CPS-03-7.3-007 Rev 01 Standard Piping Class Specification

(1)

DIVISION

Engineering Specification

Custom Process System (CPS)

CPS-03-7.3-007

Revision: 01

Date:

Dec 20, 2013

Page:

1 of 45

Title:

STANDARD PIPING CLASSES

Prepared by:

Reviewed by:

Approved by:

Steven Roberts

Oleg Barsky

Greg Dodson

STANDARD PIPING CLASSES

01 Mar 05, 2014

Revised as noted

SR

SB

GD

00 Dec 20, 2013

Initial release

SR

OB

GD

(2)

DIVISION

Engineering Specification

Custom Process System (CPS)

CPS-03-7.3-007

Revision: 01

Date:

Dec 20, 2013

Page:

2 of 45

Title:

STANDARD PIPING CLASSES

Prepared by:

Reviewed by:

Approved by:

Steven Roberts

Oleg Barsky

Greg Dodson

List of Revisions

Revision

Page

Description of Change

01

2 Add Page for List of Revisions

01

Section 3 Line Classes

A

Change corrosion allowance for Class A02 to None (was 1/16” / 1.6mm)

Change corrosion allowance for Class A02N to None (was 1/8” / 3.2mm)

Add Piping Class A02CR Cryogenic Service

01

Section 3 Line Classes

B and D

Change corrosion allowance for Class B02 to None (was 1/16” / 1.6mm)

Change corrosion allowance for Class B02N to None (was 1/8” / 3.2mm)

Add Piping ClassB02CR Cryogenic Service

Updated A01, A01N, B01, B02, B02N, B03, B03N, B04, B04N, B06, B06N, B08, B08N

Change corrosion allowance for Class D02 to None (was 1/16” / 1.6mm)

Change corrosion allowance for Class D02N to None (was 1/8” / 3.2mm)

Add Piping Class D02CR Cryogenic Service

Updated D02, D02N, D03, D03N, D04, D04N, D06, D06N, D08, D08N

01 A01

Revise pipe schedule from Sch 40 to Sch 80 on sizes ½ to 3”

Changes Nipples and Swages from Sch 80 to Sch 160 and Swage from Sch 40 to Sch 80

01 A01N

Revised Gasket on RF Flanged to 1/16” Compressed Fiber from Spiral Wound

01 A02

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” & 3”

Revise Nipples and Swages from 10S and 40S to 80S

01 A02N

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” & 3”

Revise Nipples and Swages from 10S and 40S to 80S

01 A03

Revise pipe schedules from Sch 40 to Sch 80 sizes to 3”

Revise Nipples and Swages from Sch 80 to Sch 160, and from Sch 40 to Sch 80

01 A03N

Revise pipe schedule on 3” from Sch 40 to Sch 80

01 A04

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” & 3”

Revise Nipples and Swages from 10S and 40S to 80S

Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)

01 A04N

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” & 3”

Revise Nipples and Swages from 40S to 80S

01 A06

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” & 3”

Revise Nipples and Swages from 10S and 40S to 80S

01 A06N

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” & 3”

Revise Nipples and Swages from 10S and 40S to 80S

01 A08

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” & 3”

Revise Nipples and Swages from 10S and 40S to 80S

01 A08N

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” & 3”

Revise Nipples and Swages from 10S and 40S to 80S

01 B01

Revise pipe schedule from Sch 40 to Sch 80 on sizes up to 3”

Revise Swage (PE) from Sch 40 to Sch 80

01 B02

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” & 3”

Revise Nipples and Swages from 40S to 80S

Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)

01 B02N

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” & 3”

Revise Nipples and Swages from 10S and 40S to 80S

Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)

01 B03

Revise pipe schedule from Sch 40 to Sch 80 sizes to 1-1/2”

Revise Swage (PE) from Sch 40 to Sch 80

Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)

01 B03N

Revise pipe schedule from Sch 40 to Sch 80 sizes to 1-1/2”

Revise Swage (PE) from Sch 40 to Sch 80

Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)

01 B04

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” & 3”

Revise Nipples and Swages from 10S and 40S to 80S

(3)

DIVISION

Engineering Specification

Custom Process System (CPS)

CPS-03-7.3-007

Revision: 01

Date:

Dec 20, 2013

Page:

3 of 45

Title:

STANDARD PIPING CLASSES

Prepared by:

Reviewed by:

Approved by:

Steven Roberts

Oleg Barsky

Greg Dodson

Revision

Page

Description of Change

01 B04N

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” & 3”

Revise Nipples and Swages from 10S and 40S to 80S

Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)

01 B06

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” thru 8”

Revise Nipples and Swages from 10S and 40S to 80S

01 B06N

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” thru 8”

Revise Nipples and Swages from 10S and 40S to 80S

01 B08

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” thru 8”

Revise Nipples and Swages from 10S and 40S to 80S

01 B08N

Revised pipe schedules from 10S to 80S sized to 1-1/2” and from 10S to 40S for 2” thru 8”

Revise Nipples and Swages from 10S and 40S to 80S

01 D02

Revised pipe schedules from 10S to 80S sizes to 1-1/2” from 10S to 80S size 2” from - to Sch

80 sizes 10” thru 24”

Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)

01 D02N

Revised pipe schedules from 10S to 80S sizes to 1-1/2” from 10S to 80S size 2” from - to Sch

80 sizes 10” thru 24”

Revise Nipples and Swages from Sch 10S and 40S to 80S

Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)

01 D03

Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)

01 D03N

Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)

01 D04

Revised pipe schedules from 10S to 80S sizes to 1-1/2” from 10S to 80S size 2” from - to Sch

80 sizes 10” thru 24”

Revise Nipples and Swages from Sch 10S and 40S to 80S

Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)

01 D04N

Revised pipe schedules from 10S to 80S sizes to 1-1/2” from 10S to 80S size 2” from - to Sch

80 sizes 10” thru 24”

Revise Nipples and Swages from Sch 10S and 40S to 80S

Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)

01 D06

Revised pipe schedules from 10S to 80S sizes to 1-1/2” from 10S to 80S size 2” from - to Sch

80 sizes 16” thru 24”

Revise Swage PE from Sch 10S to 80S

01 D06N

Revised pipe schedules from 10S to 80S sizes to 1-1/2” from 10S to 80S size 2” from - to Sch

80 sizes 20” and 24”

Revise Swage PE from Sch 10S and 40S to 80S

01 D08

Revised pipe schedules from 10S to 80S sizes to 11/2” from 10S to 80S size 2” to 4” from

-to Sch 80 sizes 10” thru 24”

Revise Nipples and Swages from Sch 10S and 40S to 80S

01 D08N

Revised pipe schedules from 10S to 80S sizes to 11/2” from 10S to 80S size 2” to 4” from

-to Sch 80 sizes 10” thru 24”

(4)

DIVISION

Engineering Specification

Custom Process System (CPS)

CPS-03-7.3-007

Revision: 01

Date:

Dec 20, 2013

Page:

4 of 45

Title:

STANDARD PIPING CLASSES

Prepared by:

Reviewed by:

Approved by:

Steven Roberts

Oleg Barsky

Greg Dodson

1.0 SCOPE

The purpose of this specification is to establish standard piping classes to determine the

materials, schedules, valves, bolting, and construction for piping that is in full conformance with

B31.3 Process Piping. This specification is to be used when we are designing to Cameron

standard, and when a client does not furnish the proper client specifications.

2.0 RULES, DESIGN CODES AND STANDARDS

Codes and standards used in the stress analysis shall be the latest edition, including latest addenda,

supplements and revisions.

3.0 PIPING CLASS INDEX

Line

Class

Rev

Date

Rating / Material

Corrosion

Allowance

Service

A01

1 5-MAR-2014

Class 150 / Carbon Steel

1/16”(1.8mm)

General Process

A01N

1 5-MAR-2014

Class 150 / Carbon Steel NACE

1/8” (3.2mm)

General Process –

Sour Service

A02

1 5-MAR-2014

Class 150 / 304 Stainless Steel

None

General Process

A02N

1 5-MAR-2014

Class 150 / 304 Stainless Steel

-NACE

None

General Process –

Sour Service

A02CR

0 5-MAR-2014

Class 150 / 304 Stainless Steel

None

Cryogenic Service

A03

1 5-MAR-2014

Class 150 / Low Temp CS

1/16”(1.8mm)

General Process

A03N

1 5-MAR-2014

Class 150 / Low Temp CS - NACE

1/8” (3.2mm)

General Process –

Sour Service

A04

1 5-MAR-2014

Class 150 / 316 Stainless Steel

None

General Process

A04N

1 5-MAR-2014

Class 150 / 316 Stainless Steel

-NACE

None

General Process –

Sour Service

A06

1 5-MAR-2014

Class 150 / Duplex

None

General Process

A06N

1 5-MAR-2014

Class 150 / Duplex - NACE

None

General Process –

Sour Service

A08

1 5-MAR-2014

Class 150 / Super Duplex

None

General Process

A08N

1 5-MAR-2014

Class 150 / Super Duplex - NACE

None

General Process –

(5)

DIVISION

Engineering Specification

Custom Process System (CPS)

CPS-03-7.3-007

Revision: 01

Date:

Dec 20, 2013

Page:

5 of 45

Title:

STANDARD PIPING CLASSES

Prepared by:

Reviewed by:

Approved by:

Steven Roberts

Oleg Barsky

Greg Dodson

Line

Class

Rev

Date

Rating / Material

Corrosion

Allowance

Service

B01

1 5-MAR-2014

Class 300 / Carbon Steel

1/16”(1.8mm)

General Process

B01N

0 20-DEC-2013

Class 300 / Carbon Steel NACE

1/8” (3.2mm)

General Process –

Sour Service

B02

1 5-MAR-2014

Class 300 / 304 Stainless Steel

None

General Process

B02N

1 5-MAR-2014

Class 300 / 304 Stainless Steel

-NACE

None

General Process –

Sour Service

B02CR

0 5-MAR-2014

Class 300 / 304 Stainless Steel

None

Cryogenic Service

B03

1 5-MAR-2014

Class 300 / Low Temp CS

1/16”(1.8mm)

General Process

B03N

1 5-MAR-2014

Class 300 / Low Temp CS - NACE

1/8” (3.2mm)

General Process –

Sour Service

B04

1 5-MAR-2014

Class 300 / 316 Stainless Steel

None

General Process

B04N

1 5-MAR-2014

Class 300 / 316 Stainless Steel

-NACE

None

General Process –

Sour Service

B06

1 5-MAR-2014

Class 300 / Duplex

None

General Process

B06N

1 5-MAR-2014

Class 300 / Duplex - NACE

None

General Process –

Sour Service

B08

1 5-MAR-2014

Class 300 / Super Duplex

None

General Process

B08N

1 5-MAR-2014

Class 300 / Super Duplex - NACE

None

General Process –

Sour Service

D01

0 20-DEC-2013

Class 600 / Carbon Steel

1/16”(1.8mm)

General Process

D01N

0 20-DEC-2013

Class 600 / Carbon Steel NACE

1/8” (3.2mm)

General Process –

Sour Service

D02

1 5-MAR-2014

Class 600 / 304 Stainless Steel

None

General Process

D02N

1 5-MAR-2014

Class 600 / 304 Stainless Steel

-NACE

None

General Process –

Sour Service

D02CR

0 5-MAR-2014

Class 600 / 304 Stainless Steel

None

Cryogenic Service

D03

1 5-MAR-2014

Class 600 / Low Temp CS

1/16”(1.8mm)

General Process

D03N

1 5-MAR-2014

Class 600 / Low Temp CS - NACE

1/8” (3.2mm)

General Process –

Sour Service

D04

1 5-MAR-2014

Class 600 / 316 Stainless Steel

None

General Process

D04N

1 5-MAR-2014

Class 600 / 316 Stainless Steel

-NACE

None

General Process –

Sour Service

D06

1 5-MAR-2014

Class 600 / Duplex

None

General Process

D06N

1 5-MAR-2014

Class 600 / Duplex - NACE

None

General Process –

Sour Service

D08

1 5-MAR-2014

Class 600 / Super Duplex

None

General Process

D08N

1 5-MAR-2014

Class 600 / Super Duplex - NACE

None

General Process –

(6)

Revis ion Prepared Checked Approved 0 SR OB GD 1 SR SB GD 1/2" 3/4" 1" 1-1/2" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" Sch Ends Matl Sch Rating Matl Gate Ball Globe Check Butterfly Needle / Gauge Notes : 1.

2.

Temp °F

PSIG Temp °C

BAR

3.

_{-20 to 100}

₂₈₅

_{-29 to 38 19.6}

200

260

50

19.2

4.

300

230

100

17.7

5.

₄₀₀

₂₀₀

₁₅₀

_15.8

500

170

200

13.8

6.

600

140

250

12.1

7.

₆₅₀

₁₂₅

₃₀₀

_10.2

700

110

325

9.3

8

750

95

350

8.4

800

80

375

7.4

400

6.5

425

5.5

24 20 18 16 14 12 10 8 6 4 3 2 1 1/2 1 3/4 1/2 24 WT 20 WRT WT 18 WRT WRT WT 16 WRT WRT WRT WT 14 WRT WRT WRT WRT WT 12 WRT WRT WRT WRT WRT WT 10 WOL WRT WRT WRT WRT WRT WT

8 WOL WOL WOL WRT WRT WRT WRT WT

6 WOL WOL WOL WOL WOL WRT WRT WRT WT

4 WOL WOL WOL WOL WOL WOL WOL WRT WRT WT

3 WOL WOL WOL WOL WOL WOL WOL WOL WRT WRT WT

2 WOL WOL WOL WOL WOL WOL WOL WOL WOL WRT WRT WT

1 1/2 SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SWT 1 SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SWTS SWT 3/4 SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SWTS SWTS SWT 1/2 SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SWTS SWTS SWTS SWT

SWTS Full s ize SW Tee with Swage SOL Sockolet WOL Weldolet WT Butt Weld Tee SWT Socket Weld Tee TOL Threadolet WRT Butt Weld Reducing Tee

Sch 80 Sch 40

19-Dec-2013

PIPING SPECIFICATION - ASME CLASS 150, CARBON STEEL Specification

A01

Document No

Cam eron Standard - Issued for Design 5-Mar-2014 Revise Pipe Sch Nipples , Swages

Liquids and Vapors - General Process

Pipe Size

Pipe

STD

Plain End (PE) Beveled End (BE)

Seam less , ASTM A-106-B (Note 8) ASME CLASS 150

Rating Piping Code Material / Group Temp Range Corrosion Allowance

Hydrotes t Pres sure

ASME B31.3 Carbon Steel (1.1) 0.0625" (1.6m m )

Date Description Service -20°F / +600°F -29°C / 316°C 428 psig 29.5 barg Flanges

Flange Bore to Match Pipe

150# RF SW (Note 2) 150# RFWN (Note 2)

ASTM A-105

Fittings 3000# FS, A-105 (Note 7) Seam less , ASTM A-234 WPB, Butt Weld, Bore to m atch pipe (Note 3) Unions 3000# FS, SW, A-105 (Note 7)

Plugs (Note 6) 6000# FS, Hex Head, threaded, Plated, A-105 Couplings 3000# FS, Full, Threaded, A-105 Nipples (thd x thd) Sch 160 Seam less , A-106-B Nipples (PE x thd) Sch 160 Seam less , A-106-B

Swages (thd x thd) Sch 160 Seamless, A-106-B or A-234-WPB

Swages (PE x thd) Sch 160 Seamless, A-106-B or A-234-WPB Swages (PE both

ends)

Sch 80, Seamless A-106-B or A-234-WPB Sockolets 3000# FS, A-105 Threadolets 3000# FS, A-105

Weldolets A-105, bore to m atch branch piping

Gaskets (RF Flanges) 1/16” thk, ANSI B16.21, Synthetic Com press ed Fiber with Nitrile Binder, Klinger C4401 or equivalent

(FF Flanges ) 1/16” thk, ANSI B16.21, Full-Faced, Synthetic Compres sed Fiber with Nitrile Binder, Klinger C4401 or equivalent

-20 / 100°F pres sure rating is used to determ ine the required pipe wall thicknes s. Temp / Press ure Ratings Use FF flange for connection to FF cast iron or ductile iron flanges for equipment

Butt weld reducing fittings shall be purchased to the heavier pipe schedule. Piping drawing notes will indicate where internal beveling is required Bolting

Bolts / Cap Screws, Alloy Steel, A-193-B7, Fluorocote No. 1 finis h Nuts, Alloy Steel, sem i-finished, A-194-2H, Fluorocote No. 1 finish Washers, s teel, F436, Fluorocote No. 1 finis h

V A L V E S (N o te s 4 , 5 ) D1Z, D1S, D1S-S A1R D2Z, D2ZF, D2S, D2SF, D2S-S, D2SF-S A2R, A2RF D4Z, D4S, D4S-S A4R

D5Z, D5S, D5S-S A5R, A5RG, A5RW

A7RG, A7RW G6S-S, G9S-S B R A N C H S IZ E HEADER SIZE

Pipe material may be A106 Gr B seam less , API-5L Gr B s eam les s or A53B seam less Item s may be cad plated, zinc plated, or galvanized

Welded construction to be used for in-line process piping. Threaded connections and fittings are perm itted for instrum ent take-offs, piping vent and drain valves

Carbon steel body valves m ay be A-105 forged s teel or A-216-WCB cas tings.

Valves with elas tom er s eats and/or seals m ay not be rated for full ANSI press ure-tem perature values. Refer to P&ID's and/or Equipm ent Data Sheets for s ys tem upper lim it des ign temperature.

(7)

Revis ion Prepared Checked Approved 0 SR OB GD 1 SR SB GD 1/2" 3/4" 1" 1-1/2" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" Sch Sch 80 Ends Matl Sch Rating Matl Gate (4) Ball (4,5) Globe (4) Check (4) B utterfly (5) Needle / Gauge Notes : 1

2

Temp °F

PSIG Temp °C

BAR

3

-20 to 100

285 -29 to 38

19.6

200

260

50

19.2

4

300

230

100

17.7

5

400

200

150

15.8

500

170

200

13.8

6

600

140

250

12.1

7

650

125

300

10.2

700

110

325

9.3

8 Pipe material may be A106 Gr B s eamles s , API-5L Gr B s eamles s or A53B s eamles s

750

95

350

8.4

800

80

375

7.4

400

6.5

425

5.5

Gas kets (RF Flanges ) 1/16” thk, ANSI B16.21, Full-Faced, Synthetic Com pres s ed Fiber with Nitrile Binder, Klinger C4401 or equivalent (FF Flanges ) 1/16” thk, ANSI B16.21, Full-Faced, Synthetic Compres s ed Fiber with Nitrile Binder, Klinger C4401 or equivalent

Bolting

Bolts / Cap Screws , Alloy Steel, A-193-B7M, Fluorocote No. 1 finis h Nuts , Alloy Steel, s em i-finis hed, A-194-2HM, Fluorocote No. 1 finis h Was hers , s teel, F436, Fluorocote No. 1 finis h

428 ps ig 29.5 barg B R A N C H S IZ E HEADER SIZE Carbon s teel body valves m ay be A-105 forged s teel or A-216-WCB cas tings .

Valves with elas tomer s eats and/or s eals m ay not be rated for full ANSI pres s ure-tem perature values . Butt weld reducing fittings s hall be purchas ed to the heavier pipe s chedule.

Piping drawing notes will indicate where internal beveling is required

Welded cons truction to be us ed for in-line proces s piping. Threaded connections are perm itted for ins trum ent take-offs , piping vent and drain valves

Refer to P&ID's and/or Equipm ent Data Sheets for s ys tem upper limit des ign tem perature. Items m ay be cad plated, zinc plated, or galvanized

V A L V E S D1Z-N, D1S-N, D1S-SN A1R-N, A1RF-N D2Z-N, D2ZF-N, D2S-N, D2SF-N, D2S-SN A2R-N, A2RF-N Threadolets

Weldolets A-105, bore to match branch piping

Flanges

150# RF SW (Note 2) 150# RFWN (Note 2)

ASTM A-105

Nipples (thd x thd) Sch XXH Seamles s , A-333-6 Plugs (Note 6) 6000# FS, Hex Head, threaded,

Plated, A-105 Couplings 3000# FS, Full, Threaded, A-105

G6S-SN, G9S-SN

-20 / 100°F pres s ure rating is us ed to determ ine the required pipe wall thicknes s . Temp / Pres s ure Ratings Us e FF flange for connection to FF cas t iron or ductile iron flanges for equipment

Fittings 3000# FS, A-105 (Note 7) Seam les s , ASTM A-234 WPB, Butt Weld, Bore to match pipe (Note 3) Unions 3000# FS, SW, A-105 (Note 7)

Nipples (PE x thd) Sch XXH Seamles s , A-333-6

Swages (PE both ends )

Sch160, Seamles s A-333-6 or A-420-WPL6 (note 8) Sockolets 3000# FS, A-105 Swages (thd x thd) Sch XXH, Seamles s

A-333-6 or A-420-WPL6

Swages (PE x thd)

A7RG-N, A7RW-N

Material / Group Temp Range Corros ion Allowance

Hydrotes t Pres s ure

Seam les s , ASTM A-333-6 Seamles s ASTM A-106-B (NOTE 8) ASME B31.3 Carbon Steel (1.1)

Sch XXH, Seamles s A-333-6 or A-420-WPL6 -20°F / +600°F -29°C / 316°C Sch 40 Sch 160 D4Z-N, D4S-N, D4S-SN A4R-N

D5Z-N, D5S-N, D5S-SN A5R-N, A5RG-N, A5RW-N 3000# FS, A-105

Rating Piping Code

Pipe Size

Pipe

PIPING SPECIFICATION - ASME CLASS 150, CARBON STEEL (NACE) Specification

A01N

Document No

Date Des cription

19-Dec-2013 Cameron Standard - Is s ued for Des ign 5-Mar-2014 Revis e Gas kets (RF Flanges )

0.125" (3.2mm ) ASME CLASS 150

Service

Liquids and Vapors - General Proces s

(8)

Revision Prepared Checked Approved 0 SR OB GD 1 SR SB GD 1/2" 3/4" 1" 1-1/2" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" Sch Ends Matl Sch Rating Matl Gate (4) Ball (4,5) Globe (4) Check (4) B utterfly (5) Needle / Gauge Notes : 1

2 Temp °F PSIG Temp °C BAR

3 -50 to 100 275 -46 to 38 19

200 230 50 18.3

4 300 205 100 15.7

or may be certified for 304 with chemis try that meets 304L 400 190 150 14.2

5 500 170 200 13.2 600 140 250 12.1 6 650 125 300 10.2 7 700 110 325 9.3 750 95 350 8.4 8 800 80 375 7.4 400 6.5 425 5.5 24 20 18 16 14 12 10 8 6 4 3 2 1 1/2 1 3/4 1/2 24 WT 20 WRT WT 18 WRT WRT WT 16 WRT WRT WRT WT 14 WRT WRT WRT WRT WT 12 WRT WRT WRT WRT WRT WT 10 WOL WRT WRT WRT WRT WRT WT

8 WOL WOL WOL WRT WRT WRT WRT WT 6 WOL WOL WOL WOL WOL WRT WRT WRT WT 4 WOL WOL WOL WOL WOL WOL WOL WRT WRT WT 3 WOL WOL WOL WOL WOL WOL WOL WOL WRT WRT WT 2 WOL WOL WOL WOL WOL WOL WOL WOL WOL WRT WRT WT

1 1/2 SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SWT 1 SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SWTS SWT 3/4 SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SWTS SWTS SWT

1/2 SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SWTS SWTS SWTS SWT SWTS Full s ize SW Tee with Swage SOL Sockolet WOL Weldolet WT Butt Weld Tee

SWT Socket Weld Tee TOL Threadolet WRT Butt Weld Reducing Tee Fittings

Pipe

Flanges

Beveled End (BE)

Swages (PE x PE) Swages (PE x thd)

Swages (thd x thd) Sch 80S Seamles s A312-TP304/304L Sch 80S Seamles s A312-TP304/304L Sch 80S Seamles s A312-TP304/304L

3000# FS, A-182-F304/304L Sch 80S Seam less , A-312-TP304/304L

A4R-S

A7RG-S, A7RW-S Nipples (thd x thd) Sch 80S Seamless A-312-TP304/304L

Nipples (PE x thd)

instrument take-offs, piping vent and drain valves

Welded cons truction to be us ed for in-line proces s piping. Threaded connections are perm itted for

HEADER SIZE Seam less pipe and weld fittings may be s ubs tituted for ERW pipe and weld fittings . Refer to P&ID's and/or Equipm ent Data Sheets for s ystem upper limit design temperature.

B R A N C H S IZ E

Weldolets A-182-F304/304L, bore to m atch branch piping

(FF Flanges) 1/16” thk, ANSI B16.21, Full-Faced, Synthetic Compres sed Fiber with Nitrile Binder, Klinger C4401 or equivalent

V A L V E S D5Z-S, D5S-S Gas kets A2R-S, A2RF-S D1Z-S, D1S-S

Nuts , Alloy Steel, semi-finished,A-194-8 Was hers , 316 Stainless Steel

(RF Flanges ) 1/16” thk, ANSI B16.21, Synthetic Compres sed Fiber with Nitrile Binder, Klinger C4401 or equivalent

Temp / Pressure Ratings

Where materials are shown to be dual certified, m aterials may be supplied dual certified for 304/304L Us e FF flange for connection to equipm ent with FF connections

Butt weld reducing fittings shall be purchas ed to the heavier pipe schedule. Piping drawing notes will be provided to indicate where internal beveling is required

Valves are s uitable for -50°F s ervice tem perature. 3000# FS, A-182-F304/304L (note 7)

3000# FS, A-182-F304

A-403-WP304, Butt Weld, Welded (100% JE), Bore to m atch pipe (Notes 3, 8) ASTM A-403-WP304/304L, Butt Weld, Seam less ,

Bore to match pipe (Notes 3, 8) Unions

Date Description

12-Dec-2013

A02

150# RF SW (note 2)

Cameron Standard - Is sued for Des ign

Rating

ASME CLASS 150

Piping Code Material / Group Hydrotes t Press ure

NONE Liquids and Vapors - General Process

Pipe Size

PIPING SPECIFICATION - ASME CLASS 150 - 304/304L STAINLESS STEEL

Tem p Range

Specification

Document No

Flange Bore to Match Pipe Plain End (PE)

150# RFWN (note 2) ASTM A-182-F304

ASTM A-312-TP304/304L Seamless Type 304 (2.1)

(note 4)

ASTM A312-Grade 304/304L ERW (note 8) -50°F / +600°F

-46°C / 316°C

413 ps ig 28.5 barg 5-Mar-2014 Revise Pipe Sch, Nipples , Swages

Corros ion Allowance

ASME B31.3

Service

Sch 80S Sch 40S Sch 10S

Valves with elastomer s eats and/or s eals may not be rated for full ANSI pres sure-temperature values 100°F press ure rating is used to determine the required pipe wall thicknes s.

Plugs 6000# FS, Hex Head, Thd, A-182-F304

3000# FS, Full, Threaded A-182-F304

Sockolets Threadolets 3000# FS, A-182-F304/304L Bolting (Note 5) D2Z-S, D2ZF-S, D2S-S, D2SF-S A1R-S G6S-S, G9S-S

A5R-S, A5RG-S, A5RW-S Couplings

D4Z-S, D4S-S

(9)

Revision Prepared Checked Approved 0 SR OB GD 1 SR SB GD 1/2" 3/4" 1" 1-1/2" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" Sch Ends Matl Sch Rating Matl Gate (4) Ball (4,5) Globe (4) Check (4) B utterfly (5) Needle / Gauge Notes: 1

2 Tem p °F PSIG Temp °C BAR

3 -50 to 100 275 -46 to 38 19

200 230 50 18.3

4 300 205 100 15.7

or may be certified for 304 with chemistry that meets 304L 400 190 150 14.2

SWTS Full size SW Tee with Swage SOL Sockolet WOL Weldolet WT Butt Weld Tee SWT Socket Weld Tee TOL Threadolet WRT Butt Weld Reducing Tee

Sch 40S Sch 10S

Hydrotest Pressure Temp Range Corrosion

Allowance ASME B31.3 Service Threadolets 3000# FS, A-182-F304/304L 3000# FS, A-182-F304/304L (note 7) 3000# FS, A-182-F304

A-403-WP304, Butt Weld, Welded (100% JE), Bore to match pipe (Notes 3, 8) ASTM A-403-WP304/304L, Butt Weld, Seamless,

Bore to match pipe (Notes 3, 8) Unions

Bolting (Note 5)

D2Z-SN, D2ZF-SN, D2S-SN, D2SF-SN A1R-SN

G6S-SN, G9S-SN

A5R-SN, A5RG-SN, A5RW-SN Pipe Size

Fittings

D4Z-SN, D4S-SN

Bolts / Cap Screws, Alloy Steel, A-193-B8 3000# FS, A-182-F304/304L

NONE

Welded construction to be used for in-line process piping. Threaded connections are permitted for Beveled End (BE)

A2R-SN, A2RF-SN D1Z-SN, D1S-SN

Nuts, Alloy Steel, semi-finished,A-194-8

Not required unless pipe is externally coated. If provided, washers are to be 316 stainless steel

(RF Flanges) 1/8” thk, ANSI B16.21, Spiral Wound, 316SS with Graphite Filler, Flexitallic Style CG or equivalent

Where materials are shown to be dual certified, materials may be supplied dual certified for 304/304L Use FF flange for connection to equipment with FF connections

Butt weld reducing fittings shall be purchased to the heavier pipe schedule. Piping drawing notes will be provided to indicate where internal beveling is required

Valves are suitable for -50°F s ervice temperature.

Valves with elastom er seats and/or seals m ay not be rated for full ANSI pressure-temperature values 100°F pressure rating is used to determine the required pipe wall thickness.

Sch 80S

HEADER SIZE Seamless pipe and weld fittings may be substituted for ERW pipe and weld fittings.

A7RG-SN, A7RW-SN

Refer to P&ID's and/or Equipment Data Sheets for system upper limit design temperature. Plugs 6000# FS, Hex Head, Thd, A-182-F304

Sockolets Flanges

A4R-SN Sch 80S Seam less A-312-TP304/304L

B R A N C H S IZ E

Weldolets A-182-F304/304L, bore to match branch piping Sch 80S Seamless, A-312-TP304/304L

(FF Flanges) 1/16” thk, ANSI B16.21, Full-Faced, Synthetic Compressed Fiber with Nitrile Binder, Klinger C4401 or equivalent

V A L V E S D5Z-SN, D5S-SN Gaskets

PIPING SPECIFICATION - ASME CLASS 150 - 304/304L STAINLESS STEEL (NACE) Specification

Document No

150# RFWN (note 2) ASTM A-182-F304

ASTM A-312-TP304/304L Seam less Type 304 (2.1)

(note 4)

ASTM A312-Grade 304/304L ERW (note 8)

Date Description

19-Dec-2013

A02N

150# RF SW (note 2)

Cameron Standard - Issued for Design 5-Mar-2014 Revise Pipe Sch, Nipples, Swages

-50°F / +600°F -46°C / 316°C

413 psig 28.5 barg Piping Code Material / Group

Swages (thd x thd) Sch 80S Seamless A312-TP304/304L Swages (PE x thd) Sch 80S Seamless A312-TP304/304L Swages (PE x PE) Sch 80S Seamless A312-TP304/304L

Rating ASME CLASS 150 Nipples (thd x thd) Nipples (PE x thd) Couplings Pipe

(10)

Prepared Checked Approved SB TW GD 1/2" 3/4" 1" 1-1/2" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" Sch Ends Matl Sch Rating Matl Gate Ball (5) Globe Check B utterfly (5) Needle Notes : 1

3 -175 to 100 275 -115 to 38 19 200 230 50 18.3 4 300 205 100 15.7 400 190 150 14.2 5 500 170 200 13.2 600 140 250 12.1 650 125 300 10.2 700 110 325 9.3 6 750 95 350 8.4 7 800 80 375 7.4 400 6.5 425 5.5 24 20 18 16 14 12 10 8 6 4 3 2 1 1/2 1 3/4 1/2 24 WT 20 WRT WT 18 WRT WRT WT 16 WRT WRT WRT WT 14 WRT WRT WRT WRT WT 12 WRT WRT WRT WRT WRT WT 10 WOL WRT WRT WRT WRT WRT WT

1 1/2 SOL SOL SOL SOL SOL SOL SOL SOL SOL SOL SOL SOL SWT

1 SOL SOL SOL SOL SOL SOL SOL SOL SOL SOL SOL SOL SWTS SWT 3/4 SOL SOL SOL SOL SOL SOL SOL SOL SOL SOL SOL SOL SWTS SWTS SWT 1/2 SOL SOL SOL SOL SOL SOL SOL SOL SOL SOL SOL SOL SWTS SWTS SWTS SWT

SWTS Full s ize SW Tee with Swage SOL Sockolet (or other O-Let) WOL Weldolet WT Butt Weld Tee SWT Socket Weld Tee TOL Threadolet (not permitted) WRT Butt Weld Reducing Tee

0 5-Mar-2014

PIPING SPECIFICATION - 150# RF, 304 Stainless Steel - Cryogenic Specification

A02CR

Document No

Rev No Date Description Cameron Standard - Is sued for Des ign

Service

ANSI 150LB ASME B31.3 Type 304 (2.1)

(Note 4) -175°F / +600°F None 413 ps ig Liquids and Vapors - General Process Rating Piping Code Material / Group Tem p Range Corros ion

Allowance Hydrotes t Pres sure Pipe Size Pipe Sch 80S Sch 40S

Seamless , ASTM A-312-TP304 ASTM A-312-TP304 ERW

Sch 10S Sch 10

Fittings 3000# FS, A-182-F304 (Note 7) Seamles s , ASTM A-403-WP304, Butt Weld, Bore to match pipe (Note 3) Unions Not permitted for proces s piping

Flanges

150# RF SW 150# RFWN

ASTM A-182-F304

Nipples (thd x thd) Sch 80S s mls A-312-TP304 Nipples (PE x thd) Sch 80S s mls A-312-TP304 Plugs 6000# FS, Hex Head, threaded,

A-182-F304

Couplings 3000# FS, Full, Threaded, A-182-F304

Swages (PE both ends ) Sch 80S, Smls , A-312-TP-304 or A-403-WP304 O-Lets 3000# FS, A-182-F304 Swages (thd x thd) Sch 80S, Smls , A-312-TP-304 or A-403-WP304

Swages (PE x thd) Sch 80S, Smls , A-312-TP-304 or A-403-WP304

Gas kets (RF Flanges ) 1/8” thk, ANSI B16.21, Spiral Wound, 304SS, Graphite Filler, SS outer ring, Flexitallic CG or equivalent

Bolting

Bolts / Cap Screws , Alloy Steel, A-193-B8 Nuts, Alloy Steel, semi-finished, A-194-8 Washers - Not Required for this s ervice Threadolets Not permitted for proces s piping

Weldolets A-182-F-304 bore to match branch piping

A7R-SCR G6S-SCR, G9S-SCR

100°F pres s ure rating is used to determ ine the required pipe wall thickness . Temp / Pres sure Ratings Threaded connections are not permitted beneath ins ulation. Seal welding is premitted.

V a lv e s D1Z-SCR, D1S-SCR, D1X-SCR A1R-SCR D2Z-SCR, D2ZF-SCR A2R-SCR, A2RF-SCR D4Z-SCR A4R-SCR D5Z-SCR, D5S-SCR, D5X-SCR A5R-SCR, A5RW-SCR

Grade 316 or 316/316L may be subs tituted for Grade 304 or 304/304L Butt weld reducing fittings shall be purchased to the heavier pipe s chedule. Piping drawing notes will indicate where internal beveling is required

Materials may be specified and purchased as grade 304L, or dual certified 304 / 304L

B R A N C H S IZ E HEADER SIZE Valves are s uitable for Cryogenic temperature s ervice to -175°F

Welded cons truction to be used for in-line proces s piping through the first ins trument is olation valve. Threaded connection are permitted only for connections to ins truments outs ide of insulation

equipment data s heets for s ys tem des ign press ure and upper limit des ign temperature. High temperature ball and butterfly valves will be required to be m etal s eated.

Standard valves having elas tomer s eats are typically rated for 250 ps ig maximum tem perature. Valves with elas tomer seals may not be rated for full ANSI pres s ure-temperature values . Refer to P&ID's and/or

(11)

Revis ion Prepared Checked Approved 0 SR OB GD 1 SR SB GD 1/2" 3/4" 1" 1-1/2" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" Sch Ends Matl Sch Rating Matl Gate (4) Ball (4,5) Globe (4) Check (4) B utterfly (5) Needle / Gauge Notes : 1

2 Tem p °F PSIG Tem p °C BAR

3 -50 to 100 285 -46 to 38 19.6 200 260 50 19.2 4 300 230 100 17.7 400 200 150 15.8 5 500 170 200 13.8 600 140 250 12.1 6 650 125 300 10.2 7 700 110 325 9.3 750 95 350 8.4 800 80 375 7.4 400 6.5 425 5.5 24 20 18 16 14 12 10 8 6 4 3 2 1 1/2 1 3/4 1/2 24 WT 20 WRT WT 18 WRT WRT WT 16 WRT WRT WRT WT 14 WRT WRT WRT WRT WT 12 WRT WRT WRT WRT WRT WT 10 WOL WRT WRT WRT WRT WRT WT

B R A N C H S IZ E HEADER SIZE Item s m ay be cad plated, zinc plated, or galvanized

Welded cons truction to be us ed for in-line proces s piping. Threaded connections are perm itted for Butt weld reducing fittings s hall be purchas ed to the heavier pipe s chedule.

Piping drawing notes will indicate where internal beveling is required A7RG-L, A7RW-L

G6S-S, G9S-S

-50 / 100°F pres s ure rating is us ed to determ ine the required pipe wall thicknes s . Tem p / Pres s ure Ratings Us e FF flange for connection to FF cas t iron or ductile iron flanges for equipm ent

Valves with elas tom er s eats and/or s eals m ay not be rated for full ANSI pres s ure-tem perature values .

V A L V E S D1Z-L, D1S-L, D1S-S A1R-L D2ZF-L, D2S-L, D2SF-L, D2S-S, D2SF-S A2R-L, A2RF-L D4Z-L, D4S-L, D4S-S A4R-L

D5Z-L, D5S-L, D5S-S A5R-L, A5RG-L, A5RW-L

ins trum ent take-offs , piping vent and drain valves

Refer to P&ID's and/or Equipm ent Data Sheets for s ys tem upper lim it des ign tem perature.

Gas kets (RF Flanges ) 1/16” thk, ANSI B16.21, Synthetic Com pres s ed Fiber with Nitrile Binder, Klinger C4401 or equivalent

(FF Flanges ) 1/16” thk, ANSI B16.21, Full-Faced, Synthetic Com pres s ed Fiber with Nitrile Binder, Klinger C4401 or equivalent

Bolting

Bolts / Cap Screws , Alloy Steel, A-320-L7, Fluorocote No. 1 finis h Nuts , Alloy Steel, s em i-finis hed, A-194-7, Fluorocote No. 1 finis h Was hers , s teel, F436, Fluorocote No. 1 finis h

Carbon s teel body valves m ay be A-350-LF2, Cl. 1 forged s teel or A-352-LCC cas tings . A-352-LCB cas tings m ay be us ed provided the s ys tem des ign pres s ure and tem perature are com patible with B16.5 ratings . Threadolets 3000# FS, A-350-LF2, Cl. 1

Weldolets A-350-LF2, Cl. 1, bore to m atch branch piping

Sch 80 Seam les s A-333-6 or A-420-WPL6 Sockolets 3000# FS, A-350-LF2, Cl. 1 Swages (thd x thd) Sch 160, Seam les s ,

A-333-6 or A-420-WPL6

Swages (PE x thd) Sch 160, Seam les s , A-333-6 or A-420-WPL6 Nipples (thd x thd) Sch 160 Seam les s , A-333-6 Nipples (PE x thd) Sch 160 Seam les s , A-333-6 Plugs (Note 6) 6000# FS, Hex Head, threaded,

Plated, A-350-LF2, Cl. 1 Couplings 3000# FS, Full, Threaded, A-350-LF2, Cl. 1

Fittings 3000# FS, A-350-LF2, Cl. 1 (Note 7) Seam les s , ASTM A-420-WPL6 Butt Weld, Bore to m atch pipe (Note 2) Unions 3000# FS, SW, A-350-LF2, Cl. 1 (Note 7)

Flanges

ASTM A-350-LF2, Cl. 1 Pipe Size

Pipe

Sch STD

Seam les s , ASTM A-333 Gr 6

Sch 80 Sch 40

Service

ASME CLASS 150 ASME B31.3 Carbon Steel (1.1) 0.0625" Liquids and Vapors - General Proces s Rating Piping Code Material / Group Tem p Range Corros ion

Allowance Hydrotes t Pres s ure -50°F / +600°F -46°C / 316°C 428 ps ig 29.5 barg

PIPING SPECIFICATION - ASME CLASS 150, Low Temperature Carbon Steel Specification

A03

Document No

Date Des cription

19-Dec-2013 Cam eron Standard - Is s ued for Des ign 5-Mar-2014 Revis e Pipe Sch, Nipples , Swages

(12)

Revision Prepared Checked Approved 0 SR OB GD 1 SR SB GD 1/2" 3/4" 1" 1-1/2" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" Sch Ends Matl Sch Rating Matl Gate (4) Ball (4,5) Globe (4) Check (4) B utterfly (5) Needle / Gauge Notes : 1

2 Tem p °F PSIG Temp °C BAR

3 -50 to 100 285 -46 to 38 19.6 200 260 50 19.2 4 300 230 100 17.7 400 200 150 15.8 5 500 170 200 13.8 600 140 250 12.1 6 650 125 300 10.2 7 700 110 325 9.3 750 95 350 8.4 800 80 375 7.4 400 6.5 425 5.5 24 20 18 16 14 12 10 8 6 4 3 2 1 1/2 1 3/4 1/2 24 WT 20 WRT WT 18 WRT WRT WT 16 WRT WRT WRT WT 14 WRT WRT WRT WRT WT 12 WRT WRT WRT WRT WRT WT 10 WOL WRT WRT WRT WRT WRT WT

PIPING SPECIFICATION - ASME CLASS 150, Low Temperature Carbon Steel (NACE) Specification

A03N

Document No

Date Description

19-Dec-2013 Cam eron Standard - Is s ued for Des ign 5-Mar-2014 Revis e Pipe Sch

Service

ASME CLASS 150 ASME B31.3 Carbon Steel (1.1) 0.125" (3.2m m ) Liquids and Vapors - General Proces s

Rating Corros ion

Allowance Hydrotest Press ure -50°F / +600°F -46°C / 316°C 428 psig 29.5 barg Flanges

ASTM A-350-LF2, Cl. 1 Pipe Size

Pipe

Sch STD

Seam les s, ASTM A-333 Gr 6

Sch 160 Sch 80 Sch 40

Plugs (Note 6) 6000# FS, Hex Head, threaded, Plated, A-350-LF2, Cl. 1 Couplings 3000# FS, Full, Threaded, A-350-LF2, Cl. 1

Fittings 3000# FS, A-350-LF2, Cl. 1 (Note 7) Seamless , ASTM A-420-WPL6 Butt Weld, Bore to m atch pipe (Note 2) Unions 3000# FS, SW, A-350-LF2, Cl. 1 (Note 7)

Swages (thd x thd) Sch XXH Seam les s, A-333-6-B or A-420-WPL6

Swages (PE x thd) Sch XXH Seam les s, A-333-6 or A-420-WPL6 Nipples (thd x thd) Sch XXH Seam les s , A-333-6 Nipples (PE x thd) Sch XXH Seam les s , A-333-6

Threadolets 3000# FS, A-350-LF2, Cl. 1

Weldolets A-350-LF2, Cl. 1, bore to m atch branch piping

Sch 160 Seam les s A-333-6 or A-420-WPL6 Sockolets 3000# FS, A-350-LF2, Cl. 1

D5Z-LN, D5S-LN, D5S-SN A5R-LN, A5RG-LN, A5RW-LN A7RG-LN, A7RW-LN

G6S-SN, G9S-SN

Gas kets (RF Flanges ) 1/8” thk, ANSI B16.21, Spiral Wound, 316SS with Graphite Filler, Flexitallic Style CG or equivalent

(FF Flanges) 1/16” thk, ANSI B16.21, Full-Faced, Synthetic Compress ed Fiber with Nitrile Binder, Klinger C4401 or equivalent

Bolting

Bolts / Cap Screws, Alloy Steel, A-320-L7, Fluorocote No. 1 finish Nuts , Alloy Steel, s em i-finis hed, A-194-7, Fluorocote No. 1 finis h Washers, steel, F436, Fluorocote No. 1 finish

-50 / 100°F press ure rating is used to determ ine the required pipe wall thickness . Temp / Press ure Ratings Us e FF flange for connection to FF cast iron or ductile iron flanges for equipment

Piping Code Material / Group Temp Range

B R A N C H S IZ E HEADER SIZE

m ay be us ed provided the sys tem des ign pres sure and tem perature are compatible with B16.5 ratings . Butt weld reducing fittings s hall be purchased to the heavier pipe schedule.

Piping drawing notes will indicate where internal beveling is required

Item s m ay be cad plated, zinc plated, or galvanized

Welded construction to be us ed for in-line proces s piping. Threaded connections are perm itted for Valves with elastomer seats and/or seals may not be rated for full ANSI pres sure-tem perature values . Refer to P&ID's and/or Equipm ent Data Sheets for system upper limit design temperature.

Carbon steel body valves may be A-350-LF2, Cl. 1 forged steel or A-352-LCC cas tings. A-352-LCB castings

V A L V E S D1Z-LN, D1S-LN, D1X-LN, D1S-SN A1R-LN D2Z-LN, D2ZF-LN, D2X-LN, D2S-LN, D2SF-LN, D2SSN, D2SS-FN A2RLN, A2RF-LN D4Z-LN, D4S-LN, D4S-SN A4R-LN

(13)

3 -20 to 100 275 -29 to 38 19

200 235 50 18.4

4 300 215 100 16.2

or may be certified for 316 with chemistry that meets 316L 400 195 150 14.8

3000# FS, A-182-F316/316L (note 7)

A-403-WP316/316L, Butt Weld, Welded (100% JE), Bore to match pipe (Notes 3, 8) ASTM A-403-WP316/316L, Butt Weld, Seamless,

Bore to match pipe (Notes 3, 8) Material / Group

Fittings Pipe

Flanges

Beveled End (BE)

Unions 150# RFWN (note 2) ASTM A-182-F316/316L ASTM A-312-TP316/316L Type 316 (2.2) (note 4)

ASTM A312-Grade 316/316L ERW (note 8) Rating ASME CLASS 150 Pipe Size Sch 80S Sch. 40S Sch 10S A4R-S Nipples (thd x thd) Sch 80S Smls A-312-TP316 Swages (thd x thd) A7RG-S, A7RW-S Sch 80S Smls A-312-TP316/316L Nipples (PE x thd)

Swages (PE x thd) Sch 80S Smls A-403-WP316/316L

Bolting (Note 5)

D2Z-S, D2ZF-S, D2S-S, D2SF-S, D2X-S, D2XF-S

A1R-S

A5R-S, A5RG-S, A5RW-S 3000# FS, A-182-F316/316L

Sockolets

(FF Flanges) 1/16” thk, ANSI B16.21, Full-Faced, Synthetic Compressed Fiber with Nitrile Binder, Klinger C4401 or equivalent

V A L V E S D5Z-S, D5S-S Gaskets A2R-S, A2RF-S D1Z-S, D1S-S, D1X-S 3000# FS, A-182-F316/316L (note 7)

Where materials are shown to be dual certified, materials may be supplied dual certified for 316/316L Use FF flange for connection to equipment with FF connections

Valves are suitable for -50°F service temperature.

B R A N C H S IZ E

Weldolets A-182-F316/316L, bore to match branch piping

Refer to P&ID's and/or Equipment Data Sheets for system upper limit design temperature. G6S-S, G9S-S

Welded construction to be used for in-line process piping. Threaded connections are permitted for

HEADER SIZE Seamless pipe and weld fittings may be substituted for ERW pipe and weld fittings.

Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values 100°F pressure rating is used to determine the required pipe wall thickness.

Plugs 6000# FS, Hex Head, Thd, A-182-F316

Not required unless pipe is externally coated. If provided, washers are to be 316 stainless steel

(RF Flanges) 1/16” thk, ANSI B16.21, Synthetic Compressed Fiber with Nitrile Binder, Klinger C4401 or equivalent Couplings

D4Z-S, D4S-S

Bolts / Cap Screws, Alloy Steel, A-193-B8 3000# FS, A-182-F316/316L Threadolets Sch 80S Smls A-403-WP316 Date Description 20-Dec-2013

A04

150# RF SW (note 2)

Cameron Standard - Issued for Design

5-Mar-2014 Revise Pipe Sch, Nipples, Swages, Temp / Pressure Rating chart

413 psig 28.5 barg Hydrotest Pressure Temp Range Corrosion

Allowance -20°F / +600°F -29°C / 316°C ASME B31.3 Service NONE Piping Code

PIPING SPECIFICATION - ASME CLASS 150 - 316/316L STAINLESS STEEL

Specification

Document No

(14)

Revision Prepared Checked Approved 0 SR OB GD 1 SR SB GD 1/2" 3/4" 1" 1-1/2" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" Sch Ends Matl Sch Rating Matl Gate (4) D1Z-SN, D1S-SN, D1X-SN A1R-S

Ball (4,5) A2R-SN, A2RF-SN

Globe (4) D4Z-SN, D4S-SN A4R-SN

Check (4) D5Z-SN, D5S-SN A5R-SN, A5RG-SN, A5RW-SN

B utterfly (5) A7RG-SN, A7RW-SN

Needle /

Gauge G6S-SN, G9S-SN

Notes: 1

3 -50 to 100 275 -46 to 38 19

200 235 50 18.4

4 300 215 100 16.2

or m ay be certified for 316 with chemistry that meets 316L 400 195 150 14.8

3000# FS, A-182-F316/316L (note 7)

Liquids and Vapors - General Process Hydrotes t

Press ure Temp Range Corrosion

Allowance ASME B31.3 -50°F / +600°F -46°C / 316°C 413 psig 28.5 barg Service NONE

ASTM A312-Grade 316/316L ERW (note 8)

150# RF SW (note 2) Unions Bolting (Note 5) Threadolets Sch 80S Smls A-312-TP316/316L Nipples (PE x thd)

Swages (PE x thd) Sch 80S Smls A-403-WP316/316L

(RF(RF Flanges) 1/8” thk, ANSI B16.21, Spiral Wound, 316SS with Graphite Filler, Flexitallic Style CG or equivalent Couplings Weldolets 3000# FS, A-182-F316/316L Sch 80S Smls A-312-TP316 Pipe Size Fittings Pipe Flanges

Beveled End (BE)

A-403-WP316/316L, Butt Weld, Welded (100% JE), Bore to match pipe (Notes 3, 8) ASTM A-403-WP316/316L, Butt Weld, Seamless ,

Bore to match pipe (Notes 3, 8)

150# RFWN (note 2) ASTM A-182-F316/316L

ASTM A-312-TP316/316L

3000# FS, A-182-F316/316L (note 7)

Temp / Pres sure Ratings 100°F pres sure rating is used to determine the required pipe wall thicknes s.

V A L V E S

HEADER SIZE Seamless pipe and weld fittings may be s ubstituted for ERW pipe and weld fittings.

B R A N C H S IZ E

Welded cons truction to be used for in-line process piping. Threaded connections are permitted for D2Z-SN, D2ZF-SN, D2S-SN, D2SF-SN,

D2X-SN, D2XF-SN

Where materials are s hown to be dual certified, materials may be s upplied dual certified for 316/316L Us e FF flange for connection to equipment with FF connections

Valves are s uitable for -50°F service temperature.

Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values Refer to P&ID's and/or Equipm ent Data Sheets for sys tem upper lim it des ign tem perature. Plugs 6000# FS, Hex Head, Thd, A-182-F316

Sockolets

(FF Flanges) 1/16” thk, ANSI B16.21, Full-Faced, Synthetic Compres sed Fiber with Nitrile Binder, Klinger C4401 or equivalent Gaskets

Swages (thd x thd)

3000# FS, A-182-F316/316L

Not required unless pipe is externally coated. If provided, washers are to be 316 stainless s teel

A-182-F316/316L, bore to match branch piping Sch 80S Smls A-403-WP316

Nipples (thd x thd)

Bolts / Cap Screws, Alloy Steel, A-193-B8 Rating

ASME CLASS 150

Piping Code Material / Group

Type 316 (2.2) (note 4)

PIPING SPECIFICATION - ASME CLASS 150 - 316/316L SS (NACE) Specification

Document No

Date Des cription 20-Dec-2013

A04N

Cameron Standard - Is sued for Des ign 5-Mar-2014

(15)

Revis ion Prepared Checked Approved 0 SR OB GD 1 SR SB GD 1/2" 3/4" 1" 1-1/2" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" Sch Ends Matl Sch Rating Matl Gate (4) Ball (4,5) Globe (4) Check (4) B utterfly (5) Needle / Gauge Notes : 1

2 Temp °F PSIG Tem p °C BAR

3 -20 to 100 290 -29 to 38 20 200 260 50 19.5 4 300 230 100 17.7 5 400 200 150 15.8 500 170 200 13.8 6 600 140 250 12.1 7 300 10.2 325 9.3 24 20 18 16 14 12 10 8 6 4 3 2 1 1/2 1 3/4 1/2 24 WT 20 WRT WT 18 WRT WRT WT 16 WRT WRT WRT WT 14 WRT WRT WRT WRT WT 12 WRT WRT WRT WRT WRT WT 10 WOL WRT WRT WRT WRT WRT WT

Pipe

Seam less , ASTM A-790-UNS S31803

Service

ASME CLASS 150 ASME B31.3 Ferritic / Austenitic (2.8) None Date

Flanges

150# RF SW 150# RFWN ASTM A-182-F51 -20°F / +400°F -29°C / +204°C 435 ps ig 30 barg

PIPING SPECIFICATION - ASME CLASS 150, 2205 DUPLEX STAINLESS STEEL Specification

A06

Document No

Liquids and Vapors - General Proces s Rating Piping Code Material / Group Tem p Range Corros ion

Allowance

Hydrotes t Press ure

Pipe Size

Fittings 3000# FS, A-182-F51 (Note 7) Seam les s , ASTM A-815-UNS S31803 Clas s WP-S, Butt Weld, Bore to m atch pipe (Note 3) Unions 3000# FS, SW, A-182-F51 (Note 7)

Plugs 6000# FS, Hex Head, threaded, Plated, A-182-F51 Couplings 3000# FS, Full, Threaded, A-182-F51 Nipples (thd x thd) Sch 80S Smls , A-790-UNS S31803 Nipples (PE x thd) Sch 80S Smls , A-790-UNS S31803

Swages (thd x thd) Sch 80S, Smls , A-790-UNS S31803 or A-815-UNS S31803 Clas s WP-S Swages (PE x thd) Sch 80S, Smls , A-790-UNS S31803 or A-815-UNS S31803 Clas s WP-S

Swages (PE both ends ) Sch 80S, Smls , A-790-UNS S31803 or A-815-UNS S31803 Clas s WP-S Sockolets 3000# FS, A-182-F51 Threadolets 3000# FS, A-182-F51

Weldolets A-182-F51, bore to match branch piping

B R A N C H S IZ E HEADER SIZE Not applicable

Welded construction to be us ed for in-line process piping. Threaded connections are perm itted for ins trum ent take-offs , piping vent and drain valves

Butt weld reducing fittings s hall be purchas ed to the heavier pipe s chedule. Piping drawing notes will indicate where internal beveling is required

Gas kets (RF Flanges ) 1/8” thk, ANSI B16.21, Spiral Wound, 316SS, Graphite Filler, SS outer ring, Flexitallic CG or equivalent

Bolting

Bolts / Cap Screws , Alloy Steel, A-193-B7, Fluorocote No. 1 finis h Nuts, Alloy Steel, s em i-finis hed, A-194-2H, Fluorocote No. 1 finish Was hers, s teel, F436, Fluorocote No. 1 finis h

V A L V E S D1Z-X, D1S-X, D1X-X A1R-X D2Z-X, D2ZF-X, D2X-X, D2XF-X, D2S-X, D2SF-X A2R-X, A2RF-X D4Z-X, D4S-X A4R-X

D5Z-X, D5S-X A5R-X, A5RG-X, A5RW-X

20-Dec-2013 Cam eron s tandard - Iss ued for Des ign Des cription

5-Mar-2014 Revis e Pipe Sch, Nipples , Swages

Duplex stainles s s teel body valves m ay be forged or cas tings

Valves with elastom er s eats and/or s eals may not be rated for full ANSI pres s ure-temperature values . Refer to P&ID's and/or Equipm ent Data Sheets for s ys tem upper lim it design tem perature.

-20 / 100°F press ure rating is us ed to determ ine the required pipe wall thicknes s. Not applicable

Tem p / Pres s ure Ratings A7RG-X, A7RW-X

(16)

3 -20 to 100 290 -29 to 38 20 200 260 50 19.5 4 300 230 100 17.7 5 400 200 150 15.8 500 170 200 13.8 6 600 140 250 12.1 7 300 10.2 325 9.3 24 20 18 16 14 12 10 8 6 4 3 2 1 1/2 1 3/4 1/2 24 WT 20 WRT WT 18 WRT WRT WT 16 WRT WRT WRT WT 14 WRT WRT WRT WRT WT 12 WRT WRT WRT WRT WRT WT 10 WOL WRT WRT WRT WRT WRT WT

5-Mar-2014 Revis e Pipe Sch, Nipples , Swages

Welded cons truction to be used for in-line process piping. Threaded connections are permitted for instrument take-offs, piping vent and drain valves

Tem p / Pressure Ratings Not applicable

Butt weld reducing fittings shall be purchased to the heavier pipe schedule. Piping drawing notes will indicate where internal beveling is required

A7RG-XN, A7RW-XN

G6S-XN, G9S-XN

Ferritic / Austenitic (2.8) None

Sch 80S Sch 40S Sch 10S B R A N C H S IZ E HEADER SIZE

Cameron standard - Issued for Design

Duplex stainles s steel body valves may be forged or castings

Valves with elas tomer seats and/or seals may not be rated for full ANSI pressure-tem perature values . Refer to P&ID's and/or Equipment Data Sheets for s ystem upper limit design tem perature.

Not applicable

-20 / 100°F pres sure rating is us ed to determine the required pipe wall thickness.

Gaskets (RF Flanges) 1/8” thk, ANSI B16.21, Spiral Wound, 316SS, Graphite Filler, SS outer ring, Flexitallic CG or equivalent

Bolting

Bolts / Cap Screws , Alloy Steel, A-193-B7, Fluorocote No. 1 finish Nuts, Alloy Steel, semi-finished, A-194-2H, Fluorocote No. 1 finish Washers , steel, F436, Fluorocote No. 1 finish

V A L V E S D1Z-XN, D1S-XN, D1X-XN A1R-XN D2Z-XN, D2ZF-XN, D2X-XN, D2XF-XN, D2S-XN, D2SF-XN A2R-XN, A2RF-XN D4Z-XN, D4S-XN A4R-XN

D5Z-XN, D5S-XN A5R-XN, A5RG-XN, A5RW-XN Sockolets 3000# FS, A-182-F51

Threadolets 3000# FS, A-182-F51

Weldolets A-182-F51, bore to m atch branch piping Swages (thd x thd) Sch 80S, Smls, A-790-UNS S31803 or A-815-UNS S31803 Class WP-S Swages (PE x thd) Sch 80S, Smls, A-790-UNS S31803 or A-815-UNS S31803 Class WP-S

Swages (PE both ends)

Sch 80S, Sm ls A-790-UNS S31803 or A-815-UNS S31803 Class WP-S Couplings 3000# FS, Full, Threaded, A-182-F51 Nipples (thd x thd) Sch 80S Smls , A-790-UNS S31803 Nipples (PE x thd) Sch 80S Smls , A-790-UNS S31803

Fittings 3000# FS, A-182-F51 (Note 7) Seam less, ASTM A-815-UNS S31803 Class WP-S, Butt Weld, Bore to m atch pipe (Note 3) Unions 3000# FS, SW, A-182-F51 (Note 7)

Plugs 6000# FS, Hex Head, threaded, Plated, A-182-F51 Flanges

150# RF SW 150# RFWN ASTM A-182-F51 -20°F / +400°F -29°C /204°C 435 psig 30 barg

PIPING SPECIFICATION - ASME CLASS 150, 2205 DUPLEX STAINLESS STEEL (NACE) Specification

A06N

Document No

Liquids and Vapors - General Proces s Rating Piping Code Material / Group Tem p Range Corrosion

Allowance Hydrotest Pressure Date 20-Dec-2013 Pipe Size Pipe

Seam less, ASTM A-790-UNS S31803

Service

ASME CLASS 150 ASME B31.3

(17)

Revision Prepared Checked Approved 0 SR OB GD 1 SR SB GD 1/2" 3/4" 1" 1-1/2" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" Sch Ends Matl Sch Rating Matl Gate (4) Ball (4,5) Globe (4) Check (4) B utterfly (5) Needle Notes: 1

2

Temp °F

PSIG Temp °C

BAR

3

-20 to 100

290 -29 to 38

20

200

260

50

19.5

4

300

230

100

17.7

5

400

200

150

15.8

500

170

200

13.8

6

600

140

250

12.1

7

300

10.2

8

325

9.3

PIPING SPECIFICATION - ASME CLASS 150, 2507, SUPER DUPLEX STAINLESS STEEL Specification

A08

Document No

Date Description

20-Dec-2013 Cam eron standard - Issued for Design 5-Mar-2014 Revise Pipe Sch, Nipples , Swages

Service

ASME 150 ASME B31.3 Ferritic / Austenitic (2.8) None Liquids and Vapors - General Process Rating Piping Code Material / Group Tem p Range Corrosion

Allowance

Hydrotest Pres sure

Flanges

ASTM A-182-F53 Pipe Size

Pipe Plain End (PE) Beveled End (BE)

Seam les s, ASTM A-790-UNS S32750

Plugs 6000# FS, Hex Head, threaded, Plated, A-182-F53 Couplings 3000# FS, Full, Threaded, A-182-F53

Fittings 3000# FS, A-182-F53 (Note 8) Seam less, ASTM A-815-UNS S32750 Clas s WP-S, Butt Weld, Bore to m atch pipe (Note 3) Unions 3000# FS, SW, A-182-F53 (Note 8)

Swages (thd x thd) Sch 80S, Sm ls, A-790-UNS S32750 or A-815-UNS S32750 Class WP-S Swages (PE x thd) Sch 80S, Sm ls, A-790-UNS S32750 or A-815-UNS S32750 Class WP-S Nipples (thd x thd) Sch 80S Smls , A-790-UNS S32750 Nipples (PE x thd) Sch 80S Smls , A-790-UNS S32750

Threadolets 3000# FS, A-182-F53

Weldolets A-182-F53, bore to m atch branch piping

Swages (PE both ends)

Sch 80S, Sm ls, A-790-UNS S32750 or A-815-UNS S32750 Class WP-S Sockolets 3000# FS, A-182-F53 A1R-D D2R-D, D2S-D, D2SF-D, D2X-D, D2XF-D A2R-D, A2RF-D D4S-D, D4Z-D A4R-D

D5S-D, D5Z-D A5R-D, A5RGXN, A5RW-D

Gaskets (RF Flanges) 1/8” thk, ANSI B16.21, Spiral Wound, 316SS, Graphite Filler, SS outer ring, Flexitallic GC or equivalent

Bolting

Bolts / Cap Screws, Alloy Steel, A-193-B7, Fluorocote No. 1 finish Nuts, Alloy Steel, sem i-finis hed, A-194-2H, Fluorocote No. 1 finish Washers, steel, F436, Fluorocote No. 1 finish

B R A N C H S IZ E HEADER SIZE instrument take-offs, piping vent and drain valves

-20°F / +600°F -29°C / 316°C

435 psig 30 barg

Not applicable

Welded construction to be us ed for in-line proces s piping. Threaded connections are perm itted for s eal m aterials. Refer to P&ID's and/or Equipment Data Sheets for system upper limit design tem perature. Not applicable

Butt weld reducing fittings s hall be purchas ed to the heavier pipe s chedule. Piping drawing notes will indicate where internal beveling is required

A7RG-D, A7RW-D G6S-D, G9S-D

-20 / 100°F press ure rating is us ed to determine the required pipe wall thickness. Tem p / Pressure Ratings Not applicable

Super Duplex SS body valves may be forged or cas tings.

Valves with elastomer seats and/or seals may not be ratedf for full ANSI pres sure-termperature values.

V A L V E S D1S-D, D1X-D, D1Z-D