ta
ble
of
co
nte
nt
s
1 Scope of delivery ... 02 2 Mounting ... 03 2.1 Mounting preparation2.2 Mounting on cavity walls / lightweight walls ... 04 2.2.1 Wall notch
2.2.2 Angles
2.2.3 Insert the lower case 2.2.4 Adjust the frame 2.2.5 Insert the tablet 2.2.6 Close the cover case
2.3 Mounting on solid walls ... 07 2.3.1 Wall notch
2.3.2 Mount the lower case 2.3.3 Insert the tablet 2.3.4 Close the cover case
3 Anti-theft-protection ... 09 (only for the products with anti-theft-protection)
sc
ope
of
del
iver
y
4x hexagon socket head cap screw M4x86x stud screw M5x62x angle 1x lower case 1x case cover
1x hex-wrench (only for the products with anti-theft-protection) 1
1. Scope of delivery
2 3 4 5 6 1 2 3 4 5 6Before installing, please consider the following instructions:
1. Do not install or use TabLines TWE in humid or wet environment.
2. The installation location for the wall mount and cabels has to be deep enough.
3. Select a location with sufficient Wi-Fi signal to make sure that all features of your tablet work correctly. 4. Draw the dimensions on the wall to prepare the notch. The measures/dimensions of the wall cut-out are
different, depending on whether you have bought a TWE tablet wall installation for the Samsung Galaxy Tab 4 10.1 or for the Samsung Galaxy Tab 3 10.1.
Dimensions for the notch:
Samsung Galaxy Tab 4 10.1: 291 x 230 x 15 mm Samsung Galaxy Tab 3 10.1: 219 x 289 x 17 mm
Engineering drawings of the TWE models:
2. Mounting
2.2.2 Angles
Depending on the wall, TabLines TWE can be used with or without the provided angles. Mounting without angles:
If the lower case of the TabLines TWE is flat against the wall, you can mount the frame directly on the backside of the wall. You don´t need the angles.
If the distance is too large, attach a piece of wood (e.g.) with the required depth and mount the frame.
Mounting with angles:
If the cavity is too big, you need the angles. Mount the angles for example with two pieces of wood in the notch. Mount the frame on the angles.
Mind the needed depth! 2.2.1 Wall notch
Select an area of the wall and draw the dimensions on it (leightweight walls). Cut out the selected area.
Check the needed depth!
Fig. 3: Mark the position
2.2 Mounting on cavity walls/ lightweight walls
Fig. 4: Mounted angles
wall/ lightweight wall, please follow the continuing instruction (2.2). If you have a solid wall, skip the step 2.2 and continue with 2.3.
3
2.2.3 Insert the lower case
Position the lower case on the angles and fix the case with the delivered M4-bolts on the angles (fig. 5).
Make sure that all screws have been tightened!
2.2.4 Adjust the frame
Because of the elongated holes in the lower case you can easily adjust the frame horizontally, even after tightening on the wall. When the TabLines TWE is in the desired position, tighten the screws again.
With the M5-screws you can do minor adjustments of the build-in depth of the frame to correct mistakes from before.
Fig. 5: Mounting the lower case
Fig. 6: Frame can be adjusted
2
1 4
2.2.5 Insert the tablet
Make sure that the homebutton of the tablet is at the bottom.
Insert the tablet (fig. 7) between the insert strips (the insert strips are already attached).
Make sure that the Samsung Galaxy Tab don´t fall down during the installation. If possible, hold it the whole time until the cover is hooked in.
2.2.6 Close the cover case
Hook the case cover into the lower case . Make sure that the cover case is hooked into the screws (fig. 8).
You can still select the homebutton after closing the cover.
Your tablet is mounted!
Fig. 7: Integrated Samsung Galaxy Tab
Fig. 8: Hook in the case cover
4 5
2.3.2 Mount the lower case
After cutting out the notch you can just screw the lower case on the wall. Use the supplied M4 screws .
Instead of the screws, you can also use special glue, foam or tape.
2.3 Mounting on solid walls
2.3.1 Wall notch
Select an area of the wall and draw the dimensions on it.
Cut out or milling the selected area. Check the needed depth! The cover of the TWE has to be later flush on the wall.
Fig. 9: Mark the position
Fig. 10: Sticked lower case
2.3.3 Insert the tablet
Make sure that the homebutton of the tablet is at the bottom.
Insert the tablet (fig. 11) between the insert strips (the insert strips are already attached). Make sure that the Samsung Galaxy Tab don´t fall down during the installation. If possible, hold it the whole time until the cover is hooked in.
2.3.4 Close the cover case
Hook the case cover into the lower case . Make sure that the cover case hooked into the screws (fig. 12).
You can still select the homebutton after closing the cover.
Your tablet is mounted!
Fig. 11: Integrated Samsung Galaxy Tab
Fig. 12: Hook in the case cover
4 5
3. Anti-theft-protection
Use the provided hex-wrench to screw the safety bolt in front of the case. The safety bolt is already integrated in the case.
The anti-theft-protection prevents, that an unauthorised person can open the case.
Fig. 13: Tighten the security screw
Please note that you can only use this function, if you have purchased a TabLines TWE model with anti-theft-protection. The anti-theft-protection cannot be added subsequently.