API Select Collection
API API 1130 Computational Pipeline Monitoring for Liquid Pipelines-Second Edition
API API 510
Pressure Vessel Inspection Code: Maintenance Inspection, Rating, Repair, and Alteration-Eighth Edition; Addendum 1 December 1998; Addendum 2
December 2000; Addendum 3 December 2001; Addendum 4 August 2003
API API 570
Piping Inspection Code Inspection, Repair, Alteration, and Rerating of In-Service Piping Systems-Second Edition; Addendum 1 - February 2000; Addendum 2 - December 2001; Addendum 3 - August 2003
API API/IP
SPEC 1582 Specification for Similarity for API/IP 1581 Aviation Jet Fuel Filter/Separators API BULL 2U Bulletin on Stability Design of Cylindrical Shells-Third Edition
API BULL 2V Design of Flat Plate Structures-Third Edition
API BULL 5C2 Bulletin on Performance Properties of Casing, Tubing, and Drill Pipe-
Twenty-First Edition
API BULL 5C3 Bulletin on Formulas and Calculations for Casing, Tubing, Drill Pipe, and Line
Pipe Properties-Sixth Edition; Supplement 1 - April 1999
API BULL D16 Suggested Procedure for Development of Spill Prevention Control and
Countermeasure Plans-Third Edition
API BULL D16 TEMPLATE
Suggested Procedure for Development of Spill Prevention Control and Countermeasure Plans - Plan Template-Fourth Edition
API MPMS 1 Manual of Petroleum Measurement Standards Chapter 1 - Vocabulary
API MPMS 10.4
Manual of Petroleum Measurement Standards Chapter 10 - Sediment and Water Section 4 - Determination of Water and/or Sediment in Crude Oil by the Centrifuge Method (Field Procedure)
API MPMS 11.2
Manual of Petroleum Measurement Standards Chapter 11.2.1 and 11.2.1M - Compressibility Factors for Hydrocarbons: 0-90 Degrees API Gravity and 638-1074 Kilograms per Cubic Metre Ranges Chapter 11.2.3 and 11.2.3M - Water Calibration of Provers Computer Tape
API MPMS 11.4.1
Measurement Standards Chapter 11Physical Properties Data Section 4Properties of Reference Materials Part 1Density of Water and Water
Volumetric Correction Factors for Water Calibration of Volumetric Provers-First Edition
API MPMS 12.1.1
Manual of Petroleum Measurement Standards Chapter 12 - Calculation of Petroleum Quantities Section 1 - Calculation of Static Petroleum Quantities Part 1 - Upright Cylindrical Tanks and Marine Vessels-Second Edition
API MPMS 12.1.2
Manual of Petroleum Measurement Standards Chapter 12 - Calculation of Petroleum Quantities Section 1 - Calculation of Static Petroleum Quantities Part 2 - Calculation Procedures for Tank Cars-First Edition
API MPMS 12.2
Manual of Petroleum Measurement Standards Chapter 12 - Calculation of Petroleum Quantities Section 2 - Calculation of Liquid Petroleum Quantities Measured by Turbine or Displacement Meters-First Edition
12.2.1 Petroleum Quantities Section 2 - Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors Part 1 - Introduction- Second Edition
API MPMS 12.2.2
Manual of Petroleum Measurement Standards Chapter 12 - Calculation of Petroleum Quantities Section 2 - Calculation of Petroleum Quantities Using Dynamic Measurement Methods and Volumetric Correction Factors Part 2 - Measurement Tickets-Third Edition
API MPMS 14.3.1
Manual of Petroleum Measurement Standards Chapter 14 - Natural Gas Fluids Measurement Section 3 - Concentric, Square-Edged Orifice Meters Part 1 - General Equations and Uncertainty Guidelines-Third Edition; Errata - 1991; Errata - 1993; Replaces API MPMS
API MPMS 14.3.3
Manual of Petroleum Measurement Standards Chapter 14 - Natural Gas Fluids Measurement Section 3 - Concentric, Square-Edged Orifice Meters Part 3 - Natural Gas Applications
API MPMS 14.4
Manual of Petroleum Measurement Standards Chapter 14 - Natural Gas Fluids Measurement Section 4 - Converting Mass of Natural Gas Liquids and Vapors to Equivalent Liquid Volumes-First Edition
API MPMS 14.5
Calculation of Gross Heating Value, Relative Density and Compressibility Factor for Natural Gas Mixtures from Compositional Analysis-GPA STD 2172- 96
API MPMS 14.8
Manual of Petroleum Measurement Standards Chapter 14 - Natural Gas Fluids Measurement Section 8 - Liquefied Petroleum Gas Measurement-Second Edition
API MPMS 15
Manual of Petroleum Measurement Standards Chapter 15 - Guidelines for the Use of the International System of Units (SI) in the Petroleum and Allied Industries-API PUBL 2564
API MPMS 16.2
Manual of Petroleum Measurement Standards Chapter 16 - Measurement of Hydrocarbon Fluids by Weight or Mass Section 2 - Mass Measurement of Liquid Hydrocarbons in Vertical Cylindrical Storage Tanks by Hydrostatic Tank Gauging-First Edition
API MPMS 2.2A
Manual of Petroleum Measurement Standard Chapter 2 - Tank Calibration Section 2A - Measurement and Calibration of Upright Cylindrical Tanks by the Manual Tank Strapping Method-First Edition
API MPMS 2.2B
Manual of Petroleum Measurement Standards Chapter 2 - Tank Calibration Section 2B - Calibration of Upright Cylindrical Tanks Using the Optical Reference Line Method-First Edition
API MPMS 2.2C
Manual of Petroleum Measurement Standards Chapter 2 - Tank Calibration Section 2C - Calibration of Upright Cylindrical Tanks Using the Optical- Triangulation Method-First Edition/ ISO 7507-3 Adoption
API MPMS 2.8A
Manual of Petroleum Measurement Standards Chapter 2 - Tank Calibration Section 8A - Calibration of Tanks on Ships and Oceangoing Barges-First Edition
API MPMS 20.1
Manual of Petroleum Measurement Standards Chapter 20 - Allocation Measurement Section 1 - Allocation Measurement
21.1 Using Electronic Metering Systems Section 1 - Electronic Gas Measurement
API MPMS 3.1A
Manual of Petroleum Measurement Standards Chapter 3 - Tank Gauging Section 1A - Standard Practice for the Manual Gauging of Petroleum and Petroleum Products-Second Edition
API MPMS 3.1B
Manual of Petroleum Measurement Standards Chapter 3 - Tank Gauging Section 1B - Standard Practice for Level Measurement of Liquid Hydrocarbons in Stationary Tanks by Automatic Tank Gauging-Second Edition
API MPMS 4.1 Manual of Petroleum Measurement Standards Chapter 4 - Proving Systems
Section 1 - Introduction-Third Edition
API MPMS 4.2 Manual of Petroleum Measurement Standards Chapter 4 - Proving Systems
Section 2 - Displacement Provers-Third Edition
API MPMS 4.4 Manual of Petroleum Measurement Standards Chapter 4 - Proving Systems
Section 4 - Tank Provers-Second Edition
API MPMS 4.5
Manual of Petroleum Measurement Standards Chapter 4 - Proving Systems Section 5 - Master-Meter Provers-Second Edition; Supersedes 1101, 2531, 2533, 2534
API MPMS 4.8 Manual of Petroleum Measurement Standards Chapter 4 - Proving Systems
Section 8 - Operation of Proving Systems
API MPMS 5.1 Manual of Petroleum Measurement Standards Chapter 5 - Metering Section 1 -
General Considerations for Measurement by Meters-Fourth Edition
API MPMS 5.2 Manual of Petroleum Measurement Standards Chapter 5 - Metering Section 2 -
Measurement of Liquid Hydrocarbons by Displacement Meters-Third Edition
API MPMS 5.6 Metering, Section 6 - Measurement of Liquid Hydrocarbons by Coriolis
Meters-First Edition; Replaces API H00004 and API H00006
API MPMS 5.8
Manual of Petroleum Measurement Standards Chapter 5 - Metering - Section 8 - Measurement of Liquid Hydrocarbons by Ultrasonic Flow Meters Using Transit Time Technology-First Edition
API MPMS 6.1 Manual of Petroleum Measurement Standards Chapter 6 - Metering Assemblies
Section 1 - Lease Automatic Custody Transfer (LACT) Systems-Second Edition
API MPMS 7 Manual of Petroleum Measurement Standards Chapter 7 - Temperature
Determination-First Edition; Supersedes Chapter 7, Section 1, 2, 3 and 4
API MPMS 8.2
Manual of Petroleum Measurement Standards Chapter 8 - Sampling Section 2 - Standard Practice for Automatic Sampling of Liquid Petroleum and Petroleum Products-Second Edition; ASTM D4177
API MPMS 8.4
Manual of Petroleum Measurement Standards Chapter 8 - Sampling Section 4 - Standard Practice for Sampling and Handling of Fuels for Volatility
Measurement- Second Edition
API MPMS 9.2
Manual of Petroleum Measurement Standards Chapter 9 - Determination Section 2 - Standard Test Method for Density or Relative Density of Light Hydrocarbons by Pressure Hydrometer-Second Edition
API MPMS 9.3
Manual of Petroleum Measurement Standards Chapter 9 - Density
Determination Section 3 - Standard Test Method for Density, Relative Density, and API Gravity of Crude Petroleum and Liquid Petroleum Products by
API PUBL 1155
Evaluation Methodology for Software Based Leak Detection Systems- First Edition
API PUBL 2026
Safe Access/Egress Involving Floating Roofs of Storage Tanks in Petroleum Service-Second Edition
API PUBL 2030
Application of Water Spray Systems for Fire Protection in the Petroleum Industry-Second Edition
API PUBL
2207 Preparing Tank Bottoms for Hot Work-Fifth Edition; Errata June 1999 API PUBL
2218
Fireproofing Practices in Petroleum and Petrochemical Processing Plants-Second Edition
API PUBL 2510A
Fire-Protection Considerations for the Design and Operation of Liquefied Petroleum Gas (LPG) Storage Facilities-Second Edition
API PUBL 327 Aboveground Storage Tank Standards: A Tutorial
API PUBL
4686 1999 Oil Spill Conference Proceedings API PUBL
4723 Refinery Stream Speciation
API PUBL 534 Heat Recovery Steam Generators First Edition-First Edition
API PUBL 581 Risk-Based Inspection Base Resource Document-First Edition
API PUBL 850 API Standards 620, 650, and 653 Interpretations - Tank Construction and
In-Service Inspection-Answers to Technical Inquiries; First Edition
API PUBL 938 Experimental Study of Causes and Repair of Cracking of 1 1/4Cr- 1/2Mo Steel
Equipment
API PUBL 939- B
Repair and Remediation Strategies for Equipment Operating in Wet H2S Service
API REPORT 3 Oil Analysis in Production Discharges
API RP 1102 Steel Pipelines Crossing Railroads and Highways
API RP 1110 Pressure Testing of Liquid Petroleum Pipelines-Fourth Edition
API RP 1111 Design, Construction, Operation, and Maintenance of Offshore Hydrocarbon
Pipelines (Limit State Design)-Third Edition
API RP 1117 Movement of In-Service Pipelines
API RP 11AR Recommended Practice for Care and Use of Subsurface Pumps- Fourth Edition
API RP 11BR Recommended Practice for Care and Handling of Sucker Rods- Eighth Edition;
Supplement 1 10-1-1990; Supplement 2 7-1-1991
API RP 11PGT Recommended Practice for Packaged Combustion Gas Turbines
API RP 11S2 Recommended Practice for Electric Submersible Pump Testing- Second
Edition; Effective Date: 10/01/1997
API RP 11S2 RUSSIAN
Recommended Practice for Electric Submersible Pump Testing- Second Edition; Effective Date: 10/01/1997
API RP 11S3 Recommended Practice for Electric Submersible Pump Installations- Second
API RP 11S4 Recommended Practice for Sizing and Selection of Electric Submersible Pump
Installations-Third Edition
API RP 12N Recommended Practice for the Operation, Maintenance and Testing of Firebox
Flame Arrestors
API RP 12R1 Recommended Practice for Setting, Maintenance, Inspection, Operation and
Repair of Tanks in Production Service-Fifth Edition; Effective Date: 10/01/1997
API RP 13C Recommended Practice for Drilling Fluid Processing Systems Evaluation-Third
Edition; Replaces API RP 13E; Errata: 04/2005
API RP 13D Recommended Practice on the Rheology and Hydraulics of Oil-Well Drilling
Fluids-Fourth Edition
API RP 14B Petroleum and natural gas industries Subsurface safety valve systems Design,
installation, operation and redress-Fifth Edition; ISO 10417
API RP 14C Recommended Practice for Analysis, Design, Installation, and Testing of Basic
Surface Safety Systems for Offshore Production Platforms-Seventh Edition
API RP 14E Recommended Practice for Design and Installation of Offshore Production
Platform Piping Systems
API RP 14F
Recommended Practice for Design and Installation of Electrical Systems for Fixed and Floating Offshore Petroleum Facilities for Unclassified and Class I, Division 1 and Division 2 Locations-Fourth Edition
API RP 14FZ
Recommended Practice for Design and Installation of Electrical Systems for Fixed and Floating Offshore Petroleum Facilities for Unclassified and Class I, Zone 0, Zone 1 and Zone 2 Locations-First Edition
API RP 14G Recommended Practice for Fire Prevention and Control on Open Type Offshore
Production Platforms
API RP 14H
Recommended Practice for Installation, Maintenance and Repair of Surface Safety Valves and Underwater Safety Valves Offshore-Fourth Edition; ISO 10419; Errata - 1996
API RP 14J Recommended Practice for Design and Hazards Analysis for Offshore
Production Facilities-Second Edition
API RP 1615 Installation of Underground Petroleum Storage Systems
API RP 1632 Cathodic Protection of Underground Petroleum Storage Tanks and Piping
Systems
API RP 16Q Recommended Practice for Design, Selection, Operation and Maintenance of
Marine Drilling Riser Systems-First Edition; Formerly RP 2Q and RP 2K
API RP 17A
Design and Operation of Subsea Production Systems - General Requirements and Recommendations-Fourth Edition; ISO 13628-1:2005; ISO 13628-1
Adoption
API RP 17B Recommended Practice for Flexible Pipe-Third Edition
API RP 17C Recommended Practice on TFL (Through Flowline) Systems-Second Edition;
ISO 13628-3/ISO 13628-3 Adoption
API RP 2001 Fire Protection in Refineries-Eighth Edition
API RP 2003 Protection Against Ignitions Arising out of Static, Lightning, and Stray
API RP 2009 Safe Welding, Cutting, and Other Hot Work Practices in the Petroleum and
Petrochemical Industries
API RP 2016 Guidelines and Procedures for Entering and Cleaning Petroleum Storage
Tanks-First Edition
API RP 2021 Management of Atmospheric Storage Tank Fires-Fourth Edition
API RP 2028 Flame Arresters in Piping Systems
API RP 2200 Repairing Crude Oil, Liquefied Petroleum Gas, and Product Pipelines
API RP 2201 Safe Hot Tapping Practices in the Petroleum & Petrochemical Industries-Fifth
Edition
API RP 2210 Flame Arresters for Vents of Tanks Storing Petroleum Products-Third Edition
API RP 2221 Contractor and Owner Safety Program Implementation-Second Edition
API RP 2350 Overfill Protection for Storage Tanks in Petroleum Facilities-Third Edition
API RP 2556 Correcting Gauge Tables for Incrustation
API RP 2A- LRFD
Recommended Practice for Planning, Designing and Constructing Fixed
Offshore Platforms - Load and Resistance Factor Design-First Edition; Errata - October 1993; Supplement 1 - February 1997
API RP 2A- WSD
Recommended Practice for Planning, Designing and Constructing Fixed Offshore Platforms - Working Stress Design-Twenty-First Edition; Errata and Supplement 2: 10/2005
API RP 2D Operation and Maintenance of Offshore Cranes-Fifth Edition
API RP 2FPS Recommended Practice for Planning, Designing, and Construction Floating
Production Systems-First Edition
API RP 2I In-Service Inspection of Mooring Hardware for Floating Drilling Units- Second
Edition
API RP 2L Recommended Practice for Planning, Designing, and Constructing Heliports for
Fixed Offshore Platforms
API RP 2N Recommended Practice for Planning, Designing, and Constructing Structures
and Pipelines for Arctic Conditions
API RP 2RD Design of Risers for Floating Production Systems (FPSs) and Tension-Leg
Platforms (TLPs)-First Edition
API RP 2SK Design and Analysis of Station keeping Systems for Floating Structures-Third
Edition
API RP 2T Recommended Practice for Planning, Designing, and Constructing Tension Leg
Platforms-Second Edition
API RP 2X
Recommended Practice for Ultrasonic and Magnetic Examination of Offshore Structural Fabrication and Guidelines for Qualification of Technicians-Fourth Edition
API RP 2Z Recommended Practice for Preproduction Qualification for Steel Plates for
Offshore Structures-Fourth Edition
API RP 44 Sampling Petroleum Reservoir Fluids-Second Edition
API RP 45 Recommended Practice for Analysis of Oilfield Waters-Third Edition
at Petroleum Facilities Classified as Class I, Division 1 and Division 2-First Edition; Errata 10/17/1998
API RP 505
Recommended Practice for Classification of Locations for Electrical Installations at Petroleum Facilities Classified as Class I, Zone 0, Zone 1, and Zone 2-First Edition; Errata 8/17/98
API RP 520 PT I
Sizing, Selection, and Installation of Pressure-Relieving Devices in Refineries; Part I - Sizing and Selection-Seventh Edition
API RP 520 PT II
Sizing, Selection, and Installation of Pressure-Relieving Devices in Refineries Part II - Installation-Fifth Edition
API RP 521 Guide for Pressure-Relieving and Depressuring Systems-Fourth Edition; Errata
February 15, 1999
API RP 54 Recommended Practice for Occupational Safety for Oil and Gas Well Drilling
and Servicing Operations-Third Edition
API RP 540 Electrical Installations in Petroleum Processing Plants-Fourth Edition
API RP 55 Recommended Practices for Oil and Gas Producing and Gas Processing Plant
Operations Involving Hydrogen Sulfide-Second Edition
API RP 551 Process Measurement Instrumentation
API RP 552 Transmission Systems-First Edition
API RP 553 Refinery Control Valves-First Edition
API RP 554 Process Instrumentation and Control-First Edition
API RP 555 Process Analyzers-Second Edition
API RP 556 Instrumentation and Control Systems for Fired Heaters and Steam
Generators-First Edition
API RP 557 Guide to Advanced Control Systems-First Edition
API RP 571 Damage Mechanisms Affecting Fixed Equipment in the Refining Industry-First
Edition
API RP 572 Inspection of Pressure Vessels (Towers, Drums, Reactors, Heat Exchangers,
and Condensers)-Second Edition
API RP 573 Inspection of Fired Boilers and Heaters-Second Edition
API RP 574 Inspection Practices for Piping System Components-Second Edition
API RP 575 Guidelines and Methods for Inspection of Existing Atmospheric and
Low-Pressure Storage Tanks-Second Edition
API RP 576 Inspection of Pressure-Relieving Devices-Second Edition
API RP 577 Welding Inspection and Metallurgy-First Edition
API RP 578 Material Verification Program for New and Existing Alloy Piping Systems-First
Edition
API RP 579 Fitness-for-Service-First Edition; Errata March 2000
API RP 580 Risk-Based Inspection-First Edition
API RP 582 Welding Guidelines for the Chemical, Oil, and Gas Industries-First Edition
API RP 591 Process Valve Qualification Procedure-Third Edition
Pipe-Second Edition/ISO 13678 Adoption
API RP 5A5 Field Inspection of New Casing, Tubing, and Plain-End Drill Pipe- Seventh
Edition; ISO 15463 Adoption
API RP 5B1 Gauging and Inspection of Casing, Tubing, and Line Pipe Threads-Fifth Edition;
Addendum 1: 09/2004
API RP 5C1 Recommended Practice for Care and Use of Casing and Tubing- Eighteenth
Edition
API RP 5C5 Recommended Practice on Procedures for Testing Casing and Tubing
Connections-Third Edition/ISO 13679 Adoption
API RP 5UE Recommended Practice for Ultrasonic Evaluation of Pipe Imperfections-Second
Edition
API RP 64 Recommended Practices for Diverter Systems Equipment and
Operations-Second Edition
API RP 651 Cathodic Protection of Aboveground Petroleum Storage Tanks-Second Edition
API RP 652 Linings of Aboveground Petroleum Storage Tank Bottoms-Third Edition
API RP 683 Quality Improvement Manual for Mechanical Equipment in Petroleum,
Chemical, and Gas Industries
API RP 684 Paragraphs Rotodynamic Tutorial: Lateral Critical Speeds, Unbalance
Response, Stability, Train Torsionals and Rotor Balancing-Second Edition
API RP 686 Recommended Practices for Machinery Installation and Installation Design-First
Edition
API RP 687 Rotor Repair-First Edition
API RP 6HT Heat Treatment and Testing of Large Cross Section and Critical Section
Components-First Edition
API RP 75 Recommended Practices for Development of a Safety and Environmental
Management Program for Offshore Operations and Facilities-Third Edition
API RP 751 Safe Operation of Hydrofluoric Acid Alkylation Units-Second Edition
API RP 752 Management of Hazards Associated with Location of Process Plant
Buildings-Second Edition
API RP 7C- 11F
Recommended Practice for Installation, Maintenance, and Operation of Internal-Combustion Engines
API RP 7G Recommended Practice for Drill Stem Design and Operating Limits- Sixteenth
Edition; Errata May 2000; Addendum 1: November 2003
API RP 80 Guidelines for the Definition of Onshore Gas Gathering Lines-First Edition
API RP 932- B
Design, Materials, Fabrication, Operation, and Inspection Guidelines for Corrosion Control in Hydroprocessing Reactor Effluent Air Cooler (REAC) Systems-First Edition
API RP 934
Materials and Fabrication Requirements for 2-1/4Cr-1Mo and 3Cr-1Mo Steel Heavy Wall Pressure Vessels for High Temperature, High Pressure Hyrdogen Service- First Edition
API RP 936 Refractory Installation Quality Control Guidelines-Inspection and Testing
API RP 941 Steels for Hydrogen Service at Elevated Temperatures and Pressures in
Petroleum Refineries and Petrochemical Plants-Sixth Edition
API RP 945 Avoiding Environmental Cracking in Amine Units-Third Edition
API RP 9B Recommended Practice on Application Care, and Use of Wire Rope for Oil
Field Service-Twelfth Edition
API SPEC 10A
Specification for Cements and Materials for Well Cementing-Twenty- Third Edition; ANSI/API 10A/ISO 10426-1-2001/ISO 10426-1 Adoption; Errata: January 2005
API SPEC 11D1
Petroleum and Natural Gas Industries - Downhole Equipment - Packers and Bridge Plugs-First Edition; ISO 14310:2001/ ISO 14310 Adoption
API SPEC 11E Specification for Pumping Units
API SPEC 12B Specification for Bolted Tanks for Storage of Production Liquids
API SPEC 12D Specification for Field Welded Tanks for Storage of Production Liquids
API SPEC 12F Specification for Shop Welded Tanks for Storage of Production Liquids
API SPEC 12J Specification for Oil and Gas Separators
API SPEC 12P Specification for Fiberglass Reinforced Plastic Tanks
API SPEC 14A Petroleum and natural gas industries Downhole equipment Subsurface safety
valve equipment-Eleventh Edition; ISO 10432 Adoption
API SPEC 16A Specification for Drill-Through Equipment-Third Edition; ISO 13533:2001/ISO
13533 Adoption; Errata: 11/2004
API SPEC 16D Specification for Control Systems for Drilling Well Control Equipment and
Control Systems for Diverter Equipment-Second Edition
API SPEC 16F Specification for Marine Drilling Riser Equipment-First Edition
API SPEC
16RCD Specification for Drill Through Equipment Rotating Control Devices-First Edition API SPEC 17E Specification for Subsea Umbilicals-Third Edition/ ISO 13628-5 Adoption
API SPEC 17F Specification for Subsea Production Control Systems-First Edition; ISO
13628-6:2000/ISO 13628-6 Adoption
API SPEC 17J Specification for Unbonded Flexible Pipe-Second Edition; Errata 5/25/2001;
Addendum 1 06/2002
API SPEC 2B Specification for the Fabrication of Structural Steel Pipe-Sixth Edition
API SPEC 2C Specification for Offshore Pedestal Mounted Cranes-Sixth Edition
API SPEC 2H Specification for Carbon Manganese Steel Plate for Offshore Platform Tubular
Joints-Eighth Edition; Effective Date: February 1, 2000
API SPEC 4F Specification for Drilling and Well Servicing Structures
API SPEC 5B
Specification for Threading, Gauging, and Thread Inspection of Casing, Tubing, and Line Pipe Threads (U.S. Customary Units)-Fourteenth Edition; Errata
4/9/1998; Addendum 1 3/2004
API SPEC 5CT Specification for Casing and Tubing-Eighth Edition; ISO 11960:2004 Adoption;
Effective Date: January 1, 2006
API SPEC 5L Specification for Line Pipe-Forty-Third Edition; Errata: 12/20/2004
API SPEC 5LC Specification for CRA Line Pipe-Third Edition
API SPEC 5LD Specification for CRA Clad or Lined Steel Pipe-Second Edition
API SPEC 6A Specification for Wellhead and Christmas Tree Equipment-Nineteenth Edition;
ISO 10423 Adoption; Errata 1: 9/01/2004; Errata 2: 04/25/2005
API SPEC 6A718
Specification of Nickel Base Alloy 718 (UNS N07718) for Oil and Gas Drilling and Production Equipment-First Edition
API SPEC 6D
ISO 14313:1999, Petroleum and Natural Gas Industries-Pipeline Transportation Systems-Pipeline Valves-Twenty-Second Edition/ISO 14313 Adoption; Errata: 3/01/2005
API SPEC 6FA Specification for Fire Test for Valves-Third Edition
API SPEC 8C
Specification for Drilling and Production Hoisting Equipment (PSL 1 and PSL 2)-Fourth Edition; ISO 13535:2000/ ISO 13535 Adoption; Addendum 1: 11/1/2004; Addendum 2: 04/15/2005;
API SPEC 9A Specification for Wire Rope-Twenty-fifth Edition; ANSI/API SPEC 9A/ISO
10425:2003/ISO 10425 Adoption
API SPEC Q1
Specification for Quality Programs for the Petroleum, Petrochemical and Natural Gas Industry-Seventh Edition; Errata: August 2003/ISO TS29001 Adoption
API STD 1104 Welding of Pipelines and Related Facilities-Twentieth Edition
API STD 1160 Managing System Integrity for Hazardous Liquid Pipelines-First Edition
API STD 1164 Pipeline SCADA Security-First Edition
API STD 1631 Interior Lining and Periodic Inspection of Underground Storage Tanks- Fifth
Edition; Supersedes RP 1631-1997
API STD 2000 Venting Atmospheric and Low-Pressure Storage Tanks Non-refrigerated and
Refrigerated-Fifth Edition; Errata 11/15/1999
API STD 2015 Requirements for Safe Entry and Cleaning of Petroleum Storage Tanks-Sixth
Edition
API STD 2217A
Guidelines for Safe Work in Inert Confined Spaces in the Petroleum and Petrochemical Industries-Third Edition
API STD 2220 Contractor Safety Performance Process-Second Edition
API STD 2510 Design and Construction of LPG Installations-Eighth Edition
API STD 2610 Design, Construction, Operation, Maintenance, and Inspection of Terminal &
Tank Facilities-Second Edition
API STD 526 Flanged Steel Pressure Relief Valves-Fifth Edition
API STD 527 Seat Tightness of Pressure Relief Valves
API STD 530 Calculation of Heater-Tube Thickness in Petroleum Refineries-Fifth Edition; ISO
13704:2001/ISO 13704 Adoption; Errata 1:3/01/04
API STD 537 Flare Details for General Refinery and Petrochemical Service-First Edition
API STD 541 Form-Wound Squirrel-Cage Induction Motors - 500 Horsepower and
API STD 546 Brushless Synchronous Machines - 500 kVA and Larger-Second Edition
API STD 547 General-purpose Form-wound Squirrel Cage Induction Motors 250 Horsepower
and Larger-First Edition
API STD 560 Fired Heaters for General Refinery Services-Third Edition; Errata: January 2002
API STD 594 Check Valves: Flanged, Lug, Wafer and Butt-welding-Sixth Edition
API STD 598 Valve Inspection and Testing-Eighth Edition
API STD 599 Metal Plug Valves - Flanged, Threaded and Welding Ends-Fifth Edition
API STD 5T1 Standard on Imperfection Terminology-Tenth Edition; Formerly Bull 5T1;
Addendum 1: 9/2003
API STD 600 Bolted Bonnet Steel Gate Valves for Petroleum and Natural Gas
Industries-Eleventh Edition; ISO 10434:1998/ ISO 10434 Adoption
API STD 602 Steel Gate, Globe and Check Valves for Sizes DN 100 and Smaller for the
Petroleum and Natural Gas Industries-Eighth Edition; ISO 15761 Adoption
API STD 603 Corrosion-Resistant, Bolted Bonnet Gate Valves - Flanged and Butt- Welding
Ends-Sixth Edition
API STD 607 Fire Test for Soft-Seated Quarter-Turn Valves-Fifth Edition; ISO 10497- 5:2004
Adoption
API STD 608 Metal Ball Valves - Flanged, Threaded, and Welding End-Third Edition
API STD 609 Butterfly Valves: Double Flanged, Lug- and Wafer-Type-Sixth Edition
API STD 610 Centrifugal Pumps for Petroleum, Petrochemical and Natural Gas
Industries-Tenth Edition; ISO 13709 Adoption
API STD 611 General-Purpose Steam Turbines for Petroleum, Chemical, and Gas Industry
Services-Fourth Edition
API STD 612 Petroleum, Petrochemical and Natural Gas Industries - Steam Turbines -
Special-Purpose Applications-Sixth Edition
API STD 613 Special Purpose Gear Units for Petroleum, Chemical, and Gas Industry
Services-Fifth Edition
API STD 614 Lubrication, Shaft-Sealing, and Control-Oil Systems and Auxiliaries for
Petroleum, Chemical and Gas Industry Services-Fourth Edition
API STD 616 Gas Turbines for Petroleum, Chemical, and Gas Industry Services- Fourth
Edition
API STD 617 Axial and Centrifugal Compressors and Expander-Compressors for Petroleum,
Chemical and Gas Industry Services-Seventh Edition; Errata: June 1, 2003
API STD 618 Reciprocating Compressors for Petroleum, Chemical, and Gas Industry
Services
API STD 619 Rotary-Type Positive-Displacement Compressors for Petroleum, Petrochemical,
and Natural Gas Industries-Fourth Edition
API STD 620 Design and Construction of Large, Welded, Low-Pressure Storage Tanks-Tenth
Edition; Addendum 1: June 2004
API STD 650 Welded Steel Tanks for Oil Storage-Tenth Edition; Addendum 1, January 2000;
Addendum 2, November 2001; Addendum 3, September 2003
Addendum 1: 9/2003; Addendum 2: 11/2005
API STD 660 Shell-and-Tube Heat Exchangers for General Refinery Services- Seventh
Edition/ ISO 16812 Adoption
API STD 661 Air-Cooled Heat Exchangers for General Refinery Service-Fifth Edition; ISO
13706: 2000/ISO 13706 Adoption
API STD 662 Plate Heat Exchangers for General Refinery Services-Second Edition; ISO
15547: 2000/ISO 15547 Adoption
API STD 670 Machinery Protection Systems-Fourth Edition
API STD 671 Special-Purpose Couplings for Petroleum, Chemical, and Gas Industry
Services-Third Edition
API STD 672 Packaged, Integrally Geared Centrifugal Air Compressors for Petroleum,
Chemical, and Gas Industry Services-Fourth Edition
API STD 673 Centrifugal Fans for Petroleum, Chemical and Gas for Industry
Services-Second Edition; Errata: 10/2002
API STD 674 Positive Displacement Pumps - Reciprocating
API STD 675 Positive Displacement Pumps - Controlled Volume
API STD 676 Positive Displacement Pumps - Rotary-Errata; 06/15/1999
API STD 677 General Purpose Gear Units for Petroleum, Chemical, and Gas Industry
Services-Second Edition
API STD 681 Liquid Ring Vacuum Pumps and Compressors for Petroleum, Chemical, and
Gas Industry Services-First Edition
API STD 682 Pumps Shaft Sealing Systems for Centrifugal and Rotary Pumps-Third Edition;
ISO 21049 Adoption
API STD 685 Sealless Centrifugal Pumps for Petroleum, Heavy Duty Chemical, and Gas
Industry Services Downstream Segment
API TR 17TR1 Evaluation Standard for Internal Pressure Sheath Polymers for High
Temperature Flexible Pipes-First Edition
API TR 17TR2 The Ageing of PA-11 in Flexible Pipes-First Edition
API TR 17TR3 An Evaluation of the Risks and Benefits of Penetrations in Subsea Wellheads
below the BOP Stack
API TR 2567 Evaporative Loss from Storage Tank Floating Roof Landings
API TR 6AF Technical Report on Capabilities of API Flanges under Combinations of
Load-Second Edition
API TR 6AF2 Technical Report on Capabilities of API Integral Flanges under Combination of
Loading - Phase II-Second Edition
