Areva - p632

P632

Transformer

Differential Protection Device

Version -304 -403/404 -606 ff

Supporting Documents

P632/EN IN/A54

(AFSV.11.09640 EN)

!

Warning

When electrical equipment is in operation dangerous voltage will be present in certain parts of the equipment. Failure to observe warning notices, incorrect use or improper use may endanger personnel and equipment and cause personal injury or physical damage.

Before working in the terminal strip area, the device must be isolated. Where stranded conductors are used, wire end ferrules must be employed.

Proper and safe operation of this device depends on appropriate shipping and handling, proper storage, installation and commissioning, and on careful operation, maintenance and servicing. For this reason only qualified personnel may work on or operate this device.

For this reason only qualified personnel familiar with the content of the Safety Guide (SFTY/4LM/B11 or later version) may work on or operate this device.

Any modifications to this device must be in accordance with the manual.

If any other modification is made without the express permission of AREVA T&D, it will invalidate the warranty, and may render the product unsafe.

Qualified Personnel

are individuals who

† are familiar with the installation, commissioning and operation of the device and of the system to which it is being connected;

† are able to perform switching operations in accordance with safety engineering standards and are authorized to energize and de-energize equipment and to isolate, ground and label it;

† are trained in the care and use of safety apparatus in accordance with safety engineering standards; † are trained in emergency procedures (first aid).

Note

The operating manual for this device gives instructions for its installation, commissioning and operation. However, the manual cannot cover all conceivable circumstances or include detailed information on all topics. In the event of questions or specific problems, do not take any action without proper authorization. Contact the appropriate AREVA technical sales office and request the necessary information.

Any agreements, commitments, and legal relationships and any obligations on the part of AREVA, including settlement of warranties, result solely from the applicable purchase contract, which is not affected by the contents of the operating manual.

Stückprüfbescheinigung P632

Routine Test Certificate P632

AREVA Energietechnik GmbH ist ein DQS zertifiziertes Unternehmen.

Fertigung und Prüfung der Schutzeinrichtungen erfüllen die Anforderungen von DIN EN ISO 9001.

AREVA Energietechnik GmbH has been awarded the DQS certificate by the internationally recognized, independent and impartial association for the certification of quality assurance systems, DQS (Deutsche Gesellschaft zur Zertifizierung von

Qualitätssicherungssystemen), thereby certifying that ALSTOM has introduced and uses a state-of-the-art quality assurance system that complies with all requirements stated in EN ISO 9001 that apply to its products and services.

Stückprüfung

Routine Test

Alle Prüfungen nach IEC 255-6 und DIN EN 60255-6.

All tests according to IEC 255-6 and EN 60255-6.

Die folgenden Überprüfungen waren Gegenstand der Stückprüfung bei Referenzbedingungen:

The following tests have been carried out as part of the routine test under reference conditions:

1 Übereinstimmung der Schutzeinrichtung mit Bestückungs- und Anschlußplan

Conformity of the protection device with components list, location diagram and terminal connection diagram

2 Isolationsprüfung

Insulation test

3 Stromversorgung im Bereich 0,8 UH,nom ≤ UH,nom ≤ 1,1 UH,nom

Power supply within the range 0.8 VA,nom ≤ VA,nom ≤ 1.1 VA,nom

4 Prüfung der Genauigkeit der Einstellwerte

Accuracy of the setting values

5 Ansprech- und Kommandozeiten für alle wesentlichen Funktionen

Operate and command times for all essential functions

6 Funktionsprüfung aller binären Signaleingänge und Kontakte

Functional testing of all binary signal inputs and contacts

7 100 % kontrollierter Wärmedauerlauf

Contents

3.5 Panel Cutout for Case 40 T 18

3.6 Panel Cutout for Case 84 T 20

3.7 Case 40 T, Flush-Mounted 22

3.8 Case 84 T, Flush-Mounted 24

3.9 Combining 40 T Cases to Form a 19“ Mounting Rack 26

3.10 Fitting a 19” Mounting Rack into a Cabinet 27

4 Location Diagrams 28

4.1 Case 40 T, Pin-terminal Connection 28

4.2 Case 84 T, Ring-terminal Connection 29

4.3 Ethernet Module 30

5 Terminal Connection Diagrams 31

5.1 Case 40 T, Pin-terminal Connection 31

5.2 Case 84 T, Ring-terminal Connection 37

1 Order Information

MiCOM P632

Name Order number

Two Winding Transformer Diff. Prot. P 6 3 2 - 9 0 1 -304 -4xx -606 -46x -9x x -95 x -8xx Basic device:

Basic device 40TE, pin-terminal connection, 3 -403 Basic device 84TE, ring-terminal connection, 8 -404 basic complement with 4 binary inputs and 8 output relays

Mounting option and display:

Surface-mounted, local control panel with text display 3 Flush-mounted, local control panel with text display 4 Processor extension and Current transformer:

With DSP-Coprocessor, Inom = 1 A / 5 A (T11...T13 / T21...23) 2) 8 Inom = 1 A / 5 A (T11...T14 / T21...24) 2) ₉

Voltage transformer:

Vnom = 50 ... 130 V (1-pole) 1

Additional binary I/O options:

Without 0

With 1 binary module (add. 6 binary inputs and 8 output relays) 1 Power supply and additional outputs:

VA,nom = 24 VDC 3

VA,nom = 48 ... 250 VDC / 100 ... 230 VAC 4 VA,nom = 24 VDC and 6 output relays, 4 with thyristor 6 VA,nom = 48 ... 250 VDC / 100 ... 230 VAC 7 and 6 output relays, 4 with thyristor

VA,nom = 24 VDC and 6 output relays 8 VA,nom = 48 ... 250 VDC / 100 ... 230 VAC and 6 output relays 9 Further add. options:

Without 0

With analogue module 2

With binary module (add. 24 binary inputs) 4 Switching threshold on binary inputs:

>18 V (standard variant) (Without order extension no.)

>90 V (60...70% of VA,nom = 125...150 V) 8) -461

>155 V (60...70% of VA,nom = 220...250 V) 8) _-462

>73 V (67% of VA,nom = 110 V) 8) -463

>146 V (67% of VA,nom = 220 V) 8) _-464

With communication / information interface:

Only IRIG-B input for clock synchronization -90 0

Protocol IEC 60870-5-103 -91

Protocol can be switched between: -92

IEC 60870-5-101/-103, Modbus, DNP3, Courier and IRIG-B input for clock synchronization and 2nd interface (RS485, IEC 60870-5-103)

For connection to wire, RS485, isolated 1

For connection to plastic fibre, FSMA connector 2

For connection to glass fibre, ST connector 4

Protocol UCA2 -93

For connection to 10 MHz Ethernet, glass fibre ST and wire RJ45 5 and 2nd interface (RS485, IEC 60870-5-103)

For connection to 100 MHz Ethernet, glass fibre SC and wire RJ45 6 and 2nd interface (RS485, IEC 60870-5-103)

Language:

English (German) 4) (Without order extension no.)

Px40 English (English) 4) _{(On request) -800}

German (English) 4) -801

French (English) 4) _{(On request) -802}

Spanish (English) 4) (On request) -803

Polish (English) 4) _{(On request) -804}

Russian (English) 4) 7) (On request) -805

2) Switching via parameter, default setting is underlined! 4) Second included language in brackets

7) Hardware option, supports cyrillic letters instead of special West. Europe characters

8) Standard variant recommended, if higher pickup threshold not explicitly required by the application

2 Modifications

2 Modifications

The following area is reserved for documentation of design version modifications of this device, e.g. add-ons, by the factory or the user. It contains information on modification date and modifying person.

3 Dimensional Drawings 3.1 Surface-Mounted Case 40 T

1 Dimensional drawing for surface-mounted case 40 T (dimensions in mm)

3 Dimensional Drawings

(continued)

3.2 Flush-Mounted Case 40 T

(continued)

3 Dimensional drawing for flush-mounted case 40 T, flush-mount method 2 (using the angle brackets and frame) (dimensions in mm)

3 Dimensional Drawings

(continued)

3.3 Flush-Mounted Case 84 T

(continued)

5 Dimensional drawing for flush-mounted case 84 T, flush-mount method 2 (using the angle brackets and frame) (dimensions in mm)

3 Dimensional Drawings

(continued)

3.4 Protective Conductor Terminal (PCT) / Case Grounding / Protective Earth Terminal

19Y5220A_EN

6 Mounting the PCT / Mounting set for case grounding

PCT: Protective Conductor Terminal, formerly "Protective Earth Terminal" The clamp bracket is marked with a PCT symbol:

(continued)

3.5 Panel Cutout for Case 40 T

7 Dimensional drawing of panel cutout for case 40 T, flush-mount method 1 (without angle brackets and frame) (dimensions in mm)

3 Dimensional Drawings

(continued)

(continued)

3.6 Panel Cutout for Case 84 T

9 Dimensional drawing of panel cutout for case 84 T, flush-mount method 1 (without angle brackets and frame) (dimensions in mm)

3 Dimensional Drawings

(continued)

(continued)

3.7 Case 40 T, Flush-Mounted

11 Installation of case 40 T for flush-mounting, flush-mount method 1 (without angle brackets and frame) Protective Conductor Terminal (PCT) / Case Grounding / Protective Earth Terminal: See Chapter 3.4

3 Dimensional Drawings

(continued)

12 Installation of case 40 T for flush-mounting, flush-mount method 2 (using the angle brackets and frame) Protective Conductor Terminal (PCT) / Case Grounding / Protective Earth Terminal: See Chapter 3.4

(continued)

3.8 Case 84 T, Flush-Mounted

13 Installation of case 84 T for flush-mounting, flush-mount method 1 (without angle brackets and frame) Protective Conductor Terminal (PCT) / Case Grounding / Protective Earth Terminal: See Chapter 3.4

3 Dimensional Drawings

(continued)

14 Installation of case 84 T for flush-mounting, flush-mount method 2 (using the angle brackets and frame) Protective Conductor Terminal (PCT) / Case Grounding / Protective Earth Terminal: See Chapter 3.4

(continued)

3.9 Combining 40 T Cases to Form a 19” Mounting Rack

15 Combining 40 T flush-mounting cases to form a 19” mounting rack

Protective Conductor Terminal (PCT) / Case Grounding / Protective Earth Terminal: See Chapter 3.4

3 Dimensional Drawings

(continued)

3.10 Fitting a 19” Mounting Rack into a Cabinet

16 Fitting a 19” mounting rack

4 Location Diagrams

4.1 Case 40 T, Pin-terminal Connection

17 Location diagram P632 in case 40 T, pin-terminal connection Location diagram of the Ethernet module see Chapter 4.3

4 Location Diagrams

(Fortsetzung)

(continued)

30 P632-304-403/404-606 // P632/EN IN/A54 // AFSV.11.09640 EN

4.3 Ethernet Module Type -X 1 0 Type A * Px3x_Ethernet_01A_EN A Designation Communication module Item

-U17; -U18; -U20; -U25; -U26 Slot

02 01 02

01

* : Alternative module (see order information) 02 -X 7 * -X 8 * -X 13 * -X 1 2

19 Location diagram of the Ethernet module applicable to:

Case 40 T, pin-terminal connection Case 84 T, ring-terminal connection

5 Terminal Connection Diagrams

5 Terminal Connection Diagrams 5.1 Case 40 T, Pin-terminal Connection

(continued)

21 Terminal connection diagram P632 in case 40 T, pin-terminal connection, diagram P632.403, part 2 of 6

5 Terminal Connection Diagrams

(continued)

23 Terminal connection diagram P632 in case 40 T, pin-terminal connection, diagram P632.403, part 4 of 6

5 Terminal Connection Diagrams

(continued)

25 Terminal connection diagram P632 in case 40 T, pin-terminal connection, diagram P632.403, part 6 of 6 Terminal connection diagram of the Ethernet module see chapter 5.3

5 Terminal Connection Diagrams

(continued)

(continued)

27 Terminal connection diagram P632 in case 84 T, ring-terminal connection, diagram P632.404, part 2 of 6

5 Terminal Connection Diagrams

(continued)

29 Terminal connection diagram P632 in case 84 T, ring-terminal connection, diagram P632.404, part 4 of 6

5 Terminal Connection Diagrams

(continued)

31 Terminal connection diagram P632 in case 84 T, ring-terminal connection, diagram P632.404, part 6 of 6 Terminal connection diagram of the Ethernet module see chapter 5.3

5 Terminal Connection Diagrams

STATUS -X8 * STATUS -X13 * STATUS -X12 * STATUS + -+ -+ -Comm. fiber interface Ethernet (10 Base - FL)

Comm. fiber interface Ethernet (10 Base - FL)

Comm. fiber interface Ethernet (100 Base - FX)

Comm. interface Ethernet (10 Base T / 100 Base TX) LOCATION ITEM DESIGN. CONNECTOR MEANING ITEM REFER. REFER. LOCATION ITEM DESIGN. CONNECTOR MEANING ITEM REFER. REFER. LOCATION ITEM DESIGN. CONNECTOR MEANING ITEM REFER. REFER. LOCATION ITEM DESIGN. CONNECTOR MEANING ITEM REFER. REFER. X / Y RX X / Y TX -U17 -U18 ST ST -+ RS 485 1 2 3 4 5 -U20 -+ X // Y D2[R] D1[T] X / Y RX TX -U26 SC X // Y 1 -U25 RJ45 -X10 * STATUS + -Comm. interface Channel 2 LOCATION ITEM DESIGN. CONNECTOR MEANING ITEM REFER. REFER.

TRANSMISSION & DISTRIBUTION Energy Automation & Information [email protected] www.areva.com P u bl icati o n : P6 32-304-403/404 -606 // P632/E N IN /A 54 // A F SV.11. 09640 E