CT00-000.814.36.01.02.pdf

(1)

All documents may only be used for rendering services on Siemens Healthcare Products. Any document in electronic form may be printed once. Copy and distribution of electronic docu-ments and hardcopies is prohibited. Offenders will be liable for damages. All other rights are re-served.

Print No.:

Hardcopy Cameras

Installation and Startup

CT

CT00-000.814.36.01.02 English

Hardcopy Camera Information with SOMARIS/7

VA27

(2)

1Copyright / Version / Disclaimer

Copyright

“© Siemens, 2010“ refers to the copyright of a Siemens entity such as Siemens Aktienge-sellschaft - Germany, Siemens Shenzhen Magnetic Resonance Ltd. - China, Siemens Shanghai Medical Equipment Ltd. - China, Siemens Medical Solutions USA Inc. - USA and/or Siemens Healthcare Diagnostics Inc. - USA.

Document Version

Siemens reserves the right to change its products and services at any time.

In addition, manuals are subject to change without notice. The hardcopy documents corre-spond to the version at the time of system delivery and/or printout. Versions to hardcopy documentation are not automatically distributed. Please contact your local Siemens office to order current version or refer to our website http://www.healthcare.siemens.com.

Disclaimer

Siemens provides this documentation “as is“ without the assumption of any liability under any theory of law.

The installation and service of equipment described herein requires superior understand-ing of our equipment and may only be performed by qualified personnel who are specially trained for such installation and/or service.

(3)

1 _ General Hardcopy Camera Information ________________________ 7

HCC Information for SOMATOM Definition AS . . . 7

General information . . . 7

Scope of applicability . . . 9

Modality. . . 12

Image quality and optical density check . . . 17

General image quality information (LUT) . . . 17

Density verification . . . 17

Reference films . . . 19

Description of Correction LUT Files . . . 20

Additional and unnecessary LUT files . . . 21

2 _ Specific Camera Information - Agfa __________________________ 23

Agfa Drystar AXYS . . . 23

General Information . . . 23

SCU / modality software configuration . . . 24

SCP / hardcopy camera configuration (provided by OEM) . . . 26

Image Quality and Optical Density . . . 29

Agfa Drystar 5503. . . 31

SCU / Modality Software Configuration . . . 32

SCP / Hardcopy Camera Configuration (provided by OEM) . . . 34

Agfa LR5200 / LR DICOM Controller . . . 66

(4)

3 _ Specific Camera Information - Codonics______________________ 74

Codonics Horizon . . . 74

4 _ Specific Camera Information - Fuji___________________________ 81

Fuji Drypix 7000 / 5000 . . . 81

Fuji Drypix 4000 . . . 88

Fuji Drypix 3000 . . . 96

Fuji Drypix 2000 . . . 102

Fuji FM DPL/FN-PS551 . . . 111

5 _ Specific Camera Information - CARESTREAM ________________ 120

CARESTREAM DryView 5850 . . . 120

SCU / modality software configuration. . . 121

Image quality and optical density . . . 126

Kodak DryView 6800. . . 128

(5)

Kodak DryView 8900 (small border) . . . 145

Kodak DryView 8700-Plus / PACS Link MIM 200 . . . 151

Kodak DryView 8200 / PACS Link MIM 200 . . . 158

Kodak DryView 8100 / PACS Link MIM 200 . . . 165

Kodak DryView 8150 . . . 173

6 _ Specific Camera Information - Konica Minolta ________________ 180

KONICA MINOLTA DryPro 873 . . . 180

Konica Minolta DryPro 832. . . 190

(6)

Konica DryPro 751/752 . . . 216

7 _ Specific Camera Information Sony__________________________ 223

SONY UP-DF 750 . . . 223

Sony UP-DF 550 . . . 232

Sony UP-DF 500 . . . 240

(7)

HCC Information for SOMATOM Definition AS

0

General information

0

Acronyms and abbreviations

Block Diagram SOMATOM Definition

Fig. 1:

System references

•

Refer to Siemens Medical Solutions Intranet, UPTIME Services AE Title Application entity title

BU Business Unit (Modality)

DCS DICOM Conformance Statement

DICOM Digital Imaging and Communication in Medicine

HW/SW Hardware/Software

HCC Hardcopy Camera

LAN Local Area Network

LUT Lookup Table

OEM Original Equipment Manufacturer SCP Service Class Provider

SCU Service Class User

(8)

•

Product-specific technical documentation

Hardware components

•

Ethernet switch ATI-FS708 (part no.: 30 79 332)

•

Cable, straight-through, S/UTP RJ45 (5m.; part no.: 30 74 515)

•

Cable, straight-through, S/UTP RJ45 (30 m.; part no.: 30 74 523) or

•

Refer to Siemens Medical Solutions Intranet, UPTIME Services

•

Product-specific technical documentation

Restrictions and known effects

NOTE Sending film sizes that are not available at the customer site may cause problems at the camera site. For this reason, it is recommended that you delete these film sizes for portrait and landscape formats.

NOTE The Grayscale Standard Display Function (GSDF) is imple-mented for printing and imaging. No Presentation LUTs are available. For this reason, the DICOM Presentation LUT is not released.

NOTE The use of the presentation LUT has to be disabled by local service for configuring LUT files.

NOTE The density values for the image quality were measured with a calibrated densitometer X-Rite 301. The result of the mea-surement from other densitometers used may differ from the absolute density values as described in the tables.

NOTE Print the 17 graystep test image to check the modality and camera adjustment according to the description. Verify the results using the reference values for max. density 2.80 listed in the table. This is also part of the acceptance test.

Errors and warning messages

Only certain errors and warnings have been tested for each hardcopy camera. These errors and warnings are described in the corresponding camera information. .

(9)

Scope of applicability

0

Modality/system

Hardcopy Cameras

This table includes all hardcopy cameras using DICOM basic print.

Device type Modality (SCU)

Product name SOMATOM Definition Modality host name/console CT host name

ICS (syngo Acquisition Workplace) IES (syngo CT Workplace; optional) IRS (Image Reconstruction System) Manufacturer Siemens Med CT

(10)

Manufacturer HCC name Software validity VA27 V... V.... V....

AGFA Drystar AXYS X

AGFA Drystar 5503 X

AGFA Drystar 5500 X

AGFA Drystar 5302 X

AGFA Drystar 5300 X

AGFA Drystar 3000 X

AGFA LR5200 / LR DICOM Controller X

CODONICS Horizon X FUJI Drypix 7000/5000 X FUJI Drypix 4000 X FUJI Drypix 3000 X FUJI Drypix 2000 X FUJI FM DPL / FN-PS 551 X CARESTREAM DryView 5850 X CARESTREAM [1] DryView 6800 X CARESTREAM [1] DryView 5800 X

CARESTREAM [1] DryView 8900 (small border) X CARESTREAM [1] DryView 8700-Plus /

PACS Link MIM 200 X

CARESTREAM [1] DryView 8200 /

PACS Link MIM 200 X

CARESTREAM [1] DryView 8150 X

CARESTREAM [1] DryView 8100 /

PACS Link MIM 200 X

KONICA MINOLTA DryPro 873 X

KONICA DryPro 751/752 X

(11)

[1] = formerly Kodak X = hardcopy camera is released N/A = hardcopy camera is not released

NOTE The use of non-released hardcopy cameras in conjunction with BU products is prohibited and does not meet the requirements specified.

DICOM associations

A DICOM association is a network connection between 2 DICOM applications. The asso-ciation is established and released by the SCU and may be aborted by the SCU or SCP. The maximum number of associations for each HCC device is defined in the DCS. The maximum number of associations depends on the configuration and may be extended by increasing the number of gateways connected to the printer device.

In a DICOM network environment, there are two ways to connect a modality (SCU) to an HCC device (SCP).

Case 1: The association will always be opened. Assuming that this behavior applies to all modalities (connected to the same HCC device), the number of modalities has to be equal to or less than the maximum number of supported associations.

Case 2: The association will be opened (and closed) on demand. Assuming that this behavior applies to all modalities (connected to the same HCC device), the number of modalities may be greater than the maximum number of supported associations. This num-ber will be shared by the modalities.

The association open-close behavior is unknown to other non-SIEMENS modalities. Under optimum circumstances, the number of modalities is equal to or less than the maximum number of supported associations.

The association is always opened by the SCU (case 1)

If the associations are always opened by the SCU for each configured HCC device, the association is reserved for this SCU only.

If the maximum number of associations = 1, and another modality never releases the asso-ciation, this HCC device is always reserved for this modality.

SONY UP-DF550 X

SONY UP-DF500 X

Manufacturer HCC name Software validity VA27 V... V.... V....

(12)

The association is opened and closed on demand (case 2)

The associations will be opened (and closed) on demand by the SCU for each configured HCC device via the product name.

Special cases (compare also to case 1):

If the number of modalities configured in the HCC device is greater than the maximum num-ber of supported associations, some modalities will not be able to print. The printing func-tion depends on the access time and release mechanism of each connected modality (e.g., the maximum number of supported associations = 1, the number of modalities = 2. During access by the first modality, access by the second modality is denied and connectivity fails, and vice versa).

If other modalities do not release the associations, the shareable number of associations decreases.

Modality

0

Hardware and software prerequisites

All hardware and software prerequisites are included in the <modality> product delivery volume.

Parameters

For software configuration, HCC data/parameters and possibly additional film matrix prop-erties (syngo: filming propprop-erties) are required for software configuration.

Modality data and configuration parameters

HCC Data and Configuration Parameters1

1 The values for these parameters are part of the specific HCC information Example: Kodak DryView 8300

Properties Example Supplier

Port number 104 Default entry

AE title PR_”Hostname” Default entry

TCP/IP address xxx.x.x.xxx Network administrator

Application Entity

Properties Display Supplier

AE Title

K8300 Network administrator or HCC service

(13)

Film matrix properties

The settings for filming properties depend on the class selected (DICOM camera). A pull-down menu is provided for DICOM-class cameras. Select your DICOM camera type. A specific file for this type is loaded and the "filming properties" are shown. Changing the "filming properties" will affect the camera site and may not meet the requirements. Do not make any changes, unless otherwise instructed.

NOTE Filming properties are "pixel size" and "media sheet size"; this information is required for image scaling and cannot be changed.

Software configuration

•

The following information is required: - Host Name

HC Device /

General settings Display Supplier

Type DICOM printer Default entry

Class (printer spec file

name) kodak8300 Default entry

DICOM Node dv8300 Default entry

Filming properties Display Supplier

Hold printed Film Jobs 10 Default entry

Min. density 20 Default entry

Pixel Size [1/1000 mm] 85.0 x 85.0 Default entry

Film Sheet Formats, Portrait

Number of Pixels [columns x rows]

8" x 10"

2256 x 2676 Default entry Film Sheet Formats,

Landscape

Number of Pixels [columns x rows]

8" x 10"

2736 x 2136 Default entry

Medium type Blue film Default entry

Film destination Processor Default entry

Color appearance Grayscale 8 bit Default entry

Background Black Default entry

(14)

- TCP/IP address - Application entity title

- Port number of the DICOM remote host (DICOM laser camera)

The AE title, port number and camera type have to be provided by the local camera service.

syngo software configuration and laser camera

1. Select options in the menu line 2. Navigate to local service

¹ The Siemens Service Software Authentication platform is displayed 3. Enter the password and click ”OK”

¹ The Home Menu Platform of the syngo Service Software is displayed 4. Click ”Configuration”

¹ The Local Service Configuration List of system options is displayed 5. Click DICOM ”General”

6. Click ”>”

¹ The local Application Entity Title platform is displayed

7. Provide the Local Camera Service with the information in the field ”Print (SCU) AE Title PR_”Hostname”

8. Click ”Save”; ”>”; ”Finish”

¹ The Configuration Setup platform is displayed 9. Click Local Host ”TCP/IP LAN”

¹ The local Service Configuration TCP/IP LAN platform is displayed

10. Provide the Local Camera Service with the information in the ”IP address” field (scroll down menu for IP address but do not select it)

11. Click ”Finish”

¹ The Configuration Setup platform is displayed 12. Select DICOM Print Devices

¹ The Local Service Hardcopy Device platform is displayed

13. Enter the host name and TCP/IP address of the laser camera (provided by the camera manufacturer)

14. Click ”Test” to test IP communication (ping) 15. Click ”Save”

¹ Host properties successfully saved 16. Click ”OK”

17. Click ”>”

¹ The General Note Properties Dialog platform is displayed 18. Under logical name: Enter the logical name of the laser camera

(15)

19. Select the host and choose the previously defined host name in the hardcopy device platform

20. Under application entity properties: Enter the AE title in the edit AE title field (provided by the camera manufacturer)

21. Enter the Port Number (provided by the camera manufacturer) 22. Click ”Add”

23. Click ”Save”

¹ DICOM node properties successfully saved 24. Click ”OK”

25. Select the logical name again and click ”Verification” to test the DICOM communication (mc3echo)

26. Click ">"

¹ The camera-specific parameter platform is displayed. 27. HC device: Enter the camera name

28. General settings: /type: DICOM printer

29. /class: e.g., agfadrystar3000, or refer to specific HCC information 30. Filming properties:

- Hold printed film job, 10 = default; (max. = 10) (films can be printed again) - Min. density 20 = default; (can be changed in increments of 1)

- Pixel size (changes not allowed)

- Film Sheet Formats Portrait (do not modify and/or add film sizes, select and delete film sizes that are not available at the customer site)

- Medium type, blue film = default; clear film; paper - Film destination, processor = default; magazine

- Color appearance, monochrome = default; (select color for printers that support and use color media only, e.g., Drystar2000; Codonics)

- Background, black =default; white

- Transformation no magnification = default;

do not change this value; except for Kodak DV8900; replicate; (do not change any other values under filming properties) 31. Click "Save"

¹ Caution: Please wait for the message "device properties successfully saved" 32. Click ”OK”

33. Click ”Finish”

¹ The Configuration Setup platform is displayed

34. Click ”>” to proceed and select the next marked DICOM ”HC Overview” 35. Click ”Finish”

¹ The Configuration Setup platform is displayed 36. Click LUT files

(16)

NOTE If new LUT files for one or more modalities are available on a removable medium, e.g., floppy or CD, these files can be selected on the source drive and copied to the dependent LUT directories on the local host. Unnecessary LUT files can be removed from the LUT directories on the local host.

37. Click ">"

¹ Usage of Presentation LUT platform is displayed 38. Select disable

39. Modifications are necessary for additional image impressions only.

NOTE Only the topic CT image and SC image are relevant. Depend-ing on the camera, specific entries have to be made. If noth-ing else is mentioned, set the CT image and SC image to "CTLUT" and "2.80" for maximum density. The entries for BU image and SC image have to be identical.

40. Overall maximum density:

- 3.00 = default (depends on the max. possible value of the max. density of all image types)

41. Interpolation for printing:

- Bilinear mode = default; #Smoothing Type - Replicate #Smoothing Type

- Cubic 0, 2, 3, 4 = concerns cubic mode only 42. When changes are made, click "Save"

43. Click "Finish"

44. Click "Home"; the system automatically restarts the application

(17)

Image quality and optical density check

1.1

General image quality information (LUT)

0

Only standard LUT files are loaded. For importing/removing additional/unnecessary LUT files (see section ”Additional/unnecessary LUT files”) (LINK).

The image data from the modality to the HCC is transformed/corrected by the LUTs, once in the modality and once in the HCC. As as result, the LUT has to be set on both sides:

•

Refer to the Siemens Medical Solutions Intranet, UPTIME Services

•

Product-Specific Technical Documentation

Correction LUT is selected

Density verification

0

There are two ways to check the LUT via the film density:

The modality is configured to a specific correction LUT and the HCC is configured to linear curves. As an alternative, the modality is configured to a linear LUT and the HCC is config-ured to linear curves.

Modality Image Type Correction LUT Max. density

CT Image CT LUT 2.80

SC Image CT LUT 2.80

HCC Refer to the specific Camera Information "DICOM printer settings".

(18)

Density verification for CT

Since these two checks are equivalent; it is sufficient to check the “specified density”. Checking the “HCC linearity” may be necessary if the desired density verification (1) shows deviations and the HCC setting needs to be changed.

NOTE Even if the HCC service does not require a test image of the modality for the HCC setting, it is easier to check this setting - and possibly further HCC corrections - with the HCC linear-ity verification (2) than with the desired denslinear-ity verification (1). Only the HCC linearity LUT is effective. A graphical dis-play would now show the current HCC behavior only. This could be helpful for HCC Service.

Density values for CT

•

Measure the density values in 17 gray levels in the IEC test image (Fig. 2 / p. 18) (for each film size).

W:256; C:0;

Fig. 2: Test image

Check no.

Verification for Modality adjustment

Reference value CT

Application Image Type

Correction LUT

Max. Density

1

Desired density CT Image CT LUT 2.80 Refer to the

table for CTLUT

2

HCC linearity CT Image Linear 2.80 Refer to the

table for lin-ear LUT

(19)

The density difference of the BU LUT (Ref. LUT) between steps 1, 2, and 3 has to be a minimum density value of 0.02. Test image 3 (SMPTE image) can be used for visual veri-fication (the 95% gray square has to be visible).

Reference films

0

Reference film

To create a reference film with the desired LUT adjustment, proceed as follows: 1. The layout is configurable under Option/Configuration/Filming layout

2. Use format 3.2; default center/width, for the film sheet

Step

CT LUT Linear LUT

Ref. LUT Maximum Density

Minimum

Density Ref. LUT

Maximum density Minimum density 1 0.20 0.23 0.17 0.20 0.23 0.17 2 0.23 0.26 0.20 0.36 0.40 0.33 3 0.28 0.32 0.24 0.53 0.56 0.49 4 0.35 0.39 0.31 0.69 0.73 0.64 5 0.43 0.48 0.38 0.85 0.90 0.80 6 0.52 0.57 0.47 1.01 1.06 0.96 7 0.63 0.69 0.57 1.18 1.23 1.12 8 0.75 0.81 0.69 1.34 1.40 1.28 9 0.88 0.95 0.82 1.50 1.57 1.44 10 1.04 1.11 0.97 1.66 1.73 1.59 11 1.21 1.28 1.14 1.83 1.90 1.75 12 1.41 1.49 1.33 1.90 2.07 1.91 13 1.64 1.72 1.56 2.15 2.23 2.07 14 1.88 1.97 1.79 2.31 2.40 2.23 15 2.13 2.22 2.04 2.48 2.57 2.38 16 2.44 2.54 2.34 2.64 2.73 2.54 17 2.80 2.90 2.70 2.80 2.90 2.70

(20)

3. Select the "Viewing" tab, select Patient Browser, navigate to the folder "CT Reference Images" and view the test images:

Use test images (technical images) without text and the three CT Medical Ref images (cerebrum, pancreas, (LWS) lumbar spine) with text and print the film sheet. (the DICOM command to the printer is always "magnification none")

4. Measure IEC test image 1 (Fig. 2 / p. 18) and verify the CTLUT using the table "Density values for modality CT”

Segment layout:

5. Repeat this procedure with the linear LUT adjustment

6. If the reference images are not available, please load the reference images from H:\SITE_DATA\Reference-images\* in the storage device (import from offline)

Description of Correction LUT Files

0

Description of Correction LUT Files for CT

1 2

3 4

5 6

Segment Image Window Center

1 IEC test image 1 (17 gray levels) 256 0

2 IEC test image 2 (50% gray field) 256 0

3 Test image 3 (SMPTE test pattern) 100 0

4 Pancreas (Abdomen) 520 104

5 Cerebrum (Head) 80 53

6 LWS (Spine) 440 56

Correction LUT LUT files with D_min. 0.2 and D_max. 2.80

Linear Linear LUT

CT LUT Standard LUT; default for all cameras; adapts D_min. of 0.2 CT02 vs. CT LUT Dark area = less contrast; darker; softer; white area = more

con-trast

CT03 vs. CT02 Dark area = less contrast; darker; softer; white area = more con-trast

CT04 vs. CT LUT Dark area = more contrast; darker; sharper; white area: no changes

(21)

Additional and unnecessary LUT files

0

If new, released LUT files are available on a removable medium (e.g., floppy or CD). These files may be selected on the source drive and copied to the dependent LUT directories on the local system. Unnecessary LUT files may be removed from LUT directories on the local system.

Importing LUT files

1. In Local Service Configuration platform, select LUT files

2. Select the (source) drive and the path where the appropriate LUT files are located 3. Select the destination LUT directory (correction LUT directory) which depends on the

image type (CTImage).

4. By pushing the copy button, the selected LUT file will be transferred to CTImage type. 5. Repeat this procedure using the appropriate LUT files for SC Images.

6. Select the destination LUT directory (correction LUT directory) which depends on the image type (SCImage).

7. Pushing the copy button transfers the selected LUT file to SCImage type. 8. Confirm the message "Files successfully copied" by clicking "OK"

Removing LUT files

Unnecessary LUT files can be removed from LUT directories on the local host by selecting the appropriate LUT file and clicking the "Remove" button.

•

Click ">"

CT05 vs. CT LUT Brighter; no changes in contrast for large window width; more contrast for head images (small window width)

CT06 vs. CT LUT Brighter than CT5; white area = less contrast cthead1 LUT for head images, images smoother cthead2 vs. cthead1 Images smoother

CT015 Adapts Dmin of 0.15 (for cameras which are not supported Dmin. command)

CT017 Adapts Dmin. of 0.17 (for cameras which are not supported Dmin. command)

CT LUTdry LUT for dry cameras; adapts Dmin. of 0.22 (5% visible in SMPTE test pattern)

CT Lung LUT for lung images

(22)

Real Size Scaling

This procedure should be performed after system installation and when the Hardcopy Camera is ready to print. The real size behavior has to be performed with each connected Hardcopy Camera.

Real size scaling verification

1. Load the test image (water image phantom) into the viewer (e.g. 20 cm water phantom, generated with the constancy procedure by CT).

2. Insert Crosshair (Viewing Card: Tools) and copy the image to the film sheet (“copy image to film sheet” button).

3. Select film sheet format 1 X 1.

4. Select "Original Image" in the filming card and print the image.

5. Use a calibrated ruler to measure the crosshairs of the printed image.

¹ The results should correspond to the printed value underneath the scale with a tolerance of ±1% in both directions.

(23)

Agfa Drystar AXYS

0

General Information

0

Block Diagram

Fig. 3:

Available Film Sizes

Performance and Connections

Associations

Maximum number of associations supported: 10

Format Release status Film type Medium type

14" x 17"

Portrait Yes DT2B Blue-based

Landscape Yes DT2B Blue-based

14" x 14"

11" x 14"

10” x 12”

8" x 10"

Other n.a. n.a. n.a.

Released: Yes - Film size is available and released Released: No - Film size is available but not released Released: n.a. - Film size is not available

(24)

Performance

Use medical image 4 of patient "Reference Images", maximum film size, positive image, 4x5 format, Copies=1, default center/width, magnification type none.

The optimum connection (point to point) was used.

Restrictions

NOTE For HCC-independent restrictions, refer to (Restrictions and known effects / p. 8).

NOTE Slight inhomogeneity visible in gray field

NOTE Typical slight line structure of the thermo head is visible in technical image.

NOTE Two edges of the diagnostic area are cut (approx 1 mm) for 8x10, 10x12, 11x14,14x17.

NOTE The background command does not work properly. The back-ground is always white.

Known effects

NOTE European EMC Classification is Class A.

NOTE The built in densitometer has to be set to X-Rite 301x to achieve the required image quality.

SCU / modality software configuration

0

Time 74 sec

Properties Display Changes allowed

AE Title AXYS Yes

(25)

HC Device /

General settings Display Changes allowed

Type DICOMprinter No

Class

(Printer spec file name)

agfadrystar5503_AX

YS No

DICOM Node DSAXYS Yes

Filming properties Display Changes allowed

Hold printed film jobs 10 Yes

Min. density 20 Yes

Pixel Size [1/1000 mm] 50.0 x 50.0 No

Film sheet formats, Portrait Number of pixels [columns x rows] 14" x 17" 6922 x 8368 14" x 14" 6882 x 6882 11" x 14" 5376 x 6922 10" x 12" 4880 x 5860 8" x 10" 3852 x 4880 In “define new” Do not modify/add Select only Delete only Film sheet formats,

Landscape Number of pixels [columns x rows] 14" x 17" 8368 x 6922 14" x 14" 6882 x 6882 11" x 14" 6922 x 5376 10" x 12" 5860 x 4880 8" x 10" 4880 x 3852

Medium type Blue film Yes

Film destination Processor No

(26)

NOTE Do not modify or add film sizes. Do not modify pixel sizes.

Delete film sizes not available at the customer site.

SCP / hardcopy camera configuration (provided by OEM)

0

Identification

Printer Settings

Background Black Yes

Transformation No magnification No

Device type: DICOM printer

Device name: DRYSTAR AXYS

Manufacturer: AGFA

SW Revision: R 1.60C1

Physical interface: Ethernet 10/100 Base-Tx

Network protocol: TCP/IP DICOM

DICOM conformance statement: Document No.: 001150 Revision 1.0

Image memory: 65 GByte

Hard disk: 70 GByte

Selected Variable name Setting

n.a. Nickname CT hostname

n.a. Use this profile only for incoming call-ing AE Title

PR_hostname

n.a. Use this profile only for local SCP server

DEFAULT_SCP

n.a. Host profile type GENERIC-GENERIC (customized)

No Number of Copies 1

No Print priority Low

(27)

No Film orientation Portrait

No Trim No

No Film Size ID (empty)

No Medium type (empty)

n.a. Print even if Film Size ID / Medium Type is not supported

No

n.a. Print even if Application Type is not supported

No

No Initial memory size allocated per print job (Mbytes):

100

No Kernel Site, Edit Custom:

Interpolation type;

Cubic high res. -smoothing factor -0.7

No Magnification Magn. none

No Decimate/Crop behavior: Disabled

No Pixel Size ratio 1.0 / 1.0

No Perception LUT Linear

n.a. Kanamori-like value 0

n.a. Custom Value empty

No Illumination (cd/m) 2000

No Reflected ambient light (cd/m2) 10

No Border density (OD x 100) Black

No Empty image density (OD x 100) Black

No Minimum density empty

No Maximum density Site 320

n.a. Header annotation Contents: Edit custom:

None Courier 12

n.a. Footer annotation Contents: Edit custom:

None Courier 12

n.a. Window (%) Empty

n.a. Level (%) Empty

(28)

Error / warning messages (examples)

n.a. Image orientation r0

n.a. Conformance level 1

n.a. N-event enabled Off

n.a. Mammo modality site No

n.a. Association time-out(s) 0

n.a. Image time-out(s) 0

n.a. ALLOW IMPLICIT VR LITTLE ENDIAN

Selected

n.a. ALLOW EXPLICIT VR LITTLE ENDIAN

Selected

n.a. ALLOW EXPLICIT BIG ENDIAN Selected

n.a. Resolution 508

n.a. Supported SOP classes Presentation LUT SOP class Print job SOP class

Printer SOP class

Basic annotation box SOP class Verification service class

Basic film box SOP class Basic film session SOP class Basic color PM Meta SOP class Print Queue Management SOP INSTANCE

Basic Grey Image Box SOP Class Basic color image box SOP class Basic gray PM Meta SOP class Print queue management SOP class

n.a. LR like off

Camera warning or error messages

Printer message Message displayed on SCU (*2)

Defined DCS (*1) Sent by SCP

Top cover open COVER OPEN COVER OPEN Camera cover,

drawer or door open Tray open or front

door open

BAD SUPPLY MGZ BADSUPPLY MGZ Problem with supply magazine

(29)

Image Quality and Optical Density

0

No specific parameter available

Real Size Scaling

Send print job to camera if the camera is in service mode

PRINTER OFFLINE PRINTER OFFLINE Camera offline

Sent print job to cam-era with empty input tray

SUPPLY EMPTY SUPPLY EMPTY Camera out of film

(*1) refer to all messages in the DCS of the hardcopy camera (*2) refer to all messages in the DCS of the modality

Camera warning or error messages

Film size / Direction Desired (mm) Measured (mm) Deviation obtained from desired value in % 14" x 17" Portrait X 330.0 330.0 0.00 Y 390.0 391.0 0.26 14" x 17" Landscape X 410.0 411.0 0.24 Y 320.0 320.0 0.00 14" x 14" Portrait X 330.0 331.0 0.30 Y 320.0 320.0 0.00 14" x 14" Landscape X 330.0 330.0 0.00 Y 330.0 331.0 0.30 11" x 14" Portrait X 260.0 261.0 0.38 Y 330.0 330.5 0.15 11" x 14" Landscape X 330.0 330.0 0.00 Y 250.0 251.0 0.40 10” x 12” Portrait X 230.0 230.0 0.00 Y 270.0 271.0 0.37

(30)

10” x 12” Landscape X 280.0 280.5 0.18 Y 220.0 220.0 0.00 8" x 10" Portrait X 180.0 180.0 0.00 Y 220.0 220.0 0.00 8" x 10" Landscape X 230.0 230.0 0.00 Y 170.0 170.0 0.00

Film size / Direction Desired (mm) Measured (mm)

Deviation obtained from

desired value in %

(31)

Agfa Drystar 5503

2.1

General information

0

Block diagram

Fig. 4:

Available film sizes

Associations

Format Release status Film Type Medium type

14" x 17"

14" x 14"

11" x 14"

10” x 12”

8" x 10"

(32)

Performance

Use medical image 4 of patient "Reference Images", maximum film size, positive image, format 4x5, Copies=1, default center/width, magnification type none.

The optimal connection (point to point) was used.

Restrictions

NOTE All four edges of the diagnostic area are cut (approx 1 mm) for 8x10, 10x12, 11x14,14x17.

NOTE Typical line structure of the thermo head is visible.

Known effects

NOTE European EMC Classification is Class A.

SCU / Modality Software Configuration

0

Time 70 sec

AE Title DRY5503 Yes

(33)

HC Device /

Class

(Printer spec file name)

agfadrystar5503_AX

YS No

DICOM Node DRY5503 Yes

Hold printed Film Jobs 10 Yes

Min. density 20 Yes

Pixel Size [1/1000 mm] 50.0 x 50.0 No

Film Sheet Formats, Portrait Number of Pixels [columns x rows] 14" x 17" 6922 x 8368 14" x 14" 6882 x 6882 11" x 14" 5376 x 6922 10" x 12" 4880 x 5860 8" x 10" 3852 x 4880 In “define new” Do not modify/add Select only Delete only Film Sheet Formats,

Landscape Number of Pixels [columns x rows] 14" x 17" 8368 x 6922 14" x 14" 6882 x 6882 11" x 14" 6922 x 5376 10" x 12" 5860 x 4880 8" x 10" 4880 x 3852

(34)

NOTE Do not modify and/or add film sizes. Do not modify pixel sizes.

SCP / Hardcopy Camera Configuration (provided by OEM)

0

Identification

Printer settings

Device name: DRYSTAR 5503

Manufacturer: AGFA

SW Revision: R 5.0.0 B2

Physical Interface: Ethernet 10/100 Base-Tx

Network protocol: TCP/IP DICOM

DICOM Conformance Statement: AGFA Medical Imaging DICOM Conform-ance Statement, DrayStar 5503, SW ver-sion 5.0

Image memory: 2 * 256 Mbyte (RAM memory)

Hard disk: min. 18 Gbyte

PR_hostname

DEFAULT_SCP

(35)

No Polarity Normal No Film destination output tray n.a.

n.a. Tray 1 Selected

n.a. Tray 2 Deselected

No Trim No

No Medium type “empty”

No

No Initially allocated memory size per print job (Mbytes):

100

Interpolation type;

n.a. Custom Value “empty”

No Minimum density “empty”

None Courier 12

(36)

n.a. Footer annotation Contents: Edit custom: None

Courier 12

n.a. Window (%) “empty”

n.a. Level (%) “empty”

n.a. Mammo modality site, No

Selected

n.a. Resolution 508

n.a. Supported abstract syntax Presentation LUT SOP class Print job SOP class

Printer SOP class

Basic Grey Image Box SOP Class Basic Color Image Box SOP Class Basic gray PM Meta SOP class Print queue management SOP class

n.a. Early processing allowed Yes

n.a. LR like off

(37)

Error / Warning Messages (examples)

Image Quality and Optical Density

0

Real Size Scaling Camera warning or error messages

Open front door COVER OPEN COVER OPEN Camera cover, drawer or door open Tray open or front

door open

Camera is warming up

PRINTER INIT PRINTER INIT Camera initializing

Film size / Direction Desired (mm) Measured (mm) Deviation obtained from desired value in % 14" x 17" Portrait X 330.0 330.0 0.00 Y 390.0 389.5 0.13 14" x 17" Landscape X 410.0 409.5 0.12 Y 330.0 330.0 0.00 14" x 14" Portrait X 330.0 330.0 0.00 Y 320.0 319.5 0.16 14" x 14" Landscape X 330.0 329.5 0.15 Y 330.0 330.0 0.00 11" x 14" Portrait X 250.0 250.0 0.00 Y 320.0 320.0 0.00 11" x 14" Landscape X 330.0 330.0 0.00 Y 250.0 250.0 0.00

(38)

10” x 12” Portrait X 230.0 230.0 0.00 Y 270.0 270.0 0.00 10” x 12” Landscape X 280.0 280.0 0.00 Y 230.0 230.0 0.00 8" x 10" Portrait X 180.0 180.0 0.00 Y 230.0 230.0 0.00 8" x 10" Landscape X 230.0 230.0 0.00 Y 170.0 170.0 0.00

(39)

Agfa Drystar 5500

2.2

General Information

0

Block Diagram

Fig. 5:

Available Film Sizes

Associations

14" x 17"

14" x 14"

11" x 14"

10” x 12”

8" x 10"

(40)

Performance

Use medical image 4 of patient "Reference Images", maximum film size, positive image, 4x5 format, Copies=1, default center/width, magnification type none.

The optimum connection (point to point) was used.

Restrictions

NOTE All four edges of the diagnostic area are cut (approx 1 mm) for 8x10, 10x12, 11x14,14x17.

NOTE Typical line structure of the thermo head is visible.

Known effects

SCU / Modality Software Configuration

0

Time 69 sec

Port number 104 No

HC Device /

(41)

Class

(Printer spec file name) agfadrystar5500 No

DICOM Node DRY5500 Yes

Min. density 20 Yes

Pixel Size [1/1000 mm] 50.0 x 50.0 No

Film sheet formats, Portrait Number of pixels [columns x rows] 14" x 17" 6922 x 8368 14" x 14" 6882 x 6882 11" x 14" 5376 x 6922 10" x 12" 4880 x 5860 8" x 10" 3852 x 4880 In “define new” Do not modify/add Select only Delete only Film sheet formats,

Landscape Number of pixels [columns x rows] 14" x 17" 8368 x 6922 14" x 14" 6882 x 6882 11" x 14" 6922 x 5376 10" x 12" 5860 x 4880s 8" x 10" 4880 x 3852

Color appearance Gray scale 8 bit No

HC Device /

(42)

SCP / Hardcopy Camera Configuration (provided by OEM)

0

Identification

Printer Settings

Manufacturer: AGFA

SW Revision: V3.0.0 C1

Physical interface: Ethernet (RJ45)

Network protocol: TCP/IP

DICOM conformance statement: AGFA Medical Imaging DICOM Conform-ance Statement, DrayStar 5500, Document No.: 737

Image memory: 2 * 256 Mbyte

Hard disk: 18 GByte

PR_hostname

DEFAULT_SCP

No Polarity Normal

No Film destination output tray n.a.

n.a. Tray 1 Selected

(43)

No Trim No

No Medium type (empty)

No

No Initial memory size allocated per print job (Mbytes):

100

Interpolation type;

n.a. Custom Value “empty”

No Minimum density “empty”

None Courier 12

(44)

n.a. Mammo modality site, No

Selected

n.a. Resolution 508

Printer SOP class

Basic Grey Image Box SOP Class Basic Color Image Box SOP Class Basic gray PM Meta SOP class Print queue management SOP class

n.a. Early processing allowed Yes

n.a. LR like off

(45)

Image Quality and Optical Density

0

Real Size Scaling Camera warning or error messages

Sent print job to cam-era with front door open

COVER OPEN COVER OPEN Camera cover,

drawer or door open

Tray open or front door open

Printer warming up PRINTER INIT PRINTER INIT Camera initializing (*1) refer to all messages in the DCS of the hardcopy camera

(*2) refer to all messages in the DCS of the modality

Film size / Direction Desired (mm) Measured (mm) Deviation obtained from desired value in % 14" x 17" Portrait X 330.0 330.0 0.00 Y 400.0 399.0 0.25 14" x 17" Landscape X 410.0 409.0 0.24 Y 330.0 330.0 0.00 14" x 14" Portrait X 330.0 329.5 0.15 Y 330.0 330.0 0.00 14" x 14" Landscape X 330.0 330.0 0.00 Y 330.0 329.5 0.15 11" x 14" Portrait X 250.0 249.5 0.20 Y 330.0 330.0 0.00 11" x 14" Landscape X 330.0 330.0 0.00 Y 250.0 249.5 0.00

(46)

10” x 12” Portrait X 230.0 230.0 0.00 Y 270.0 269.5 0.19 10” x 12” Landscape X 280.0 279.5 0.18 Y 230.0 230.0 0.00 8" x 10" Portrait X 180.0 179.5 0.28 Y 230.0 230.0 0.00 8" x 10" Landscape X 230.0 230.0 0.00 Y 170.0 169.5 0.29

(47)

Agfa Drystar 5302

2.3

General information

0

Block diagram

Fig. 6:

Associations

14" x 17"

14" x 14"

11" x 14"

10” x 12”

8" x 10"

(48)

Performance

Restrictions

NOTE If the film size was not included in the configuration of the camera, the connection to the camera is not available.

Known effects

SCU / Modality Software Configuration

0

Time 67 sec

Port number 104 No

HC Device /

Class

(Printer spec. file name) agfadrystar5302 No

(49)

Delete film sizes that are not available at the customer site. Filming properties Display Changes allowed

Min. density 20 Yes

Pixel Size [1/1000 mm] 79.375 x 79.375 No

Film Sheet Formats, Portrait Number of Pixels [columns x rows] 14" x 17" 4358 x 5232 14" x 14" 4358 x 4303 11" x 14" 3348 x 4358 10” x 12” 3070 x 3653 8" x 10" 2376 x 3070 In “Define new” Do not modify/add Select only Delete only Film Sheet Formats,

Landscape Number of Pixels [columns x rows] 14" x 17" 5232 x 4358 14" x 14" 4303 x 4358 11" x 14" 4358 x 3348 10” x 12” 3653 x 3070 8" x 10" 3070 x 2376

Color appearance Gray scale 8 bit No

(50)

SCP / Hardcopy Camera Configuration (provided by OEM)

0

Identification

Manufacturer: AGFA

SW Revision: V1.80 c1

Physical Interface: Ethernet (RJ45)

DICOM Conformance Statement: Revision 1.1, June 2005

Image memory: 512 Mbyte (internal memory)

Hard disk: 35 GB

n.a. Use this profile only for incoming "Calling AE Title":

PR_hostname

n.a. Use this profile only for local SCP server DEFAULT_SCP

n.a. Host Profile Type GENERIC-GENERIC

(custom-ized)

No Polarity Normal

No Trim No

No Film Size ID Deselected

No Medium type Deselected

No

n.a. Print even if Application Type is not sup-ported:

No

No Initial allocated memory size per print job (Mbytes):

(51)

No Kernel SITE (*) Edit Custom:

Interpolation type: Cubic high res. -smoothing factor -0.7

No Magnification Magn: Max. - custom scale

fac-tor 1.0

No Pixel Size Ratio: 1.0 / 1.0

n.a. Custom Value Deselected

No Illumination (cd/m2) 2000

No Minimum density Empty

None Courier 12

n.a. Image orientation R0

n.a. Conformance level 1

n.a. Mammo modality Site, No.

n.a. ALLOW IMPLICIT VR LITTLE ENDIAN Selected n.a. ALLOW EXPLICIT VR LITTLE ENDIAN Selected

(52)

n.a. Resolution 320

n.a. Supported SOP classes: Edit

Printer SOP class

Basic annotation box SOP class

Verification service class Basic film box SOP class Basic film session SOP class Basic color PM Meta SOP class

Print Queue Management SOP INSTANCE

Basic Grey Image Box SOP Class

Basic Color Image Box SOP Class

Basic gray PM Meta SOP class Print queue management SOP class

n.a. LR-like Off

Action that results in camera error mes-sages Printer messages Message displayed on SCU Defined DCS (*1) Sent by SCP (*2)

Top cover open COVER OPEN COVER OPEN Camera cover, drawer or door open

Open film supply tray BAD SUPPLY MGZ

BAD SUPPLY MGZ

Problem with supply magazine

Empty input tray SUPPLY EMPTY SUPPLY EMPTY Camera out of film

Sent wrong film size n.a. n.a. Status -> aborted

(53)

NOTE If film size is not inserted in configuration of camera, connec-tion to camera is not available.

Image Quality and Optical Density

0

No specific parameter available.

Real size scaling

Film size / Direction Desired (mm) Measured (mm) Deviation obtained from desired value in % 14" x 17" Portrait X 330.0 330.0 0.00 Y 390.0 391.0 0.26 14" x 17" Landscape X 410.0 411.0 0.24 Y 330.0 330.0 0.00 14" x 14" Portrait X 330.0 331.0 0.30 Y 330.0 330.0 0.00 14" x 14" Landscape X 330.0 330.0 0.00 Y 330.0 331.0 0.30 11" x 14" Portrait X 250.0 250.5 0.20 Y 330.0 330.0 0.00 11" x 14" Landscape X 330.0 330.0 0.00 Y 250.0 251.0 0.40 10” x 12” Portrait X 230.0 230.0 0.00 Y 270.0 271.0 0.37 10” x 12” Landscape X 280.0 281.0 0.36 Y 230.0 230.0 0.00 8" x 10" Portrait X 170.0 170.5 0.29 Y 230.0 230.0 0.00 8" x 10" Landscape X 230.0 230.0 0.00 Y 170.0 170.0 0.00

(54)

Agfa Drystar 5300

2.4

General information

0

Block diagram

Fig. 7:

Associations

Format Release status Film Type Medium type

14" x 17"

14" x 14"

Portrait n.a. N/A n.a.

Landscape n.a. N/A n.a.

11" x 14"

10” x 12”

8" x 10"

Other n.a. N/A n.a.

(55)

Performance

Restrictions

Known effects

SCU / Modality Software Configuration

0

Time 67 sec

Port number 104 No

HC Device /

Class

(Printer spec file name) agfadrystar5300 No

DICOM Node DS5300 Yes

Hold printed Film Jobs 10 Yes

(56)

SCP / Hardcopy Camera Configuration (provided by OEM)

0

Identification

Pixel Size [1/1000 mm] 79.375 x 79.375 No

Film Sheet Formats, Portrait Number of Pixels [columns x rows] 14" x 17" 4256 x 5174 11" x 14" 3300 x 4256 In “define new” Do not modify/add Select only Delete only Film Sheet Formats,

Landscape Number of Pixels [columns x rows] 14" x 17" 5174 x 4256 11" x 14" 4256 x 3300

Color appearance Grayscale 8 bit No

Device type: DICOM print server/printer

Manufacturer: AGFA

SW Revision: 1.82 C1

Physical Interface: 10/100 Base - T

DICOM Conformance Statement: Rev.1.2, October 24, 2005

Image memory: 512 Mbyte

(57)

n.a. Use this profile only for incoming “Calling AE title”

PR_hostname

All

n.a. Host Profile Type GENERIC-GENERIC (customized)

No Polarity Normal

No Trim No

No Film Size ID Deselected

No Medium type Deselected

No

No Kernel SITE

Interpolation type: Cubic High Res - Smooth Factor -2.5

No Magnification Magn: Max. - custom scale factor 1.0

No Pixel Size Ratio: 1.0 / 1.0

No Kanamori-like value 0

No Custom Value Deselected

No Minimum density Empty

No. Annotation 1 None

(58)

n.a. Image orientation R0

n.a. Mammo Modality site: No.

Selected

n.a. Resolution 320

n.a. Supported SOP Classes Presentation LUT SOP class Print job SOP class

Printer SOP class

Basic film box SOP class Basic film session SOP class Basic Color PM Meta SOP Class Print Queue Management SOP INSTANCE

Basic Grey Image Box SOP Class Basic Color Image Box SOP Class Basic gray PM Meta SOP class Print queue management SOP class n.a. Initial allocated memory size per print

job (MBytes)

23

CT00-000.814.36.01.02.pdf

Hardcopy Cameras

Installation and Startup

CT

Hardcopy Camera Information with SOMARIS/7

VA27

1 _______ General Hardcopy Camera Information ______________________________ 7

2 _______ Specific Camera Information - Agfa ________________________________ 23

3 _______ Specific Camera Information - Codonics____________________________ 74

4 _______ Specific Camera Information - Fuji_________________________________ 81

5 _______ Specific Camera Information - CARESTREAM ______________________ 120

6 _______ Specific Camera Information - Konica Minolta ______________________ 180

7 _______ Specific Camera Information Sony________________________________ 223

HCC Information for SOMATOM Definition AS

General information

•

•

•

•

•

•

•

Scope of applicability

Modality

•

Image quality and optical density check

General image quality information (LUT)

•

•

Density verification

•

Reference films

Description of Correction LUT Files

Additional and unnecessary LUT files

•

Agfa Drystar AXYS

General Information

SCU / modality software configuration

SCP / hardcopy camera configuration (provided by OEM)

Image Quality and Optical Density

Agfa Drystar 5503

General information

SCU / Modality Software Configuration

SCP / Hardcopy Camera Configuration (provided by OEM)

Image Quality and Optical Density

Agfa Drystar 5500

General Information

SCU / Modality Software Configuration

SCP / Hardcopy Camera Configuration (provided by OEM)

Image Quality and Optical Density

Agfa Drystar 5302

General information

SCU / Modality Software Configuration

SCP / Hardcopy Camera Configuration (provided by OEM)

Image Quality and Optical Density

Agfa Drystar 5300

General information

SCU / Modality Software Configuration

SCP / Hardcopy Camera Configuration (provided by OEM)

1 _ General Hardcopy Camera Information ________________________ 7

2 _ Specific Camera Information - Agfa __________________________ 23

3 _ Specific Camera Information - Codonics______________________ 74

4 _ Specific Camera Information - Fuji___________________________ 81

5 _ Specific Camera Information - CARESTREAM ________________ 120

6 _ Specific Camera Information - Konica Minolta ________________ 180

7 _ Specific Camera Information Sony__________________________ 223