Note: This was written for step by step on Windows XP; some screens may appear different if you are using another OS.
Before using your Olimex JTag Programmer
provided by Stanley to the Programmer. This requires you to have the software installed.
Installing the Software:
Step 1: Download the software from the link below
Software: OLIMEX MSP430-PROGRAMMER
stand alone software which allows you to program MSP430 devices Step 2: After clicking on the link to d
Step 3: Open MSPProg_Setup.exe
Note: This was written for step by step on Windows XP; some screens may appear different if you are
Before using your Olimex JTag Programmer for the first time you will need to upload new the Programmer. This requires you to have the software installed.
Download the software from the link below
PROGRAMMER - GUI 1.3.0.4_CLI 2.0.1.2_DLL1.0.4.2/ 17.11.2011 freeware stand alone software which allows you to program MSP430 devices
: After clicking on the link to download the software click open.
Note: This was written for step by step on Windows XP; some screens may appear different if you are
upload new firmware files the Programmer. This requires you to have the software installed.
OLIMEX MSP430
Step 4: “Extract all” files
Step 5: Click Next
Step 6: Click Next
OLIMEX MSP430
Step 8: Open MSPProg_Setup
Step 9: Click Run
Step 10: Click I Agree
Step 11: Note the destination folder you are saving to (defualt should be C: Programmer) --- Click Next
OLIMEX MSP430
Step 12: Click Install
Step 13: Click Yes
Step 14: Click Next
OLIMEX MSP430
Next you have to add the 3 dll and 1 ini files provided by Stanley into the Olimex directory and update the firmware in the Olimex Jtag Programmer
Step 16: Navigate back to the destination you
OLIMEX MSP430-PROGRAMMER SOFTWARE INSTALLATION
have to add the 3 dll and 1 ini files provided by Stanley into the Olimex directory and update the firmware in the Olimex Jtag Programmer
: Navigate back to the destination you picked in step 11 above
INSTALLATION
Step 17: Move the Stanley dll and ini files to
get an error when moving these files if you have the MSP430 Programmer application open. If it is open close it before moving the files to this location
Step 18: Depending on your operating system it may ask you if you would like to keep the old files and rename the new files, you do NOT want t
replace the old files with the new Stanley files. below:
the Stanley dll and ini files to the destination found in the step above ***NOTE: You will these files if you have the MSP430 Programmer application open. If it is open moving the files to this location.***
Depending on your operating system it may ask you if you would like to keep the old files and rename the new files, you do NOT want to keep the old files- picked the option that allows you to replace the old files with the new Stanley files. – You would just click “Yes to All” in the screen shot
found in the step above ***NOTE: You will these files if you have the MSP430 Programmer application open. If it is open
Depending on your operating system it may ask you if you would like to keep the old files and e option that allows you to would just click “Yes to All” in the screen shot
OLIMEX MSP430
Step 19: Download the drivers from the link below (also found on
Drivers:
Windows drivers + MSP430-JTAG-ISO
Step 20: Click Save
Step 21: In the drop down navigate to the destination you
OLIMEX MSP430-PROGRAMMER SOFTWARE INSTALLATION
Step 19: Download the drivers from the link below (also found on www.Olimex.com)
ISO-MK2 firmware version 2.007
In the drop down navigate to the destination you picked in step 11 and click Save
INSTALLATION
Step 22: Click open folder
OLIMEX MSP430
Step 24: Click Next
Step 25: Click Next
Step 26: Uncheck “Show extracted files” and click Finished
Step 27: Navigate to the destination you picked in step : Uncheck “Show extracted files” and click Finished
OLIMEX MSP430
Step 28: Click “Install”
Next you will need to update the firmware in your programmer
Step 29: If your Jtag Programmer is not already plugged in via USB then make that connection now. NOTE: You will also want to have your programmer plugged into daughter card
be plugged into an EL Lockset. If these connections are not made y to Device”
Step 30: “Hardware Wizard” Should pop up once you plug in your device; select yes click next
Step 31: Select “Install the software
Next you will need to update the firmware in your programmer
If your Jtag Programmer is not already plugged in via USB then make that connection now. NOTE: You will also want to have your programmer plugged into daughter card and the daughter should be plugged into an EL Lockset. If these connections are not made you will get an error “Cannont Connect
: “Hardware Wizard” Should pop up once you plug in your device; select yes, this time only
: Select “Install the software from a list or specific location” and then click Next
If your Jtag Programmer is not already plugged in via USB then make that connection now. and the daughter should ou will get an error “Cannont Connect
, this time only and
OLIMEX MSP430
Step 32: Click Browse
Step 33: Browse to the file location of your drivers
OLIMEX MSP430-PROGRAMMER SOFTWARE INSTALLATION
: Browse to the file location of your drivers and click OK once you have the file selected
INSTALLATION
OLIMEX MSP430
***This should load your drivers if it doesn’t you may have missed a step.
Step 35: Looking at your programmer screen make sure the arrow is pointing to “Debugger”
Step 36: Press the right arrow on the JTag Programmer and you will see a screen that looks similar to this:
Step 37: Open Olimex MSP Programmer
OLIMEX MSP430-PROGRAMMER SOFTWARE INSTALLATION
This should load your drivers if it doesn’t you may have missed a step.***
Looking at your programmer screen make sure the arrow is pointing to “Debugger”
arrow on the JTag Programmer and you will see a screen that looks similar to
: Open Olimex MSP Programmer
INSTALLATION
Looking at your programmer screen make sure the arrow is pointing to “Debugger”
OLIMEX MSP430
Step 39: Uncheck all “data memory” boxes and CHECK “SpyBiWire” Box (see green arrows)
Step 40: Click “Blank Check” within the MSP Programmer application (see green arrow)
OLIMEX MSP430-PROGRAMMER SOFTWARE INSTALLATION
: Uncheck all “data memory” boxes and the one “READ” box next to “program memory” also Box (see green arrows). Leave everything else at default.
within the MSP Programmer application (see green arrow)
INSTALLATION
“READ” box next to “program memory” also
Step 41: You will see the following screen if it says NOT blank on both Program and Data memory then the new JTag device has the new firmware uploaded.
Now see “Programming Firmware i
: You will see the following screen if it says NOT blank on both Program and Data memory then the new JTag device has the new firmware uploaded. --- Click OK
Now see “Programming Firmware into your EL Lock”