6 LED colours: White Blue Green Red Yellow Amber

(1)

BEST SUPPLY LTD.

Unit 1602, 16/F., Kowloon Buildi ng, 555 Nathan Road, Yau Ma Tei, Kowloon, Hong Kong Tel: +852-25200086 Fax: +852-25200071Email: china1@bestsupply.com.hk

(2)

Illuminated contours can be found in many places on

petrol stations and buildings of industrial, commercial

and service companies.

Such light bands visually emphasize the contours of

a building during the “darker” times of the day from

dusk right into the night.

Light contours make buildings stand out from their

surrounding and attract attention.

Uniform, “seamless” light without dark areas

Continuous illuminated lines around edges and

corners

Considerable energy savings against fluorescent

lamps or neon tubes (approx. 6 Watts/metre)

Easy and inexpensive installation

Designed for harsh environments

All technical equipment is installed in the base

(lower part), i.e. no additional transformers required

Up to 150 m with one single supply point

The experience that coloured light increases the

observer’s attention formed the basis for the

development of our LED Profile.

The individual elements of the profile can be mounted seamlessly to each other creating a continuous light band with a height of 5 cm.

Please contact us for further details and advice!

Blue

White

Yellow

Amber

Red

Green

6 LED colours:

Proven LED technology with LED tube

Available covers (upper part):

Transparent white (GS 010 similar)

This cover can be fitted with translucent adhesive foil to obtain a variety of additional colours.

White (GS 072 similar)

Blue (GS 612 similar)

Red (GS 2713 similar)

Green (GS 702 similar)

Yellow (GS 304 similar)

Mixed colours based on two LED colours and RGB colour mixture can also be supplied.

Please ask for details.

(3)

LED tube

Sectional view (actual size)

Visible (cover) made of white or coloured acrylic plastic upper part The (base) consists of white ABS plastic lower part 53 mm 51mm 2 2

Converter and electrical circuitry

The LEDs are operated in series connection with the current and voltage being supplied by a special converter converting the 230V mains voltage into a DC voltage of 310V (max.).

Up 150 metres of LED Profile can be operated with one single 230V mains supply point (230V).

The LEDs and the converter form a closed electric circuit, which is pre-assembled in the base of the profile. The individual elements available in lengths of 0.5, 1.0 or 2.0 metres can be combined to form a continuous illuminated line of any length.

The only electrical installation work required is to connect the two leads between the individual elements (e.g. using screwless Wago terminals). All the other wiring has already been done in the factory.

230 Volts

+

__

230 Volts Converter Converter

(to next converter) (from previous converter)

LED tube LED tube

Energy consumption:

Power demand per metre LED Profile (approx. values): LED distance:

2 cm White / blue / green:

Red / yellow / amber:

6 Watts/m

5 Watts/m LED colour

View inside the profile

Upper part (cover) Lower part (base) LED tube Holding clips Converter

Components of the LED Profile

Plastic profile

Lower part (base): white extruded ABS plastic profile. It pre-assembled and contains the electrical internals, i.e. LEDs, converter and cabling.

will be

delivered also

Upper part (cover): extruded profile made of acrylic (PMMA) with a slightly structured surface, available in different colours. The acrylic material has a very good optical scattering charac-teristic and converts the punctual LED light into a shadow-free light band.

LED tube

The LED tube serves as the light source and consists of up to 50 series-connected light-emitting diodes (LEDs).

This chain of LEDs is enclosed in a transparent shrink-down plastic tube protecting it against atmospheric influence.

Converter

Special electronic ballast for the LED tube converting the mains voltage into the required LED current. The LED Profile is equipped with a tubular converter specially designed for the restricted mounting conditions inside the profile.

End caps

End pieces to close the open ends of the profile, available in different colours matching the upper part of the profile.

Mounting brackets for profile base

The spring steel mounting brackets allow safe and efficient mounting of the profile onto building walls.

Holding clips for LED tube

Snap-in-type plastic clips holding the LED tube and the cables in place. The clips allow the LED tube to be removed for length adjustments and perfect fitting on site.

(4)

Efficient installation on facades

Then the profile bases are fixed by simply clamping them into the mounting brackets (screwless mounting).

Now the factory-prepared mains cables can be connected using Wago terminals (through-connection of the mains voltage).

The LEDs can now be switched on for a check.

Wall Wall Wall Mounting bracket made of stainless spring steel

Mitre cutting for edges and corners

This model shows the possible 90° mitre angles at a glance!

External edge

Internal edge

90° angle in the same plane Usually, light bands on buildings not only consist of straight sections but also go round corners and edges.

The LED tube can easily be laid around edges. This requires mitre cuts in the visible upper part of the profile (cover).

The mitre cuts should be made on site where the exact lengths can be checked. The precision of a craftsman’s portable electric mitre saw is sufficient for this job.

Most edges are right-angled, but other angles can also be implemented. An example for a 120° edge can be seen on the front page of this brochure (showing the entrance to the Hansen Neon company building).

First, the mounting brackets are fixed to the wall along the centre line of the future light band using plugs and screws. The distance between the brackets should be 50cm.

The brackets are equipped with long holes to compensate for any drilling inaccuracies.

Wall

When the connection is made, the covers can be pressed onto the bases. If the profile goes round edges, the cover has to be mitred accordingly.

Finally, the open ends of the profile are closed with the end caps.

This makes the installation as easy as this:

For this purpose, we have developed a mounting system with special mounting brackets.

Mounting surface for the LED Profile, e.g. a sheet metal wall

Electrical installation

Two notches facilitate positioning of the drill

After the base has been fixed and the electrical connection is made, the cover is pressed onto the base (no tools required). The LED profile can be wall-mounted by fixing the base

using standard tapping, spax or mounting screws.

The LED Profile can easily and cost-efficiently onto building walls and facades.

be mounted

The LED Profile will be delivered as individual elements with the LED tube and the converter already installed in the base. There are two leads on either end of the profile to connect the profile to the voltage supply and the individual elements with each other (through-connection). All electrical connections are made by srewless Wago terminals.

Universal installation

Then, the electrical connection is made (see above).

Finally, the cover is pressed onto the base. Additional mitring may be necessary in corners and on edges (see below).

(5)

Blue Green Red Yellow Amber 6 6 5 5 5 White White White White White 5 5001 116-050 5 5001 115-050 5 5001 112-050 5 5001 114-050 5 5001 113-050 5 5001 116-100 5 5001 115-100 5 5001 112-100 5 5001 114-100 5 5001 113-100 5 5001 116-200 5 5001 115-200 5 5001 112-200 5 5001 114-200 5 5001 113-200 Night effect: coloured Day effect: white

The LED Profile is supplied as individual pre-assembled elements (including converter and cover).

Profile - base (lower part)

Article no. 5 5000 021

Spring steel mounting bracket

Article no. 5 5000 026 LED light colour Blue Green Red Yellow Amber Power/m (Watts) 6 Article no. 2m element 5 5000 116-200 5 5000 115-200 5 5000 112-200 5 5000 114-200 5 5000 113-200 Article no. 1m element 5 5000 116-100 5 5000 115-100 5 5000 112-100 5 5000 114-100 5 5000 113-100 Article no. 0.5m element 5 5000 116-050 5 5000 115-050 5 5000 112-050 5 5000 114-050 5 5000 113-050 6 5 5 5 Cover colour Blue Green Red Yellow Amber

Night effect: coloured Day effect: coloured

6 6 White Transparent white White White 5 5001 119-050 5 5002 119-050 5 5001 119-100 5 5002 119-100 5 5001 119-200 5 5002 119-200 Night effect: white Day effect: white

With adhesive translucent foil: Night effect: coloured Day effect: coloured

Profile - cover (upper part)

Blue White Green Red Yellow Amber 5 5000 016-100 5 5000 099-100 5 5000 019-100 5 5000 115-100 5 5000 112-100 5 5000 114-100 5 5000 118-100 0.5 metre 1.0 metre 2.0 metres

Special lengths and fitting

pieces available on request!

Transparent white

Profil - end caps

Article no. 5 5000 0xx *)

Converter

*) Please specify the colour when ordering. Available in black, white or the colour of the

respective cover.

Designation Article no.

Colour: white LED distance: 2cm 0.5m/ 25 LEDs 1.0m/ 50 LEDs Wh / Bl / Gr Type C 60 P C 90 P Article no. 5 2302 060 5 2302 090 Rd / Ye / Am Wh / Bl / Gr Rd / Ye / Am

LED Profile (ready for connection)

Wavelength (nm) 460 515 630 590 610 460 515 630 590 610 Designation Designation Profil - end caps Spring steel mounting bracket

Profile - base Designation