RENR8172-03
January 2008
D6R III Track-Type Tractor
Electrical System
with AccuGrade
Volume 1 of 3: Chassis Diagram
©
2008 Caterpillar, All Rights Reserved
Printed in U.S.A.
EXW1-UP
WRG1-UP
DMK1-UP
LGP1-UP
HKE1-UP
RFC1-UP
HDC1-UP
MTJ1-UP
WCB1-UP
DLM1-UP
HCD1-UP
GMT1-UP
TBC1-UP
JEK1-UP
GJB1-UP
JDL1-UP
LFM1-UP
EXL1-UP
MRT1-UP
DPS1-UP
1
2
200-L32 BK-14
AG-C4
111-7898
L-C12
3E-5179
C-C4
130-6795
9X-1123
Component
Part Number
Single Wire
Connector
Socket
Pin
AG-C3
130-6795
Pin or Socket
Number
Wire, Cable, or Harness Assembly Identification:
Includes Harness Identification Letters and Harness
Connector Serialization Codes Harness Connector Serialization Code: The "C" stands
for "Connector" and the number indicates which
connector in the harness. (C1, C2, C3, ...)
Part Number For
Connector Recepticle
Part Number for
Connector Plug
Harness Identification Letter(s):
(A, B, C, ..., AA, AB, AC, ...)
Plug
Ground
Connection
325-AG135 PK-14
Circuit Identification
Number Wire Color Wire Gauge
Harness identification code:
This example indicates wire
135 in harness "AG".
Receptacle
Pressure
Symbol
T
Temperature
Symbol
Level
Symbol
Flow
Symbol
Circuit Breaker
Symbol
Harness and Wire Symbols
1
1
2
2
Sure-Seal connector: Typical representation
of a Sure-Seal connector. The plug and receptacle
contain both pins and sockets.
Deutsch connector: Typical representation
of a Deutsch connector. The plug contains all
sockets and the receptacle contains all pins.
Symbols
Symbols and Definitions
Harness And Wire Electrical Schematic Symbols
Fuse
(5 Amps)
5A
Fuse: A component in an electrical circuit that will open the circuit if too much current flows
through it.
Switch (Normally Open): A switch that will close at a specified point (temp, press, etc.). The
circle indicates that the component has screw terminals and a wire can be disconnected from it.
Switch (Normally Closed): A switch that will open at a specified point (temp, press, etc.).
No circle indicates that the wire cannot be disconnected from the component.
Ground (Wired): This indicates that the component is connected to a grounded wire. The
grounded wire is fastened to the machine.
Ground (Case): This indicates that the component does not have a wire connected to ground.
It is grounded by being fastened to the machine.
Reed Switch: A switch whose contacts are controlled by a magnet. A magnet closes the
contacts of a normally open reed switch; it opens the contacts of a normally closed reed switch.
Sender: A component that is used with a temperature or pressure gauge. The sender
measures the temperature or pressure. Its resistance changes to give an indication to
the gauge of the temperature or pressure.
T
Relay (Magnetic Switch): A relay is an electrical component that is activated by electricity.
It has a coil that makes an electromagnet when current flows through it. The
electromagnet can open or close the switch part of the relay.
Magnetic Latch Solenoid: A magnetic latch solenoid is an electrical component that is
activated by electricity and held latched by a permanent magnet. It has two coils (latch and unlatch)
that make electromagnet when current flows through them. It also has an internal switch that places
the latch coil circuit open at the time the coil latches.
Solenoid: A solenoid is an electrical component that is activated by electricity. It has a
coil that makes an electromagnet when current flows through it. The electromagnet
can open or close a valve or move a piece of metal that can do work.
RENR8172-03 VOL
1 of 3
36 Page,
(Dimensions: 48 inches x 35 inches)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z aa bb cc dd
34
35
36
37
38
39
40
41
42
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z aa bb cc dd
43
44
45
43
44
45
Component
Schematic
Location
Side View
Coordinate
Top View
Coordinate
Alarm - Backup
A-13
F-12
F-33
Alternator
I-4
X-9
X-32
Batteries
I-7
L-16
L-42
Control - Engine
G-6
S-10
S-38
Diode - A/C
A-5
X-13
X-38
Display - Video Camera
C-11
Q-19
Q-37
Fuse - Prelube
I-3
L-15
L-40
Heater - Jacket Water
D-4
S-12
S-34
Motor - Fuel Priming Pump
H-5
X-16
X-38
Motor - Prelube Pump
H-2
Y-9
Y-33
Motor - ROPS A/C 1
C-14
F-24
F-36
Motor - ROPS A/C 2
C-14
F-24
F-36
Motor - Starter
H-4
S-9
S-38
Radio - Product Link
A-11
H-15
H-36
Relay - Prelube
I-3
R-13
R-34
Relay - ROPS A/C
C-13
F-24
F-36
Resistor - CAN A (1)
C-8
S-12
S-38
Sender - Fuel Level
A-13
F-17
F-36
Sender - Hydraulic Oil Temperature
B-11, C-11
L-16
L-31
Sender - T/C Oil Temperature
B-6
N-9
N-37
Sender - Xmsn Lube Temperature
A-13
G-11
G-34
Sender - Xmsn Sump Temperature
C-6
O-10
O-33
Sensor - Atmospheric Pressure
D-4
R-12
R-37
Sensor - Coolant Temperature
D-4
X-11
X-35
Sensor - Demand Fan Speed
C-6
X-12
X-33
Sensor - Fuel Pressure
F-3
Q-11
Q-36
Sensor - Injection Actuation Pressure
E-4
X-11
X-38
Sensor - Inlet Air Temperature
E-4
T-11
T-37
Sensor - Oil Pressure
D-4
S-9
S-37
Sensor - Speed/Timing A
D-4
W-10
W-37
Sensor - Speed/Timing B
D-4
W-10
W-37
Sensor - T/C Output Speed
B-6
N-9
N-35
Sensor - Transmission Output Speed 1, 2
D-15
G-9
G-36
Sensor - Turbo Inlet Pressure
H-5
W-17
W-37
Sensor - Turbo Outlet Pressure
E-4
T-11
T-37
Solenoid - A/C Clutch
B-5
Y-15
Y-38
Solenoid - Demand Fan
H-5
Y-15
Y-36
Solenoid - Flexxaire Fan
A-5
Y-15
Y-36
Solenoid - Implement Lockout
B-10
N-16
N-30
Solenoid - PAT Left Angle
B-10
N-14
N-29
Solenoid - PAT Right Angle
B-10
N-14
N-29
Solenoid - Start Aid
C-6
T-10
T-39
Solenoids - Injector 1-6
F-3
W-36
W-14
Solenoids - Transmission Clutch
D-15
I-9
I-35
Switch - A/C Refrigerant
B-5
X-13
X-38
Switch - Disconnect
I-8
N-15
N-41
Switch - Flexxaire Fan
A-4
P-18
P-37
Switch - Fuel Priming Pump
H-5
X-16
X-38
Switch - Powertrain Filter Pressure 2
B-11, C-11
N-16
N-30
Switch - Prelube Oil Pressure
H-3
X-12
X-33
Switch - Remote Disconnect
I-8
N-15
N-38
Switch - Underhood Work Light
I-6
U-15
U-38
Timer - Prelube
H-3
R-13
R-34
Video Camera
C-10
G-25
G-35
Vol. 1 Component Location
W ire Description
Wire
Number
Wire
Color
Description
Wire
Number
Wire
Color
Description
101
RD
Bat (+)
F715
PU
User Shutdown
102
RD
Hd Lmp
F716
WH
UserShutdown
103
YL
Rear Floods
F717
YL
Throttle Sw.
104
YL
Aux Ckt 2
F718
BU
Throttle Sw.
105
RD
Key Sw
F719
BR
Crank With Out Injection (N.C)
106
RD
Product Link
F720
GN
Crank With Out Injection (N.O)
108
BU
Wipers
F761
BR
Parking Brake Dump / Service Brake Dump Solenoids
110
RD
Aux Ckt 3
F780
PK
Parking Brake Sw
111
YL
Aux Ckt 1
F781
BR
Downshift Sw
112
PU
Main Power Rly Output
F782
OR
Reverse Sw
113
OR
Opr Mon Panel Vmis B+ Switched
F783
GN
Upshift Sw
114
RD
Warning Horn (forward)
F784
YL
Downshift Sw
115
PK
Front Floods
F785
WH
Upshift Sw
116
RD
Fender Floods
F786
GY
Reverse Sw
118
RD
Seat Compressor Sw.
F788
PU
Left Steer Clutch
124
GN
Blowers
F789
YL
Right Steer Clutch
130
GN
Aux Ckt
F790
BR
Service Brake Pedal
140
BU
Power Train
F792
WH
Left Brake Solenoid
146
RD
Aux Circuit
G730
PK
Park Brake Solenoid
148
RD
Aux Circuit
G731
GY
Secondary Service Brake Solenoid
150
RD
Engine ECM Switched Power
G797
BU
Prelube Relay to Oil Evac Bracket Assembly
158
BR
A/C Condensor
H710
PK
Blade Raise Position Sensor
159
BU
ROPS A/C
H711
GN
Blade Tilt Position Sensor
160
PU
Winch / Seat
H713
PK
Blade Raise Solenoid
174
RD
Video Camera Display
H714
OR
Blade Lower Solenoid
176
YL
Ripper Pin Puller Sw./ Winch Sw. / Seat Suspension
J764
BR
Machine Control 10v Return
184
BU
ARO Connector / Light Bar Connector
J766
PU
Accugrade Joystick Power Return
186
RD
24V - 12V Converter
K757
YL
Blade Rotation Pwm Out
197
RD
Aux Ckt 4
L740
BR
Machine Control Digital Return
198
RD
Service Brake Pedal Sw
N707
PU
Engine Control Switch Return (Not Used)
P726
BU
Winch Control Decode
200
BK
Main Chassis
P727
GY
Winch Control Enable
201
BK
Operator Monitor Return
P728
YL
Winch Control Y Axis
202
BK
Xmsn Ctrl
P729
BR
Winch Control X Axis
216
BK
RH Platform Ground
P731
PU
Winch Filter Status
229
BK
Bat (-)
R746
PK
Turbo Outlet Pressure Sensor
250
BK
Accugrade Buzzer
R747
GY
Atmosphereic Pressure Sensor
270
BK
CMS Ident Code 0
T725
WH
Fuel Differential Pressure Sensor (Not Used)
271
BK
CMS Ident Code 1
T744
WH
Accugrade Blade Control - Switched Pwr 1 Return
272
BK
CMS Ident Code 2
T745
YL
Accugrade Blade Control - Switched Pwr 2 Return
273
BK
CMS Ident Code 3
Y787
WH
CAN D Data Link (+)
274
BK
CMS Ident Code 4
Y788
GY
CAN D Data Link (-)
275
BK
CMS Ident Code 5
851
WH
Hydrst Speed And Direction Sensor
276
BK
Xmsn Ctrl Ident Code 0
880
RD
Accugrade Lazer Display Sw. 1
277
BK
Xmsn Ctrl Ident Code 1
881
BU
Accugrade Lazer Display Sw. 2
278
BK
Xmsn Ctrl Ident Code 2
882
GN
Accugrade Lazer Display Sw. 3
279
BK
Xmsn Ctrl Ident Code 3
883
WH
Accugrade Lazer Display Sw. 4
280
BK
Xmsn Ctrl Ident Code 4
884
BR
Accugrade Lazer Display Sw. 0
290
BK
CMS Service
885
BK
Accugrade Lazer Display Sw. Ground
291
BK
CMS Clear
892
BR
Cat Data Link (-)
A289
BK
Start Aid Solenoid Return
893
GN
Cat Data Link (+)
F846
PU
Unused
301
OR
Starter No. 1 Sol
F848
OR
Bi-Directional Mode Sw. (N.O.)
304
WH
Starter Relay No. 1 Output
F849
WH
Bi-Directional Mode Sw. (N.C.)
306
GN
Starter Relay Coil To Neut Start Sw Or Key Sw
F877
WH
Counter Balance and Boost Relay
307
OR
Key Sw To Neutral Start Sw Or Vmis Sensor Module
G826
BR
Engine Oil Pressure Sensor Power
308
YL
Main Power Relay Coil
G827
BU
Engine Oil Pressure Sensor Return
310
PU
Start Aid Sw To Start Aid Sol
G828
WH
Engine Pressure Sensors +5V
321
BR
Backup Alarm Lamp Travel Alarm
G829
GN
Engine Pressure Sensors Common
322
GY
Warning Horn
G833
PK
Engine Temperature Sensors Return
326
PU
Key Sw 'c' Term.
G849
BR
Engine Injection Actuation Pressure
337
WH
Prelube Pushbutton Sw To Prelube Timer
G850
BU
Inlet Air Heater
G854
PK
HEP Connector
403
GN
Alternator (r) Term.
G855
PU
HEP Connector
410
WH
Opr Mon Fault Alarm
G856
WH
TDC Service Probe (+)
411
PK
Opr Mon Master
G857
YL
TDC Service Probe (-)
419
YL
Opr Mon Parking Brake
H802
GY
Solenoid Return
424
GY
T/C Output Temperature
L856
YL
Ctct Blade Control - Can D Data Link (+)
426
BR
Opr Mon Power Train Oil Filter
L857
GN
Ctct Blade Control - Can D Data Link (-)
442
GY
Hyd System Temp Gage
L870
YL
Ctct Blade Control - Awake
443
YL
Power Train Temp Gage
L871
BU
Ctct Blade Control - Awake Gnd
447
PK
Fuel Level Gage
L872
BU
Ctct Blade Control - Switched Pwr 1
A447
PK
Prelube Press. Sw To Prelube Timer
L873
GY
Ctct Blade Control - Switched Pwr 2
A487
PU
Opr Mon Fault Alarm #2
L874
YL
Ctct Blade Control - Switched Pwr 3
C413
YL
CMS Display Data
T858
GY
Injector Solenoid 1-2 High Side
C414
BU
CMS Display Load
T859
WH
Injector Solenoid 3-4 High Side
E455
BR
Not Used
T860
OR
Injector Solenoid 5-6 High Side
G460
GN
Xmsn Oil Temp. Sensor
900
PU
1st Gear Clutch Solenoid
H416
GN
MVP LED
924
GN
Transmission Solenoid 1-4 Return
H417
OR
NON MVP LED
975
WH
Power Train Solenoid Return
977
YL
Auto-Downshift Sw.
500
BR
Wiper - Front (park)
993
BR
Engine Analog Sensor Return
501
GN
Wiper - Front (low)
994
GY
Oil Pressure (filtered)
502
OR
Wiper - Front (hi)
995
BU
Coolant Temperature
503
BR
Wiper - Rear (park)
997
OR
Engine Analog Sensor Power
504
YL
Wiper - Rear (low)
998
BR
Engine Digital Sensor Return
505
BU
Wiper - Rear (hi)
C912
GN
Not Used
506
PU
Washer - Front
C913
BU
Ground Speed Radar
507
WH
Washer - Rear
C967
BU
Inlet Air Temperature
508
PU
Radio Speaker - Left
C986
BR
Not Used
509
WH
Radio Speaker - Left (commom)
C987
RD
Inlet Air Heater
511
BR
Radio Speaker - Right
C991
PK
Fuel Filter Monitor
512
GN
Radio Speaker - Right (common)
E900
WH
Trans Output Spd +
513
OR
A/C Compressor/Refrigerant Pressure Sw
E901
GN
Trans Output Spd
-515
GY
Blower Motor (hi)
E906
OR
Trans Output Spd Q+
516
GN
Blower Motor (medium)
E907
GY
Trans Output Spd
Q-517
BU
Blower Motor (low)
E908
BR
Trans Input Spd +
521
YL
A/C Sw To Refrigerant Sw
E909
WH
Trans Input Spd
-522
WH
A/C Clutch To Thermostat Sw
E912
PU
Implement Shutoff Switch
523
BR
Wiper - Left (park)
E913
YL
Implement Shutoff Switch
524
BU
Wiper - Left (low)
E918
GN
Implement Shutoff Switch
525
GY
Wiper - Left (hi)
E963
BK
Engine Speed/Timing
A-526
YL
Wiper - Right (park)
E964
WH
Engine Speed/Timing A+
527
GN
Wiper - Right (low)
E965
BU
Engine Speed/Timing
B-528
PK
Wiper - Right (hi)
E966
YL
Engine Speed/Timing B+
529
WH
Washer Left
G939
PK
Power Train Sw. / Sensor Return
530
OR
Washer Right
J943
GN
Blade Control Handle (Left Push Button)
567
WH
A/C Sw Jumper
J944
BU
Blade Control Handle (Left Push Button)
573
GN
Blade Float Indicator LED
J945
WH
Blade Control Handle (Right Push Button)
592
BU
DC/DC Converter Power Output
J946
OR
Blade Control Handle (Right Push Button)
593
GN
Condensor Fan Relay To Motors
J950
PU
Left Lift Cylinder Position (Not Used)
A513
PK
DC/DC Converter Memory Output
K960
PK
CAN Data Link B (+)
A557
WH
Precleaner Blower +B
K961
GN
CAN Data Link B (-)
Power Circuits
Control Circuits
Ground Circuits
Basic Machine Circuits
Monitoring Circuits
Accessory Circuits
C568
WH
Blower Motor (max)
K978
BU
Priority Valve Solenoid
C569
YL
20A Converter +12v Output
L997
BU
Demand Fan Speed Sensor
E555
OR
20A Converter +12v Memory
M919
BU
Main Pump Pressure Sensor
M927
GN
Implement Shutoff Solenoid
600
BR
Dash Lamp Basic
M928
BU
Right Tilt Valve
608
GN
Flood Lamp - Rear
M929
WH
Left Tilt Valve
609
YL
Flood Lamp - Side
N942
OR
Flexxaire Fan Sw.
610
OR
Head Lamp Basic
N957
PK
Accugrade GPS (RS 232 TXD 0)
625
PK
Underhood Worklight
N958
PK
Accugrade GPS (RS 232 TXD 2)
630
GY
Flood Lamp Rear (attach)
N960
OR
Accugrade GPS (RS 232 RXD 0)
651
PK
Flood Lamp Rear
N961
OR
Accugrade GPS (RS 232 RXD 2)
663
GY
Gage Lamps - Smart Ems
N967
GY
Accugrade GPS (RS 232 CTS 0)
N970
YL
Accugrade GPS (RS 232 RTS 0)
709
OR
Sensor Power Supply
N973
BR
Accugrade GPS (RS 232 CTS 0)
751
GN
Xmsn Shift Sol No. 1 Or 3
N976
PU
Accugrade GPS (RS 232 RTS 0)
752
YL
Xmsn Shift Sol No. 2
T901
YL
MSS Exciter Coil
754
BU
Xmsn Shift Sol No. 3 Or 1
T902
PK
MSS Exciter Coil
755
OR
Xmsn Shift Sol No. 4 Or 5
T951
YL
Inj 1 Hi-side
779
WH
Coupler Engage Sol
T952
BR
Inj 2 Hi-side
780
PU
Coupler Disengage Sol
T953
BU
Inj 3 Hi-side
A700
OR
Digital Sensor Power(+8v)
T954
GY
Inj 4 Hi-side
A751
YL
Fuel Temperature Sensor (Not Used)
T955
GN
Inj 5 Hi-side
A757
GY
Not Used
T956
GY
Inj 6 Hi-side
A758
BR
Not Used
T957
PU
Inj 1 Return
C720
BU
Winch Control Relay Sinking Driver (Not Used)
T958
YL
Inj 2 Return
E707
GN
CMS Display +V
T959
BR
Inj 3 Return
E708
PK
CMS Display Clock
T960
BU
Inj 4 Return
E735
PU
Operator Sw. Input
T961
GN
Inj 5 Return
E752
YL
Accugrade Lightbars
T962
WH
Inj 6 Return
E753
WH
Accugrade Lightbars
T964
OR
Product Link (RS 232 Port 1 TXD)
E799
BR
Demand Fan Solenoid Return
T965
GN
Product Link (RS 232 Port 1 RXD)
F700
BU
Demand Fan Solenoid
T966
BK
Product Link (RS 232 Port 1 GND)
F702
GN
Decel Pedal Position Sensor
T968
WH
Prelube Oil Evac Pump
F708
YL
Flexxaire Fan Pull Solenoid
T993
BR
Winch Control +5v Power Return
F709
BU
Flexxaire Fan Push Solenoid
T997
OR
Winch Control +5v Power Out
F711
GN
CAN A Data Link (+)
Y925
YL
Counterbalance Sol 1
F712
GY
CAN A Data Link (-)
Y933
YL
Increment/Decrement Sw (N.O.) (Accugrade)
F714
PK
Right Turbo Inlet Press
Y934
WH
Increment/Decrement Sw (N.C.) (Accugrade)
Control Circuits
Lighting Circuits
Connector Number
Schematic
Location
Side View
Coordinate
Top View
Coordinate
CONN 1
B-13
G-17
G-40
CONN 2
B-13
G-17
G-31
CONN 3 Electric Winch CONN
A-13
F-12
F-33
CONN 4 Hydraulic Winch CONN
B-13
F-12
F-33
CONN 5
C-13
G-17
G-40
CONN 6
C-13
G-24
G-40
CONN 7
D-13
K-11
K-37
CONN 8
E-12
K-11
K-37
CONN 9
D-12
K-11
K-37
CONN 10
C-12
G-12
G-35
CONN 11
B-12
G-12
G-35
CONN 12
B-12
G-12
G-35
CONN 13
A-12
G-12
G-35
CONN 14
B-10, C-10
K-17
K-31
CONN 15
C-10
I-11
I-39
CONN 16
C-9
F-12
F-32
CONN 17
C-9
F-12
F-32
CONN 18
E-8
R-12
R-36
CONN 19
D-8
X-15
X-37
CONN 20
H-6
X-15
X-35
CONN 21
G-6
AA-7
AA-39
CONN 22
A-6
X-15
X-35
CONN 23
A-6
X-14
X-37
CONN 24
A-5
X-15
X-36
CONN 25
F-4
T-14
T-38
CONN 26
F-4
S-14
S-37
CONN 27
TDC Service Probe
C-4
U-13
U-37
CONN 28
I-2
Q-12
Q-37
CONN 29
H-2
BB-15
BB-33
CONN 30
G-2
BB-15
BB-38
Vol. 1 Connector Location
CONN 57
H-13
M-16
M-32
CONN 58
G-13
M-16
M-32
CONN 59
G-13
M-16
M-32
CONN 61
D-8
R-12
R-36
Related Electrical Service Manuals
Form Number
Alternator:
197-8820
SENR4130
Electric Starting Motor:
Consist:
207-1556
SENR3581
Consist:
237-1962
SENR3860
AccuGrade Laser System:
RENR8128
Caterpillar Monitoring System:
RENR2014
Engine Control:
SENR9345
Power Train Control:
RENR9867
Product Link Radio:
RENR7911
Title
Failure Mode Identifiers (FMI)¹
FMI No.
Failure Description
0
Data valid but above normal operational range.
1
Data valid but below normal operational range.
2
Data erratic, intermittent, or incorrect.
3
Voltage above normal or shorted high.
4
Voltage below normal or shorted low.
5
Current below normal or open circuit.
6
Current above normal or grounded circuit.
7
Mechanical system not responding properly.
8
Abnormal frequency, pulse width, or period.
9
Abnormal update.
10
Abnormal rate of change.
11
Failure mode not identifiable.
12
Bad device or component.
13
Out of calibration.
14
Parameter failures.
15
Parameter failures.
16
Parameter not available.
17
Module not responding.
18
Sensor supply fault.
19
Condition not met.
20
Parameter failures.
¹The FMI is a diagnostic code that indicates what type of failure has occurred.
Event Code
Condition
E096
High Fuel Pressure
E172
High Air Filter Restriction
E0194
High Exhast Temperature
E198
Low Fuel Pressure
E241
Abnormal Engine Fan System Operation
E360
Low Engine Oil Pressure
E361
High Engine Coolant Temperature
E362
Engine Overspeed
E539
High Intake Manifold Air Temperature
Event Codes For ADEM III ECM
Off Machine Switch Specification
Part No.
Function
Actuate
Deactuate
Contact Position
30±7 kPa
30±7 kPa
(39.9 to 253.8 psi)
(39.9 to 253.8 psi)
275 to 1750 kPa¹
-(39.9 to 253.8 psi)
-105-9152
Pre Lube Oil Pressure
Normally Closed
A/C Refrigerant Pressure
Normally Open²
¹ With increasing pressure the closed condition can be maintained up to 2800 kpa (405 psi), with decreasing pressure the closed
condition can be maintained down to 170 kpa (25psi).
² Contact position at the contacts of the harness connecto
r.
114-5333
Component Identifiers (CID¹)
Module Identifier (MID²)
Caterpillar Monitoring System
(MID No. 030)
CID
Component
0096
Fuel Level Sender
0100
Engine Oil Pressure Sensor
0110
Engine Coolant Temperature Sensor
0177
Transmission Oil Temperature Sensor
0248
Data Link
0263
Sensor Power Supply
0271
Action Alarm
0280
Transmission Oil Temperature Sender
0324
Action Lamp
0600
Hydraulic Oil Temperature Sensor
0819
Display Data Link
0821
Display Power Supply
1045
Power Train Oil Temperature Sensor
1425
Implement Tank Oil Temperature Sensor
Engine Control System
(MID No. 036)
CID
Component
0001
Injector Cylinder #1
0002
Injector Cylinder #2
0003
Injector Cylinder #3
0004
Injector Cylinder #4
0005
Injector Cylinder #5
0006
Injector Cylinder #6
0041
8 Volt DC Supply
0042
Injection Actuation Control Valve
0091
Throttle Position Signal
0094
Fuel Pressure
0100
Engine Oil Pressure
0110
Engine Coolant Temperature
0164
Injector Actuation Pressure
0168
Electrical System Voltage
0172
Intake Manifold Air Temperature
0190
Engine Speed Signal
0247
J1939 Data Link
0253
Personality Module
0261
Engine Timing Calibration
0262
5 Volt Sensor Supply
0264
Decel Throttle Position
0266
Incorrect Crank-Without-Inject Input
0268
Check Programable Parameters
0274
Atmospheric Pressure
0291
Engine Cooling Fan Solenoid
0296
Transmission ECM
0342
Secondary Engine Speed Sensor
1589
Turbo Inlet Air Pressure Sensor
1599
Engine Fan Pull Solenoid
1600
Engine Fan Push Solenoid
1639
Machine Security System
1785
Intake Manifold Pressure Sensor
Power Train Control System
(MID No. 113)
CID
Component
0070
Parking Brake Switch (On / Off Pole)
0168
Electrical System Voltage
0177
Transmission Oil Temperature Sensor
0262
5 Volt Sensor Power Supply
0298
Service Brake Switch
0299
Transmission Direction Lever Position Sensor
0368
Autoshift Switch
0444
Starter Motor Relay
0468
Service Brake Pedal Position Sensor
0490
Implement Lockout Switches
0497
Tilt Right Solenoid
0498
Tilt Left Solenoid
0585
Transmission Output Speed Sensor (1)
0588
Monitoring System Display
0590
Engine ECM
0621
Downshift Switch
0622
Upshift Switch
0650
Harness Code
0668
Transmission Shift Lever
0672
Torque Converter Output Speed Sensor
0673
Transmission Output Speed Sensor 2
0681
Parking Brake Solenoid
0689
Left Steering Brake Solenoid
0722
Secondary Brake Solenoid
0874
Mode Select Switch (Implement Handle)
0875
Manual Select Switch (Implement Handle)
0882
Hydraulic Lockout Solenoid
1078
Blade Control Handle Raise/Lower Position Sensor
1079
Blade Control Handle Tilt Position Sensor
1197
Blade Lower Solenoid
1198
Blade Raise Solenoid
1298
Implement Solenoids
1326
ECM Location Code
1401
Transmission Solenoid Valve 1
1402
Transmission Solenoid Valve 2
1403
Transmission Solenoid Valve 3
1404
Transmission Solenoid Valve 4
1405
Transmission Solenoid Valve 5
1450
Main Pump Hydraulic Pressure Sensor
1482
10 Volt Sensor Power Supply
1582
Transmission Lube Oil Temperature Sensor
1870
Blade Control Handle Thumb Rocker
1933
Blade Angle Left Solenoid
1934
Blade Angle Right Solenoid
1960
Ignition Key Reader
2114
Blade Control Handle Trigger Switch
2122
Reverse Switch
CID
Component
0168
Electrical System Voltage
0254
Eletronic Control Module
0269
Sensor Power Supply
1250
Remote Communication Module
1251
Alternator R Terminal
¹ The CID is a diagnostic code that indicates which component is faulty.
Product Link Radio
(MID No. 122)
² The MID is a diagnostic code that indicates which electronic control module
diagnosed the fault.
Resistor, Sender and Solenoid Specifications
Part No.
Component Description
Resistance (Ohms)¹
134-2540
Resistor:
CAN A
120
106-5122
Solenoid:
A/C Clutch
17.6 ± 0.6
Hydraulic Oil Temperature
-40 °C = 33,650
T/C Oil Temperature
0 °C = 3,268
145-7028
Sender:
Xmsn Lube Temperature
50 °C = 360
Xmsn Sump Temperature
100 °C = 68
150 °C = 18.6
263-5729
Sender:
Fuel Level
Empty = 92 - 98
Full = 0 - 3.5
201-0950
Solenoid:
Implement Lockout
41.9 ± 2.1
285-5730
Solenoids:
PAT Left/Right Angle
5 ± 0.3
220-4324
Solenoids:
Xmsn Clutch
8.7 ± 0.4
239-1134
Solenoid:
Start Aid
20
3E-9205
Solenoid:
Flexxaire Fan
24.9 ± 0.4
¹ At room temperature unless otherwise noted.
