GREEN BUILDING MATERIAL CERTIFICATION FORM

United States Air Force Academy

Center for Character & Leadership Development

Section: 05 40 00

1.5.D.1 - Green Building Materials

Certification Form

United States Air Force Academy

01 81 13 D - 1

Sustainable Design Requirements

Center for Character and Leadership Development

100% CD Redesign / April 13, 2012

Copyright © Skidmore, Owings & Merrill, LLP 2009

GREEN BUILDING MATERIAL CERTIFICATION FORM

CONTRACTOR: ______________________________________

SPEC SECTION(S): _______________________________

CONTACT

NAME:

TEL. NO.

______ SUBMITTAL NO: _________________________________

Contractor Certification:

I, ________________________________________ a duly authorized representative of__________________________________________________

hereby certify that the information contained herein accurately represents the listed “green building” characteristics of the materials to be provided by our company as components of

the building construction. Furthermore, I understand that any change in such “green building” material characteristics during the purchasing and/or installation period will require prior

written approval from the Owner.

SIGNATURE OF AUTHORIZED REPRESENTATIVE: __________________________________________________

Date:

________

NOTES/ DEFINITIONS:

1.

Post-Consumer Recycled Content: Portion of material or product which derives from discarded consumer waste that has been recovered for use as a raw material (e.g., plastic bottles, newspaper)

2.

Pre-Consumer Recycled Content: Portion of material or product which derives from recovered industrial and mfg. materials that are diverted from municipal solid waste for use in a different mfg.

process, prior to use by a consumer (e.g., fly-ash in concrete or synthetic gypsum board, both of which are by-products of coal-burning power plants). Spills and scraps from the original mfg. process

that are combined with other constituents after a minimal amount of reprocessing for use in further production of the same product do not qualify. Previously called Post-Industrial Content.

3.

Manufactured: Final assembly of components into the building product that is furnished and installed by trades (e.g., if the hardware comes from Dallas, TX, the lumber from Keene, NH, and the joist

is assembled in Kent, WA; then the location of final assembly is Kent, WA).

4.

Harvest Raw Materials: Virgin or recovered resources from which the product’s components are made (i.e., before processing or manufacturing).

5.

Rapidly Renewable: Materials and products made from raw materials that are harvested within a 10-year cycle (e.g., bamboo, cork, linoleum, fast-growing poplar, wheatboard, wool carpet).

6.

FSC Certified: Wood-based products which are certified by the Forest Stewardship Council and carry a Chain-of-Custody certificate number from the vendor or manufacturer.

7.

VOC Content: The quantity of volatile organic compounds contained in products such as adhesives, sealants and architectural coatings. VOC content is to be reported in grams/liter or lbs/gallon.

MR Credit 4.1 - 4.2 Recycled Content, MR Credit 5.1 - 5.2 Regional Materials, MR Credit 6 Rapidly Renewable Materials, MR Credit 7 Certified Wood

Product

Vendor or Manufacturer

(include Location)

Material

COST

(excluding

labor

& equipment)

Contains

Recycled

Content?

Manufactured

w/in 500 miles,

enter

3

(Y/N)

% of Raw

Materials (by

weight)

extracted w/in

500 miles

4

Distance to Job Site

_Contains

Rapidly

Renew-

able

material?

5

(Y/N) & %

For wood

products

% post

con-

sumer

1

% pre

con-sumer

2

Manufact-urer

location in

miles

3

Harvest

Locatio

n in

miles

4

FSC

certified?

6

_(Y/N)

COC

certification

Number for

FSC wood

1.

2.

3.

4.

5.

General Ceiling & Partitions

George Scheidler

_719-574-6450

05 40 00

George Scheidler

_{George Scheidler}

02

Cold-Formed Metal Framing CEMCO, Denver,CO TBD 25.5% 6.8% Y 0% 51m >500 m N N/A N/A

-United States Air Force Academy

01 81 13 D - 2

Sustainable Design Requirements

Center for Character and Leadership Development

100% CD Redesign / April 13, 2012

Copyright © Skidmore, Owings & Merrill, LLP 2009

GREEN BUILDING MATERIAL CERTIFICATION FORM

EQ Credit 4.1: Low Emitting Materials, Adhesives & Sealants

Product Name

Product Type

Manufacturer Name

VOC

7

Content g/L

1.

2.

3.

4.

EQ Credit 4.2: Low Emitting Materials, Paints and Coatings

Product Name

Product Type

Manufacturer Name

VOC

7

Content g/L

1.

2.

3.

4.

EQ Credit 4.3: Low Emitting Materials, Carpet Systems

Product Name

Product Type (Carpet or Cushion)

Manufacturer Name

Green Label

Plus ID

Carpet

VOC

7

mg/m

2

hr

1.

2.

3.

4.

EQ Credit 4.4: Low Emitting Materials, Composite Wood

Product Name

Product Location/Use

Manufacturer Name

Urea-Formaldehyde (Y/N)

1.

N

2.

N

3.

N

United States Air Force Academy

Center for Character & Leadership Development

Section: 05 40 00

1.5.D.2 - GBMCF Back-up Documentation

1.5.D.2.a - Recycled Content

Technical Services Department

263 N. Covina Lane

City of Industry, CA 91744

(800) 416-2278

CALIFORNIA EXPANDED METAL PRODUCTS CO.

November 16, 2011

RE: LEED INFORMATION AND REQUIREMENTS – RECYCLED CONTENT OF COLD-FORMED STEEL

California Expanded Metal Products Company is proud to be a member of the U.S. Green Building

Council and is committed to supplying products that contribute to the improvement of sustainable

design, environmental performance, and economic impact for LEED New Construction and Major

Renovations. CEMCO products and accessories contribute towards LEED credits in the following areas:

LEED Materials & Resources

MR Credit 2.1/2.2 - Construction Waste Management (Up to 2 Points)

Since cold-formed steel is 100% recyclable, CEMCO products can contribute to this credit if the

construction waste on the project is properly diverted from the waste stream. The contribution to this

credit will vary by project and must be determined by the general contractor and/or sustainable design

team.

MR Credit 4.1/4.2 - Recycled Content (2 Points)

The U.S. Green Building Council has determined that a total recycled content of

32.7%

may be utilized

without documentation. A typical breakdown content of our material is:

Post Consumer: 25.5%, Pre-Consumer: 6.8%

Note: While some CEMCO locations have a higher average recycled content, the USGBC default

percentages above are recommended for your project calculations. Project specific recycled content can

be provided upon request.

MR Credit 5.1/5.2 - Regional Materials (2 Points)

CEMCO is committed to the goal of increasing demand for building materials that are sourced,

manufactured and distributed within the specified region; thereby reducing the environmental impacts

resulting from transportation.

While CEMCO has 4 manufacturing facilities serving the Western United States and the steel coil

material that we utilize to cold-form our products is typically sourced within a 500 mile radius of your

project; the majority of “raw” materials used in the production of steel come from various global

sources, and most likely will not be extracted within 500 miles of your project.

Note: Project specific submittal information can be provided upon requires for the above Materials and

Resources categories.

United States Air Force Academy

Center for Character & Leadership Development

Section: 05 40 00

Technical Services Department

263 N. Covina Lane

City of Industry, CA 91744

(800) 416-2278

CALIFORNIA EXPANDED METAL PRODUCTS CO.

CEMCO primary manufacturing facilities:

• City of Industry, California

263 N. Covina Lane, City of Industry, CA 91744

• Pittsburg, California

1001-A Pittsburg Antioch Highway, Pittsburg, CA 94565

• Denver, Colorado

490 Osage Street, Denver, CO 80204

• Forth Worth, Texas

8600 Will Rogers Boulevard, Forth Worth, TX 76140

SS Credit 1: Site Selection (1 Point)

Cold-formed metal framing is a light-weight alternative to conventional concrete construction. In some

cases, the light weight system can reduce foundation requirements, which can minimize the building

footprint.

EQ Credit 3.1: Construction Indoor Air Quality Management (1 Point)

Cold-formed metal framing products are considered inert, so materials will not release terpenes

(hydrocarbons) to the indoor air or provide a food source for mold, bacteria or insects.

Potential Innovations in Design Contributions

(1 Point) CEMCO’s ViperStud framing system provides increased strength capacity from lighter material

that contributes to a lighter building footprint and reduction in energy to produce steel.

(1 Point) An additional point may be earned if the recycled content value of the materials used on the

project reaches the next threshold of 30% total recycled content.

(1 Point) According to the International Residential Code, using metal framing can help reduce or

eliminate the need for chemical based termite control, reducing the impact on the site and air quality.

If you have any questions, concerns or clarifications, please contact our Technical Services department

at (800) 416-2278 or

www.cemcosteel.com

.

Sincerely,

CALIFORNIA EXPANDED METAL PRODUCTS COMPANY

51 miles from jobsite

United States Air Force Academy

Center for Character & Leadership Development

Section: 05 40 00

“S” – PUNCHED “C” STUDS, 54 MIL (16 GA. STRUCTURAL)

Geometric Properties

“S” studs are fabricated in several web depths and flange widths. All CEMCO structural load-bearing studs

are produced from hot-dipped galvanized steel in standard G60 coating. G90 is available upon special request.

Steel Thickness

Color Code (painted on ends)

54 mil: Green

ASTM & Code Standards

■

ASTM A653/A653M, A924/A924M, & A1003/A1003M, C955, C1007

■

SSMA Code Compliance Certification Program

■

AISI S100-2007

■

2006 IBC

■

ICC-ESR 3016

■

2007 CBC

LEED Points and Recycled Content

CEMCO cold-formed steel framing products

contain 30% to 35% recycled steel.

Contact Technical Services at

800.416.2278

for specific information

or email to

[email protected]

Technical Services

( Z )

R.375

(

Y

)

Hole Detail

2 ½” to 3” stud

2.000” 0.750”

3 ½” to 14” stud 3.250” 1.500”

Standard hole

centers are 24”

(Z)

(Y)

1) Uncoated Steel Thickness. Thickness is for carbon sheet steel

2) Minimum Thickness represents 95% of the design thickness and is the minimum acceptable thickness delivered to the job site, based on Section A4.3 of the AISI S100-2007.

Corporate Headquarters

263 N. Covina Lane

City of Industry, CA 91744

Phone:

800.775.2362 |

Fax:

626.330.7598

www.cemcosteel.com

Structural Engineering/Design

1001-A Pittsburg Antioch Hwy

Pittsburg, CA 94565

Phone:

925.473.9340 |

Fax:

925.473.9124

Technical Services

263 N. Covina Lane

City of Industry, CA 91744

Phone:

800.416.2278

|

Fax:

626.249.5005

Manufacturing Facilities

City of Industry, CA

Denver, CO

Ft. Worth, TX

Pittsburg, CA

By using CEMCO metal lath products, your project can contribute

to earning LEED points for:

■

LEED MR 2.1 and 2.2: Construction Waste Management: Up to 2 points.

■

LEED MR 4.1 and 4.2: Recycled Content: Up to 2 points.

■

LEED MR 5.1 & 5.2: Regional Materials

These products are produced from steel consisting of the following contents:

■

Total Recycled Content: 32.9%

■

Post-Consumer Content: 25.6%

■

Pre-Consumer Content: 6.8%

■

CEMCO can provide higher recycled content based on blending steel. Please refer to SSMA

Tech dated May 2009 to calculate recycled content on blended steel.

■

Link to SSMA Tech Note dated May 2009 on LEED® 2.2 Credits for Cold-Formed Steel Framing

Manufacturers: http://www.ssma.com/documents/TN06%20SSMA%20LEED%202.2.pdf

Mil thickness

Design Thickness (in.)

_{Minimum Thickness (in.)}

1 1,2

Yield (KSI)

50

0.0566 (1.44 mm)

0.0538 (1.37 mm)

54

“T” – UN-PUNCHED TRACK, 54 MIL (16 GA. STRUCTURAL)

Geometric Properties

“T” tracks are fabricated in several web depths and flange widths. All CEMCO tracks designed to be used

with structural load-bearing C-Studs are produced from hot-dipped galvanized steel in standard G60 coating

weight. G90 is available upon special request. .

Steel Thickness

Color Code (painted on ends)

54 mil: Green

ASTM & Code Standards

■

ASTM A653/A653M, A924/A924M, & A1003/A1003M, C955, C1007

■

SSMA Code Compliance Certification Program

■

AISI S100-2007

■

ICC-ESR 3016

■

2006 IBC

■

2007 CBC

LEED Points and Recycled Content

By using CEMCO steel framing products, your project can contribute to earning points for:

■

LEED MR 2.1 & 2.2 – Construction Waste Management: up to 2 points.

■

LEED MR 4.1 & 4.2 – Recycled Content: up to 2 points.

■

LEED MR 5.1 & 5.2 - Regional Proximity to project site.

■

For more information on potential LEED points, contact CEMCO at www.cemcosteel.com

CEMCO cold-formed steel framing products

contain 30% to 35% recycled steel.

■

Total Recycled Content: 32.7%

■

Post Consumer: 25.5%

■

Pre-Consumer: 6.8%

Corporate Headquarters & Main Manufacturing Facility

263 North Covina Lane, City of Industry, CA 91744

Phone:

800.775.2362

|

Fax:

626.330.7598

Northern California Manufacturing Facility

1001-A Pittsburg Antioch Hwy, Pittsburg, CA 94565

Phone:

925.473.9340

|

Fax:

925.473.9341

Denver Colorado Manufacturing Facility

490 Osage Street, Denver, CO 80204

Phone:

303.572.3626

|

Fax:

303.572.3627

Mil thickness

Design Thickness (in.)

1

_{Minimum Thickness (in.)}

1,2

Contact Technical Services at

800.416.2278

for specific information

or email to

[email protected]

Technical Services

54

0.0566 (1.44 mm) 0.0538 (1.37 mm)

1) Uncoated Steel Thickness. Thickness is for carbon sheet steel

2) Minimum Thickness represents 95% of the design thickness and is the minimum acceptable thickness delivered to the job site, based on Section A4.3 of the AISI S100-2007.

DESIGN

THICKNESS

0.0566”

Geometric Properties

“U” channels are fabricated in 3/4”, 1-1/2”, 2”, and 2-1/2” widths with 1/2” legs.

All CEMCO U-Shaped channels are produced from hot-dipped galvanized steel in standard

G60 coating weight. G90 is available upon special request.

Steel Thickness

“U” – Un-Punched U-Shaped Channel, 54 Mil (16 ga. structural)

Color Code (painted on ends)

54 mil: Green

ASTM & Code Standards

■

ASTM A653/A653M, A924/A924M, & A1003/A1003M

■

AISI S100-2007

■

2006 IBC

■

2007 CBC

LEED Points and Recycled Content

By using CEMCO steel framing products, your project can contribute to earning points for:

■

LEED MR 2.1 & 2.2 – Construction Waste Management: up to 2 points.

■

LEED MR 4.1 & 4.2 – Recycled Content: up to 2 points.

■

LEED MR 5.1 & 5.2 – Regional Materials.

CEMCO cold-formed steel framing products

contain 30% to 35% recycled steel.

■

Total Recycled Content: 32.7%

■

Post Consumer: 25.5%

■

Pre-Consumer: 6.8%

Contact Technical Services at

800.416.2278

for specific information

or email to

[email protected]

Technical Services

NOTES1. For Deflection calculations, use effective Ixx

Corporate Headquarters & Main Manufacturing Facility

263 North Covina Lane, City of Industry, CA 91744

Phone:

800.775.2362

|

Fax:

626.330.7598

Northern California Manufacturing Facility

1001-A Pittsburg Antioch Hwy, Pittsburg, CA 94565

Phone:

925.473.9340

|

Fax:

925.473.9341

Denver Colorado Manufacturing Facility

490 Osage Street, Denver, CO 80204

Phone:

303.572.3626

|

Fax:

303.572.3627

SECTION PROPERTIES - U CHANNELS

75U050-54 0.0566

0.087 0.30 0.007 0.288 0.002 0.155 0.007 0.019 0.45 315

150U050-54 0.0566 0.129 0.44 0.039 0.547 0.003 0.144 0.039 0.052 1.22 840

200U050-54 0.0566 0.157 0.54 0.079 0.709 0.003 0.136 0.079 0.079 1.87 1190

Section

Area Weight Ix Rx Iy Ry Ix Sx Ma Va

(in

2

_{) (lb/ft) (in}

4

_{) (in³) (in) (in}

4

_{) (in) (in}

4

_{) (in}

3

_{) (in-k)}

Gross Properties

Effective Properties 33 ksi

Design

Thickness

(in)

1) Uncoated Steel Thickness. Thickness is for carbon sheet steel

2) Minimum Thickness represents 95% of the design thickness and is the minimum acceptable thickness

delivered to the job site, based on Section A4.3 of the AISI S100-2007.

Mil thickness

Design Thickness (in.)

1

_{Minimum Thickness (in.)}

1,2

United States Air Force Academy

Center for Character & Leadership Development

Section: 05 40 00

710-WMS Page 1 of 2

MATERIAL SAFETY DATA SHEET

For Welding Consumables and Related Products Conforms to Hazard Communication Standard 29CFR 1910.1200

Date: 2010/01/01 MSDS No. 710

SECTION 1: IDENTIFICATION

Manufacturer Welding Material Sales Inc

1340 Reed Rd Geneva IL 60134 Telephone Number Fax Number 630-232-6421 630-232-4619

Product Identity Flux Cored Electrode

AWS E71T-1, E71T-1/1M,

Trade Name E71T-1

SECTION 2: HAZARDOUS MATERIAL

(1)

IMPORTANT!

This section covers the materials from which this product is manufactured. The fumes and gases produced during welding with the normal use of this product are covered by Section V; see it for industrial hygiene information. CAS Number shown is representative for the ingredients listed. All ingredients listed may not be present in all sizes.

(1) The term “hazardous” in Hazardous Materials” should be interpreted as a term required and defined in the Hazards Communication Standard and does not necessarily imply the existence of any hazard.

Ingredients

CAS No.

Wt. %

TLV mg/m

3

PEL mg/m

3

Titanium dioxides (as Ti)*** 13463-67-7 5 10 10

Manganese and/or manganese alloys and compounds (as Mn)*** 7439-96-5 <5 0.2 1.0(c)

Silicon and/or silicon alloys and compounds (as Si) 7440-21-3 1 10* 10*

Iron 7439-89-6 0.5 10* 10*

Complex compounds 66402-68-4 0.5 **** ****

Fluorides (as F) 7789-75-5 <0.5 2.5 2.5

Borates 1303-96-4 <0.5 1 1

Carbon Steel tube 7439-89-6 85 10* 10*

Supplemental Information: (*) Not listed. Nuisance value maximum is 10 milligrams per cubic meter. PEL value for iron oxide is 10 mg/m3_{. TLV value for iron oxide is 5 milligrams per cubic meter.}

(***) Subject to the reporting requirements of Section 311, 312, and 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of 40CFR 370 and 372. (****) These compounds contain oxides of Si, Ca, Na. The lowest TLV is 2 for those metals and oxides having a TLV listing and 10 milligrams per cubic meter for those not listed. (c) Values are for manganese fume. STEL (Short Term Exposure Limit) is 3.0 milligrams per cubic meter.

SECTION 3: FIRE AND EXPLOSION HAZARD

Non Flammable; Welding arc and sparks can ignite combustibles and flammable products. See Z49.1 referenced in Section 6.

Health: 2 4-Extreme

Flammability: 0 3-High

Reactivity: 0 2-Moderate

Special Hazards: 1-Slight

0-Insignificant *-See Text

SECTION 4: HEALTH HAZARD DATA

Threshold Limit Value: The ACGIH recommended general limit for Welding Fume NOC-(Not Otherwise Classified) is 5 mg/m3

.

ACGIH-1999 preface states that the TLV-TWA should be used as guides in the control of health hazards and should not be used as fine lines between safe and dangerous concentrates. See Section V for specific fume constituents which may modify this TLV. Threshold Limit Values are figures published by the American Conference of Government Industrial Hygienists. Units are milligrams per cubic meter of air.

Effects of Overexposure: Electric are welding may create one or more of the following hazards:

Fumes and Gases can be dangerous to your health. Common entry is by inhalation. Other possible routes are skin contact and ingestion.

Short-term (acute) overexposure to welding fumes may result in discomfort such as metal fume fever, dizziness, nausea, or dryness or irritation of nose, throat, or eyes. May aggravate pre-existing respiratory problems (e.g. asthma,

emphysema).

Long-term (chronic) overexposure to welding fumes can lead to siderosis (iron deposits in lung) and may affect pulmonary function. Manganese overexposure can affect the central nervous system, resulting in impaired speech and

movement. Bronchitis and some lung fibrosis have been reported.

WARNING: This product, when used for welding or cutting, produces fumes or gases which contain chemicals known to the State of Califor nia to cause birth defects and, in some cases, cancer. (California Health & Safety Code

Section 25249.5 et seq).

Arc Rays can injure eyes and burn skin. Skin cancer has been reported.

Electric shock can kill. If welding must be performed in damp locations or with wet clothing, on metal structures or when in cramped positions such as sitting, kneeling or lying, or of there is a high risk of unavoidable or accidental

contact with work piece, use the following equipment: Semiautomatic DC Welder, DC Manual (Stick) Welder, or AC Welder with Reduced Voltage Control.

Emergency and First Aid Procedures: Call for medical aid. Employ first aid techniques recommended by the American Red Cross. If breathing is difficult, give oxygen. If not breathing, employ CPR (Cardiopulmonary

Resuscitation) techniques. In case of electrical shock, turn off power and follow recommended treatment. In all cases call a physician.

SECTION 5: REACTIVITY DATA

Hazardous Decomposition Products: Welding fumes and gases cannot be classified simply. The composition and quantity of both are dependent upon the metal being welded, the process, procedure and electrodes used.

Other conditions which also influence the composition and quantity of the fumes and gases to which workers may be exposed include: coatings on the metal being welded (such as paint, plating, or galvanizing), the number of welders and the volume of the worker area, the quality and amount of ventilation, the position of the welder’s head with respect to the fume plume, as well as the presence of contaminants in the atmosphere (such as chlorinated hydrocarbon vapors from cleaning and degreasing activities.)

When the electrode is consumed, the fume and gas decomposition products generated are different in percent and form from the ingredients listed in Section 2. Decomposition products of normal operation include those originating from the volatilization, reaction, or oxidation of the materials shown in Section 2, plus those from the base metal and coating, etc., as noted above.

Reasonably expected fume constituents of this product would include: Primarily iron oxide; secondarily fluorides and fluorides and complex oxides of silicon, sodium and titanium.

Maximum fume exposure guidelines for this product (based on manganese content) are 1.5 milligrams per cubic meter.

Gaseous reaction products may include carbon monoxide and carbon dioxide. Ozone and nitrogen oxides may be formed by the radiation from the arc.

Determine the composition and quantity of fumes and gases to which workers are exposed by taking an air sample from inside the welder’s helmet if worn or in the worker’s breathing zone. Improve ventilation if exposures are not below limits. See ANSI/AWS F1.1, F1.2, F1.3, F1.4, and F1.5, available from the American Welding Society, 550 N.W. LeJune Road, Miami, FL 33126.

710-WMS Page 2 of 2

Read and understand the manufacturer’s instruction and the precautionary label on the product. Request Lincoln Safety Publication E205. See American National Standard Z49.1 “Safety in Welding and Cutting” and “Allied Processes’ published by the American Welding Society, 550 N.W. LeJune Road, Miami, FL 33126 and SOHA Publications 2206 (29CFR1910), U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954 for more details on many of the following:

Ventilation: Use enough ventilation, local exhaust at the arc, or both to keep the fumes and gases from the worker’s breathing zone and the general area. Train the welder to keep his head out of the fumes. Keep exposure as low as

possible.

Respiratory Protection: Use respirable fume respirator or air supplied respirator when welding in confined space or general work area when local exhaust or ventilation does not keep exposure below TLV. Eye Protection: Wear helmet or use face shield with filer lens shade number 12* or darker. Shield others by providing screens and flash goggles.

Protective Clothing: Wear hand, head, and body protection which help to prevent injury from radiation, sparks and electrical shock. See Z49.1. At a minimum this includes welder’s gloves and a protective face shield, and may include

arm protectors, aprons, hats, shoulder protection, as well as dark substantial clothing. Train the welder not to permit electrically live parts or electrodes to contact skin…or clothing or gloves if they are wet. Insulate from work and ground.

Disposal information: Discard any product, residue, disposable container, or liner as ordinary waste in an environmentally acceptable manner according to Federal, State and Local Regulations unless otherwise noted.

Disclaimer: Although reasonable care has been taken in the preparation of this document, we extend no warranties and make no representations as to the accuracy or completeness of the information contained therein and assume no

responsibility regarding the suitability of this information for the user’s intended purposes as to the suitability of the information for their particular purposes.