SET (memory) button and within 5 seconds press the position button

14  Download (0)

Full text

(1)

POWER SlIDING DOORS AND POWER lIFT GATE (if so equipped) POWER SLIDING DOORS

The power sliding doors can be activated by the buttons on the keyfob, the overhead console, and the door pillars.

 To open, close or reverse a sliding door, the ignition switch must be off or the automatic transmission selector lever must be in P (Park).

 To open, close or reverse a sliding door with the keyfob, press and hold the keyfob button for longer than 0.5 seconds.

 To activate a sliding door with the button on the door pillar, the main ON/OFF switch must be on, the door must be unlocked, and the child safety door lock must be in the unlock position.  To activate the power assist feature, manually move a sliding door toward the open or close

position using the inside or outside handle. The power assist feature will automatically complete the motion.

POWER LIFT GATE

The power lift gate can be activated by the buttons on the keyfob, the overhead console, and the rear door pillar.

 To open, close or reverse the lift gate, the automatic transmission lever must be in P (Park).  To open, close or reverse the lift gate with the keyfob, press and hold the keyfob button for

longer than 0.5 seconds.

 To close the lift gate with the rear door pillar button, the main ON/OFF switch must be on. The power sliding doors and the power lift gate have an anti-pinch safety feature. Please refer to your Owner’s Manual for more information regarding this feature.

AUTOMATIc DRIVER POSITIONER (if so equipped) The automatic driver positioner system has two features:  Memory storage function

 Entry/exit function

MEMORY STORAGE FUNCTION

Two positions for the driver’s seat, accelerator and brake pedals, and outside mirrors can be stored in the automatic driver positioner memory. Follow these procedures to set driver preferences.

SET THE DESIRED POSITIONING

1. Set the automatic transmission lever to the P (Park) position.

2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and outside mirrors to the desired positions.

3. Press the SET (memory) button and within 5 seconds press the position button (1 or 2) for at least 1 second until the indicator light illuminates. The position is now stored in memory.

LINK TO KEYFOB

 Within 5 seconds of setting the memory position (indicator light is on and ignition is on), press the

LPD0150

button on the remote.  A keyfob can be linked to each memory button.

 If memory positioning is re-set to a new location, the keyfob automatically re-links.

RECALLING A MEMORY SETTING FROM THE MEMORY PAD

 With the automatic transmission lever in the P (Park) position, press the position button (1 or 2) for at least 1 second.

FROM THE KEYFOB

 If properly linked, operation of the

lpd0151

button will automatically return the driver’s seat, accelerator and brake pedals, and outside mirrors to the memorized position.

ENTRY/EXIT FUNCTION

The driver’s seat moves to allow the driver to get into and out of the driver’s seat more easily. The driver’s seat slides backward when:

 The key is removed from the ignition switch.

 The driver’s door is opened with the key turned to LOCK.

 The key is turned from ACC to LOCK with the driver’s door open and the automatic transmission lever is in the P (Park) position.

The driver’s seat returns to the previous position when:  The key is inserted into the ignition switch.

 The driver’s door is closed with the key turned to LOCK.

 The key is turned from ACC to ON while the automatic transmission lever is in the P (Park) position.

Shift_convention LOCK DOORS

Press the

LPD0150

button to lock all doors. UNLOCK DOORS

Press the

lpd0151

button once to unlock the driver’s door only. Press the button again within 5 seconds to unlock all doors.

POWER SLIDING DOORS (if so equipped) Press and hold the

WPD0336

1A

button for longer than 0.5 seconds to open or close the power sliding door. The door will reverse direction immediately during power open or power close if the keyfob button is pressed. A chime will sound to indicate the reversal.

POWER LIFT GATE (if so equipped) Press and hold the

WPD0337

1A

button for longer than 0.5 seconds to open or close the power lift gate. The hazard lights will flash and a chime will sound to

indicate that the power open or power close sequence has started. If you press the button again, the lift gate will reverse direction immediately; a chime will sound to indicate the reversal.

SIlENcING THE HORN BEEP FEATURE For vehicles without Navigation system:  To deactivate: Press and hold the

LPD0150

and

lpd0151

buttons for at least 2 seconds.  To activate: Press and hold the

LPD0150

and

lpd0151

buttons for at least 2 seconds once more. For vehicles with Navigation system:

 Refer to the “Display screen, heater, air conditioner, audio and phone systems” section in your Owner’s Manual for the procedure.

 If you change the horn beep feature with the keyfob, the display screen will not show the current mode and cannot be used to change the mode. Use the keyfob to return to the previous mode and re-enable the display screen control.

REMOTE KEYlESS ENTRY SYSTEM

200

7

Q

U

E

S

T

Q

U

IC

K

R

E

F

E

R

E

N

C

E

G

U

ID

E

SEEK/TRACK BUTTON

Press the SEEK/TRACK button to skip from one track to another on a CD. Each time the button is pressed, the CD will advance or skip back one track. Press and hold the SEEK/TRACK button for longer than 1.5 seconds to fast forward or rewind a track. The disc will play at an altered speed until the button is released. TUNE/FLDR.CAT BUTTON

Press the TUNE/FLDR.CAT button to manually tune the radio. Press the TUNE/ FLDR.CAT button if playing a CD that is formatted with MP3 folders to skip to the next folder.

FM/AM/SAT* BUTTON

Pressing the FM/AM/SAT* radio select button will change the band to either FM, AM or SAT* radio stations.

SCAN BUTTON

Press the SCAN button to quickly scan through each broadcasting station. The tuner will pause for 5 seconds on each broadcasting station.

PRESET A.B.C BUTTON

Press the PRESET A.B.C button until you reach the desired setting. The radio is equipped with three separate banks, each with six station presets. You may store any combination of AM, FM or SAT* radio presets on each bank.

CD PLAY BUTTON

Press the CD/DVD button to begin CD play. REAR CTRL BUTTON

Press the REAR CTRL button to turn the rear audio controls on. Press again to turn the rear controller off.

SPEAKER CONTROL BUTTON

Press the speaker control button to activate the rear headphones and turn off the rear speakers. Press the button again to deactivate the rear headphones. AUDIO BUTTON

Press the AUDIO button to change the audio settings. Adjust the bass, mid, treble, fade, balance and Speed Sensitive Volume (SSV) by pressing the AUDIO button until the desired mode appears in the display. Press the TUNE/FLDR.CAT button up or down to adjust to the desired level.

STATION AND CD SELECT BUTTONS

To store a station in a preset you must first select A, B, or C memory bank by pressing the PRESET A.B.C button and tune to the desired AM, FM or SAT* station. Then press and hold the desired station select button for at least 2 seconds. When the preset indicator illuminates, a beep will sound, indicating memorization is complete. To retrieve a previously set station, select the memory bank where the preset was set, then press the corresponding station select button.

FM/AM/SAT* RADIO WITH cD cHANGER (if so equipped)

* SAT presets are only available on SAT equipped vehicles.

08

06 07

05

03

02 01

10

04

05 04

09 08 07 06 03 02 01

10

REAR VIEW MONITOR (if so equipped)

When the automatic transmission lever is moved to the R (Reverse) position, the monitor display will automatically change to show the area behind the vehicle.

The colored lines on the display screen indicate approximate distances to objects.

Red 1.5 feet  Yellow 3 feet  Green 7 and 10 feet

STEERING WHEEl SWITcHES FOR AUDIO cONTROl

 To choose Preset A, B, C, CD or SAT (if so equipped) press MODE repeatedly.

 The tuning up or down

<

> switch can be used to

perform the following: • Push the

<

> switch for less than 1.5 seconds to

change to a preset station. • Push and hold the

<

> switch for more than 1.5 seconds to seek to the next or

previous broadcasting radio station. • Push the

<

> switch while playing a CD (if so equipped) for less than 1.5 seconds to

change programs on the CD.

• If the vehicle is equipped with a CD changer, push and hold for more than 1.5 seconds to change between CDs.

HEADlIGHT AND TURN SIGNAl cONTROl HEADLIGHT SWITCH

 Turn the headlight switch to the position to turn on the front parking, tail, license plate and instrument panel lights.

 Turn the headlight switch to the position to turn on the headlights. All other lights remain on.

HIGH BEAM

 Push the headlight switch forward to select the high beam function. The blue indicator light illuminates. Pull the headlight switch back to the original position to select the low beam. The blue indicator light goes off.

 Pull and release the headlight switch to flash the headlight high beams on and off.

TURN SIGNAL SWITCH

 Move the headlight control switch up or down to signal the turning direction. When the turn is completed, the turn signals cancel automatically.

 To signal a lane change, move the headlight control switch up or down to the point where the indicator light begins to flash, but the headlight control switch does not latch.

AUTOMATIC HEADLIGHT OPERATION (if so equipped) The autolight system can:

 Turn the headlights on automatically when it is dark.  Turn the headlights off automatically when it is light.

 Keep the headlights on for 45 seconds after you turn the ignition switch to OFF and all doors are closed.

TO ACTIVATE THE AUTOLIGHT SYSTEM:

 Turn the headlight switch to the AUTO position, then turn the ignition switch to ON.

TO DEACTIVATE THE AUTOLIGHT SYSTEM:

 Turn the headlight switch to the OFF, or position.

FOG LIGHT OPERATION (if so equipped)

Note: The headlights must be on and the low beams selected for the fog lights to operate.

 Turn the switch to the position to turn on the fog lights.  Turn the switch to the OFF position to turn off the fog lights.

WINDSHIElD WIPER/WASHER SWITcH

 The ignition switch must be in the ON position to activate the windshield wipers.

 Push the lever down to operate the windshield wipers.  Switch operation includes:

Intermittent – Wipers operate intermittently and

can be adjusted by turning the time control. Also, the intermittent operation speed varies in accordance with the vehicle speed. (For example, when the vehicle speed is high, the intermittent operation speed is faster.)

Low speed – Wipers operate at a continuous low speed. High speed – Wipers operate at a continuous high speed. Mist – Lift the lever up for one sweep operation of the wiper.

Wash – Pull the lever toward you. Wipers automatically wipe several times.  Rear wiper and washer switch – The rear window wiper and washer operates when the

ignition switch is in the ON position. Switch operation includes: Intermittent (not adjustable) – Wipers operate intermittently. On – Wipers operate at a continuous speed.

Wash – Push the lever away from you. Wipers automatically wipe several times.

INT

lO HI MIST

INT ON

LCN0042

LCN0042

REAR SONAR SYSTEM OFF SWITcH (if so equipped)

When backing up, this system will beep to alert you to obstacles within 6 ft. (1.8 m) of the rear bumper. The system beeps faster as the vehicle gets closer to the obstacle. A continuous tone sounds when an obstacle is less than 10 inches (25 cm) away from the bumper. Turn the system off by pushing the rear sonar system OFF switch. The system will automatically reset the next time the ignition switch is turned on.

lIGHTS ON DEMAND

The LIGHTS ON DEMAND switch allows the driver to select one of three lighting modes for the interior lights and puddle lamps (if so equipped):

Push the top portion of the switch and the interior lights and puddle lamps will illuminate. The lights will turn off automatically after 30 minutes to prevent the battery from becoming discharged. Push the switch to the neutral position and the lights will stay on for approximately 30 seconds when:

 The doors are unlocked by the keyfob, a key, or the power door lock switch while all doors are closed and the ignition switch is in the OFF position.

 The driver’s door is opened and then closed while the key is removed from the ignition switch.

 The key is removed from the ignition switch while all doors are closed.

The interior lights and puddle lamps (if so equipped) will turn off while the 30-second timer is activated when:

 The driver’s door is locked by the keyfob, a key, or the power door lock switch.

 The ignition switch is turned on.

The lights will turn off automatically after 30 minutes while the doors are open to prevent the battery from becoming discharged.

Push the bottom portion of the switch and the interior lights and puddle lamps (if so equipped) will not illuminate.

 The lights can be turned off so sleeping passengers are not disturbed when the doors are opened.

 The lights on the front doors will turn on when the front doors are opened.

09

cONTROl PANEl DISPlAY WITH NAVIGATION SYSTEM (if so equipped) TRIP BUTTON

When the TRIP button is pressed, the fol-lowing modes will display on the screen:  Warning message (if there are any)

 TRIP 1 (Elapsed Time, Driving Distance, Average Speed)

 TRIP 2 (Elapsed Time, Driving Distance, Average Speed)

 FUEL ECONOMY (Average Fuel Economy, Distance to Empty)

 MAINTENANCE (Engine Oil, Tire Rotation and Tire Pressure)

 OFF

MAINTENANCE ITEMS

You can set the engine oil and the tire rotation interval. To display the setting of the maintenance interval, select the ENGINE OIL or TIRE ROTATION key using the joystick and press the ENTER button. To set the maintenance interval, select the MAINTENANCE SCHEDULE key using the joystick and push the joystick to the right or left. To reset the maintenance interval, select the RESET key using the joystick and press the ENTER button. To view the vehicle’s tire pressure, select the TIRE PRESSURE key using the joystick and press the ENTER button.

DISPLAY SCREEN SETTINGS

(2)

QR7E-0V42U0 Printing: Marc h 200 6 (0 8) Niss an, the Niss an Brand Symbol, “S H IFT_” tagline, Z and Niss an model names are Niss an trademarks. ©200 6 Niss an North America, Inc. S h if t _ Th is e as y-t o-u se Q uic k R efe re nc e G uid e i s i nte nd ed to h elp y ou m or e f ully a pp re cia te so m e o f th e u niq ue fe atu re s a nd fu nc tio ns o f y ou r n ew v eh ic le . H ow ev er, it is n ot in te nd ed to re pla ce y ou r O w ne r’s M an ua l. T he O w ne r’s M an ua l c on ta in s m or e d eta ile d i nfo rm ati on to h elp y ou b ett er un de rs ta nd th e i m po rta nt sa fe ty w arn in gs , fe atu re s, op era tio n, an d m ain te na nc e o f y ou r v eh ic le . TI R E P R E S S U R E M O N IT O R IN G S Y S TE M (T P M S ) Th is sy ste m m on ito rs tir e p re ss ure . P le as e r em em be r, t his s ys te m d oe s no t d ete ct a s ud de n d ro p i n t ire p re ss ure (fo r e xa m ple , a b lo w ou t w hile dri vin g). It als o d oe s n ot m on ito r th e a ir p re ss ure in th e s pa re tir e. Tir e p re ss ure is a ffe cte d b y t em pe ra tu re . L ow o uts id e t em pe ra tu re ca us es lo w er tire p re ss ure . T his m ay c au se th e l ow tir e p re ss ure w arn in g l ig ht to illu m in ate . If t he lo w tir e p re ss ure w arn in g l ig ht co m es o n, ch ec k t he tir e p re ss ure in a ll f ou r ti re s. A dju st th e l ow tir e p re ss ure to th e r ec om m en de d C O LD tir e p re ss ure s ho w n o n t he T ire an d L oa din g I nfo rm atio n l ab el to tu rn th e l ow tir e p re ss ure w arn in g l ig ht off . If T P M S is n ot fu nc tio nin g p ro pe rly , th e l ow tir e p re ss ure w arn in g l ig ht w ill f las h f or ap pro xim ate ly 60 s ec on ds w he n t he ke y is tu rn ed o n. A fte r 6 0 s ec on ds , th e l ig ht w ill re m ain o n. H av e t he s ys te m c he ck ed b y a N IS S A N d ea le r. A U TO M A TI c c lI M A TE c O N TR O l ( if so e q u ip p e d ) 02 01 07 08 09 03 06 A U TO B U TT O N  Press the A UT O button 01 . T urn the driver’s side temperature control dial 02 to the desired temperature. T his will allow the fan speed, air flow distribution and temperature to be automatically maint ained.  Press the DU AL 03 button to turn the passenger’s side temperature controls on or off. T his will allow the passenger’s side temperature to be adjusted independently from driver’s side control.  W hen A UT O is pressed, A UT O will be displayed. W hen DU AL is pressed, DU AL will be displayed. D R IV E R ’S S ID E T E M P E R AT U R E C O N TR O L D IA L Turn the driver’s temperature control dial left for cold air or right for hot air . PA S S E N G E R ’S S ID E T E M P E R AT U R E C O N TR O L D IA L Turn the passenger’s temperature control dial left for cold air or right for hot air . A IR F LO W /M O D E B U TT O N S P re ss to s ele ct th e f ollo w in g a ir f lo w o utl ets : Air flows from the center and side vents. Air flows from the center , side, and foot vents. Air flows mainly from the foot vents. Air flows from the defroster and foot vents. Air flows mainly from the defroster vents. FA N S P E E D C O N TR O L B U TT O N S Press (slower) or (faster) button repeatedly to manually control fan speed. Press A UT O to automatically control fan speed. Press O FF to cancel fan speed operation. D E FR OS TIN G /D E FO G G IN G F R O N T A N D S ID E W IN D O W S  Press the defroster control button to turn the system on. T he A/C automatically turns on when the defroster mode is selected.  Turn the driver’s side temperature control dial left or right to set the desired temperature.  To set the defroster on high, press and hold until fan speed increases. D E FR OS TIN G /D E FO G G IN G R E A R W IN D O W A N D (if s o e quip pe d) O U TS ID E H E AT E D M IR R O R P us h t he re ar w in do w d efr os te r s w itc h o n. P us h t he s w itc h a ga in to m an ua lly tu rn th e d efr os te r o ff. Th is fu nc tio n a uto m ati ca lly tu rn s o ff i n a pp ro xim ate ly 15 m in ute s. A /C O N /O FF B U TT O N Press the A/C button to manually turn the A/C on or off. A IR R E C IR C U LA TIO N B U TT O N  Press the air recirculation button to recirculate air inside the vehicle.  Press the air recirculation button again to turn air recirculation off.  The air recirculation mode cannot be selected if the air flow mode is selected. 05 04

09 08 07 06 03 02 01

WINDSHIElD WIPER/ WASHER SWITcH TIRE PRESSURE MONITORING SYSTEM HEADlIGHT AND TURN SIGNAl SWITcH

01

02

03

*See your Owner’s Manual for more information.

lIGHTS ON DEMAND cRUISE cONTROl STEERING WHEEl SWITcHES FOR AUDIO cONTROl 04 05

06 STEERING WHEEl

TIlT ADJUSTMENT* REAR SONAR SYSTEM OFF SWITcH

VEHIclE DYNAMIc cONTROl (VDc) OFF SWITcH*

07

08

09 FRONT-PASSENGER

AIR BAG STATUS lIGHT clIMATE cONTROlS cONTROl PANEl DISPlAY 10 11 12 AUDIO cONTROlS HAZARD WARNING FlASHER SWITcH* 13 14 c R U IS E c O N TR O l  To activate the cruise control, push the ON .OF F switc h. T he indicator light in the instrument panel will illuminate.  To set cruising speed, accelerate the vehicle to the desired speed, push the C O AST/ S ET switc h and release it. T he S ET indicator light in the instrument panel will illuminate.  To reset at a faster cruising speed, push and hold the A C CE L/ R E S switc h. W hen the vehicle reac hes the speed you desire, release the switc h.  To reset at a slower cruising speed, push and hold the C O AST/ S ET switc h. Release the switc h when the vehicle slows to the desired speed.  To resume a preset speed, push and release the A C CE L/ R E S switc h. T he vehicle returns to the last set cruising speed when the vehicle speed is over 24 M P H (3 8 km/h).  To cancel cruise control, push the C ANCE L switc h or tap the brake pedal. T he S ET indicator light in the instrument panel will go out.  To turn off cruise control, push the ON .OF F switc h. B oth the C R U IS E indicator light and the S ET indicator light in the instrument panel will go out. F R O N T-P A S S E N G E R A IR B A G S TA TU S l IG H T This vehicle is equipped with the Niss an Advanced Air B ag system. Under some conditions, depending on pressure detected on the passenger seat and how the seat belt is used, the front-passenger air bag is designed to automatically turn OF F . W hen the front-passenger air bag is OF F , the front-passenger air bag st atus light will illuminate*. F or ex ample:  W hen the system detects that the front-passenger’s seat is occupied by a small adult, c hild or c hild restraint as outlined in the Owner’s Manual, the will illuminate to indicate that the front-passenger air bag is OF F and will not inflate in a crash .  W hen the front-passenger’s seat is occupied and the passenger meets the conditions outlined in the Owner’s Manual, the will not illuminate to indicate that the front-passenger air bag is operational . *W hen the system detects that the fr ont-passenger’s seat is unoccupied, the passenger air bag st atus light will not illuminate even though the fr ont-passenger air bag is OF F. Refer to the Owner’s Manual for det ailed information regarding the Niss an Advanced Air B ag System F R O N T S E A T A D JU S TM E N TS W ith m an ua l s ea ts (if s o e qu ip pe d):  P ull up o n t he le ve r 01 u nd er th e f ro nt of th e s ea t an d s lid e b ac kw ard o r fo rw ard ; re le as e.  Lif t th e l ev er 02 o n t he s id e o f th e s ea t to a dju st yo ur se atb ac k b ac kw ard o r fo rw ard ; re le as e w he n yo u h av e f ou nd a c om fo rta ble a ng le a nd th e s ea t be lt f its p ro pe rly .  U se th e d ials 03 a t th e s id e o f th e d riv er’ s s ea t to ad ju st th e a ng le a nd h eig ht of th e s ea t c us hio n. W ith p ow er se ats (if s o e qu ip pe d):  M ov e t he c on tro l 04 fo rw ard o r b ac kw ard to a dju st th e s ea t c us hio n f orw ard o r b ac kw ard .  P ull up to ra ise th e d riv er’ s s ea t c us hio n; pre ss do w n t o l ow er th e c us hio n. 04  P us h t he s w itc h 05 fo rw ard to m ov e t he s ea tb ac k fo rw ard ; p re ss it ba ck to m ov e t he s ea tb ac k ba ck w ard . Yo ur dri ve r’s s ea t h as a lu m ba r s up po rt; ad ju st it b y m ov in g t he le ve r 06 fo rw ard o r b ac kw ard . 01 02 03 04 05 06 To move the 2nd row seats forwar d or bac kwar d:  Pull the lever 01 up and hold

it while

you slide the seat forward or bac kward to the desired position.  Release the lever to loc k the seat in position. To recline the 2nd row seatbac ks:  Pull the lever 02 up and lean forward or bac k. Th e 2 nd ro w s ea ts c an b e t ip pe d f or w ard fo r e as y e ntr y o r e xit fr om th e 3 rd ro w s ea t:  To enter the 3rd row seats, lift up on the lever 03 located on the lower base of the seat; this tips the seat forward.  To exit the 3rd row seats, pull bac k on the lever on the lower base of the seat and push the seat forward. To fold the 2nd row seats flat to the floor for maximum car go hauling:  Lift up on the recline lever 04 to fold the seatbac k down on the seat base.  Press down on the small lever 05 on the bac k of the seat to release the base of the seat.  Then fold the entire seat forward into the stowed position on the floor 06 .  Reverse this process to return the 2nd row seats to a seating position. Make sure to press the seats down to the floor until they latc h into place. A D JU S TI N G A N D F O lD IN G T H E 2 N D R O W S E A T 01 02 03 06 05 04 To fold the 3r d row benc h seat flat into the floor for maximum car go hauling:  Disconnect and secure the center seat belt and tongue into the retractor base.  Pull the strap 01 on the seatbac k to allow all three head restraints to fold forward.  Pull bac k on the pull strap 02 to release the bac k of the seat and rot ate the seatbac k toward the bac k of the vehicle.  Pull up on the lever 03 located on the bac k of the seat base. T his will fold the seat base toward the bac k of the vehicle.  The entire seat will rot ate toward you and stow flat in the floor . 04  Reverse this process to return the benc h seat to a seating position. Make sure to press the benc h seat down into the floor and pull bac k on the seatbac k until it latc hes into place.  Return all three head restraints to the upright latc hed position. F O lD IN G T H E 3 R D R O W S E A T 01 02 03 04 04 05 02 01 01 04 02 05 03 10 11 12 13 14

06 07 08 09

(3)

QR7E-0V42U0 Printing: March 2006 (08) Nissan, the Nissan Brand Symbol, “SHIFT_” tagline, Z and Nissan model names are Nissan trademarks.

©2006 Nissan North America, Inc.

Shift_

This easy-to-use Quick Reference Guide is intended to help you more fully appreciate some of the unique features and functions of your new vehicle. However, it is not intended to replace your Owner’s Manual. The Owner’s Manual contains more detailed information to help you better understand the important safety warnings, features, operation, and maintenance of your vehicle.

TIRE PRESSURE MONITORING SYSTEM (TPMS)

This system monitors tire pressure. Please remember, this system does not detect a sudden drop in tire pressure (for example, a blowout while driving). It also does not monitor the air pressure in the spare tire. Tire pressure is affected by temperature. Low outside temperature causes lower tire pressure. This may cause the low tire pressure warning light to illuminate.

If the low tire pressure warning light comes on, check the tire pressure in all four tires. Adjust the low tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light off.

If TPMS is not functioning properly, the low tire pressure warning light will flash for approximately 60 seconds when the key is turned on. After 60 seconds, the light will remain on. Have the system checked by a NISSAN dealer.

AUTOMATIc clIMATE cONTROl (if so equipped)

02

01

07

08 06 09 03

AUTO BUTTON

 Press the AUTO button 01. Turn the driver’s side temperature control dial 02

to the desired temperature. This will allow the fan speed, air flow distribution and temperature to be automatically maintained.

 Press the DUAL 03 button to turn the passenger’s side temperature controls on

or off. This will allow the passenger’s side temperature to be adjusted independently from driver’s side control.

 When AUTO is pressed, AUTO will be displayed. When DUAL is pressed, DUAL will be displayed.

DRIVER’S SIDE TEMPERATURE CONTROL DIAL

Turn the driver’s temperature control dial left for cold air or right for hot air. PASSENGER’S SIDE TEMPERATURE CONTROL DIAL

Turn the passenger’s temperature control dial left for cold air or right for hot air. AIR FLOW/MODE BUTTONS

Press to select the following air flow outlets: Air flows from the center and side vents.

Air flows from the center, side, and foot vents. Air flows mainly from the foot vents.

Air flows from the defroster and foot vents. Air flows mainly from the defroster vents.

FAN SPEED CONTROL BUTTONS

Press (slower) or (faster) button repeatedly to manually control fan speed. Press AUTO to automatically control fan speed. Press OFF to cancel fan speed operation.

DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS

Press the defroster control button to turn the system on. The A/C automatically turns on when the defroster mode is selected.

 Turn the driver’s side temperature control dial left or right to set the desired temperature.

To set the defroster on high, press and hold until fan speed increases.

DEFROSTING/DEFOGGING REAR WINDOW AND (if so equipped) OUTSIDE HEATED MIRROR

Push the rear window defroster switch on. Push the switch again to manually turn the defroster off. This function automatically turns off in approximately 15 minutes.

A/C ON/OFF BUTTON

Press the A/C button to manually turn the A/C on or off. AIR RECIRCULATION BUTTON

Press the air recirculation button to recirculate air inside the vehicle. Press the air recirculation button again to turn air recirculation off.

The air recirculation mode cannot be selected if the air flow mode is selected.

05 04

09 08 07 06 03 02 01

WI

N

D

S

H

IE

lD

WI

PE

R

/

W

AS

H

E

R

SWIT

c

H

TI

R

E

PR

E

S

S

U

R

E

M

ON

IT

OR

IN

G

S

Y

STE

M

H

EAD

lI

G

HT

AN

D

TU

R

N

S

IG

NA

l

SWIT

c

H

01 02 03 *See y

ou

r

O

w

ne

r’s

M

an

ua

l f

or

m

or

e

in

fo

rm

at

io

n.

lI

G

HTS

ON

D

E

MAN

D

c

R

U

IS

E

c

ONTR

O

l

STE

E

R

IN

G

WH

E

E

l

SWIT

c

H

E

S

F

OR

A

U

D

IO

c

ONTR

O

l

04 05 06

STE

E

R

IN

G

WH

E

E

l

TI

lT

AD

JU

STM

E

NT*

R

EAR

S

ONAR

S

Y

STE

M

OFF

SWIT

c

H

VE

H

Icl

E

D

YNAM

Ic

c

ONTR

O

l

(VD

c

)

OFF

SWIT

c

H*

07 08 09

FR

ONT

-P

AS

S

E

N

G

E

R

AI

R

B

A

G

ST

A

TU

S

lI

G

HT

cl

IMA

TE

c

ONTR

O

lS

c

ONTR

O

l

P

AN

E

l

D

IS

P

lA

Y

10 11 12

A

U

D

IO

c

ONTR

O

lS

HA

ZAR

D

W

AR

N

IN

G

F

lAS

H

E

R

SWIT

c

H*

13 14

cRUISE cONTROl

 To activate the cruise control, push the ON.OFF switch. The indicator light in the instrument panel will illuminate.

 To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. The SET indicator light in the instrument panel will illuminate.

 To reset at a faster cruising speed, push and hold the ACCEL/RES switch. When the vehicle reaches the speed you desire, release the switch.

 To reset at a slower cruising speed, push and hold the COAST/SET switch. Release the switch when the vehicle slows to the desired speed.

 To resume a preset speed, push and release the ACCEL/RES switch. The vehicle returns to the last set cruising speed when the vehicle speed is over 24 MPH (38 km/h).

 To cancel cruise control, push the CANCEL switch or tap the brake pedal. The SET indicator light in the instrument panel will go out.

 To turn off cruise control, push the ON.OFF switch. Both the CRUISE indicator light and the SET indicator light in the instrument panel will go out.

FRONT-PASSENGER AIR BAG STATUS lIGHT This vehicle is equipped with the Nissan Advanced Air Bag system. Under some conditions, depending on pressure detected on the passenger seat and how the seat belt is used, the front-passenger air bag is designed to automatically turn OFF. When the front-passenger air bag is OFF, the front-passenger air bag status light will illuminate*. For example:

 When the system detects that the front-passenger’s seat is occupied by a small adult, child or child

restraint as outlined in the Owner’s Manual, the will illuminate to indicate that the front-passenger air bag is OFF and will not inflate in a crash.

 When the front-passenger’s seat is occupied and the passenger meets the conditions outlined in the Owner’s Manual, the will not illuminate to indicate that the front-passenger air bag is operational.

*When the system detects that the front-passenger’s seat is unoccupied, the passenger air bag status light will not illuminate even though the front-passenger air bag is OFF.

Refer to the Owner’s Manual for detailed information regarding the Nissan Advanced Air Bag System

FRONT SEAT ADJUSTMENTS With manual seats (if so equipped):

Pull up on the lever 01 under the front of the seat

and slide backward or forward; release.

Lift the lever 02 on the side of the seat to adjust

your seatback backward or forward; release when you have found a comfortable angle and the seat belt fits properly.

Use the dials 03 at the side of the driver’s seat to

adjust the angle and height of the seat cushion. With power seats (if so equipped):

Move the control 04 forward or backward to adjust

the seat cushion forward or backward.  Pull up to raise the driver’s seat cushion; press

down to lower the cushion. 04

Push the switch 05 forward to move the seatback

forward; press it back to move the seatback backward.

Your driver’s seat has a lumbar support; adjust it by moving the lever 06 forward or backward.

01

02 03

04

05

06

To move the 2nd row seats forward or backward:

Pull the lever 01 up and hold it while you slide the seat forward or backward to the

desired position.

 Release the lever to lock the seat in position.

To recline the 2nd row seatbacks:

Pull the lever 02 up and lean forward or back.

The 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:  To enter the 3rd row seats, lift up on the lever 03 located on the lower base of the

seat; this tips the seat forward.

 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and push the seat forward.

To fold the 2nd row seats flat to the floor for maximum cargo hauling: Lift up on the recline lever 04 to fold the seatback down on the seat base.

Press down on the small lever 05 on the back of the seat to release the base of the

seat.

 Then fold the entire seat forward into the stowed position on the floor 06.

 Reverse this process to return the 2nd row seats to a seating position. Make sure to press the seats down to the floor until they latch into place.

ADJUSTING AND FOlDING THE 2ND ROW SEAT

01

02

03

06 05

04

To fold the 3rd row bench seat flat into the floor for maximum cargo hauling:  Disconnect and secure the center seat belt and tongue into the retractor base.

Pull the strap 01 on the seatback to allow all three head restraints to fold forward.

Pull back on the pull strap 02 to release the back of the seat and rotate the seatback

toward the back of the vehicle.

Pull up on the lever 03 located on the back of the seat base. This will fold the seat

base toward the back of the vehicle.

The entire seat will rotate toward you and stow flat in the floor. 04

 Reverse this process to return the bench seat to a seating position. Make sure to press the bench seat down into the floor and pull back on the seatback until it latches into place.

 Return all three head restraints to the upright latched position. FOlDING THE 3RD ROW SEAT

01

02

03

04

04 05

02 01

01

04

02

05

03

10

11

12

13

14

06

07

08

09

cHIlD SAFETY REAR DOOR lOcK

Child safety locks help prevent the sliding doors from being opened accidentally, especially when small children are in the vehicle. The child safety lock levers are located on the edge of the sliding doors. When the lever is in the LOCK position, the door can be opened only from the outside, with the overhead console switch or the keyfob.

ADJUSTABlE AccElERATOR AND BRAKE PEDAlS (if so equipped)

 Adjust the pedals when the automatic transmission lever is in Park.  Push 01 to move the position of the pedals forward.

Push 02 to move the position of the pedals backward.

01

02

FUEl-FIllER DOOR RElEASE

 Press the switch located on the driver’s door to open the fuel-filler door.

 Close the fuel-filler door securely to lock it.

 The driver’s side power sliding door is disabled when the fuel-filler door is open. The sliding door can be partially opened manually.

SUNROOF cONTROlS (if so equipped)

The ignition switch must be in the ON position to operate the sunroof.

TILTING THE SUNROOF

 To tilt the sunroof up, push the tilt switch toward the UP 01 position.

 To tilt the sunroof down, push the tilt switch toward the DOWN 02 position.

SLIDING THE SUNROOF

To fully open the sunroof, push the switch toward the OPEN 03 position.

To fully close the sunroof, push the switch toward the CLOSE 04 position.

 To open or close the sunroof part way, push the switch in either direction (03 or 04) while the sunroof is sliding to stop it in the desired position.

01

02

03

04

SEAT BElT WARNING lIGHT AND cHIME

 The light and chime remind you to fasten your seat belts. The light illuminates whenever the ignition key is turned to the ON or START position and remains illuminated until the driver’s seat belt is fastened. At the same time, the chime sounds for approximately 6 seconds unless the driver’s seat belt is securely fastened.

 The seat belt warning light may also illuminate if the front passenger’s seat belt is not fastened when the front passenger’s seat is occupied. For 5 seconds after the ignition switch is in the ON position, the system does not activate the warning light for the front passenger.

Refer to the Owner’s Manual for detailed information regarding seat belt usage. OUTSIDE MIRROR cONTROl SWITcH

 Rotate the control switch to select the right or left mirror.

 Adjust the mirror to the desired position by moving the control switch.  The selected mirror will automatically tilt down (if so equipped) when

the automatic transmission lever is moved to the R (Reverse) position.

The selected mirror will return to its original position when the automatic transmission lever is moved to any position other than R (Reverse) or if the outside mirror switch is moved to the neutral position.

REAR clIMATE cONTROl DIAlS

To adjust the climate control system for rear seat passengers, use the dials on the overhead console.

REAR FAN SPEED CONTROL DIAL

REAR TEMPERATURE CONTROL DIAL/REAR CTRL BUTTON

Press the REAR CTRL button to transfer rear climate functions to the rear passengers.

(4)

QR7E-0V42U0 Printing: March 2006 (08) Nissan, the Nissan Brand Symbol, “SHIFT_” tagline, Z and Nissan model names are Nissan trademarks.

©2006 Nissan North America, Inc.

Shift_

This easy-to-use Quick Reference Guide is intended to help you more fully appreciate some of the unique features and functions of your new vehicle. However, it is not intended to replace your Owner’s Manual. The Owner’s Manual contains more detailed information to help you better understand the important safety warnings, features, operation, and maintenance of your vehicle.

TIRE PRESSURE MONITORING SYSTEM (TPMS)

This system monitors tire pressure. Please remember, this system does not detect a sudden drop in tire pressure (for example, a blowout while driving). It also does not monitor the air pressure in the spare tire. Tire pressure is affected by temperature. Low outside temperature causes lower tire pressure. This may cause the low tire pressure warning light to illuminate.

If the low tire pressure warning light comes on, check the tire pressure in all four tires. Adjust the low tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light off.

If TPMS is not functioning properly, the low tire pressure warning light will flash for approximately 60 seconds when the key is turned on. After 60 seconds, the light will remain on. Have the system checked by a NISSAN dealer.

AUTOMATIc clIMATE cONTROl (if so equipped)

02

01

07

08 06 09 03

AUTO BUTTON

 Press the AUTO button 01. Turn the driver’s side temperature control dial 02

to the desired temperature. This will allow the fan speed, air flow distribution and temperature to be automatically maintained.

 Press the DUAL 03 button to turn the passenger’s side temperature controls on

or off. This will allow the passenger’s side temperature to be adjusted independently from driver’s side control.

 When AUTO is pressed, AUTO will be displayed. When DUAL is pressed, DUAL will be displayed.

DRIVER’S SIDE TEMPERATURE CONTROL DIAL

Turn the driver’s temperature control dial left for cold air or right for hot air. PASSENGER’S SIDE TEMPERATURE CONTROL DIAL

Turn the passenger’s temperature control dial left for cold air or right for hot air. AIR FLOW/MODE BUTTONS

Press to select the following air flow outlets: Air flows from the center and side vents.

Air flows from the center, side, and foot vents. Air flows mainly from the foot vents.

Air flows from the defroster and foot vents. Air flows mainly from the defroster vents.

FAN SPEED CONTROL BUTTONS

Press (slower) or (faster) button repeatedly to manually control fan speed. Press AUTO to automatically control fan speed. Press OFF to cancel fan speed operation.

DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS

Press the defroster control button to turn the system on. The A/C automatically turns on when the defroster mode is selected.

 Turn the driver’s side temperature control dial left or right to set the desired temperature.

To set the defroster on high, press and hold until fan speed increases.

DEFROSTING/DEFOGGING REAR WINDOW AND (if so equipped) OUTSIDE HEATED MIRROR

Push the rear window defroster switch on. Push the switch again to manually turn the defroster off. This function automatically turns off in approximately 15 minutes.

A/C ON/OFF BUTTON

Press the A/C button to manually turn the A/C on or off. AIR RECIRCULATION BUTTON

Press the air recirculation button to recirculate air inside the vehicle. Press the air recirculation button again to turn air recirculation off.

The air recirculation mode cannot be selected if the air flow mode is selected.

05 04

09 08 07 06 03 02 01

WI

N

D

S

H

IE

lD

WI

PE

R

/

W

AS

H

E

R

SWIT

c

H

TI

R

E

PR

E

S

S

U

R

E

M

ON

IT

OR

IN

G

S

Y

STE

M

H

EAD

lI

G

HT

AN

D

TU

R

N

S

IG

NA

l

SWIT

c

H

01 02 03 *See y

ou

r

O

w

ne

r’s

M

an

ua

l f

or

m

or

e

in

fo

rm

at

io

n.

lI

G

HTS

ON

D

E

MAN

D

c

R

U

IS

E

c

ONTR

O

l

STE

E

R

IN

G

WH

E

E

l

SWIT

c

H

E

S

F

OR

A

U

D

IO

c

ONTR

O

l

04 05 06

STE

E

R

IN

G

WH

E

E

l

TI

lT

AD

JU

STM

E

NT*

R

EAR

S

ONAR

S

Y

STE

M

OFF

SWIT

c

H

VE

H

Icl

E

D

YNAM

Ic

c

ONTR

O

l

(VD

c

)

OFF

SWIT

c

H*

07 08 09

FR

ONT

-P

AS

S

E

N

G

E

R

AI

R

B

A

G

ST

A

TU

S

lI

G

HT

cl

IMA

TE

c

ONTR

O

lS

c

ONTR

O

l

P

AN

E

l

D

IS

P

lA

Y

10 11 12

A

U

D

IO

c

ONTR

O

lS

HA

ZAR

D

W

AR

N

IN

G

F

lAS

H

E

R

SWIT

c

H*

13 14

cRUISE cONTROl

 To activate the cruise control, push the ON.OFF switch. The indicator light in the instrument panel will illuminate.

 To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. The SET indicator light in the instrument panel will illuminate.

 To reset at a faster cruising speed, push and hold the ACCEL/RES switch. When the vehicle reaches the speed you desire, release the switch.

 To reset at a slower cruising speed, push and hold the COAST/SET switch. Release the switch when the vehicle slows to the desired speed.

 To resume a preset speed, push and release the ACCEL/RES switch. The vehicle returns to the last set cruising speed when the vehicle speed is over 24 MPH (38 km/h).

 To cancel cruise control, push the CANCEL switch or tap the brake pedal. The SET indicator light in the instrument panel will go out.

 To turn off cruise control, push the ON.OFF switch. Both the CRUISE indicator light and the SET indicator light in the instrument panel will go out.

FRONT-PASSENGER AIR BAG STATUS lIGHT This vehicle is equipped with the Nissan Advanced Air Bag system. Under some conditions, depending on pressure detected on the passenger seat and how the seat belt is used, the front-passenger air bag is designed to automatically turn OFF. When the front-passenger air bag is OFF, the front-passenger air bag status light will illuminate*. For example:

 When the system detects that the front-passenger’s seat is occupied by a small adult, child or child

restraint as outlined in the Owner’s Manual, the will illuminate to indicate that the front-passenger air bag is OFF and will not inflate in a crash.

 When the front-passenger’s seat is occupied and the passenger meets the conditions outlined in the Owner’s Manual, the will not illuminate to indicate that the front-passenger air bag is operational.

*When the system detects that the front-passenger’s seat is unoccupied, the passenger air bag status light will not illuminate even though the front-passenger air bag is OFF.

Refer to the Owner’s Manual for detailed information regarding the Nissan Advanced Air Bag System

FRONT SEAT ADJUSTMENTS With manual seats (if so equipped):

Pull up on the lever 01 under the front of the seat

and slide backward or forward; release.

Lift the lever 02 on the side of the seat to adjust

your seatback backward or forward; release when you have found a comfortable angle and the seat belt fits properly.

Use the dials 03 at the side of the driver’s seat to

adjust the angle and height of the seat cushion. With power seats (if so equipped):

Move the control 04 forward or backward to adjust

the seat cushion forward or backward.  Pull up to raise the driver’s seat cushion; press

down to lower the cushion. 04

Push the switch 05 forward to move the seatback

forward; press it back to move the seatback backward.

Your driver’s seat has a lumbar support; adjust it by moving the lever 06 forward or backward.

01

02 03

04

05

06

To move the 2nd row seats forward or backward:

Pull the lever 01 up and hold it while you slide the seat forward or backward to the

desired position.

 Release the lever to lock the seat in position.

To recline the 2nd row seatbacks:

Pull the lever 02 up and lean forward or back.

The 2nd row seats can be tipped forward for easy entry or exit from the 3rd row seat:  To enter the 3rd row seats, lift up on the lever 03 located on the lower base of the

seat; this tips the seat forward.

 To exit the 3rd row seats, pull back on the lever on the lower base of the seat and push the seat forward.

To fold the 2nd row seats flat to the floor for maximum cargo hauling: Lift up on the recline lever 04 to fold the seatback down on the seat base.

Press down on the small lever 05 on the back of the seat to release the base of the

seat.

 Then fold the entire seat forward into the stowed position on the floor 06.

 Reverse this process to return the 2nd row seats to a seating position. Make sure to press the seats down to the floor until they latch into place.

ADJUSTING AND FOlDING THE 2ND ROW SEAT

01

02

03

06 05

04

To fold the 3rd row bench seat flat into the floor for maximum cargo hauling:  Disconnect and secure the center seat belt and tongue into the retractor base.

Pull the strap 01 on the seatback to allow all three head restraints to fold forward.

Pull back on the pull strap 02 to release the back of the seat and rotate the seatback

toward the back of the vehicle.

Pull up on the lever 03 located on the back of the seat base. This will fold the seat

base toward the back of the vehicle.

The entire seat will rotate toward you and stow flat in the floor. 04

 Reverse this process to return the bench seat to a seating position. Make sure to press the bench seat down into the floor and pull back on the seatback until it latches into place.

 Return all three head restraints to the upright latched position. FOlDING THE 3RD ROW SEAT

01

02

03

04

04 05

02 01

01

04

02

05

03

10

11

12

13

14

06

07

08

09

cHIlD SAFETY REAR DOOR lOcK

Child safety locks help prevent the sliding doors from being opened accidentally, especially when small children are in the vehicle. The child safety lock levers are located on the edge of the sliding doors. When the lever is in the LOCK position, the door can be opened only from the outside, with the overhead console switch or the keyfob.

ADJUSTABlE AccElERATOR AND BRAKE PEDAlS (if so equipped)

 Adjust the pedals when the automatic transmission lever is in Park.  Push 01 to move the position of the pedals forward.

Push 02 to move the position of the pedals backward.

01

02

FUEl-FIllER DOOR RElEASE

 Press the switch located on the driver’s door to open the fuel-filler door.

 Close the fuel-filler door securely to lock it.

 The driver’s side power sliding door is disabled when the fuel-filler door is open. The sliding door can be partially opened manually.

SUNROOF cONTROlS (if so equipped)

The ignition switch must be in the ON position to operate the sunroof.

TILTING THE SUNROOF

 To tilt the sunroof up, push the tilt switch toward the UP 01 position.

 To tilt the sunroof down, push the tilt switch toward the DOWN 02 position.

SLIDING THE SUNROOF

To fully open the sunroof, push the switch toward the OPEN 03 position.

To fully close the sunroof, push the switch toward the CLOSE 04 position.

 To open or close the sunroof part way, push the switch in either direction (03 or 04) while the sunroof is sliding to stop it in the desired position.

01

02

03

04

SEAT BElT WARNING lIGHT AND cHIME

 The light and chime remind you to fasten your seat belts. The light illuminates whenever the ignition key is turned to the ON or START position and remains illuminated until the driver’s seat belt is fastened. At the same time, the chime sounds for approximately 6 seconds unless the driver’s seat belt is securely fastened.

 The seat belt warning light may also illuminate if the front passenger’s seat belt is not fastened when the front passenger’s seat is occupied. For 5 seconds after the ignition switch is in the ON position, the system does not activate the warning light for the front passenger.

Refer to the Owner’s Manual for detailed information regarding seat belt usage. OUTSIDE MIRROR cONTROl SWITcH

 Rotate the control switch to select the right or left mirror.

 Adjust the mirror to the desired position by moving the control switch.  The selected mirror will automatically tilt down (if so equipped) when

the automatic transmission lever is moved to the R (Reverse) position.

The selected mirror will return to its original position when the automatic transmission lever is moved to any position other than R (Reverse) or if the outside mirror switch is moved to the neutral position.

REAR clIMATE cONTROl DIAlS

To adjust the climate control system for rear seat passengers, use the dials on the overhead console.

REAR FAN SPEED CONTROL DIAL

REAR TEMPERATURE CONTROL DIAL/REAR CTRL BUTTON

Press the REAR CTRL button to transfer rear climate functions to the rear passengers.

Figure

Updating...

References