• No results found

CRIE3-5 AN-P-I-E-HQQE 1x HZ

N/A
N/A
Protected

Academic year: 2021

Share "CRIE3-5 AN-P-I-E-HQQE 1x HZ"

Copied!
17
0
0

Loading.... (view fulltext now)

Full text

(1)

GRUNDFOS

DATA BOOKLET

CRIE3-5 AN-P-I-E-HQQE 1x200-240 60HZ

Grundfos pump 98389790

Thank you for your interest in our products. Please contact us for more information, or visit our website

https://www.lenntech.com/grundfos/CRIE03/98389790/CRIE-3-5-AN-P-I-E-HQQE.html

info@lenntech.com

tel. +31 152 610 900

fax. +31 152 616 289

(2)

Position Qty. Description

1 CRIE 3-5 N-P-A-E-HQQE

Note! Product picture may differ from actual product

Product No.: On request

Vertical, multistage centrifugal pump with inlet and outlet ports on same the level (inline). Pump materials in contact with the liquid are in stainless steel. A cartridge shaft seal ensures high reliability, safe handling, and easy access and service. Power transmission is via a rigid split coupling. Pipe connection is via PJE (Victaulic®) couplings.

The pump is fitted with a 1-phase, fan-cooled, permanent-magnet, synchronous motor. The motor efficiency is classified as IE5 in accordance with IEC 60034-30-2.

The motor includes a frequency converter and PI controller in the motor terminal box. This enables continuously variable control of the motor speed, which again enables adaptation of the performance to a given requirement. An operating panel on the motor terminal box enables setting of required setpoint as well as setting of pump to "Min." or "Max." operation or to "Stop". The Grundfos Eye indicator on the operating panel provides visual indication of pump status:

• "Power on": Motor is running (rotating green indicator lights) or not running (permanently green indicator lights)

• "Warning": Motor is still running (rotating yellow indicator lights) or has stopped (permanently yellow indicator lights)

• "Alarm": Motor has stopped (flashing red indicator lights).

Communication with the pump is possible by means of Grundfos GO Remote (accessory). The remote control enables further settings as well as reading out of a number of parameters such as "Actual value", "Speed", "Power input" and total "Power consumption".

The terminal box has a number of inputs and outputs enabling the motor to be used in advanced applications where many inputs and outputs are required:

• two dedicated digital inputs

• three analog inputs, 0(4)-20 mA, 0-5 V, 0-10 V, 0.5 - 3.5 V; the factory-fitted pressure sensor is connected to one of these inputs

• 5 V voltage supply to potentiometer and sensor • one analog output, 0-10 V, 0(4)-20 mA

• two configurable digital inputs or open-collector outputs • two Pt100/Pt1000 inputs

• LiqTec, dry-running protection sensor input • Grundfos Digital Sensor input and output • 24 V voltage supply for sensors

• two signal-relay outputs (potential-free contacts) • GENIbus connection

• interface for Grundfos CIM fieldbus module.

Further product details

The pump is equipped with a pressure sensor registering pump outlet pressure and enabling controlled pump operation based on constant pressure.

An operating panel on the motor terminal box enables setting of required setpoint as well as setting of pump to "Min." or "Max." operation or to "Stop". The Grundfos Eye indicator on the operating panel provides visual indication of pump status:

• "Power on": Motor is running (rotating green indicator lights) or not running (permanently green indicator lights)

• "Warning": Motor is still running (rotating yellow indicator lights) or has stopped (permanently yellow indicator lights)

(3)

Position Qty. Description

• "Alarm": Motor has stopped (flashing red indicator lights).

Communication with the pump is possible by means of Grundfos GO Remote (accessory). The remote control enables further settings as well as reading out of a number of parameters such as "Actual value", "Speed", "Power input" and total "Power consumption".

Steel, cast iron and aluminium components have an epoxy-based coating made in a cathodic electro-deposition (CED) process. CED is a high-quality dip-painting process where an electrical field around the products ensures deposition of paint particles as a thin, well-controlled layer on the surface. An integral part of the process is a pretreatment. The entire process consists of these elements: 1) Alkaline-based cleaning.

2) Zinc phosphating.

3) Cathodic electro-deposition.

4) Curing to a dry film thickness 18-22 my m.

The colour code for the finished product is NCS 9000/RAL 9005.

Pump

A standard split coupling connects the pump and motor shaft. It is enclosed in the pump head/motor stool by means of two coupling guards.

The pump head and flange for motor mounting is made in one piece (cast iron). The pump head cover is a separate component (stainless steel). The pump head has a combined 1/2" priming plug and vent screw.

The pump is fitted with a balanced O-ring seal unit with a rigid torque-transmission system. This seal type is assembled in a cartridge unit which makes replacement safe and easy. Due to the balancing, this seal type is suitable for high-pressure applications. The cartridge construction also protects the pump shaft from possible wear from a dynamic O-ring between pump shaft and shaft seal.

Primary seal:

• Rotating seal ring material: silicon carbide (SiC) • Stationary seat material: silicon carbide (SiC)

This material pairing is used where higher corrosion resistance is required. The high hardness of this material pairing offers good resistance against abrasive particles.

Secondary seal material: EPDM (ethylene-propylene rubber)

EPDM has excellent resistance to hot water. EPDM is not suitable for mineral oils.

The shaft seal is screwed into the pump head.

The chambers and impellers are made of stainless-steel sheet. The chambers are provided with a PTFE neck ring offering improved sealing and high efficiency. The impellers have smooth surfaces, and the shape of the blades ensure a high efficiency.

(4)

Position Qty. Description

The pump has a stainless-steel base mounted on a separate base plate. The base and base plate are kept in position by the tension of the staybolts which hold the pump together. The outlet side of the base has a combined drain plug and bypass valve. The pump is secured to the foundation by four bolts through the base plate. The base is prepared for connection by means of PJE (Victualic®) couplings.

Motor

The motor is a totally enclosed, fan-cooled motor with principal dimensions to IEC and DIN standards. The motor is flange-mounted with tapped-hole flange (FT).

Motor-mounting designation in accordance with IEC 60034-7: IM B 14 (Code I) / IM 3601 (Code II). Electrical tolerances comply with IEC 60034.

The motor efficiency is classified as IE5 in accordance with IEC 60034-30-2.

The motor requires no external motor protection. The motor control unit incorporates protection against slow- and quick-rising temperatures, e.g. constant overload and stalled conditions.

Technical data

Controls:

Frequency converter: Built-in

Pressure sensor: Y

Liquid:

Pumped liquid: Water

Liquid temperature range: -20 .. 120 °C Liquid temperature during operation: 20 °C

Density: 998.2 kg/m³

Technical:

Rated flow: 3.5 m³/h

Rated head: 34 m

Pump orientation: Vertical Shaft seal arrangement: Single Code for shaft seal: HQQE Approvals on nameplate: CE, EAC,ACS Curve tolerance: ISO9906:2012 3B

Materials:

Base: Stainless steel

EN 1.4408 AISI 316

Impeller: Stainless steel

EN 1.4301 AISI 304

Bearing: SIC

Installation:

Maximum ambient temperature: 50 °C Maximum operating pressure: 25 bar

Max pressure at stated temp: 25 bar / 120 °C 25 bar / -20 °C Type of connection: PJE

Size of inlet connection: DN 32 1 1/4 inch Size of outlet connection: DN 32

1 1/4 inch Pressure rating for pipe connection: PN 50

(5)

Position Qty. Description

Flange size for motor: FT100

Electrical data:

Motor standard: IEC

Motor type: 80A

IE Efficiency class: IE5 Rated power - P2: 0.75 kW Power (P2) required by pump: 0.75 kW Mains frequency: 50 Hz Rated voltage: 1 x 200-240 V Rated current: 4.70-3.90 A Cos phi - power factor: 0.99

Rated speed: 360-4000 rpm

Efficiency: 85.2%

Motor efficiency at full load: 85.2 % Enclosure class (IEC 34-5): IP55 Insulation class (IEC 85): F

Others:

Minimum efficiency index, MEI ≥: 0.7

Net weight: 21.5 kg

Gross weight: 24.4 kg

(6)

On request CRIE 3-5 N-P-A-E-HQQE 50 Hz

H [m] 0 5 10 15 20 25 30 35 40 45 50 Q [m³/h] 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 eta [%] 0 10 20 30 40 50 60 70 80 90 100 CRIE 3-5, 1*230 V 100 % 90 % 80 % 70 % 60 % 50 % 40 % 21 % P [W] 0 200 400 600 800 NPSH [m] 0 2 4 6 8 P1 (motor+freq.converter) P2

(7)

H [m] 0 5 10 15 20 25 30 35 40 45 50 Q [m³/h] 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 eta [%] 0 10 20 30 40 50 60 70 80 90 100 CRIE 3-5, 1*230 V 100 % 90 % 80 % 70 % 60 % 50 % 40 % 21 % P [W] 0 200 400 600 800 NPSH [m] 0 2 4 6 8 P1 (motor+freq.converter) P2 210 150 120 214 299 G 1/2 G 1/2 G 1/2 50 100 13 x 4 42.2 22 158 122 180 210 3 15 8 26 23 25 24 7 21 20 22 B Y 6 5 2 4 10 A +24 V* 1 14 9 12 17 19 11 18 +24 V*OC DI +24 V* AI2 GDS RX GDS TX GND GENIbus A GENIbus B +24 V GND GENIbus Y GND DI1 AI1 DI3/OC1 LiqTec AI3 GND DI2 LiqTec GND AO Pt100/1000 Pt100/1000 DI4/OC2 GND +24 V*OC GND DI NC C2 NO NC C1 NO +24 V* +24 V* +24 V*/5 V* N L N L PE +24 V* +24 V*/5 V* +24 V* +24 V*/5 V* +5 V* +5 V +24 V +5 V +5 V* Description Value General information:

Product name: CRIE 3-5 N-P-A-E-HQQE

Product No: On request

EAN number: On request

Technical:

Rated flow: 3.5 m³/h

Rated head: 34 m

Stages: 5

Impellers: 5

Number of reduced-diameter impellers: 0

Low NPSH: N

Pump orientation: Vertical

Shaft seal arrangement: Single

Code for shaft seal: HQQE

Approvals on nameplate: CE, EAC,ACS

Curve tolerance: ISO9906:2012 3B

Pump version: N

Model: A

Materials:

Base: Stainless steel

EN 1.4408 AISI 316

Impeller: Stainless steel

EN 1.4301 AISI 304

Material code: A

Code for rubber: E

Bearing: SIC

Installation:

Maximum ambient temperature: 50 °C Maximum operating pressure: 25 bar

Max pressure at stated temp: 25 bar / 120 °C 25 bar / -20 °C

Type of connection: PJE

Size of inlet connection: DN 32 1 1/4 inch Size of outlet connection: DN 32

1 1/4 inch Pressure rating for pipe connection: PN 50 Flange size for motor: FT100

Connect code: P

Liquid:

Pumped liquid: Water

Liquid temperature range: -20 .. 120 °C Liquid temperature during operation: 20 °C

Density: 998.2 kg/m³

Electrical data:

Motor standard: IEC

Motor type: 80A

IE Efficiency class: IE5

Rated power - P2: 0.75 kW

Power (P2) required by pump: 0.75 kW

Mains frequency: 50 Hz

Rated voltage: 1 x 200-240 V

Rated current: 4.70-3.90 A

Cos phi - power factor: 0.99

Rated speed: 360-4000 rpm

Efficiency: 85.2%

Motor efficiency at full load: 85.2 % Enclosure class (IEC 34-5): IP55 Insulation class (IEC 85): F

Motor protec: YES

Motor No: 98248266 Controls: 210150 120 G 1/2G 1/2 G 1/2100 13x4 158122 180210

(8)

Description Value

Control panel: Standard

Function Module: FM300 - Advanced

Frequency converter: Built-in

Pressure sensor: Y

Others:

Minimum efficiency index, MEI ≥: 0.7

Net weight: 21.5 kg

Gross weight: 24.4 kg

(9)

On request CRIE 3-5 N-P-A-E-HQQE 50 Hz

cos phi eta 0.0 0.2 0.4 0.6 0.8 P2 [kW] 0 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 I [A] 0.0 1.0 2.0 3.0 4.0 CRIE3-5 + 80A 0.75 kW 1*230 V, 50 Hz eta cos phi I n [rpm] 0 1000 2000 3000 P1 [kW] 0.0 0.4 0.8 1.2 n P1 (motor+freq.converter) n = 100 %

(10)

On request CRIE 3-5 N-P-A-E-HQQE 50 Hz

Note! All units are in [mm] unless others are stated.

Disclaimer: This simplified dimensional drawing does not show all details.

210

150

120

214

299

G 1/2

G 1/2

G 1/2

50

100

13

x

4

42.2

22

158

122

180

210

(11)

Exploded view

301a 219 92 7 7a 77 301a 92 11 9 51 100 49 105 45 215a 215 18 217 215a 534a 534531 531a 28 17 251d 251a 6 11b 66a 67 530 530a

(12)

Sectional drawing (TM058200 for TPE2,TPE3)

4

2

1

3

5

TM058200

(13)

Exploded view ( TM057026 for MGE model H/I )

251d 251b 290 287 277a 286 277 273a 273 268 268a 289a 289 288b 288 288a 251a 252b 156c 159d 156b 156d 188 275a 153 154 158 178 185 192 191 159e 156c 156 151 152 266 187 291 293 252a 172 150 287a 502 273b 157

(14)

Parts list CRIE 3-5, Product No. On request

Valid from 25.12.2012 (1252)

Pos Description Annotation Données de classification Référence Quantité Unité

- Motor 1 pcs

Terminal 3

Pan head thread forming screw 4

150 Stator housing 1

150 Stator 1

151 Fan cover 1

152 Pan head thread forming screw 6

152 Pan head thread forming screw 1

152 Pan head thread forming screw 4

152 Pan head thread forming screw 1

153 Ball bearing Designation: 6204.2Z.C3.SYN 1

154 Ball bearing Designation: 6204.2Z.C3.SYN 1

156 Fan 1

156b Flange 1

156d Gasket Internal diameter: 114,80 1

Outer diameter: 121,20 Thickness: 0,25 157 O-ring Diameter: 47 1 Material type: NBR Thickness: 3 158 Waved washer 1 159c Seal ring 1 159c Seal ring 1 172 Shaft w/rotor 1 173a Base 1

185 Cross recess Pan head screw 4

186 Drain plug 1

203 Terminal plug 1

251a Control box 1

251b Control box 1

251d Pan head thread forming screw 4

266 Connector plug 3-pole 1

266 Connector plug 3-pole 1

266 Connector plug 8-pole 1

266 Connector plug 8-pole 1

266 Connector plug 8-pole 1

266 Connector plug 2-pole 1

266 Connector plug 10-pole 1

268 Pan head screw 1

273 Funct. Module cpl. 1

273b Battery 1

275a Pin 1

277 Isolation cover 1

277a Cross recess Pan head screw 1

277a Cross recess Pan head screw 4

277a Cross recess Pan head screw 1

286 Spacer 1 287 Cover 1 288 Wire clamp 3 288b Washer 6 289 Wire clamp 1 290 Control panel, cpl. 1 300 Plug cpl. 4 301 Jumper 1 - Base cpl. 1 pcs 6 Base 1 25 Plug 2 56 Base plate 1 Pressure transmitter 1 pcs

(15)

Pos Description Annotation Données de classification Référence Quantité Unité

- Sealing parts 1 pcs

- 25 Drain plug w/bypass valve 1

38 O-ring Diameter: 16,3 1

Material type: EPDM Thickness: 2,4

37 O-ring 2

100 O-ring Diameter: 16,3 2

Material type: EPDM Thickness: 2,4

- 2 Pump head cpl. 1 pcs

2 Pump head 1

7 Coupling guard 2

7.a Combi Slot Torx screw 4

- 18 Air vent screw 1

Plug 1

Spindle 1

28 Hex head screw Length (mm): 25 MM 4

Thread: M6

60 Formed wire spring 1

77 Pump cover 1

- 8 Coupling cpl. 1 pcs

9 Hex socket head cap screw Designation: DIN 912 4

Length (mm): 20 Thread: M6

10 Shaft pin Diameter: 5 1

Length (mm): 26

10a Coupling half 2

26 Staybolt Length (mm): 187 4 pcs

Thread: M12

36a Washer Designation: DIN 125 A 4 pcs

Internal diameter: 13 Outer diameter: 24 Thickness: 2,5

55 Outer sleeve 1 pcs

66a Nut Thread: M12 4 pcs

- 80 Chamber stack 1 pcs - 4 Chamber cpl. 3 Guide vane 6 Plate 1 Retainer 1 Intermediate chamber 1 Vane 1 45 Neck ring 1 65 Retainer 1 - 4a Chamber w. bearing cpl. 1 Guide vane 6

Retainer for bearing 1

Bearing bush 1 Retainer 1 Intermediate chamber 1 Vane 1 45 Neck ring 1 65 Retainer 1 - 5a Chamber cpl. 1 Retainer 1 Intermediate chamber 1 Vane 1 45 Neck ring 1 65 Retainer 1

36 Lock nut Thread: M8 1

47a Bearing ring, rotating 1

49 Impeller cpl. 5

- 50a Guide vane cpl. 1

(16)

Pos Description Annotation Données de classification Référence Quantité Unité

Plate 1

50b Top plate 1

51 Shaft, spline, cpl. 1

64a Spacing pipe 3

64a Spacing pipe Internal diameter: 12,85 1

Outer diameter: 15,85 Length (mm): 4,50

64c Clamp, splined Internal diameter: 8,5 1

Outer diameter: 15

66 Wedge lock washer 1

- 105 Shaft seal Material type: HQQE 1 pcs

O-ring 1

O-ring 1

Seal driver, upper 1

Seal driver, lower 1

Spacer ring 1

Pipe 1

Plug 1

Plug 1

Compression spring 1

Socket set screw 1

102 O-ring Diameter: 22,00 1

Material type: EPDM Thickness: 2,75

103 Seal ring, stationary 1

105 Seal ring, rotating 1

107 O-ring 1

(17)

Disclaimer: The information about the Grundfos pump in this document may be outdated. Data may be subject to alterations without further notice.

Please contact us to verify the data above is still accurate/up-to-date. All information is copyright Grundfos.

info@lenntech.com https://www.lenntech.com

tel. +31 152 610 900 fax. +31 152 616 289

References

Related documents

[r]

[r]

[r]

university reform claims that strategic manage- ment has been strengthened in the universities, while the role of university per- sonnel has remained weak. Two major strategy

In this review, the research carried out using various ion-exchange resin-like adsorbents including modified clays, lignocellulosic biomasses, chitosan and its derivatives, microbial

While in Table 3 we present a pooled specification, to increase the chances for the added variables to exert a significant impact, in unreported regressions we repeat the

In addition to the siren chirps the status Indicator will be flashing rapidly to Indicate that the alarm has been tripped (also see "Visual alarm status indicator', page 4),

Our approach differs from those available in the literature, as we do not seek a better analytic expression for the implied volatilities from the SABR model; instead, we project,