P
WS-604 V2.06
DIGITAL LED CLOCK
User Guide
West Ocean WS-604 Digital LED Clock User Guide V2 Table of Contents
1. What’s in the box ... 2
2. Get to know your LED Clock ... 3
3. Getting Started ... 4
4. Using the Remote Control Unit ... 6
5. Timer functions ... 9
6. Using a smart phone or PC to control your clock ... 10
Connect your device with your LED Clock ... 10
Set up Wi-Fi ... 11
Optional: Access your clock through Static IP ... 12
Set/synchronize the time automatically via Internet ... 13
Control your Clock remotely via Web Browser ... 13
Set up Daily/Hourly Alarms... 14
Set up and cycle Countdown timer ... 15
Change password to connect your clock ... 15
7. Setting the time with the remote control unit ... 16
8. Updating your Clock ... 17
9. Multiple Mounting options ... 19
10. Customer Support ... 20
11. Specifications ... 20
2 1. What’s in the box
Digital LED Clock User Guide Remote Controller Power Adapter (2m cord) 2 Screws 2 wall plugs
Electrical wire for concealed installation
West Ocean WS-604 Digital LED Clock User Guide V2
2. Get to know your LED Clock The Front:
Yellow light on: Buzzer on Blue light on: Alarm set Yellow light off: Mute Blue light off: No Alarm set Green light on: Wi-Fi connected
Green light off: Wi-Fi connect lost
The Side:
4 The Back:
3. Getting Started
Power up your LED Clock using included power adapter. Default time zone is UTC-8.
The time displayed by the LED clock can be set in three ways: a. Wi-Fi with Internet access
This is the recommended setup for the LED clock. The LED clock have built-in technology to use Wi-Fi to connect to a standard Internet time server. With this feature, it maintains current time automatically without intervention.
Requirement:
• Smart phone with browser • Wi-Fi network information
West Ocean WS-604 Digital LED Clock User Guide V2 Wi-Fi SSID/network name
Wi-Fi Password Time zone
See Set/Synchronize the time automatically via Internetfor the procedure to set/synchronize the LED clock time with the Internet time server.
b. Smart Phone
The LED clock time is set to the same (current) time with a smart phone.
Requirement:
• Smart phone with browser
See Set/Calibrate the time via your smart phone or PC for the procedure to set/synchronize the LED clock time with a smart phone.
c. Remote control unit
The LED clock can be used without Wi-Fi. It is like any normal clock in which the time is specified by hour and minute using the remote control unit.
Requirement:
• Remote control unit
See Using the Remote Control Unit for the procedure to set time manually using the remote controller.
6
4. Using the Remote Control Unit 1. Press M1 to display current Time. 2. Press M2 for 99-0 SECONDS Countdown
• Using numeric keypad until your desired Countdown SECONDS is displayed in SS:MS.
Example: to set up 2 S and 34 MS countdown, press number 0 2 3 4. By incorrect input, press M2 to delete. • Press to start or pause Countdown.
• Upon completion, it will beep one time. 3. Press M3 for 99-0 MINUTES Countdown
• Using numeric keypad until your desired Countdown MINUTES is displayed in MM:SS.
Example: to set up 5 M and 59 S countdown, press number 0 5 5 9. By incorrect input, press M3 to delete. • Press to start or pause Countdown.
• Upon completion, it will beep one time. 4. Press M4 for 99-0 HOURS Countdown
• Using numeric keypad until your desired Countdown HOURS is displayed in HH:MM.
Example: to set up 3 M and 59 S countdown, press number 0 3 5 9. By incorrect input, press M4 to delete. • Press to start or pause Countdown.
• Upon completion, it will beep one time. 5. Mode 5 - Set up 0-99 SECONDS Count up Timer
West Ocean WS-604 Digital LED Clock User Guide V2 • Press until number 5 displayed.
• Press to confirm selected mode. Display format is 00:00 (SS:MS).
• Press to start timer or pause.
• It will beep one time when the timer reaches 99 Seconds and stop.
6. Mode 6 - Set up 0-99 MINUTES Count up Timer • Press until number 6 displayed.
• Press to confirm selected mode. Display format is 00:00 (MM:SS).
• Press to start timer or pause.
• It will beep one time when the timer reaches 99 Min. and 59 Sec and stop.
7. Mode 7 - Set up 0-99 HOURS Count up Timer • Press until number 7 displayed.
• Press to confirm selected mode. 00:00 (HH:MM) will be displayed. Under this mode, the colon ‘:’ will flash at timing and stop at pause.
• Press to start timer or pause.
• It will beep one time when the timer reaches 99 Hours and 59 Minutes and stop.
8
8. Mode 8 - Set up desired number display • Press until number 8 displayed.
• Press to confirm selected mode. The LED screen will be dark. Using numeric keypad to show your desired number or time or score to display. • Press to choose to show colon ‘:’ or not • Press to change.
9. ON/OFF
To turn on or off the screen when you are using it as clock. 10. 12/24
Press this button to switch between 12/12-Hour Time. 11. Mute
Press this button to mute the clock. Please note the clock will only beep if you entered wrong input.
Note: You don’t need Wi-Fi to use Remote Controller.
However, if you want to calibrate the clock, set up alarms or change default setting of Countdowns, you will need to connect your Clock with Wi-Fi.
West Ocean WS-604 Digital LED Clock User Guide V2
5. Timer functions
The LED clock features pre-configured countdown timers. M2-Seconds
Countdown
Count down from
99 seconds:99 milliseconds to 0. Default value is 24 seconds. M3-Minutes
Countdown
Count down from 99 minutes:59 seconds to 0. Default value is 5 minutes.
M4-Hours Countdown
Count down from 99 hours:59 minutes to 0. Default value is 1 hour 30 minutes. Mode 5 Seconds Timer Counting from 0 to 99 seconds:99 milliseconds. Mode 6 Minutes Timer Counting from 0 to 99 minutes:59 seconds. Mode 7 Hours Timer Counting from 0 to 99 hours:59 minutes.
10
6. Using a smart phone or PC to control your clock
Connect your device with your LED Clock
a. Go to the Wi-Fi settings of your smart phone or computer b. Look for and connect to the Wi-Fi network with “WS-XXXX” c. Enter Password “12345678” to connect. (You can change
this password afterwards. Refer to “Change password to connect your clock”)
d. Once your device is connected to your LED Clock, open your web browser and type
“192.168.4.1” in the URL address bar. Press Enter or Go. Note: This network provides access to the LED Clock setup page only. If you see an “Unsecured Network” or “No Internet Connection” message, please ignore it and connect anyway. e. The LED clock system appears.
West Ocean WS-604 Digital LED Clock User Guide V2 Set up Wi-Fi
a. Select “Wi-Fi Settings” on main menu.
b. On the “Wi-Fi Settings” screen, enter name of your Wi-Fi network and password. c. Check “Adjust for US daylight
savings time automatically”. d. Select correct Time zone. e. Tap on “Save”.
f. Unplug clock, wait for 3-5 seconds, and plug it back in.
g. Upon success connection, green light on the screen will turn on automatically. The LED clock time will
automatically update/adjust to the correct current time. h. Reload the browser. The browser will display the LED
clock’s IP address (Local IP) assigned by your network automatically.
As the LED clock is now connected to the user’s Wi-Fi network, go to the Wi-Fi settings of your device and select the normal Wi-Fi network.
Open your web browser and in the URL address bar enter the assigned Local IP address to launch the Control Menu.
12
Moving forward, access to the LED clock (i.e. for remote control or changing the settings) will be through the Local IP address.
Optional: Access your clock through Static IP
If the clock is on a network with a lot of devices, it can be annoying to look up the Local IP address assigned through steps above when you need to access your clock remotely. Because if the clock hasn't connected in a few days, its IP address can be assigned to something else.
Utilizing a static IP address on your clock avoids any IP address conflicts and provides more accurate geolocation than a dynamic IP address. To configure static IP for your clock manually, you will need to know:
• Available IP address on your network • Gateway IP
• Subnet Mask
You can find all this information on your computer and/or router depending on the device and network you are using. Once you obtain all this information,
• go to “Wi-Fi Settings” on main menu, enter all information on the loaded page
• Check “Static IP”
West Ocean WS-604 Digital LED Clock User Guide V2 Moving forward, access to the LED clock (i.e. for remote control or changing the settings) will be through the Static IP address.
Set/synchronize the time automatically via Internet
a. Select “Clock Calibration” on main menu.
b. On the next screen, select “Sync Time”.
c. Upon completion, the message “Successfully Calibrated” will appear to indicate the LED clock time is now the same as your device. Control your Clock remotely via Web Browser
a. Select “Remote Control” on main menu.
b. Manage your LED clock like using a Remote Control unit on the loaded screen.
c. Note: If the screen stopped to respond, just refresh the page.
14
Set up Daily/Hourly Alarms
a. Select “Alarm Settings” on main menu.
b. On the next screen, tap the desired
- Daily Alarm or Hourly Alarm - to set/configure.
c. When setting up Daily Alarm: - Specify the time
- Specify the day(s) of the week
d. When setting up Hourly Alarm, specify the minute when the LED clock will sound. For example, specify 0 so that the LED clock will sound as each hour starts.
e. Tap “Save” when done.
Once the alarm has been set up successfully, blue light on the LED clock screen will turn on to indicate alarm(s) have been configured/set.
West Ocean WS-604 Digital LED Clock User Guide V2 Set up and cycle Countdown timer
Manage settings for button M2, M3, M4 on the remote a. Select “Countdown Timer
Settings” on main menu. b. On the loaded screen, tap to
manage your desired timer settings upon your personal preference and tap Save. c. Select the countdown timer you
would like to cycle automatically. d. Tap “Save”.
Change password to connect your clock a. Select “New Password for
Access Point” on main menu. b. On the loaded screen, enter old
password “12345678” c. Enter new password d. Tap “Save” and restart your
clock.
Note: Set up a new password will require you to reset your Wi-Fi Settings. After restarting your
16
7. Setting the time with the remote control unit • Unplug your Clock
• Press and hold the “MODE” button on the back of the clock, while plug in power adapter
• Release the “MODE” button
• The clock displays “1” indicating “Time Setup Mode”. • Follow instructions below, we take 17:41, Sunday,
November 04, 2018 as example:
By incorrect entering, it will beep and won’t go to next step. Note: To set up Day of The WEEK
01 for Monday 02 for Tuesday
03 for Wednesday 04 for Thursday 5 for Friday 06 for Saturday 00 for Sunday
West Ocean WS-604 Digital LED Clock User Guide V2
8. Updating your Clock
If you would like to know software updates, please email our support team at [email protected]
a. Download update file (ws604_v2.0X_XX) from support team. Please check name and size of the downloaded file to make sure it is the correct version.
b. Connect your Clock with your device as below.
Note: If you are using static IP, just type your static IP/update in the URL address bar and enter.
Skip to point “e”.
c. Go to the Wi-Fi settings of your smart phone or computer and connect to the Wi-Fi network name started with “WS-XXXX”
18
e. Open your web browser and in the URL address bar enter 192.168.4.1/update and press Enter or Go. User name: admin
Password: admin Note: Case Sensitive
f. On the loaded page, upload the file (ws604_ v2.0X_XX) you received from our support team.
BE CAREFUL when you are updating
the file: MAKE SURE you have selected the correct file. Uploading WRONG file will lead the clock to malfunction and this is irrevocable!
g. Upon successful updating, your LED Clock will beep and restart itself.
Important: Follow these steps to apply new software:
1. Unplug the clock. (wait for 5-10 seconds)
2. Press / hold the “ON/OFF” button on the back of the clock. 3. Plug in power adapter.
4. Release the “ON/OFF” button after the beep.. Congratulations!
West Ocean WS-604 Digital LED Clock User Guide V2 9. Multiple Mounting options
We offer you with multiple mounting options.
Place it on tripod through
integrated tripod mounting hole.
2 Screws and 2 plastic expansion anchors for mounting in-wall.
Electrical wire for concealed installation in-wall.
Note: With built-in G sensor, the clock has auto-rotate function. You can place it or install it in any direction you want despite of position of the power cord.
20 10. Customer Support
Should you have any questions, please contact our friendly support team at [email protected].
11. Specifications
• Dimensions: 18”×6.85”×0.95” • Size of single digital(H x W): 6.1”×3.4” • Weight:1.91 lbs.
• Wi-Fi: 802.11 b/g/n
• Battery: 1 LIR1220 (included)
• Power Supply: Power adapter, DC 9-28V / 6.4 Watt (Max) • Working environment:
Operating Temp: 0 to 40 C〫/ 32 to 104 F Storage Temp: 0 to 60 C〫/ 32 to 140 F Operating Humidity: 10% to 90% RH 12. Using Tips
• Before starting the clock configuration for Set/synchronize the time automatically via Internet, prepare the Wi-Fi network name and password.
• The setup process must be completed on the Wi-Fi network in which it will be used.
• If using the clock without an Internet connection, it is recommended to recalibrate the clock from time to time using a smart phone.
West Ocean WS-604 Digital LED Clock User Guide V2 • The clock has an internal battery as a backup power source to preserve settings in case of a power outage. Use the provided power adapter as the power source of the clock. • Reset/clear the clock network setting before transferring the clock to a different location which have a different Wi-Fi network. Wi-Fi has been set if the green LED is on. Follow these steps to clear the Wi-Fi settings:
5. Unplug the clock. (wait for 5-10 seconds)
6. Press and hold the “ON/OFF” button on the back of the clock.
7. Plug in power adapter.
8. Release the “ON/OFF” button after the beep.
The Wi-Fi settings have been cleared if the green LED has turned off. Note that the alarm and timer settings are simultaneously cleared during the procedure. Repeat the steps if the green LED have not turned off.
• If it is difficult to connect a smart phone with the clock, try to clear the Wi-Fi settings (the steps above) and try again. • If the Green light is flashing, it means that you might not provide correct Wi-Fi information. Please double check if you have correct Wi-Fi name and password (case sensitive).
22
• If the green light on the clock screen went off, it means that the clock lost Wi-Fi connection. The clock cannot be controlled or managed via smart phone until Wi-Fi is available. The clock will still work using the remote controller. If Wi-Fi is available, repeat Set/synchronize the time automatically via Internet to reconnect the LED clock to the Internet.
• Q: Do I need to connect my clock with Internet? A: the answer is YES, if you wish to
- surfer online while viewing and controlling your LED Clock.
