Ip-10 Cli Command Line

(1)

CLI COMMAND LINE

Aug 2008

(2)

1.

1. Document Purpose

Document Purpose

The purpose of this document is to

The purpose of this document is to describe the basic configuration steps of IP-10describe the basic configuration steps of IP-10 through the CLI interface radio link.

through the CLI interface radio link.

2.

2. Document

Document Scope

Scope

This document describes the recommended initial steps in order to connect and This document describes the recommended initial steps in order to connect and manage IP-10 radio link through the CLI Interface. It includes t

manage IP-10 radio link through the CLI Interface. It includes the configuration stepshe configuration steps of the following main sections:

of the following main sections:

•

• Connecting to IDU using default factory setupConnecting to IDU using default factory setup •

• Launching the hyper terminalLaunching the hyper terminal •

• _{SW Upgrade}_{SW Upgrade} •

• _{License key activation}_{License key activation} •

• _{Basic parameters configuration}_{Basic parameters configuration}

3.

3. Startup

Startup Configuration

Configuration Steps

Steps

Basic configuration includes the following basic steps: Basic configuration includes the following basic steps: 1.

1. Complete physicaComplete physical HW installation l HW installation of IDU, IF coax of IDU, IF coax cable, RFU acable, RFU and antenna nd antenna as peras per installation instructions.

installation instructions. 2.

2. Connect PC Connect PC to IDU ato IDU and Launch nd Launch the Hypethe Hyper terminal.r terminal. 3.

3. Upgrade Upgrade IDU IDU SW.SW. 4.

4. Load Load license license key.key. 5.

5. Configure Configure radio radio link link parameters.parameters. 6.

(4)

Getting Started

To log in to the CLI: To log in to the CLI: 1. Power on your PC. 1. Power on your PC. 2. Make sure that your PC

2. Make sure that your PC is connected to the management port on is connected to the management port on the front panel of the front panel of the IP-10 unit.

the IP-10 unit.

3. For a first-time login, use the following: 3. For a first-time login, use the following: User: admin

User: admin Password: admin Password: admin

Note:

Note:_{When using the Hyper Terminal, you should set the}_{When using the Hyper Terminal, you should set the terminal speed (in your PC}_{terminal speed (in your PC}

terminal terminal

Configuration) to 115200 kpbs. In addition, it is recommended to

Configuration) to 115200 kpbs. In addition, it is recommended to select the VT-100select the VT-100 terminal type and set the

terminal type and set the Terminal size to 24 rows, 80

Terminal size to 24 rows, 80 columns.columns.

SOME COMMAN COMMAND SOME COMMAN COMMAND

IP-10:/> IP-10:/> Name -Info Name -Info ---ls

ls list list entitiesentities get

get get get parameterparameter set

set set set parameterparameter help help

help help cd

cd change change directorydirectory exit

exit exit exit CLICLI logout

logout logout logout from from CLICLI cli-ver

cli-ver cli versioncli version cls

cls clear clear screenscreen shell

shell enter enter secondary secondary shellshell write

write Write Write the the current current switch switch configuration configuration into into configuration configuration filefile show-tree

show-tree Show Show entity entity treetree find

find Search Search for for a a string string in in the the parameter's parameter's entity entity name name and and informationinformation fields

(5)

IP-10

MAIN MANU

IP-10:/> ls

management - Management management - Management platform - Platform platform - Platform radio - Radio radio - Radio interfaces - Interfaces interfaces - Interfaces diagnostics - Diagnostics diagnostics - Diagnostics xml-interface - XML Interface xml-interface - XML Interface

Management Command Line

1. 1. Check

Check the

the IP

IP Address

Address

IP-10:/> get management/networking/ip-address/ip-address IP-10:/> get management/networking/ip-address/ip-address↵↵

192.168.1.10 192.168.1.10

2. 2. Change

Change the IP

the IP Address

Address

IP-10:/> set

IP-10:/> set management/nmanagement/networking/ip-addetworking/ip-address/ip-address 192.168.1.20ress/ip-address 192.168.1.20↵↵

You may lose remote management connection to the unit if

You may lose remote management connection to the unit if this value isthis value is changed i

changed i icorrectly. icorrectly.

Are you sure? (Yes/no):yes Are you sure? (Yes/no):yes↵↵

3. Check Subnet Mask

IP-10:/> get management/networking/ip-address/subnet-mask IP-10:/> get management/networking/ip-address/subnet-mask↵↵

255.255.255.0 255.255.255.0 4.

4. Change Change Subnet Subnet MaskMask IP-10 :/>

(6)

5. Check default gateway 5. Check default gateway

IP-10:/>

IP-10:/> get get management/nemanagement/networking/ip-addtworking/ip-address/default-gatewaress/default-gatewayy↵↵

0.0.0.0 0.0.0.0

6. Change default gateway 6. Change default gateway

IP-10:/>

IP-10:/> set set management/netwmanagement/networking/ip-addrorking/ip-address/default-gateway 192.168.1.10ess/default-gateway 192.168.1.10↵↵

7.Check HW Address 7.Check HW Address

IP-10:/>

IP-10:/> get get managemenmanagement/networking/ip-adt/networking/ip-address/hw-addredress/hw-addressss↵↵

00:0A:25:00:19:23 00:0A:25:00:19:23

8.Check management port 8.Check management port IP-10:/>

IP-10:/> get get managemenmanagement/networking/numbt/networking/number-of-portser-of-ports↵↵

3 3

9. Create Management Port 9. Create Management Port IP-10:/> set

IP-10:/> set management/nemanagement/networking/numbetworking/number-of-ports 2r-of-ports 2↵↵

10. Check Vlan ID 10. Check Vlan ID

IP-10:/> get

IP-10:/> get management/nemanagement/networking/vlantworking/vlan↵↵

1 1

11. Create Vlan IP 11. Create Vlan IP

IP-10:/> set

IP-10:/> set management/nemanagement/networking/vlan 2tworking/vlan 2↵↵

12. Check Management Type 12. Check Management Type

IP-10:/> get

IP-10:/> get management/nemanagement/networking/typetworking/type↵↵

in-band in-band

(7)

IP-10

19. Set to

19. Set to Default ConfigurationDefault Configuration IP-10:/>

IP-10:/> /managemen/management/mng-services/cfg-service/set-tot/mng-services/cfg-service/set-to-default-default You are about to set

You are about to set the unit configuration to its default the unit configuration to its default values.values. This operation will take effect only

This operation will take effect only after a unit reset.after a unit reset. Are you sure? (yes/no):no

Are you sure? (yes/no):no

22. Showing current Alarm 22. Showing current Alarm

IP-10:/>

IP-10:/> /management/mn/management/mng-services/alarm-g-services/alarm-service/alarm-curreservice/alarm-current/shownt/show Date&Time

Date&Time Severity Severity AlarmName AlarmName Origin Origin TextText IP-10:/>

IP-10:/> get get /management/mn/management/mng-services/alarm-g-services/alarm-service/alarm-curreservice/alarm-current/most-severent/most-severe cleared

cleared

25. Check and update Date and Time 25. Check and update Date and Time

IP-10:/>

IP-10:/> get get management/mnmanagement/mng-services/time-servg-services/time-service/time-and-dateice/time-and-date 27-11-2008,11:42:38

27-11-2008,11:42:38 IP-10:/>

IP-10:/> set set management/mmanagement/mng-services/time-serviceng-services/time-service/time-and-date 27-11-/time-and-date 27-11-2008,11:50:01

2008,11:50:01

33.Protection Enable Disable 33.Protection Enable Disable IP-10:/> get

IP-10:/> get platform/mate-iduplatform/mate-idu/protection-admin/protection-admin disable

disable IP-10:/> se

IP-10:/> set t platform/mate-idu/pplatform/mate-idu/protection-adminrotection-admin disable enable

disable enable IP-10:/> set

(8)

35. Set TX/RX Frequency 35. Set TX/RX Frequency

IP-10:/> get

IP-10:/> get radio/rfu/tx-freqradio/rfu/tx-freq 14515000

14515000 IP-10:/> set

IP-10:/> set radio/rfu/tx-freq 14515000radio/rfu/tx-freq 14515000 IP-10:/> get radio/rfu/rx-freq

IP-10:/> get radio/rfu/rx-freq 14935000

14935000 IP-10:/> set

IP-10:/> set radio/rfu/rx-freq 14935000radio/rfu/rx-freq 14935000

36. Mute TX 36. Mute TX

IP-10:/> get radio/rfu/mute-tx IP-10:/> get radio/rfu/mute-tx disable

disable IP-10:/> set

IP-10:/> set radio/rfu/mute-txradio/rfu/mute-tx disable enable

disable enable

IP-10:/> set radio/rfu/mute-tx enable IP-10:/> set radio/rfu/mute-tx enable 37. Check TX/RX LEVEL

37. Check TX/RX LEVEL IP-10:/> get

IP-10:/> get radio/rfu/tx-level-radio/rfu/tx-level-statusstatus 22

22

IP-10:/> get radio/rfu/rx-level IP-10:/> get radio/rfu/rx-level -39

-39

38. Check RFU Serial ,Part No

38. Check RFU Serial ,Part No and Softwareand Software IP-10:/> get

IP-10:/> get radio/rfu/serial-nuradio/rfu/serial-numbermber FC527553

FC527553 IP-10:/> get

IP-10:/> get radio/rfu/part-nradio/rfu/part-numberumber IP-10:/>

IP-10:/> get get radio/rfu/softwarradio/rfu/software-version-nume-version-numberber C1.64_B5

(9)

IP-10

IP-10:/> get

IP-10:/> get radio/rfic/if-loopbaradio/rfic/if-loopbackck↵↵

Off Off

IP-10:/> set radio/rfic/if-loopback IP-10:/> set radio/rfic/if-loopback off on

off on

IP-10:/> set radio/rfic/if-loopback on IP-10:/> set radio/rfic/if-loopback on↵↵

Ip-10 Cli Command Line

CLI COMMAND LINE

CLI COMMAND LINE

Aug 2008

Contents

Contents

1.

1.

Document Purpose

Document Purpose

2.

2.

Document

Document Scope

Scope

3.

3.

Startup

Startup Configuration

Configuration Steps

Steps

Getting Started

Getting Started

MAIN MANU

MAIN MANU

IP-10:/> ls

IP-10:/> ls

Management Command Line

Management Command Line

1.

1. Check

Check the

the IP

IP Address

Address

2.

2. Change

Change the IP

the IP Address

Address

3. Check Subnet Mask

3. Check Subnet Mask