The College of Electrical Training (CET) is the major private
training provider for the Western Australian
electrical & telecommunications industries.
Our administration team will be happy to assist you.
Our administration team will be happy to assist you.
Please call us for enquiries & course bookings.
Please call us for enquiries & course bookings.
Joondalup Campus
20 Injune Way, Joondalup WA 6027 PO Box4, Joondalup DC WA 6919 Ph (08) 9301 1560 Fax (08) 9301 5059
Jandakot Campus
5 Avior Avenue, Jandakot WA 6164 PO Box 3857, Success WA 6964 Ph (08) 9417 8166 Fax: (08) 9417 8766
Check out our website
www.cet.asn.au
RTO No 2394
Pre-Apprenticeship Training
Apprentice Training
Post-Trade Training
Short Refresher Courses
Course Delivery Profile
Course Delivery Profile
Training Delivery
The CET’s flexible approach to training delivery means that in addition to training being delivered at the College’s modern ‘state of the art’ facilities, some courses may be completed by
correspond-Customised Training
We are able to customise courses to suit your training needs. Call our friendly administration team for further information.
THE CET
ELECTRICAL APPRENTICESHIP TRAINING
Assessment & Testing
Pre Selection Testing
We provide aptitude testing for persons wishing to enter an apprenticeship in the electrical trade.
Duration: 1.5 hours
Delivery: Subject to demand
Cost: $66.00—Private bookings only
Electrical Trade
Certificate II in Electrotechnology (Career Start) (Pre Apprenticehsip Electrical UEE 22011) Duration: 632 hrs (includes 200 hrs work experience)
Delivery: Full Time
Cost: Government fees (POA)
In addition to essential knowledge and practical skill development the qualification offers applicants with the opportunity of work experience in the electrical trade. Competency plus a selection of Elective Units of Competency relevant to the Electrical Apprenticeship.
Certificate III in Electrotechnology Electrician (Electrical Apprenticeship UEE 30811)
Duration: Generally, the off-the-job component is completed over three years.
Delivery: Day or Block release
Cost: Government fees (POA)
All units of competency must be successfully completed and the apprentice deemed competent in order to attain a certificate. A WA Unrestricted Electricians Licence is granted upon application and successful completion of the apprenticeship. The essential 66 capabilities identified by ERAC and endorsed by Energy Safety are covered in the qualification.
Certificate III in Electrical Fitting (Electrical Apprenticeship UEE 33011)
Duration: Generally, the off-the-job component is completed over three years.
Delivery: Day or Block release
Cost: Government fees (POA)
This qualification provides competencies to manufacture, fit, assemble, erect, operate, test, fault find, alter and repair electrical equipment; and includes electrical wiring work where that work is associated with assembling, maintaining, terminating or altering the wiring between electrical com-ponents within plant or machinery.
These training programs have been funded by the Department of Training and Workforce Development
ELECTRICAL LICENCE COURSES
POST-TRADE
ELECTRICAL CONTRACTORS LICENCE
Electrical Contractors Licence
Comprising of modules
EA103A, EA103B, EA102 & WAE100
Duration: 102 hours
Delivery: Full time or
Distance Learning
Course Fee: $2,042.00
NECA members: $1,882.00
Fees include $65.00 of Resource Fees for WAE100, EA102 & EA103B
Electrical Contractors Nominees Licence
Comprising of modules
EA103A & WAE100
Duration: 39 hours
Delivery: Full time or
Distance Learning
Course Fee: $986.00
NECA members: $886.00
Fees include $20.00 Resource Fee for WAE100
EA103A Operational
(Electrical) Legislation
Offers the skills necessary for the application of the State Electrical, Safety and Mines Legislation requirements in the completion of an Electrical Installation
Duration: 11 hours
Delivery: Full time or
Distance Learning
Course Fee: $183.00
NECA Members: $174.00
Estimating, Tendering & Contracting
EA104
A practical guide to greater control over the company’s financial planning, management and flow.
Duration: 39 hours
Delivery: Full time or
Distance Learning
Course Fee: $936.00
NECA members: $836.00
WAE100 Electrical Requirements
Mandatory licensing module designed to up-skill electrical based skills in the areas of standard legislation and testingDuration: 32 hours
Delivery: Full Time or
Distance Learning
Course Fee: $803.00
NECA members: $765.00
Fees include $20.00 Resource Fee
EA102 Establishing a
Contracting Business
This program provides the building foundation skills to establish a contracting business
Duration: 39 hours
Delivery: Full Time or
Distance Learning
Course Fee: $1035.00
NECA members: $986.00
Fees include $25.00 Resource Fee
EA103B General Legislative Requirements
Provides the knowledge of State and Federal Legislation relevant to WA business operationsDuration: 20 hours
Delivery: Full time or
Distance Learning
Course Fee: $577.00
NECA members: $557.00
Certificate IV in
Electrical-Instrumentation
UEE40411
Certificate IV in Electrical - Instrumentation
This course is designed to provide the Electrical Tradesperson and final year Electrical Apprentice with training in the functionality, operation, calibration and fault finding of basic Industrial Instrumentation. The course provides underpinning knowledge of Instrumen-tation theory, calibration and processes through a web-based training program which is self-paced and sup-ported administratively and technically by the College. The knowledge obtained through the online tuition is then applied in simulated workplace training units within the College in areas such as pressure, level, tempera-ture, flow, transducers and application to analytical in-struments. This can be undertaken once the web-Based programs are completed. Competency can be achieved through repeated undertaking of practical pro-jects at the College or through workplace activities. Stu-dents should ideally have home broadband internet access.
Duration: This is a self-paced course with a large
per-centage of the theory being delivered online at the stu-dents’ pace (it should be noted that online training must be fully completed within 12 months). Once the online component is completed the student can undertake the practical sessions and undergo assessment. Classes in the practical component will typically be run each month.
Non-Subsidised Fee: $5000.00
Subsidised Fee: Not Available
ELECTRICAL LICENCE COURSES
POST-TRADE
Restricted Electrical License
(REL)
REL Restricted Electrical Licence For persons who regularly need to perform electrical work associated with a primary work function or ac-tivity.
Modules to be completed as directed by Energy Safety and will be dependent upon the work area category for which the licence is required.
MODULE 1 Electrical Principles and Safety
Duration: 16 hours
Delivery: Full-time
Course Fee: $500.00
Subsidised Fee: $260.00
MODULE 2 Disconnect & Reconnect to 1000V
Duration: 24 hours
Delivery: Full-time
Course Fee: $480.00
Subsidised Fee: $144.00
Western Power
Contractor Connect Training
Scheme
Western Power Contractor Connect Training Scheme
This course is designed for Western Power accredit-ed Electrical Contractors and authorizaccredit-ed Electrical workers undertaking ‘Energising the Installation’ tasks.
Duration: 8 hours
Delivery: Full time
Non-Subsidised Fee: $280.00
Subsidised Fee: $ 84.00
Western Power
Service Apparatus Connection
Western Power Service Apparatus Connection
This course is designed for Western Power accredit-ed Electrical Contractors and authorizaccredit-ed Electrical workers to be approved to connect consumers to the Network.
Duration: 8 hours
Delivery: Full time
Non-Subsidised Fee: $310.00
Subsidised Fee: $ 93.00
Course in
Electrical Trade Licensing
This course has primarily been developed to ensure that persons holding an Australian Trade Certificate in the trades of Electrical Mechanics or Electrical Fitting are provided with the skills and knowledge to be issued with a Western Australian Electrician’s License.
Duration: 80 hours over a 2 week period
Delivery: Full time
Course Fee: $1012.00
Minimum Australian Context Gap
Training
This course provides Minimum Australian Context Gap training for the UEE30807 Certificate III in Elec-trotechnology Electrician qualification.
Duration: 170 hours split over Part A and
Part B
Delivery: Full time
Course Fee:
Part A $1640.00
Programmable Logic Controllers
Skill Set
SHORT COURSES
POST-TRADE
High Voltage Switching
Systems Operations Course
High Voltage Switching Systems
Provides the knowledge needed for entry to HVS industry. Designed for persons requiring an understanding of HVS or who operate high voltage equipment. Industry recognised training using Brown Boveri equipment.
Duration: 5 days
Delivery: Full-time
Subsidised Fee: $1350.00
Non-Subsidised Fee: $2550.00
Low Voltage Switchboard Rescue
The course provides an introduction to basic electrical safety and life support. It examines the principles of working safely in confined spaces, hazard identification, effects of electric shock, first aid and resuscitation for persons suffering from electrocution and rescue techniques using a Low Voltage Switchboard Rescue Kit.
Duration: 8 hours
Delivery: Full-time
(subject to demand) Subsidised Fee: $188.00
Non-Subsidised Fee: $300.00
Low Voltage Switchboard Rescue
Certificate IV in Hazardous Areas
–Electrical UEE42611
Certificate IV in Hazardous Areas-Electrical
The course provides; competencies to supervise, select, install, commission, maintain and test explosion-protected equipment and systems; for control and monitoring of plant and processes. It also contains Skill Sets in working with explosion protection techniques and how they apply to pres-surisation; and gas and dust atmospheres.
Duration: 80 hours
Delivery: 2 weeks full-time with the
option of splitting the 2 weeks within a period of 3 months
Non-Subsidised Fee: $3300.00 Subsidised Fee: Not Available
Course in Programmable Logic Controllers Skills Set - UEENEEI150A & UEENEEI151A UEENEEI150A covers development, installation
and testing of programs for Programmable Logic Controllers (PLC's) for systems requiring extend-ed control functions.
Duration/Delivery: 2 evening per week for 5 weeks
UEENEEI151A covers development and testing
of programs for industrial systems requiring ad-vance control functions using structured logic design techniques and the application of high level instructions.
Duration/Delivery: 2 evening per week for 6 weeks
NECA Subsidised Fee: $ 250.00
Subsidised Fee: $ 300.00
Loop Impedance Testing
This course provides information and training in current loop impedance testing procedures and a skills update in the use of testing equipment
Duration: 4 hours
Delivery: Full-time or after hours (subject to demand)
Subsidised Fee: $55.00
Non-Subsidised Fee: $96.00
Loop Impedance Testing
SHORT COURSES
Certificate IV in
Electrical-Photovoltaic Systems
UEE42010 Certificate IV in Electrical-Photovoltaic SystemsThis nationally recognised qualification provides Electricians with the competencies to install, set up, test, fault find and repair Photo-voltaic Systems in domestic and commercial premises. It contains Units of Competency endorsed by the Clean Ener-gy Council and information regarding the use and application of Interval Metering.
Duration: 5 days plus 1 evening
Delivery: Full-time
Non-Subsidised Fee: $3,000.00
Work Safely in the Construction Industry CPCCOHSI001A
This course is designed to raise safety awareness amongst employers and employees engaged in building and construction work in Australia.
Duration: 4 hours
Delivery: On demand
Non-Subsidised Fee: $99.00
NECA Member Fee: $60.00
Work Safely in the
Certificate II in Split Air
Conditioning and Heat Pump
Systems
Certificate II in Split Air Conditioning and Heat Pump Systems
This course covers the installation, commissioning and de-commissioning of single head, split air con-ditioning and heat pumps systems to a prescribed routine where the maximum plant capacity for each system does not exceed 18 kWr including wall hung, floor and ceiling suspended, cassette and ducted fan coil split systems and water heating heat pump systems.
Duration:
Face to face 10 days
Delivery: Full-time
Non-Subsidised Fee: $2500.00
Subsidised Fee: $1300.00
UEESS00101 Sustainable -
Designer,
Installer of Grid Connected
UEESS00101 Sustainable - Designer, Installer of Grid Connected Photovoltaic Systems Skill Set
This Skill Set provides licensed electricians with the training to design, install, set up, test, fault find, re-pair and maintain grid connected photovoltaic sys-tems and associated equipment.
Duration: 5 days & 1 evening1
Delivery: Full-time
Non-Subsidised Fee: $1,200.00
EcoSmart Electricians Course
EcoSmart Electricians Course
This is a new innovative training program devel-oped by NECA which will comprise training for electricians and electrical engineers that will equip them to deal with the rapidly growing de-mand by consumers for improved energy effi-ciency.
Duration: 3 days
Delivery: Full-time
on-site training availa-ble
Fee: $490.00
Subsidised Fee: $147.00
NECA Members $ 47.00
Prevention of Electrical Incidents
Ideally, this course attempts to eliminate electrical inci-dents through providing knowledge, raising awareness and introducing safe work practices into the electrical workers daily routine. It also provides a genuine means by which an employer of electrical workers can be assured they are meeting their ‘Duty of Care’ re-sponsibilities. Duration: 8 hours Delivery: Full-time (subject to demand) Non-Subsidised Fee: $176.00 Subsidised Fee: $ 53.00
Prevention of
Electrical Incidents
SHORT COURSES
Prevention of
Electrical Incidents 2
Prevention of Electrical Incidents 2
This course is the second in a series and aims to re-fresh students on the previous course outcomes and introduce additional areas where potential electrical incidents could occur and training is required. It rein-forces the need for the electrical worker to be extra careful when working in certain electrical situations. The training of this course addresses the need to elim-inate electrical incidents by providing knowledge, rais-ing awareness and reinforcrais-ing the need for safe work-ing practices in the industry.
Duration: 8 hours
Delivery: Full-time
(subject to demand)
Non-Subsidised Fee: $176.00
Subsidised Fee: $ 53.00
Basic Workplace First Aid Training
HLTFA211A Provide Basic Emergency Life SupportBasic Workplace First Aid Training The aim of this course is to develop skills and knowledge required to recognise and respond to life threatening emergencies. This includes calling for help, providing basic life support and basic manage-ment of common life-threatening conditions in a workplace context.
Duration: 8 hours
Delivery: Full-time: 1 day
Non-Subsidised Fee: $150.00
Subsidised Fee: $45.00
COURSE AVAILABLE ON DEMAND ONLY
Senior First Aid Training
HLTFA301B Apply First Aid
Senior First Aid Training
The aim of this course is to develop skills and knowledge required to provide a first aid response including life support and management of more complex casualties until the arrival of medical or other assistance. These skills may be applied in a range of situations, including community and work-place settings.
Duration: 16 hours
Delivery: Full-time: 2 days
Non-Subsidised Fee: $186.00
Subsidised Fee: $56.00
COURSE AVAILABLE ON DEMAND ONLY
Basic Resuscitation Training
The aim of this course is to develop skills and knowledge required to deliver basic resuscitation, including calling for help and providing basic life sup-port. (Minimum certificate requirement for entry onto any Western Power site).
Duration: 4 hours
Delivery: Full-time: 1/2 day
Non-Subsidised Fee: $110.00
Subsidised Fee: $33.00
Basic Resuscitation Training
Electrical Cords & Plugs
Electrical Cords & Plugs Non-Licenced The Cords & Plugs course provides persons with the training, skills and knowledge required to fit low volt-age plug tops and assemble extension leads (up to 1000 volts AC). The course is structured to include both theoretical and practical training. The College’s training facilities allow for skills to be practiced in a simulated workplace environment. This course is de-signed for those persons who need to perform electri-cal work that is associated with low voltage plugs and cords.
Duration: 8 hours
Delivery: Full-time or after hours
(after hours course subject to demand)
Course Fee: $194.00
Lighting for Living
Lighting for Living
This is a new innovative training program developed by NECAVIC which will provide training for electrical contractors in the new energy efficiency lighting re-quirements for 6 star housing contained within Sec-tion J of the Building Code of Australia (BCA).
Duration: 1 day (8 hours) or
2 evenings (8 hours)
Delivery: Course delivery mode is
flex-ible with classes scheduled to meet individual needs (subject to demand)
Non-Subsidised Fee: $400.00
Subsidised Fee: $120.00
SHORT COURSES
Understanding Contract Law and
Contracts
- A Practical Guide -
Understanding Contract Law and Contracts This seminar will introduce contractors to some fun-damentals of contract law as well as deliver some practical knowledge in regards to drafting contracts, understanding some of the common clauses in con-tracts typically encountered by contractors, managing risk in contracts, terminating contracts and what to do when a contract is breached.
Duration: 6 hours Delivery: On demand Subsidised Fee: $ 80.00 Non-Subsidised Fee: $400.00 NECA Members Subsidised Fee: $ 40.00 Non-Subsidised Fee: $360.00
Portable Appliance Testing (PAT)
Portable Appliance Testing (PAT)
This course provides information regarding the safe and accurate operation of the Portable Appliance Tester (PAT) and testing of RCDs for persons required to operate this type of equipment. Essentially, the course is aimed at persons who have little or no understanding of electrical theory and are required to endorse equipment as safe to use.
Duration: 16 Hours
Delivery: Full-time/on-site training
available Non-Subsidised Fee: $450.00
Subsidised Fee: $135.00
Cords & Plugs & Portable
Appliance Testing (PAT)
Cords & Plugs & Portable Appliance Testing
This course provides an introduction to flexible cords and plugs and to the operation of the Portable Appliance Tester (PAT) and the testing of RCDs for persons with little or no understanding of electrical theory.
Duration: 16 Hours
Delivery: Full-time/on-site training
available Non-Subsidised Fee: $480.00
ACMA Recognised Training Category
5/6/7 and Coaxial Endorsements
UEENEEF104A Category 5/6/7 and CoaxialEndorsements
This course is an extension of the ACMA Open Ca-bler Registration training course and provides appli-cants with the training, skills and knowledge re-quired to correctly install and terminate Category 5/6/7 structured and Coaxial cabling.
Duration: 2 days
Delivery: Full time
Non-NECA Member Course Fee: $600.00
NECA Member Course Fee: $360.00
ACMA Restricted Cabling
Registration
ACMA Restricted Cabling Registration Course Provides the off-the-job training required to apply for ACMA Restricted Cabling registration. Suitable for persons working as security alarm installers.
Duration: 20 hours
Delivery: Full/Part-time
(subject to demand)
Course Fee: $486.00
UEENEEF105A Optical Fibre
UEENEEF105A Optical FibreThis module provides the student with the knowledge and skills required to correctly install and terminate fibre optic cable.
Duration: 16 hours
Delivery: Full-time: 2 days,
Part-time: 4 evenings plus one Saturday
Course Fee: $750.00
Subsidised Fee: $510.00
ACMA Open Cabling Training
Requirements UEENEEF102A
UEENEEF102A
ACMA Open Cabling Training Requirements
This skill set provides the training, skills and knowledge rec-ognised by registrars for an Australian Communications Me-dia Authority (ACMA) Open Cabling Registration.
Duration: 5 days
Delivery: Full time
Non-Subsidised Fee: $780.00
Subsidised Fee: $280.00
ACMA Registration Conversion Course
Delivers Restricted Cablers with the skills to qualify for an upgrade of their ACMA Registration to an ‘open’ status.
Duration: 36 hours (subject to demand)
Course Fee: $696.00
ACMA Registration Conversion Course
ACMA Open Cabling RegistrationAfter Hours Course
Provides the manual and theoretical skills required by electrical tradespersons seeking ACMA Open Cabling registration.
Duration: 2 nights a week for 5 weeks
Plus 2 Saturdays
Delivery: After hours
(subject to demand)
Course Fee: $846.00
Non-Subsidised Fee: $846.00
ACMA Open Cabling Registration
After Hours
ACMA Restricted Cabling Registration -
Existing Operators
ACMA Restricted Cabling Registration Course Existing Operators
For ‘A’ grade electricians or experienced security/fire system installers who have 6-12 months telecommu-nications cabling experience. Offers off the job training to apply for ACMA Restricted Cabling Regis-tration. Duration: 28 hours Delivery: Full/Part-time (subject to demand) Course Fee: $486.00
TELECOMMUNICATION CABLING
Checking and Testing an
Electrical Installation
Checking and Testing an Electrical Installation
Refresher course to update qualified electricians in the current testing procedures, in terms of WA Electrical Requirements and compliance with Aus-tralian Standards. Duration: 8 hours Delivery: Full-time (subject to demand) Subsidised Fee: $90.00 Non-Subsidised Fee: $300.00
Senior First Aid Refresher
Training
Senior First Aid Refresher Training
The aim of this course is to refresh and reac-credit skills and knowledge gained in Senior First Aid. A current Senior First Aid text book supplied to the participant for pre-reading to update knowledge. Participants then attend an 8 hour day which concentrates on skills and the more important aspects of theory. A full Senior First Aid theory assessment is then undertaken.
Duration: 8 hours
Delivery: Full-time: 1 day
Subsidised Fee: $45.00
Non-Subsidised Fee: $150.00