C5 Config BSI

(1)

CITROËN

INFO’ DIAG

DIAGNOSTIC TOOLS

LEXIA

PROXIA

CD 41

AFTER SALES

DIVISION

CITROËN SELLING DEALERS:

- PDI

technicians

- Campaign

co-ordinators

AUTHORISED REPAIRERS:

- Service

Managers

-

Consultant technicians

N° 421

19/12/2008

THE CONTENTS OF THIS BULLETIN SHOULD BE MADE KNOWN TO ALL PERSONNEL WHO, DIRECTLY OR INDIRECTLY, USE LEXIA / PROXIA DIAGNOSTIC TOOLS.

TITLE:

Manual configuration of the BSI ECU on CITROËN C5 (X7).

CONCERNING:

The operations for configuring a BSI ECU:

• Following the replacement of an ECU,

• Following the downloading of an ECU,

• Checking the configuration.

IMPORTANT:

Incorrect configuration will affect the operation of the vehicle. Follow the internet

configuration procedure described in this document and limit the use of manual

configuration just to the cases quoted in the INFO'DIAG.

(2)

1 Introduction………...………..3

2 Preliminaries………...………3

2.1 Safety advice……….3

2.2 Technical advice……….…..………..3

3 Operations to be carried out…………...………….…...………....4

3.1 Operations to be carried out before removal, downloading or

configuration of the BSI………...5

3.2 Operations to be carried out to configure the BSI………..6

3.3 Operations to be carried out after the configuration of the BSI…………8

4 Checking of configuration………..9

4.1 Notes on the configuration tables………....………..10

4.2 Configuration menus……….10

4.3 Customer options……….………..11

4.4 Configuration……….………..12

4.5 ECUs present……….……….29

(3)

1 INTRODUCTION

Configuration is a sensitive operation, which has direct consequences on the correct

operation of the vehicle. Incorrect configuration can have an impact on:

• Safety (deactivation of vehicle protection devices),

• Overall functioning of the vehicle (complete loss of or damage to vehicle functions)

• Vehicle diagnostics (returning of fault codes which may cause the diagnostic tool

methods to fail, and lead to the unjustified removal of parts).

You are therefore requested to perform the configuration operation following the

instructions on this INFO’DIAG in order to ensure customer satisfaction by returning

their vehicle in a perfect operational state.

2 PRELIMINARIES

The instructions below must be followed to guarantee safety linked to vehicle operation

and well-being.

2.1 Safety advice

Before starting the engine:

• Check that the electronic parking brake is activated,

• If the gearbox is automatic, check that the gear lever is in position «P » (Park),

• If the gearbox is manual, check that the gear lever is in neutral.

2.2 Technical advice

The BSI must be correctly configured before initialising the BSI, initialising the keys or

starting the engine.

(4)

3 OPERATIONS TO BE CARRIED OUT

This chapter describes the steps to be followed to configure a BSI.

• If the configuration is being carried out following the replacement of a BSI, or

following the downloading of the BSI: follow chapters 3.1, 3.2 and 3.3.

• If the configuration is being carried out independently of a BSI replacement, or the

downloading of a BSI (checking the correct configuration of a vehicle for example):

follow chapters 3.1 and 3.2 only.

Chapter 3.1

Operation to be carried out before removal, downloading or configuration of the BSI:

Printing of customer options configuration values

È

Chapter 3.2

Operations to be carried out to configure the BSI:

È

A) Configuration by internet

È

B) Choice of maintenance plan

È

C) Manual configuration of customer options

È

D) Checking of certain parameters with manual configuration

È

Chapter 3.3

Operations to be carried out after the configuration of the BSI:

Initialisation of BSI (or initialisation of keys or

(5)

3.1 Operations to be carried out before removal, downloading or configuration of

BSI

Before removing the faulty BSI ECU, or downloading or configuring the ECU, establish

communication with this ECU on the vehicle using the LEXIA or PROXIA diagnostic

tool.

Print the screen « Customer Options » from the diagnostic tool, showing the

configuration parameter values (or note these values down manually).

To do so, carry out the following operations:

LEXIA or PROXIA

1 Connect the diagnostic tool on the vehicle.

2 Select "Diagnosis"

3 Enter the vehicle details, then its RPO number

4 Start the "Global Test"

5 Select the menu « BSI », then validate using key « * ».

6 Select the item « Configuration ».

7 Select the item « Manual configuration ».

8 Select the menu « CUSTOMER OPTIONS ».

9 Print the diagnostic tool screen showing the configuration parameter values, or note down these values by hand

10 Return to the Global Test by successive presses on the « Return » key.

Once this operation has been completed, you may replace or download the BSI, if

required to do so.

(6)

3.2 Operations to be carried out to configure the BSI

A) Configuration by internet

LEXIA PROXIA

11 Select the menu « BSI », then validate using key « * ».

13 Select the item « Configuration by internet ».

14

Once the configuration parameters screen has appeared, validate

using key « * ».

The list of configuration menus appears. Validate using key « F5 » to launch configuration by

internet.

15 Check the accuracy of the vehicle’s VIN, then validate using key « * ».

16

To allow an internet connection, make the connections indicated on

the diagnostic tool then validate using key « * » to start configuration by internet.

Once the tool has received the configuration data, return to the Proxia tool by validating with the « return » key.

17

The list of configuration parameters appears. Validate using the key « * »

Successively select the menus: - « CONFIGURATION », - « ECUs PRESENT », - « VIN code ».

In the « CONFIGURATION » menu, select the sub-menus:

- « Vehicle definition – Equipment – Driving information », - « Air conditioning – Cabin heating»,

- « Lighting – Signalling – Visibility – Rear view mirrors », - « Locking – Doors and tailgate – Immobiliser –

Alarm »,

- « Fuel gauge law – Oil level gauge law ».

In each sub-menu and in the ECUs present menu, validate using the « F5 » key to configure the parameters returned by the tool.

18 Return to the main menu of the BSI (« identification », « fault reading », etc.) with successive presses on the « return » key.

NOTE:

If the configuration by internet does not work (presence of a message on the tool

showing the error code linked to the phrase « it is pointless to repeat the operation »),

carry out a manual configuration by replacing the internet configuration (based on the

configuration tables in chapter 0), before continuing with the INFO’DIAG procedure from

section B)

.

NOTE:

A monitoring of configuration failures is carried out centrally to correct any configuration

malfunctions by internet.

(7)

B) Choice of maintenance plan

19

Switch on the ignition. Select the item « Maintenance – Operational mode of BSI »,

then validate with key « * ».

Select the item « Maintenance – Operational mode of BSI »,

then validate with key « * ». 20 Select the item « Maintenance », then validate with key « * ». 21 Select the item « Choice of maintenance plan (new vehicle preparation) ».

22 Follow the instructions given by the diagnostic tool:

reply to the questions asked by the diagnostic tool. 23

Once the choice of maintenance plan procedure has been carried out, return to the main menu of the BSI (« identification », « fault reading »…) with successive presses on the

« return » key.

C) Manual configuration of customer options

Manually configure the «customer options » parameters, using the print-outs or notes

previously made (chapter 3.1).

LEXIA or PROXIA

25 Select the item « Manual configuration ».

26 Select the « CUSTOMER OPTIONS » menu.

27 Check (and modify if necessary), the values of each parameter, according to the values on the print-outs or notes.

28 Return to the main menu of the BSI (« identification », « fault reading », etc.) _{with successive presses on the « return » key.}

D) Checking of certain parameters with manual configuration

It is necessary to check certain configuration parameters (since the central base

providing vehicle data may not be completely up to date). The parameters to check

manually are shaded in grey in chapter 4.

LEXIA or PROXIA

29

Successively select the « CONFIGURATION », « ECUs PRESENT », and « VIN code » menus. In the « CONFIGURATION » menu select the sub-menus:

- « Vehicle definition – Equipment – Driving information », - « Air conditioning – Cabin heating»,

- « Lighting – Signalling – Visibility – Rear view mirrors », - « Locking – Doors and tailgate – Immobiliser – Alarm », - « Fuel gauge law – Oil level gauge law ».

30 In each sub-menu and in the « ECUs present » and « VIN code » menus, check (and modify if _{necessary), the parameter values shaded in grey in the configuration tables (see chapter 4)} 31 Return to the Global Test with successive presses on the « Return » key.

(8)

3.3 Operations to be carried out after the configuration of the BSI

Operations to be carried out only if replacing or downloading a BSI:

• If the BSI has been replaced: initialise the new BSI ECU on the vehicle (« BSI

initialisation »).

• If the BSI has been downloaded, initialise the BSI ECU (« BSI initialisation »), or the

keys, or simply synchronise the high frequency remote controls, depending on what

is indicated in the procedure accompanying the recall campaign.

To carry out the initialisation operations, ALL of the customer’s keys and the confidential

code card are required.

32 Select the item « BSI », then validate using key « * ».

33 Select the item « Initialisation ».

34 Select the « BSI Initialisation » menu _{(or « Initialisation of keys »).} Select the « BSI Initialisation » menu (or _{« Initialisation of keys »).}

35 Validate using key « * ».

36 Follow the instructions given by the diagnostic tool screens, in particular those displayed in the band at the bottom of the screen.

37 Return to the main menu of the BSI (« identification », « fault reading », etc.) _{with successive presses on the « return » key.}

Once steps n° 32 to n° 37 have been completed, carry out the following operations to

check that the vehicle is able to start.

38 Select the item « BSI », then validate using key « * ».

39 Select the « Parameter Measures » menu of the BSI.

40 Select the sub-menu « Immobiliser ».

Select the item « pre-defined parameter screens », then select the sub-menu

« Immobiliser ».

41 Check that the parameter « BSI matched to engine ECU » has the value « Yes ». 42 Check that the parameter « Engine ECU locked » has the value « No ».

43 Check that the parameter « Number of keys initialised » has the value « xx », where « xx » _{corresponds to the total number of the customer’s vehicle keys.} 44 For each key, check that the parameter « Transponder label recognised » has the value _{« Yes ».} 45 Return to the main menus screen of the tool (« diagnosis », « downloading», etc.) with

(9)

4 CHECKING OF THE CONFIGURATION

4.1 Notes on the configuration tables

The display of configuration parameters is conditional on their being present in the BSI

software.

The parameters will be displayed by the diagnostic tool partially or totally depending on

the BSI software version.

An underlined configuration value corresponds to the value to be programmed on all the

vehicles.

Configuration notes:

(1):

Means that you have to programme the parameter according to the absence or

presence of the option or to the vehicle definition. If the option or the vehicle definition is

easily identifiable, the instruction is not accompanied by any particular text.

(2):

Means that you have to programme the value indicated in the column « Value to be

configured ». This value is valid for all vehicles. It is prohibited to programme any

other value.

(3):

Means that this parameter is programmed automatically when you use the

(10)

4.2 Configuration menus

After you have selected the menu « Manual configuration », the following menus are

available:

Menus Pages Customer options 11 Configuration 12 ECUs present 29 VIN code 31

NOTE:

The parameters of the « Customer options » menu are also present in the configuration

menu, it is therefore not necessary to configure these if the configuration of the

parameters of the « Configuration » menu have been or will be carried out.

(11)

4.3 Customer Options

Configuration parameter Values to be

configured Comments

No Driver's door control pad with screenprinted

button .

Multiplexed folding electric rear view mirrors

Yes Driver's door control pad with screenprinted

button .

Presence of rear screen wiping in reverse gear

Absent

Present Configure Present if a rear wiper is fitted. Absent With rubber wheel valves.

Type of deflation detection _{Direct without}

display of pressures With metallic wheel valves. No daytime-running

lamps Type of daytime-running lamps

Dedicated daytime-running lamps

(1)

No

Value not to be configured except on the express request of the customer (deactivation of the alert for detection of driver’s seat belt not fastened). Detection of driver's seat belt not

fastened

Yes (2) No

For all vehicles with the exception of vehicles destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland) Lighting by default of

daytime-running lamps

Yes

For all vehicles destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)

No

For all vehicles with the exception of vehicles destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland) Simultaneous lighting of

daytime-running lamps and sidelamps

Yes

(12)

4.4 Configuration

Once the « Configuration » menu is selected, the following screen appears.

Menus Contents Pages

A VEHICLE DEFINITION – EQUIPMENT –

DRIVER’S INFORMATION 13

B AIR CONDITIONING – CABIN HEATING 20

C LIGHTING – SIGNALLING – VISIBILITY – REAR VIEW MIRRORS 23

D LOCKING – DOORS AND TAILGATE – IMMOBILISER – ALARM 26

E FUEL GAUGE LAW - OIL GAUGE LAW 28

(13)

Key:

Parameter to be systematically checked after configuring by internet

4.4.1 Menu: vehicle definition – equipment – driving information (menu A)

Configuration parameter (A)

Value to be

Absent

All countries other than:

Saudi Arabia, Bahrain, United Arab Emirates, Kuwait, Oman, Qatar.

Overspeed alert for the Arabian peninsula

Present Countries Saudi Arabia, Bahrain, United Arab _{Emirates, Kuwait, Oman, Qatar.} Passenger’s seat

position memorisation control unit option

Absent (2) Automatic gearbox option Absent Present (1) Right-hand-drive vehicle No Yes (1) Variable damping suspension option Absent Present

Configure « present » for vehicles fitted with hydropneumatic suspension with 3.0L petrol (XFV)

or 2.7 L diesel (UHZ) engine.

Absent For engines: • 1.8 L petrol (6FY), • 2.0 L petrol (RFJ), • 2.2 L diesel (4HP, 4HT). Engine oil temperature sensor option Present

For engines:

•

3.0 L petrol (XFV), • 1.6 L diesel (9HZ), • 2.0 L diesel (RHR), • 2.7 L diesel (UHZ).

Absent • Without audio equipment,

• RD4 radio/CD/MP3. Presence of the

telematic unit

(RT3/RT4) _Present • Telematic unit (RT4/RT5), _{• Telematic unit (NG4),} • Radio navigation (RNEG). Presence of

water-in-diesel-fuel sensor

Absent Present

(1) The presence of the sensor for detecting water in the diesel fuel filter is visible thanks to the blue 3-way connector on the diesel fuel filter.

Presence of air pump Absent (2)

Multifunction screen

(14)

Key:

Value to be

Origin of the water-in-diesel-fuel

information

Engine ECU (2)

Absent Driver's seat with manual adjustment. Driving position

memorisation option _Present _{Driver's seat with electric adjustment and memory.} Presence of a trailer

relay unit (BSR)

No

Yes Depending on the presence of a towbar. Presence and type of

vehicle cruise control

Cruise control and speed limiter (2) Engine ECU For engines: • 1.8 L petrol (6FY), • 2.0 L petrol (RFJ), • 2.2 L diesel (4HP, 4HT). Origin of the oil

temperature information

Engine Relay Unit

For engines:

• 3.0 L petrol (XFV), • 1.6 L diesel (9HZ), • 2.0 L diesel (RHR), • 2.7 L diesel (UHZ). Presence of a parking assistance button No Yes

Depending on the presence of the button (or the presence of sensors on the bumpers, front and rear) Absent Without ultra-sonic sensors on the bumpers.

Rear With 4 ultra-sonic sensors on the rear bumper only. Type of parking

assistance Front and rear and available parking

space

With 4 ultra-sonic sensors on the front and rear bumpers. Parking assistance with visual information No Yes

Depending on the absence or presence of ultra-sonic sensors on the rear bumper.

Parking assistance with sound information

No Yes

Depending on the absence or presence of ultra-sonic sensors on the rear bumper.

Absent With rubber wheel valves. Type of deflation

detection _{Direct without}

display of pressures With metallic wheel valves. No detection If particle filter absent. Type of detection of

presence of fuel cap _{By the BSI} _{If particle filter present.} Piloting of the diesel No particle filter If particle filter absent.

(15)

Key:

Value to be

fuel additive pump _{Control by wire} _{If particle filter present.}

Standard For vehicles except those fitted with a 2.0 L petrol (RHR) or 1.8 L petrol (6FY) engine.

Type of alternator

Controlled For vehicles fitted with a 2.0 L petrol (RHR) or 1.8 L _{petrol (6FY) engine.} Presence of available parking space button No Yes (1) Presence of available parking space warning lamp

No (2)

Total time before

next maintenance 12 or 24 months (3)

12 months for « severe » use of the vehicle. 24 months for « normal » use of the vehicle. 0 km

Configure 0 km for vehicles with an RPO number ≥ 11480 (14th April 2008) or for vehicles which have had their first service.

Threshold for first service

2500 km

Configure 2500 km for vehicles with an RPO number < 11480 and which have not had their first service.

Speedometers in kilometres - CASE N°1

15 000 km

(3) For severe use and engines: • 2.0 L petrol (RFJ), • 1.6 L diesel (9HZ). Maintenance

threshold (marketing)

20 000 km

(3) For normal use and engines: • 2.0 L petrol (RFJ), • 1.6 L diesel (9HZ). For severe use and engines:

• 1.8 L petrol (6FY), • 3.0 L petrol (XFV), • 2.0 L diesel (RHR), • 2.2 L diesel (4HP, 4HT), • 2.7 L diesel (UHZ).

(16)

Key:

Value to be

30 000 km

(3) For normal use and engines: • 1.8 L petrol (6FY), • 3.0 L petrol (XFV), • 2.0 L diesel (RHR), • 2.2 L diesel (4HP, 4HT), • 2.7 L diesel (UHZ).

Speedometers in miles - CASE N°2

16 000 km

(3) For severe use and engines: • 2.0 L petrol (RFJ), • 1.6 L diesel (9HZ).

20 000 km

(3) For normal use and engines: • 2.0 L petrol (RFJ), • 1.6 L diesel (9HZ). For severe use and engines:

• 1.8 L petrol (6FY), • 3.0 L petrol (XFV), • 2.0 L diesel (RHR), • 2.2 L diesel (4HP, 4HT), • 2.7 L diesel (UHZ). 32 000 km

(3) For normal use and engines: • 1.8 L petrol (6FY), • 3.0 L petrol (XFV), • 2.0 L diesel (RHR), • 2.2 L diesel (4HP, 4HT), • 2.7 L diesel (UHZ). Duration before 1st service 00 months (2) Kilometre threshold for forcing of customer mode 250 km (2) Memorisation of faults Authorised (2) (3) Presence of an electric secondary brake No Yes (1) Electrically

(17)

Key:

Value to be

No With manual adjustment of the height and reach of _{the steering wheel.} Presence of the

welcome function for

the driver _Yes With electrical adjustment of the height and reach of

the steering wheel.

Engine relay unit

(BSM)

For engines:

•

3.0 L petrol (XFV), • 1.6 L diesel (9HZ), • 2.0 L diesel (RHR), • 2.7 L diesel (UHZ).

Origin of the oil

pressure

information

Engine ECU

For engines: • 1.8 L petrol (6FY), • 2.0 L petrol (RFJ), • 2.2 L diesel (4HP, 4HT). Number of switches for non-fastening of seatbelts 5 (2)

Sensor for detection of presence of a front passenger Absent (2) Detection of non-fastening of the driver's seatbelt Yes (2) Detection of

non-fastening of the front passenger’s seat belt

Yes (2) Presence of a radio

RD4

No

Yes (1)

No Mechanical power steering.

Presence of a red warning lamp for the

Steering Assistance

alert Yes Hydraulic power steering.

Presence of an orange warning lamp

for the Steering Assistance alert

Yes

(2)

Tolerance on value set for the cruise control / speed limiter

3 km/h (2) Lane Departure Warning System option Absent Present

(1) Depending on presence of a button for deactivation of the function.

(18)

Key:

Value to be

No All diesel engines except: • 2.7 L diesel (UHZ). Presence of a fuel pump Yes On engines: • Petrol, • 2.7 L diesel (UHZ). Presence of a boot relay unit No (2)

Type of vehicle Saloon

Estate (1) Presence of Head-Up display No (2) Presence of a mobile deflector No (2) Presence of Hands-Free Kit No Yes (1) Presence of CD changer Absent Present (1) Detection of non-fastening of middle rear passenger’s seat belt Yes (2) Detection of non-fastening of rear LH passenger’s seatbelt Yes (2) Detection of non-fastening of rear RH passenger’s seatbelt Yes (2) Presence of an audio equaliser amplifier No Yes

(1) Depending on the presence of a bass box in the boot.

No With radio/CD/MP3/RD4 or telematic unit (RT4, _{RT5, NG4) or radio navigation (RNEG).} Sound alert for

parking assistance emitted by switch

module under

(19)

Key:

Configuration parameter (A) Value to be configured Comments Display of fuel consumption without overconsumption due to regeneration

of the particle filter

No (2)

0.6 s

• All engines except 1.6 L Diesel (9HZ), • 1.6L diesel (9HZ) engine and BSI software

version ≥ 6.30. Time of response by

the engine ECU to the BSI during operation of cruise

control 1.2 s • 1.6L diesel (9HZ) engine and BSI software

version = 5.50. Display of the rear

seat belt fastening alert on opening of a

rear door or switching on the

ignition

Yes (2)

No Handbrake with warning lamp.

Retention of braking (by the ESP) for 2

seconds when

starting on a gradient Yes Electric secondary brake.

Battery charge estimation function Present, performed by the Battery charge status control unit (2) Presence of massaging front seats No Yes (1) No Metal suspension. Presence of a Built-in Hydraulic Interface

(BHI) _{Yes Hydropneumatic}_suspension

No With mechanical power steering.

Presence of power

steering Yes With hydraulic power steering, (presence of an

electro-pump) Presence of services

module

No Yes

(1) Configure « yes » if a telematic unit (NG4) with emergency call button is present.

Presence of a navigation system (NG4) No Yes (1) Presence of a radio RD4 No Yes (1) Presence of Hands-Free Kit No Yes (1)

(20)

Key:

Configuration parameter (A) Value to be configured Comments Presence of CD changer No Yes (1) Presence of massaging front seats No Yes (1)

4.4.2 Menu:

air

conditioning

– cabin heating (menu B)

Configuration parameter (B)

Value to be

No For Mono-zone Automatic Air Conditioning. Presence of the

pollution sensor

Yes

For Bi-zone Automatic Air Conditioning (separate

adjustment of the temperature and air distribution on the left-hand side and right-hand side).

Presence of humidity sensor in

the cabin

No (2)

Mono-zone

sunlight sensor For Mono-zone Automatic Air Conditioning. Type of sunlight

sensor

Bi-zone sunlight sensor

Mono-zone For Mono-zone Automatic Air Conditioning. Type of air mixing

Bi-zone

Mono-zone For Mono-zone Automatic Air Conditioning. Type of air

distribution

Bi-zone

Absent For petrol engines. Heating

elements For a diesel engine without additional heating. Type of additional

heating

Autonomous

(21)

Key:

Configuration parameter (B) Value to be configured Comments Programmable burner

For a diesel engine with programmable additional heating.

1,19 For engines:

• 3 L petrol (engine plate XFV). 1,24

For engines:

• 1.8 L petrol (engine plate 6FY), • 2.0 L petrol (engine plate RFJ).

1.28

For engines:

• 1.6 L diesel (engine plate 9HZ), • 2.0 L diesel (engine plate RHR),

• 2.2 L diesel (engine plate 4HP and 4HT). Aircon compressor

drive ratio

1.34 For engines:

• 2.7 L diesel (engine plate UHZ). Mono-zone For Mono-zone Automatic Air Conditioning. Presence and type

of blown air sensor

Bi-zone

Presence of electric

(22)

Key:

Configuration parameter (B) Value to be configured Comments Temperate (-17°C to +37°C)

For vehicles destined for the following countries,

territories or departments: South Africa, Barbados,

Belgium, Bermuda, Cyprus, Spain, Metropolitan France, United Kingdom, Greece, Grenada, Guadeloupe, Guyana, Ireland, Italy, Jamaica, Luxembourg, Malta, Martinique, Mauritius, New Caledonia, New Zealand, Netherlands, French Polynesia, Portugal, Reunion, St. Martin, St. Lucia, Seychelles, Tahiti, Trinidad & Tobago.

Cold (-25°C to +37°C)

For vehicles destined for the following countries:

Albania, Germany, Austria, Azerbaijan, Bosnia, Bulgaria, Croatia, Denmark, Estonia, Hungary, Iceland, Latvia, Lithuania, Macedonia, Poland, Romania, Serbia-Montenegro, Slovakia, Slovenia, Switzerland, Czech Republic.

Very cold (-30°C to +37°C)

Armenia, Belarus, Finland, Georgia, Kazakhstan, Kirghizistan, Moldavia, Norway, Uzbekistan, Russia, Sweden, Turkmenistan, Ukraine.

Hot (-17°C to +45°C)

Algeria, Angola, Antigua & Barbuda, Argentina, Aruba, Australia, Bahamas, Bangladesh, Benin, Bolivia, Botswana, Brazil, Brunei , Burkina Faso, Burundi,

Cambodia, Cameroon, Cape Verde, Sierra Leone, Chile, Colombia, Comoros, Congo, South Korea, Costa Rica, Ivory Coast, Cuba, Djibouti, Egypt, El Salvador, Ecuador, Ethiopia, Fiji, Gabon, Gambia, Ghana , Guatemala, Guinea, Haiti, Honduras, Hong Kong, India, Indonesia, Iraq, Iran, Israel, Japan, Jordan, Kenya, Laos, Lebanon, Liberia, Libya, Macao, Madagascar, Malaysia, Malawi, Mali, Morocco, Mauritania, Mayotte, Mexico ,

Mozambique, Namibia, Nicaragua, Niger, Nigeria, Uganda, Pakistan, Palestine, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Central African Republic, Dominican Republic, Rwanda, Senegal, Singapore, Somalia, Sudan, Sri Lanka, Surinam, Syria, Tajikistan, Taiwan, Tanzania, Chad, Thailand, Togo, Tonga, Tunisia, Turkey, Myanmar, Uruguay, Venezuela, Vietnam, Yemen, Zambia, Zimbabwe.

Type of climate

Very hot (-17°C to +50°C)

Saudi Arabia, Bahrain, United Arab Emirates, Kuwait, Oman, Qatar.

(23)

Key:

Configuration parameter (B) Value to be configured Comments Presence of heated seats No Yes

Depending on presence or absence of heated seat controls.

Type of aircon pressure sensor

Pressure sensor

30 bars (2)

4.4.3 Menu: lighting – signalling – visibility – rear view mirrors (menu C)

Configuration parameter (C)

Value to be

Sunlight sensor option Absent Present

Configure Present if the vehicle is fitted with a wipers stalk with « auto » position.

Rain sensor option Absent Present

Headlamp wash option Absent

Present (1) Automatic lighting of

instrument panel and multifunction screen depending on external

brightness

Absent (2)

Automatic lighting of hazard warning lamps

in the event of impact Absent (2)

Guide-me-home lighting option

Absent Present

Automatic lighting of hazard warning lamps

under heavy deceleration Present (2) Presence of front foglamps No Yes

(1)

(24)

Key:

Configuration parameter (C)

Value to be

No Driver's door control pad with screenprinted button .

Multiplexed folding electric rear view

mirrors _Yes Driver's door control pad with screenprinted button .

No Rear view mirrors

indexed to reverse

gear _Yes

Depending on whether the rear view mirrors are equipped with electric folding or not.

Presence of rear screen wiping in

reverse gear

Absent

Present Configure Present if a rear wiper is fitted. Lighting of hazard

warning lamps on pressing the emergency call button

Absent (2) Single filament halogen bulbs Type of headlamps Discharge bulbs (1) No daytime-running lamps Type of

daytime-running lamps Dedicated

daytime-running lamps

(1)

Presence of a rain and sunlight sensor with wipers with regulated

speed

No Yes

Presence of a lighting stalk with four

positions No Yes (1) Presence of a stalk with one-touch activation of automatic wipe No Yes

Configure yes if the vehicle is fitted with a wipers stalk with « auto » position.

(25)

Key:

Configuration parameter (C) Value to be configured Comments Activation of automatic lighting of headlamps via the personalisation

menu

No (2)

No Presence of a third

button on the high frequency remote control for switching

on the lights Yes

Configure « No » for vehicles fitted with a motorised boot.

No

For all vehicles except those destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)

Lighting of daytime-running lamps by

default

Yes

No

For all vehicles except those destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)

Simultaneous lighting of daytime-running lamps and sidelamps

Yes

Presence of parking

lamps No (2)

Presence of headlamp

height correctors No

(2) Configure this parameter to « No » even if the vehicle is fitted with headlamp height correctors

Presence of the light pack unit

No Yes

Configure yes if the vehicle is fitted with « light bars » under the fascia.

Static lighting controlled by

the BSI

If the vehicle is fitted with halogen bulbs. Type of bend lighting

Dynamic lighting: directional headlamps

If the vehicle is fitted with discharge bulbs. Presence of rear

screen wiping in reverse gear

Absent

(26)

Key:

4.4.4 Menu: locking – doors and tailgate - immobiliser - alarm (menu D)

Configuration parameter (D)

Value to be

Absent If standard tailgate. Opening of the boot

using the high frequency remote

control option Present If motorised boot tailgate.

Deadlocking With a locking control with Deadlocking (to check carry out a Deadlocking actuator test).

Type of locking

Normal locking With a locking control with normal locking (to check carry out a Deadlocking actuator test).

No sun roof 1 sun roof Number /

type of sun roof

blind

(1)

Type of child lock Electric

Mechanical (1)

Absent Left-hand drive vehicle. Passenger door

lock Present Right-hand drive vehicle.

No alarm Without ultra-sonic detectors (on the roof console or on the windscreen aperture pillars)

Standard alarm With ultra-sonic detectors (on the roof console or on the windscreen aperture pillars)

Type of alarm

Alarm for Belgium

For vehicles destined for Belgium with ultra-sonic detectors (on the roof console or on the

windscreen aperture pillars).

Inviolability mode Active (2) (3)

Anti-pinch function on windows and sun roof Present on all openers (2) Presence of a

multiplexed sun roof Absent (2)

Opening of the rear screen using the

high frequency remote control option No (2) Presence of electronically controlled fuel flap

Absent (2) Simultaneous

unlocking of all of the doors

Vehicle with normal unlocking. When actioning

unlocking by high frequency remote

control Unlocking of driver’s

(27)

Key:

Configuration parameter (D)

Value to be

Type of fitting of

alarm Factory fitted alarm (2)

No motorised boot tailgate Type of motorised

boot tailgate Multiplexed motorised boot tailgate (1) Presence of specific high frequency receptor (Japan) Absent (2)

(28)

Key:

4.4.5 Menu: fuel gauge law – oil gauge law (menu E)

Configuration parameter (E)

Value to be

Type of fuel Petrol

Diesel (1)

71 litres For petrol engines. Tank capacity

72 litres For diesel engines. 330 ohms For petrol engines. Gauge resistance for

empty tank _{332 ohms} _{For diesel engines.}

Gauge resistance for full

tank 58 ohms (2)

7 litres For diesel engines. 8 litres For petrol engines. Fuel gauge law - alert

level

9 litres For petrol and alcohol engines. Fuel gauge law -

selection of the vehicle

Petrol vehicles

Diesel vehicles (1)

Oil gauge law – engines

Type of engine: XFV (3.0L petrol) Type of engine: 9HZ (1.6L diesel) Type of engine: RHR (2.0L diesel) Type of engine: 4HP, 4HT (2.2L diesel) Type of engine: UHZ

(2.7L diesel) Type of engine: 6FY

(1.8L petrol) Type of engine: RFJ

(2.0L petrol)

(1)

Engine relay unit (BSM)

For engines:

• 3.0 L petrol (XFV), • 1.6 L diesel (9HZ), • 2.0 L diesel (RHR), • 2.7 L diesel (UHZ). Origin of the oil level

information Engine ECU For engines: • 1.8 L petrol (6FY), • 2.0 L petrol (RFJ), • 2.2 L diesel (4HP, 4HT).

(29)

Key:

4.5 ECUs present

Calculator Value to be

Steering wheel with fixed central

controls Present (2)

Airbag Present (2)

High frequency receptor Absent (2)

Engine relay unit (BSM) Present (2)

Rain / sunlight sensor _PresentAbsent (1)

Driver's door module Present (2)

Built-In Systems Interface Present (2)

Alarm Absent

Present

Depending on presence of ultra-sonic sensors on the roof console or the

windscreen aperture pillar.

Parking assistance _PresentAbsent

Depending on the absence or presence of 4 ultra-sonic sensors in the rear

bumper.

Instrument panel Present (2)

Absent

Without radio type RD4.

With a telematic unit (RT3, RT4 or NG4). With radio navigation (RNEG). Audio equipment

Present With radio type RD4 (CD or CD/MP3).

Lane wandering alert Absent

Present

Depending on presence of a switch for activation of the function.

NaviDrive telematic unit Absent

Present

Depending on presence of a NaviDrive telematic receiver (RT3 or RT4), of a

telematic unit (NG4) or of radio navigation (RNEG).

Absent With telematic unit (RT3, RT4 or NG4) or with radio navigation (RNEG). Display

Present Without telematic unit (RT3, RT4 or NG4) _{or with radio navigation (RNEG).}

Trailer relay unit Absent

Present

Depending on the presence of a trailer relay unit (this equipment is necessary if

the vehicle is fitted with a towbar).

Air conditioning Present (2)

Driver’s seat memorisation control unit

Absent

(30)

Key:

CD changer _PresentAbsent (1)

Hands-Free Kit No

Yes

Configure « Yes » for vehicles with an RD4 radio (or radio navigation (NG4) without service module) and hands-free kit.

To check for the presence of a hands-free kit, press on the « Menu » button of the radio, note the presence of the following icon on the right of the multifunction screen.

Windscreen wipers Present (2)

Audio amplifier _PresentAbsent (1)

Steering angle sensor Present (2)

Engine ECU Present (2)

Automatic gearbox / piloted manual gearbox

Absent

Present (1)

ABS / ESP ECU Present (2)

Absent Vehicle with rubber wheel valves. Tyre under-inflation detection

Present Vehicles with metallic wheel valves.

Variable damping Absent

Present