. Data, discussion, and conclusions developed by the Author are for information only and are not intended for use without independent substantiating investigation on the part of the potential users. Opinions expressed are those of the Author and are not necessarily those of the Institution of Mechanical Engineers or its publishers.. i.
(3) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Solidworks Tutorials: Beginner Table of contents. www.solidworkstutorials.com. Table of contents Beginner Part 1: My First Solid … … … … 1 The big picture how SolidWorks works, it starts with a simple editable sketch. From this sketch a feature build the solid. From this solid it produces drawing... Beginner Part 2: Sketching … … … Sketch is the base of your part, it’s a good practice to master sketching in SolidWorks.... … 10. Beginner Part 3: Turning Parts … … … … 23 Some parts such as pins and shafts can be manufacture by turning process on lathe machine, we can create turning part by revolving it sketch on it axis... Beginner Part 4: Hole Wizard … … … … 30 Hole Wizard is used for creating predefined and standard holes such as counter bore hole, counter sunk hole, screw clearance hole and many more... Beginner Part 5: Pattern … … … … 40 Pattern (or some called array) is used to repeat features in linear arrangement or circular arrangement. It’s good to know how to optimize these tool, it help you make your part faster and easier... Beginner Part 6: Assembly Parts … … … 60 Assembly is a part of design process, it show how all designed parts work together as a single unit... Beginner Part 7: Detailing Drawing … … … 80 Once solid parts created we need to transfer it to engineering drawing so the others can understand your parts…. Solidworks Tutorials: Beginner Table of contents. ii.
(4) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 1: My First Solid. www.solidworkstutorials.com. Beginner Part 1: My First Solid The big picture how SolidWorks works, it starts with a simple editable sketch. From this sketch a feature build the solid. From this solid it produces drawing... Let’s begin your first solid.... 1.. Click New. 2.. Click Front Plane, insert sketch on plane by click Sketch.. In this tutorial you will make this 3. bracket, start from sketch and build features.. 4.. Beginner Part 1: My First Solid. Click Sketch. , click Part. , OK.. , click. Corner Rectangular . Start first point at origin and click another point at top right side.. Click Smart Dimension , click top edge set dimension to 3in and click right edge set dimension to 2in.. 1.
(5) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 1: My First Solid. www.solidworkstutorials.com. 5.. Beginner Part 1: My First Solid. To build features, click Extruded Boss/Base. , set D1 to. 0.10in. .. and. 2.
(6) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 1: My First Solid. www.solidworkstutorials.com 6.. Click on front face of the part, click Normal To.. 7.. Click Circle. , sketch circle on face. .. Click Smart Dimension , click circle edge and set diameter to 0.6in. For circle positioning click circle edge and vertical part edge set to 0.5in. Click circle edge again and click horizontal part edge set to 0.5in.. Beginner Part 1: My First Solid. 3.
(7) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 1: My First Solid. www.solidworkstutorials.com. 8.. Click Extruded Cut. All. Beginner Part 1: My First Solid. , change Direction 1 to Through. and. .. 4.
(8) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 1: My First Solid. www.solidworkstutorials.com 9.. Click on front face and select Sketch. . Select Corner Rectangular top right edge to center.. 10. Click Smart Dimension dimension to 2in and 1in.. Beginner Part 1: My First Solid. sketch rectangular from. , set rectangular. 5.
(9) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 1: My First Solid. www.solidworkstutorials.com. Click Extruded Cut. and select Through All. and. .. 11. Click on front face and select Sketch. . Click Corner Rectangular and sketch rectangular start form bottom left edge to right edge.. Beginner Part 1: My First Solid. 6.
(10) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 1: My First Solid. www.solidworkstutorials.com. Click Smart Dimension and set rectangular height to 0.1in.. 12. Click Extruded Boss/Base. Style and select Isometric.. Beginner Part 1: My First Solid. set Direction 1 to 0.5in. and. . Click Display. 7.
(11) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 1: My First Solid. www.solidworkstutorials.com. 13. Click Fillet. , check Full preview. add fillet to all edges. Beginner Part 1: My First Solid. 8.
(12) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 1: My First Solid. www.solidworkstutorials.com. and. .. 14. Save it?. the part as Bracket and you’re done! Simple isn’t. Go to table of contents Go to beginning of chapter tutorial Go to www.solidworkstutorials.com. Beginner Part 1: My First Solid. 9.
(13) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com. Beginner Part 2: Sketching Sketch is the base of your part, it’s a good practice to master sketching in SolidWorks.... 1.. Click New. 2.. Click Front Plane, insert sketch on plane by click Sketch.. 3.. Click Sketch. , click Part. , OK.. In this tutorial you will make this box, start from sketch and build features. You’ll learn how to use sketch tools to build this part.. , click. Corner Rectangular . Start first point at origin and click another point at top right side.. 4.. Beginner Part 2: Sketching. Click Smart Dimension , click top edge set dimension to 2in and click right edge set dimension to 2in.. 10.
(14) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com 5.. To build features, click Features>Extruded Boss/Base. , set D1 to 0.50in. and. Beginner Part 2: Sketching. .. 11.
(15) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. Beginner Part 2: Sketching. www.solidworkstutorials.com 6.. Click on front face of the part, click Normal To.. 7.. Click on front face and click Sketch.. 12.
(16) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com. 8.. Click Offset Entities. , set to 0.1in and check. Reverse box. 9.. Beginner Part 2: Sketching. Click Extruded Cut. and. .. , change D1 to 0.4in.. 13.
(17) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com 10. Click on side face, click Sketch.. 11. While pressing Ctrl key select inner left and right edge.. Click. Convert Entities. .. 12. Select Centerline from line menu , sketch a centerline midpoint to midpoint of both converted. Beginner Part 2: Sketching. 14.
(18) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com. edges. 13. Click sketched centerline. and click Offset Entities.. Beginner Part 2: Sketching. 15.
(19) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com. Set Parameter, D to 0.3in check Bi-directional and. .. 14. Now click Trim Entities to remove excess line, before make any cut make sure under option Trim to. closest is selected. Trim extra line as below sketch. Answers Yes if notification appear.. 15. Click View Orientation>Isometric.. 16. Click Features>Extruded Boss/Base , for Direction 1, click Reverse Direction (green box) and set D1 to 0.1in.. Beginner Part 2: Sketching. 16.
(20) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com. and. Beginner Part 2: Sketching. .. 17.
(21) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com 17. Click on front face and click Normal To.. 18. Click on front face and click Sketch.. Beginner Part 2: Sketching. 18.
(22) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com. 19. Click Circle,. sketch circle at left edge.. 20. Click Smart Dimension, below sketch.. 21. Click on sketched circle,. Copy Entities.. Beginner Part 2: Sketching. dimension sketch as. click. Set delta x. 19.
(23) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com. to 0.3in. and. .. 22. Click Centerline, sketch centerline across front face and make sure it starts at midpoint left edge and midpoint right edge and. .. 23. While press Ctrl key, select both sketched circle and click Mirror Entities , on Mirror Option click Mirror about: box, and select centerline. Beginner Part 2: Sketching. 20.
(24) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com. and 24. Click Extruded Cut,. and set D1 to 0.1in. 25. Click View Orientation>Back,. Beginner Part 2: Sketching. .. and. .. 21.
(25) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com and click on back face and click Sketch.. 26. Click Sketch>Circle,. sketch circle at lower left edge.. Click Smart. Dimension sketch below.. and dimension sketched circle as. and. Beginner Part 2: Sketching. .. 22.
(26) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com. 27. Click on sketched circle,. and click. Linear Sketch Pattern and on Direction 1 set D1 to 1.2in and on Direction 2, change # to 2 and set D2 to 1.2in and. Beginner Part 2: Sketching. .. 23.
(27) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 2: Sketching. www.solidworkstutorials.com. 28. Click Features>Extruded Cut,. and set direction to. Through All Click View Orientation>Isometric.. 29. Save it?. and. .. the part as Sketch and you’re done! Simple isn’t. Go to table of contents Go to beginning of chapter tutorial Go to www.solidworkstutorials.com. Beginner Part 2: Sketching. 24.
(28) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 3: Turning Part. www.solidworkstutorials.com. Beginner Part 3: Turning Part Some parts such as pins and shafts can be manufacture by turning process on lathe machine, we can create turning part by revolving it sketch on it axis.... In this tutorial you will make this pin, start from sketch and build solid body by revolve it sketch on axis. You’ll learn how to use revolved boss/base and revolved cut to build this part.. 1.. Click New,. click Part,. OK.. 2.. Click Front Plane, insert sketch on plane by click Sketch.. 3.. Click on Line, sketch a closed loop start at origin, sketch as sketch below end back at origin.. and. 4.. Click Smart Dimension sketch below.. and 5.. Beginner Part 3: Turning Part. and dimension sketch as. .. Click Features>Revolved Boss/Base, and click on bottom line as it axis.. 25.
(29) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 3: Turning Part. www.solidworkstutorials.com. and. 6.. Beginner Part 3: Turning Part. .. Click View Orientation>Front and click Front Plane and click Sketch.. 26.
(30) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 3: Turning Part. www.solidworkstutorials.com. 7.. Click Corner Rectangle, and sketch rectangle overlap on solid body as sketched below.. and. .. 8.. Click Smart Dimension sketched below.. 9.. To view solid body axis, click View>Temporary Axes.. and dimension sketch as. 10. To make second undercut, click Features>Revolved Cut and select temporary axes as it axis. Beginner Part 3: Turning Part. 27.
(31) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 3: Turning Part. www.solidworkstutorials.com. and. Beginner Part 3: Turning Part. .. 28.
(32) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 3: Turning Part. www.solidworkstutorials.com 11. To hide temporary axes, click View>Temporary Axes.. 12. Save. the part and you’re done! Simple isn’t it?. Go to table of contents Go to beginning of chapter tutorial Go to www.solidworkstutorials.com. Beginner Part 3: Turning Part. 29.
(33) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 4: Hole Wizard. www.solidworkstutorials.com. Beginner Part 4: Hole Wizard Hole Wizard is used for creating predefined and standard holes such as counter bore hole, counter sunk hole, screw clearance hole and many more.... In this tutorial you will add counterbore, countersink and tap holes to this plate by using Hole Wizard tools.. 1.. Click New,. 2.. Click Top Plane, insert sketch on plane by click Sketch.. 3.. Click on Corner Rectangle, origin.. and. 4.. Beginner Part 4: Hole Wizard. OK.. sketch a rectangle start at. .. Click Smart Dimension sketch below.. and 5.. click Part,. and dimension sketch as. .. Click Features>Extruded Boss/Base, set D1 to 1in. on Direction 1. 30.
(34) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 4: Hole Wizard. www.solidworkstutorials.com. 6.. 7.. Beginner Part 4: Hole Wizard. and . Click on top face and click Normal To.. Click Features>Hole Wizard on Hole Type, select Counterbore, Standard to Ansi Inch, Type to Socket Head Cap Screw, Size to #10, Fit to Normal and End Condition to Through All.. 31.
(35) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 4: Hole Wizard. www.solidworkstutorials.com. For positions placement for this counterbore hole, click on Positions tab. more positions at each edge.. Beginner Part 4: Hole Wizard. Now click three. 32.
(36) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 4: Hole Wizard. www.solidworkstutorials.com. 8.. Click on Smart Dimensions, click on center point of counterbore hole and click left edge, set dimension to 0.5in.. Continue dimensioning as sketched below.. 9.. and . For adding countersink at center, click on top face and click on Hole Wizard. Beginner Part 4: Hole Wizard. .. 33.
(37) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 4: Hole Wizard. www.solidworkstutorials.com. On Hole Type, select Countersink, Standard to Ansi Inch, Type to Flat Head Screw (100), Size to #10, Fit to Normal and End Condition to Through All. 10. For positions placement for this countersink holes, click on Positions tab. more positions at center.. Beginner Part 4: Hole Wizard. Now click three. 34.
(38) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 4: Hole Wizard. www.solidworkstutorials.com. 11. Click on Smart Dimensions, click on center point of countersink hole and click left edge, set dimension to 2.5in.. Continue dimensioning as sketched below.. and . 12. For adding center tap hole, click on top face at center and click Hole Wizard.. Beginner Part 4: Hole Wizard. 35.
(39) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 4: Hole Wizard. www.solidworkstutorials.com. On Hole Type, select Tap, Standard to Ansi Inch, Type to Tapped hole, Size to 1/2-13, End Condition to Through All. 13. For positions placement for this tap hole, click on Positions tab. There is another style to positions hole wizard is define it position by sketch, let try it.. Click on Centerline, Sketch a horizontal line start at midpoint of left edge to midpoint left. Beginner Part 4: Hole Wizard. 36.
(40) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 4: Hole Wizard. www.solidworkstutorials.com edge. Press Esc to end sketch centerline.. 14. Click and drag tap center to midpoint of centerline.. and . 15. Click View Orientation>Isometric. Done.. Beginner Part 4: Hole Wizard. 37.
(41) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 4: Hole Wizard. www.solidworkstutorials.com. 16. Save. the part as Plate1 and you’re done! Simple isn’t it?. Go to table of contents Go to beginning of chapter tutorial Go to www.solidworkstutorials.com. Beginner Part 4: Hole Wizard. 38.
(42) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 5: Pattern. www.solidworkstutorials.com. Beginner Part 5: Pattern Pattern (or some called array) is used to repeat features in linear arrangement or circular arrangement. It’s good to know how to optimize these tool, it help you make your part faster and easier.... 1. In this tutorial you will add multiple 2. features as linear pattern and circular pattern using pattern tools.. 3.. Click New,. Click on Corner Rectangle, origin.. Beginner Part 5: Pattern. sketch a rectangle start at. .. Click Smart Dimension sketch below.. and 5.. OK.. Click Top Plane, insert sketch on plane by click Sketch.. and. 4.. click Part,. and dimension sketch as. .. Click Features>Extruded Boss/Base, set D1 to 1in. on Direction 1. 39.
(43) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 5: Pattern. Beginner Part 5: Pattern. www.solidworkstutorials.com. 6.. and . Click on top face and click Normal To.. 7.. Click on top face and click Sketch.. 40.
(44) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 5: Pattern. www.solidworkstutorials.com. Click on Circle. and sketch a circle on top face and. 8.. Click on Smart Dimension sketched circle as sketch below.. 9.. Click Features>Extruded Cut. Through All.. .. and dimension. on Direction 1 set to. and. .. 10. Click Features>Hole Wizard on Hole Type, select Counterbore, Standard to Ansi Inch, Type to Socket Head Cap Screw, Size to #10, Fit to Normal and End Condition to Through All.. Beginner Part 5: Pattern. 41.
(45) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 5: Pattern. www.solidworkstutorials.com. For positions placement for this counterbore hole, click on Positions tab. at lower left edge.. Beginner Part 5: Pattern. Click one point. 42.
(46) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 5: Pattern. www.solidworkstutorials.com. 11. Click on Smart Dimension sketched circle as sketch below.. and. and dimension. .. 12. To pattern this counterbore hole, click on CBORE for #10 Socket Head Cap Screw1. and click Linear Pattern. Direction 1 pattern.. Beginner Part 5: Pattern. Click on bottom edge as. 43.
(47) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 5: Pattern. www.solidworkstutorials.com. Set D1 to 2.5in and pattern # to 3. Click on highlighted arrow to switch it directions.. 13. Click on left edge as Direction 2 pattern.. Set D2 to 3.4in and number of pattern # to 2. You can click. Beginner Part 5: Pattern. 44.
(48) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 5: Pattern. www.solidworkstutorials.com on arrow to switch it directions.. and. .. 14. Click on top face and click Sketch.. Click on Circle,. Beginner Part 5: Pattern. sketch a circle with center to open hole.. 45.
(49) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 5: Pattern. www.solidworkstutorials.com. Click Smart Dimension, 1.5in.. set circle diameter to. 15. Click Line, sketch a vertical line crossing sketch circle at 12 o’clock to 6 o’clock.. Press Esc key to end Line. Exit sketch. 16. Click on Hole Wizard, on Hole Type click on Tap, Standard: Ansi Inch, Type: Tapped Hole, Hole Specifications Size:1/4-20, End Condition Through All.. Beginner Part 5: Pattern. 46.
(50) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 5: Pattern. www.solidworkstutorials.com. For positions placement for this tap hole, click on Positions tab. o’clock last sketched circle.. Beginner Part 5: Pattern. Click one point at 12. 47.
(51) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 5: Pattern. www.solidworkstutorials.com. and. .. 17. To hide guide sketch, click Sketch4 and click Hide.. 18. To pattern tap hole, click on 1/4-20 Tapped Hole1. and click Circular Pattern.. Change view to isometric by click on View Orientation>Isometric. Click on open inner hole face as it’s pattern axis, set instances # to 6 and. Beginner Part 5: Pattern. .. 48.
(52) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 5: Pattern. www.solidworkstutorials.com. 19. Save. the part as Block and you’re done! Simple isn’t it?. Go to table of contents Go to beginning of chapter tutorial Go to www.solidworkstutorials.com. Beginner Part 5: Pattern. 49.
(53) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. Beginner Part 6: Assembly Parts Assembly is a part of design process, it show how all designed parts work together as a single unit. .... 1.. Click New,. click Part,. OK.. 2.. Click Front Plane, insert sketch on plane by click Sketch.. 3.. Click on Corner Rectangle, origin.. In this tutorial you will create this toy horse by assembly parts to one unit assembly.. and. 4.. 5.. Beginner Part 6: Assembly Parts. .. Click Smart Dimension sketch below.. and. sketch a rectangle start at. and dimension sketch as. .. Click Features>Extruded Boss/Base, set D1 to 4in. on Direction 1. 50.
(54) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. 6.. Beginner Part 6: Assembly Parts. and . Click on right face and click Normal To.. 51.
(55) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com 7.. Click on right face again and click Sketch.. Click on Circle. and sketch 4 circle at each corner. Click. on Smart Dimension sketched below.. 8.. Click on Features>Extruded Cut. Through All on View OrientationIsometric.. Beginner Part 6: Assembly Parts. and dimension sketch as. and set Direction 1 to. and. . Click. 52.
(56) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. 9.. Click on top face and click Normal To.. Click on top face again and click Sketch.. Beginner Part 6: Assembly Parts. 53.
(57) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. Click on Corner Rectangle top and bottom.. Click on Smart Dimension rectangles as sketched below.. Beginner Part 6: Assembly Parts. and sketch 2 rectangles at. and dimension these. 54.
(58) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. 10. Click on Features>Extruded Cut 1.0in. and set Direction 1 to. and . Click on View Orientation>Isometric.. Beginner Part 6: Assembly Parts. 55.
(59) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. 11. Save. the part as Body.. 12. Click New,. click Part,. OK.. 13. Click Right Plane, insert sketch on plane by click Sketch.. 14. Click on Corner Rectangle, origin.. and. Beginner Part 6: Assembly Parts. sketch a rectangle start at. .. 56.
(60) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. 15. Click Smart Dimension sketch below.. and dimension sketch as. 16. Click Centerline and sketch vertical centerline through top edge midpoint to bottom midpoint. Press Esc to end centerline.. Beginner Part 6: Assembly Parts. 57.
(61) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. 17. Click on Circle,. sketch 3 circles onto centerline and. using Smart Dimension sketched below.. dimension sketch as. 18. Click Features>Extruded Boss/Base, set D1 to 0.25in. and. on Direction 1. . Click on View. Orientation>Isometric.. Beginner Part 6: Assembly Parts. 58.
(62) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. 19. To change part color, right click on Part2>Appearance>Appearance. On Color select Shiny and pick white color.. and 20. Save. the part as Leg.. 21. Click New,. Beginner Part 6: Assembly Parts. .. click Part,. OK.. 59.
(63) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com 22. Click Right Plane, insert sketch on plane by click Sketch.. 23. Click on Circle,. Dimension. and sketch a circle. Click Smart. dimension this circle to 0.25in.. 24. Click Features>Extruded Boss/Base, set D1 to 0.25in. and. on Direction 1. .. 25. Click on right face and click Normal To.. Click on this face again and click Sketch.. Beginner Part 6: Assembly Parts. 60.
(64) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. 26. Click on Circle,. Dimension. and sketch a circle. Click Smart. dimension this circle to 1.5in.. 27. Click Features>Extruded Boss/Base, set D1 to 0.25in. and. on Direction 1. .. 28. To change part color, right click on Part3>Appearance>Appearance. Beginner Part 6: Assembly Parts. 61.
(65) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. On Color select Standard and pick red color.. and. 29. Save. .. the part as Wheel.. 30. Click New,. click Part,. OK.. 31. Click Right Plane, insert sketch on plane by click Sketch.. Beginner Part 6: Assembly Parts. 62.
(66) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. 32. Click on Line,. and sketch a horse head.. 33. Click on Smart Dimension as sketched below.. and dimension sketch. 34. Click Features>Extruded Boss/Base, set D1 to 0.5in. and 35. To change part color, right click on Part4>Appearance>Appearance. Beginner Part 6: Assembly Parts. on Direction 1. .. 63.
(67) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. On Color select Shiny and pick white color.. and. 36. Save. the part as Head.. 37. Click New,. Beginner Part 6: Assembly Parts. .. click Part,. OK.. 64.
(68) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com 38. Click Right Plane, insert sketch on plane by click Sketch.. 39. Click on Line,. and sketch a horse tail.. 40. Click on Smart Dimension as sketched below.. Beginner Part 6: Assembly Parts. and dimension sketch. 65.
(69) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. 41. Click Features>Extruded Boss/Base, set D1 to 0.5in. and 42. To change part color, right click on Part5>Appearance>Appearance. on Direction 1. .. On Color select Shiny and pick white color.. Beginner Part 6: Assembly Parts. 66.
(70) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. and. 43. Save. .. the part as Tail.. Let’s begin assembly all this parts.. 44. Click New, click Assembly, OK. 45. To add part in assembly, Click Browse…. Beginner Part 6: Assembly Parts. 67.
(71) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com Select Body.sldprt and click Open. Click on workspace.. 46. To add leg part, click Insert Components Browse…. Beginner Part 6: Assembly Parts. , click. 68.
(72) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com Select Leg.sldprt and click Open. Click on workspace.. 47. To add wheel part, click Insert Components click Browse…. Beginner Part 6: Assembly Parts. ,. 69.
(73) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com Select Wheel.sldprt and click Open. Click on workspace.. 48. Each of this part need to be mate together, click Mate click on body right face. and turn the assembly around (click wheel button and turn model) click on leg inner face.. Beginner Part 6: Assembly Parts. 70.
(74) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. Coincident mate already pre selected, click 49. Turn the assembly back to previous view.. Beginner Part 6: Assembly Parts. .. 71.
(75) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com 50. Click on inner hole face on body and inner hole of leg.. The Concentric mate already pre selected, click this step for bottom hole.. . Repeat. and . 51. Turn the assembly the other way.. Beginner Part 6: Assembly Parts. 72.
(76) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com 52. Click on wheel shaft face and inner leg hole.. Concentric mate already pre selected, click 53. Click on inner wheel face. .. turn the assembly to left side and click on outer leg face.. Coincident mate already pre selected, click . 54. Repeat step 46 – 53 for other set of legs and wheels.. 55. To add head part, click Insert Components click Browse…. Beginner Part 6: Assembly Parts. ,. 73.
(77) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. Select Head.sldprt and click Open. Click on workspace. To. add tail part, click Insert Components Browse…. , click. Select Tail.sldprt and click Open. Click on workspace.. Beginner Part 6: Assembly Parts. 74.
(78) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. 56. Click Mate. , click on tail face,. turn assembly the other way, and click on back face cut.. Coincident mate already pre selected, click 57. Click on side face of body cut,. .. turn assembly to left and click on side face of tail,. Beginner Part 6: Assembly Parts. 75.
(79) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. Coincident mate already pre selected, click 58. Click on top edge of tail,. .. turn assembly to view top body and click on top face of the body.. Coincident mate already pre selected, click . 59. Turn the model to facing front of the body, click on side face of inner cut,. Beginner Part 6: Assembly Parts. 76.
(80) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. turn the assembly to left and click on head side face.. Coincident mate already pre selected, click 60. Click on inner cut face of the body,. .. turn the assembly around and click on back head face.. Beginner Part 6: Assembly Parts. 77.
(81) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com. Coincident mate already pre selected, click . 61. Turn the assembly to view front side, click on head lower edge,. and click on body bottom inner cut.. Coincident mate already pre selected, click. Beginner Part 6: Assembly Parts. .. 78.
(82) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 6: Assembly Parts. www.solidworkstutorials.com 62. Click View Orientation>Isometric. and you’re done!. 63. Save isn’t it?. the assembly as Horse and you’re done! Simple. Go to table of contents Go to beginning of chapter tutorial Go to www.solidworkstutorials.com. Beginner Part 6: Assembly Parts. 79.
(83) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. Beginner Part 7: Detailing Drawing Once solid parts created we need to transfer it to engineering drawing so the others can understand your parts…. 1.. Click New,. click Drawing,. OK.. 2.. On Sheet Format/Size select A – Landscape and OK.. 3.. Click Browse.... In this tutorial you create drawing for this part.. locate you Block.sldprt (Part from Beginner Part 5: Pattern tutorials). Beginner Part 7: Detailing Drawing. 70.
(84) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. 4.. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. Click Open. For Orientation select Top and for Display Style select Hidden Lines Visible,. 71.
(85) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing 5.. www.solidworkstutorials.com Click on sheet to add this view,. click again on left side to add side view of the part,. click once more to upper right of sheet to view it’s 3D view.. Beginner Part 7: Detailing Drawing. 72.
(86) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. 6.. 7.. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. Click . Repositions part 3D view to upper right corner of the sheet by dragging it to this location.. There is no centerline for holes in side view, let’s add this centerline, click on side view,. 73.
(87) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. Click on Annotation tab,. click on Centerline,. centerline automatically added to side view, click. 8.. Beginner Part 7: Detailing Drawing. Click Smart Dimension and pull dimension to bottom.. .. and click on bottom edge. 74.
(88) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. 9.. www.solidworkstutorials.com. Zoom in, click on center hole edge,. click on counter bore hole edge. and pull dimension to bottom side.. Beginner Part 7: Detailing Drawing. 75.
(89) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 10. Click on center hole edge,. click on counter bore hole edge. Beginner Part 7: Detailing Drawing. 76.
(90) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. and pull dimension to bottom side.. 11. Repeat step 10 and continue dimension for the third counter bore hole.. Beginner Part 7: Detailing Drawing. 77.
(91) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. Beginner Part 7: Detailing Drawing. 78.
(92) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 12. Click on center hole edge,. click on left edge. and pull dimension to bottom side.. Beginner Part 7: Detailing Drawing. 79.
(93) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 13. Repeat step 12 for right edge.. Beginner Part 7: Detailing Drawing. 80.
(94) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 14. Click on center hole edge and pull out it’s diameter dimension.. Beginner Part 7: Detailing Drawing. 81.
(95) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 15. Click on thread diameter and pull out its radius dimension.. Beginner Part 7: Detailing Drawing. 82.
(96) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 16. Click on center hole edge,. click on counterbore hole edge. and pull it’s dimension to left side.. Beginner Part 7: Detailing Drawing. 83.
(97) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 17. Click on center hole edge,. click on bottom edge. and pull it’s dimension to left side.. Beginner Part 7: Detailing Drawing. 84.
(98) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 18. Repeat steps 16 and 17 for top counterbore and top edge.. 19. Click. to end Smart Dimension. Click on Annotation tab,. click on Hole Callout.. Click on counterbore hole. and pull out its hole callout to right side.. Beginner Part 7: Detailing Drawing. 85.
(99) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 20. Click on thread. and pull out its hole callout to right side.. Click. Beginner Part 7: Detailing Drawing. to end hole callout annotation.. 86.
(100) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 21. Click on Sketch tab,. Click on Centerline, sketch a centerline thru center of Block. Point (hover your cursor) to midpoint of left edge (don’t click),. move you cursor to left side,. now click on sheet and click again on right side.. Press Esc to end centerline.. Beginner Part 7: Detailing Drawing. 87.
(101) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 22. Click on centerline,. click on View Layout tab,. click on Section View, check Flip Direction. on section Line option,. and click on sheet for this section view.. Beginner Part 7: Detailing Drawing. 88.
(102) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 23. You can customize each view how it’s appear on drawing by changing it’s display style. Click on Section A-A view,. on Display Style click on Hidden Line Removed.. Click. Beginner Part 7: Detailing Drawing. . Your section view now changed.. 89.
(103) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 24. Click on 3D view,. on Display Style click on Shaded With Edges.. To change it’s scale, under Scale click on Use custom scale, set to 1:3. and. Beginner Part 7: Detailing Drawing. .. 90.
(104) Buyer: muhammad rodhy ([email protected]) Transaction ID: 1XA19981EN783182K. Beginner Part 7: Detailing Drawing. www.solidworkstutorials.com. 25. Save it?. the drawing as Block and you’re done! Simple isn’t. Go to table of contents Go to beginning of chapter tutorial Go to www.solidworkstutorials.com. Beginner Part 7: Detailing Drawing. 91.
(105)
Related documents
– Click Select a Certificate Store, Select *SYSTEM, then Click Continue. – Enter a password in the Certificate store password field and Click Continue. – Click Manage
• provide clear information about grading policies and assignment requirements in the course syllabus, and • communicate any changes to assignments and/or to the course calendar
(11) Inform participants that the maintenance phase of the program will last 6 months following completion of the core curriculum, during which time the facilitator and participant
low prices seo software reviews cnet seo content software scam or work instant access for seo software seo company feeder seo client finder seo client finding tool seo
Client exports out existing data and removes all records they do NOT want in the new system Client formats into excel spreadsheet format as provided by vendor and sends to us
In the case of the actual behaviour of currently studying at the time of measurement of childbearing intentions, the differences in the predicted probabil- ities are
Click start and find the application called BIG-IP Edge Client under all programs and click on it or click on your system tray and double-click on the BIG-IP Edge icon here. Click
Factory wired 18AWG Field wired DISCONNECT SWITCH (OPTIONAL) 230 VAC L1 HOT (YELLOW) L2 HOT (YELLOW) YELLOW WHITE L H FAN MOTOR THERMOSTAT (OPTIONAL) BLACK BLACK RED RED HIGH
