Night Vision Binoculars VB-007 USER MANUAL

Night Vision Binoculars

VB-007

USER MANUAL

Congratulations on your purchase of this high quality night vision binoculars device. Use this device to view your surroundings in low light conditions or even in complete darkness with the built-in infrared light. You can even take pictures and video using the device which can be stored on a TF card. This device can also be used to take photos and video during the day. Use the supplied A/V cable to view your images on a television or download the images to your computer using the supplied USB cable. Also includes a neck strap and handy storage pouch.

Accessories

1x Night vision binoculars device 1x Mini USB cable

1x Power bank holder 1x A/V cable

1x Storage pouch 1x User manual Over View

Parts overview:

1.Ocular 9.TV out

2.Power button 10. Battery cover

3.IR button 11.Objective lens focus wheel

4.Zoom button 12.Objective lens

5.Mode button 13. Infrared filter

6.Snap button 14.IR Illuminator

7.USB port 15. Infrared zoom

8.TF card slot 16.Tripod adapter

Battery Installation

Open battery compartments and install the 8XAA batteries being sure to follow the polarity markings inside the battery compartment.

Close the battery covers.Please pay attention to the direction of covers.

Inserting / Removing the TF card

Insert the TF card into the TF card port and push until it locks in place.

To remove the installed TF card, please push the TF card inward to release it.

Storage capacity: 8GB or above is recommended

Note: The device will show the icon " "if the micro SD card in not installed.

Turning On the Night vision binoculars device

Power On: Press the power button still for about several seconds to start the Night vision binoculars device.

Turning Off the Night vision binoculars device

Power Off: Press the power button for about several seconds to turn off the Night vision binoculars device.

Key Button Functions

【MODE】 Toggles between Video / Photo / Playback / Menu

【SNAP】

In video mode: Press to take video. To stop recording, press this button again.

In photo capture mode: Press to take photo.

In playback mode: Press to Play or delete the video.

In Menu mode: Press to select.

【ZOOM】

In video mode: Press to zoom out.

In photo capture mode: Press to zoom out.

In playback mode: Press to select the next picture or video In menu mode: Press to select the previous menu listing.

【IR】

In Video/Photo mode: Press to turn on the infrared light. With each additional click, the IR brightness will increase

In playback mode: Press to select the previous photo or video.

In menu mode: Press to select the next menu listing.

Taking Photo and Video Function

Taking a photo: Press the [MODE] button and select the capture photo mode. The icon

will appear in the top left corner of the screen. It means you enter the photo function. Press the [SNAP] button to take photos.

Taking a video: Press the [MODE] button and select the video mode. The icon will appear in the top left corner of the screen. It means you enter the video function. Press the [SNAP] button to start recording video and press the [SNAP] button again to stop recording.

Watching stored videos and photos: Press the [MODE] button and select playback mode . You may then look through your saved photos/videos with the [Zoom] or [IR] buttons.[Zoom] or [IR]

buttons can be used for choosing the previous page or next page.

Deleting Stored Videos and Photos: In playback mode, press the [SNAP] button to enter the menu.

You will be given the options to play or to delete the image or video.While deleting the photo, you will see the menu by pressing the [SNAP] button .The first one is “Delete”.You can choose

“Delete,Delete All or Exit” by [ZOOM] or[IR] . While playing or deleting the videos,you will see the menu by pressing the [SNAP] button.The first one is “Play”.You can choose

“Play,Delete,Delete All or Exit” by [ZOOM] or[IR] button .

The screen display during 【Playback】 mode

Delete Photos

Play/Delete Videos

Focusing the image

Target the object you would like to view and turn the focusing wheel located just below the objective lens until the image on the screen is sharp and clear.The focusing wheel is No.11 in Parts overview picture.

Adjust infrared projection angle

You can adjust infrared projection angle from 5.2°to 10.2° by No.15 in Parts overview picture.

LCD Display Information.

Your screen display in photo mode

1 Icon displaying that you are in Photo Mode

2 Brightness of IR from 1 to 5 (while plugging in USB power supply the IR brightness from 1 to 7)

3 Remain capacity quantity

4 Digital zoom

5 Battery power

6 Backlight from 0 to 15

Your screen display in video mode

1 Icon displaying that you are in Video Mode

2 Brightness of IR from 1 to 5(while plugging in USB power supply the IR brightness from 1 to 7)

3 Remaining time of recording

4 Digital zoom

5 Battery power

6 Backlight from 0 to 15

LCD Display Information.

Press [MODE] four times continuously and enter menu mode.

Note: [ZOOM] means “up” . [IR] means “down” . [SNAP] means “ok” button. After setting, you can press [MODE] again to exit the menu.

Your screen display during menu mode

Format SD

Select to format the TF card

Format is an operation that initializes a partition on a disk or disk. This usually causes all files in the existing disk or partition to be erased.You can choose yes or no by [ZOOM] and [IR] .Lastly press [SNAP] to confirm.

Power Save

Power off mode :The NV can be set to automatically shut down when not operating after the selected period of time.

You can choose off 5min.,15 min.,30 min or cancel. For turning the device off automatically. The buttons of selection and confirmation is the same as mentioned before.Then choose cancel to exit.

Date

ZOOM: UP IR: DOWN SNAP: OK

Find Date input function by [ZOOM] and [IR]. Press [SNAP] to confirm and start to set the date .[ZOOM] means up . [IR] means down . [SNAP] means “ok” button. After setting, you can press [MODE] again to exit.

Time

ZOOM: UP IR:DOWN SNAP:OK

Find time input function by [ZOOM] and [IR]. Press [SNAP] to confirm and start to set the date .[ZOOM] means up . [IR] means down . [SNAP] means “ok” button. After setting, you can press [MODE] again to exit.

Flicker

You can choose 50Hz or 60Hz by [ZOOM] and [IR] .Lastly press [SNAP] to confirm.Then choose cancel to exit.

TV Standard

The video output mode can be set to NTSC (North America) or PAL (Europe)

You can choose NTSC or PAL by [ZOOM] and [IR] .Lastly press [SNAP] to confirm.Then choose cancel to exit.

Language

You can choose language you need by [ZOOM] and [IR] .Lastly press [SNAP] to confirm.

LCD Backlight

set the backlight from 0 to 15

You can choose from level 0-15 to decide screen backlight intensity.Find Backlight function and start to set the level by [ZOOM] or [IR]

button . [SNAP] means “ok” button. After setting, you can press[SNAP]

again to exit.

Date/Time Tag

When you choose on, the date/time will be showed in the picture or video.

You can choose Off or On you need by [ZOOM] and [IR] .Lastly press [SNAP] to confirm.

Version

The software version of the device

Using the zoom function

This device features a zoom function that can be used while taking a video or photo.

Press the [ZOOM] button to toggle between 1X and 3X digital zoom.

Optical magnification power :3.6X-10.8X. (The optical magnification is 3.6X) (3.6X-10.8X Zoom Magnification = Optical Magnification

×

Using IR light in complete darkness

This device can be used in complete darkness when using the built in IR (infrared) light.

Press the [IR] button to activate the infrared light. Remove the IR Lens cover and press the [IR]

button to select between the 5 levels of brightness (while plugging in USB power supply the IR brightness from 1 to 7).

Note:Don’t forget to remove the IR Lens cover while using in the darkness.

Pic. 1

Pic. 2

Viewing videos and photos on TV

Connect the AV output port of the night vision binoculars device with an A/V cable.

Connect the other end of the A/V cable to the TV video input.

In playback mode, press the ZOOM/IR buttons to select the file you will display on your TV.

Note: When the night vision binoculars device is connected to a TV, the screen inside the device will not work.

Transmitting stored videos and photos to a computer

Using a USB cable, you can connect the night vision binoculars device to a computer.

You can find the stored photo/video files on the computer by looking under “My computer \ removable disk”.

Once the removable disk is selected, you can view, delete, move, or copy any video or photo.

Install power bank on night vision binoculars device

Care and maintenance

Clean the device only with a dry or slightly damp, lint-free cloth.

Do not use abrasive cleaners to clean the device.

This device is a high-precision optical instrument, so in order to avoid damage, please avoid the following practice:

●Use the device in ultra-high or ultra-low temperature.

●Keep it or use it in moist environment for long.

●Deliver or use it in strongly shocking environment.

Note:Remove the batteries from the device if it is not used for a longer time.

VB007 Specification

Catalog

Optiacal performance

Magnification (3.6-10.8) X31 Digital Zoom Max 3x

Angle Of View 9.2°

Objective Aperture 31mm Exit Pupil Distance 30mm F# for Objective lens 1.3 IR ZOOM 2X

2m~∞ in daytime; Viewing in the darkness up to 300M (monochrome)

Imager

High-sensitivity CMOS Sensor Size 1/2.7''

Resolution 1920X1080

Displayer

Backlight 0-15 grades adjustment OSD menu display

CVBS always output with VGA resolution

IR LED

TF Card

Operation

Preview

Record JPEG file in TF storage Capture mp4 file in TF storage Playback media file from SD storage

Power

External power supply - DC 5V/2A 8 pcs AA battery 8-12 V

Low battery warning