Single Output Switching Power Supply

(1)

SPECIFICATION

MODEL RS-15-12 DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER

OUTPUT VOLTAGE ADJ. RANGE

LINE REGULATIONNote.4 LOAD REGULATION Note.5 SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE EFFICIENCY (Typ.) AC CURRENT (Typ.) INPUT

INRUSH CURRENT (Typ.) LEAKAGE CURRENT SAFETY STANDARDS HARMONIC CURRENT EMS IMMUNITY WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. TEMP. COEFFICIENT VIBRATION MTBF DIMENSION OTHERS NOTE PACKING OVERLOAD OVER VOLTAGE 12V 1.3A 0 ~ 1.3A 15.6W 120mVp-p 10.8 ~ 13.2V ±1.0% ±0.5% ±0.5% 1000ms, 30ms/230VAC 70ms/230VAC 85 ~ 264VAC 47 ~ 63Hz 13.8 ~ 16.2V 81%

COLD START 65A / 230VAC <2mA / 240VAC

Above 105% rated output power

Compliance to EN55022 (CISPR22) Class B Compliance to EN61000-3-2,-3

Compliance to EN61000-4-2, 3, 4, 5, 6, 8,11, ENV50204, EN55024, EN61000-6-1 , criteria A -20 ~ +70°C (Refer to output load derating curve)

20 ~ 90% RH non-condensing -40 ~ +85°C

±0.03%/°C (0 ~ 50°C)

10 ~ 500Hz, 5G 10min./1cycle, period for 60min. each along X, Y, Z axes

1608.8Khrs min. MIL-HDBK-217F (25! ) 62.5*51*28mm (L*W*H)

0.13Kg; 108pcs/15Kg/0.71CUFT

Single Output Switching Power Supply

R S - 1 5

WITHSTAND VOLTAGE ISOLATION RESISTANCE

I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC 25°C 70%RH ENVIRONMENT

EMC (Note 6) PROTECTION

EMI CONDUCTION & RADIATION

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. RIPPLE & NOISE (max.)Note.2

VOLTAGE TOLERANCENote.3

•

Universal AC input / Full range

Protections: Short circuit / Overload / Over voltage / Over temperature Cooling by free air convection

LED indicator for power on 100% full load burn-in test All using 105°C

Withstand 300VAC surge input for 5 second High operating temperature up to 70°C Withstand 5G vibration test

High efficiency, long life and high reliability

long life electrolytic capacitors

Features :

Protection type : Hiccup mode, recovers automatically after fault condition is removed

Protection type : Shut off o/p voltage, clamping by zener diode 0.25A/230VAC

UL60950-1, TUV EN60950-1 approved OVER TEMPERATURE

U1 Tj 140°C typically (U1) detect on main control IC

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down

..

•

SAFETY &

(2)

Mechanical Specification

AMBIENT TEMPERATURE (°C) O A % ) L D ( -10 30 40 20 40 80 60 100 60 50 70

Case No.971A Unit:mm

Block Diagram

CIRCUIT DETECTION EMI FILTER RECTIFIERS & FILTER POWER SWITCHING FILTER & RECTIFIERS _+V -V I/P FG CONTROL PWM fosc : 132KHz Terminal Pin No. Assignment

Pin No. 1 2 4 3 5 Assignment DC OUTPUT -V DC OUTPUT +V FG AC/L AC/N

Output Derating VS Input Voltage

INPUT VOLTAGE (VAC) 60Hz 85 95 100 115 120 140 160 180 200220 240 264 L O A % ) D ( Ta= 25°C 90 100 80 70 60 50 40 (HORIZONTAL)

Derating Curve

1 2 3 4 5 +V ADJ. LED 2-M3 L=4 13 max. 7 2 .6 2 6 .6 14.65 2 5 .2 5 1 5 .1 2 8 5 1 39.1 _39.1 _11.5 62.5 2-M3 L=6

Pin No. Assignment

Single Output Switching Power Supply

R S - 1 5

20 0

-20

(3)

SPECIFICATION

INRUSH CURRENT (Typ.) LEAKAGE CURRENT SAFETY STANDARDS HARMONIC CURRENT EMS IMMUNITY WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. TEMP. COEFFICIENT VIBRATION MTBF DIMENSION OTHERS NOTE PACKING OVERLOAD OVER VOLTAGE 12V 2.1A 0 ~ 2.1A 25.2W 120mVp-p 10.8 ~ 13.2V ±1.0% ±0.5% ±0.5% 1200ms, 23ms/230VAC 80ms/230VAC 88 ~ 264VAC 47 ~ 63Hz 13.8 ~ 16.2V 79%

110 ~ 180% rated output power

Compliance to EN61000-4-2, 3, 4, 5, 6, 8,11; ENV50204, light industry level, cristeria A -20 ~ +70°C (Refer to output load derating curve)

±0.03%/°C (0 ~ 50°C)

309.7Khrs min. MIL-HDBK-217F (25°C) 78*51*28mm (L*W*H)

0.2Kg; 108pcs/15Kg/0.46CUFT

Single Output Switching Power Supply

R S - 25

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regula tion.

4. Line regulation is measured from low line to high line at rated load. RIPPLE & NOISE (max.)Note.2

•

Protections: Short circuit / Overload / Over voltage Cooling by free air convection

LED indicator for power on 100% full load burn-in test All using 105°C

Withstand 300VAC surge input for 5 second High operating temperature up to 70°C Withstand 5G vibration test

long life electrolytic capacitors

Features :

Protection type : Shut off o/p voltage, clamping by zener diode 0.4A/230VAC

UL60950-1, TUV EN60950-1 approved

emperature goes down

..

•

SAFETY &

(4)

Mechanical Specification

AMBIENT TEMPERATURE (°C) O A % ) L D ( -10 30 40 20 40 80 60 100 60 50 70

Case No.931A Unit:mm

Block Diagram

fosc : 60 KHz Terminal Pin No. Assignment

Pin No. 1 2 4 3 5 Assignment DC OUTPUT -V DC OUTPUT +V FG AC/L AC/N (HORIZONTAL)

Derating Curve

Pin No. Assignment

Single Output Switching Power Supply

R S - 25

20 0 -20 1 LED +V ADJ. 2 3 5 4 6 7 . 2 6 10.5 55 78 2-M3 L=4 2 5 .4 5 1 14 max. 2-M3 66.5 2.75 1 4 2 8 CONTROL -V +V RECTIFIERS & FILTER SWITCHING POWER FILTER & RECTIFIERS

O.L.P. PWM DETECTION_CIRCUIT

FG I/P

FILTER EMI

(5)

50W Single Output Switching Power Supply

LED indicator for power on 100% full load burn-in test

All using 105 long life electrolytic capacitors Withstand 300VAC surge input for 5 second High operating temperature up to 70 Withstand 5G vibration test

High efficiency, long life and high reliability No load power consumption<0.5W

Features :

R S - 5 0

SPECIFICATION

INRUSH CURRENT (Typ.) LEAKAGE CURRENT SAFETY STANDARDS HARMONIC CURRENT EMS IMMUNITY WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. TEMP. COEFFICIENT VIBRATION MTBF DIMENSION OTHERS PACKING OVERLOAD OVER VOLTAGE 12V 4.2 A 0 ~ 4.2 A 50.4W 120mVp-p 10.8 ~ 13.2V ±1.0% ±0.5% ±0.5% 500ms, 30ms/230VAC 60ms/230VAC 88 ~ 264VAC 47 ~ 63Hz 13.8 ~ 16.2V 84.5 %

COLD START33 A / 230VAC <2mA / 240VAC

Compliance to EN55022 (CISPR22) Class B, EN61000-3-2, -3 Compliance to EN61000-3-2,-3

±0.03%/°C (0 ~ 50°C)

309.7Khrs min. MIL-HDBK-217F (25°C) 99*97*36 mm (L*W*H)

0.41Kg; 45pcs/ 19.5Kg/ 0.9CUFT WITHSTAND VOLTAGE

ISOLATION RESISTANCE

EMC EMISSION

1. All parameters NOT specially mentioned are measured at 230VAC input, r ated load and 25°C of ambient temperature. RIPPLE & NOISE (max.)Note.2

Protection type : Hiccup mode, recovers automatically after fault condition is removed 0.8A/230VAC

SAFETY &

(6)

Mechanical Specification

_{Case No. 905B Unit:mm} AMBIENT TEMPERATURE ( ) O A % ) L D ( -2 5 -25 00 10 20 30 40 20 40 80 60 100 60 50 70

Output Derating VS Input Voltage

INPUT VOLTAGE (VAC) 60Hz 88 95 100 115 120 140 160 180 200220 240 264 O A % ) L D ( 90 100 80 70 60 50 40 (VERTICAL)

Derating Curve

Block Diagram

_{fosc : 60KHz}

Terminal Pin No. Assignment

Pin No. Pin No.

1 2 4 3 5 Assignment Assignment DC OUTPUT -V DC OUTPUT +V FG AC/L AC/N 3 .5 8 .2 3 2 1 7 5.5 74 18 6.5 87 99 89 4.5 55 20.5 1 .5 5 -M 2 3 9 .5 3.5 . 3 5 3 3 5. 2-M 3 6 7 1 .5 3 6 5 5 5 . 9 7 2 8 CIRCUIT DETECTION O.L.P. EMI FILTER RECTIFIERS & FILTER POWER SWITCHING FILTER & RECTIFIERS _+V -V I/P FG CONTROL O.V.P.

s e r i e s

Code: CLP-050A (12V dc)

50W Single Output Switching Power Supply

R S - 5 0

5 4

(7)

R S - 75

SPECIFICATION

INRUSH CURRENT (Typ.) LEAKAGE CURRENT SAFETY STANDARDS HARMONIC CURRENT EMS IMMUNITY WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. TEMP. COEFFICIENT VIBRATION MTBF DIMENSION OTHERS PACKING OVERLOAD OVER VOLTAGE 12V 6 A 0 ~ 6 A 72 W 120mVp-p 10.8 ~ 13.2V ±1.0% ±0.5% ±0.5% 500ms, 30ms/230VAC 60ms/230VAC 88 ~ 264VAC 47 ~ 63Hz 13.8 ~ 16.2V 84.5 %

COLD START 40 A / 230VAC <2mA / 240VAC

±0.03%/°C (0 ~ 50°C)

265 Khrs min. MIL-HDBK-217F (25°C) 129*97*38 mm (L*W*H)

0.41Kg; 30pcs/ 13.3 Kg/ 0.86CUFT WITHSTAND VOLTAGE

EMC EMISSION

Protection type : Hiccup mode, recovers automatically after fault condition is removed 1.2 A/230VAC

SAFETY &

Code: CLP-075A (12V dc)

75W Single Output Switching Power Supply

LED indicator for power on 100% full load burn-in test

All using 105 long life electrolytic capacitors Withstand 300VAC surge input for 5 second High operating temperature up to 70 Withstand 5G vibration test

High efficiency, long life and high reliability No load power consumption<0.5W

(8)

s e r i e s

R S - 75

Code: CLP-075A (12V dc)

75W Single Output Switching Power Supply

Mechanical Specification

_{Case No. 903 Unit:mm}

AMBIENT TEMPERATURE ( ) O A % ) L D ( -2 5 -25 00 10 20 30 45 20 40 80 60 100 60 50 70

Output Derating VS Input Voltage

INPUT VOLTAGE (VAC) 60Hz 88 95 100 115 120 140 160 180 200220 240 264 O A % ) L D ( 90 100 80 70 60 50 40 Others 3.3V,5V (HORIZONTAL)

Derating Curve

CIRCUIT DETECTION O.L.P. EMI FILTER RECTIFIERS & FILTER POWER SWITCHING FILTER & RECTIFIERS _+V -V I/P FG CONTROL O.V.P.

Block Diagram

_{fosc : 60KHz}

Pin No. Pin No.

1 2 4 3 5 Assignment Assignment DC OUTPUT -V DC OUTPU T +V FG AC/L AC/N 5 4 3 2 1 4.5 8 2. 5 9 . 9 1 3 3 3 ₈ 9 8 5 .5 3 .5 2-M 3 7 6.5 8 1 .5 5 3 . .5 3 7 7 32 3 8 2 8 .5 3 5. -3 M₃ 9 5. 1 8 Ta=25 73.5 129 122.5 120 77

(9)

R S -100

SPECIFICATION

INRUSH CURRENT (Typ.) LEAKAGE CURRENT SAFETY STANDARDS HARMONIC CURRENT EMS IMMUNITY WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. TEMP. COEFFICIENT VIBRATION MTBF DIMENSION OTHERS PACKING OVERLOAD OVER VOLTAGE 12V 8.5 A 0 ~ 8.5 A 102 W 120mVp-p 11.4 ~ 13.2V ±1.0% ±0.5% ±0.5% 500ms, 30ms/230VAC 100ms/230VAC 88 ~ 264VAC 47 ~ 63Hz 13.8 ~ 16.2V 81 %

±0.03%/°C (0 ~ 50°C)

260.8 Khrs min. MIL-HDBK-217F (25°C) 159*97*38 mm (L*W*H)

0.6Kg; 24pcs/ 15.4 Kg/ 0.7CUFT WITHSTAND VOLTAGE

EMC EMISSION

Protection type : Hiccup mode, recovers automatically after fault condition is removed 1.5 A/230VAC

SAFETY &

Code: CLP-100A (12V dc)

100W Single Output Switching Power Supply

Features :

LED indicator for power on 100% full load burn-in test All using 105

Withstand 300VAC surge input for 5 second High operating temperature up to 70 Withstand 5G vibration test

(10)

s e r i e s

R S -100

Code: CLP-100A (12V dc)

100W Single Output Switching Power Supply

Mechanical Specification

_{Case No. 901C Unit:mm}

Static Characteristics

AMBIENT TEMPERATURE ( ) L O A % ) D ( -25 0 0 20 10 30 40 20 40 80 60 100 60 50 70

INPUT VOLTAGE (VAC) 60Hz 88 95 100 115 120 140 160 180 200220 240 264 L O A D ( % ) 90 100 80 70 60 50 40 Others 3.3V,5V (VERTICAL)

Derating Curve

Block Diagram

fosc : 60KHz

Terminal Pin No. Assignment

Pin No. Pin No. 1

2

4,5 3

6,7

Assign ment Assignment DC OUTPUT -V DC OUTPUT +V FG AC/L AC/N CIRCUIT DETECTION O.L.P. EMI FILTER RECTIFIERS & FILTER POWER SWITCHING FILTER & RECTIFIERS _+V -V I/P FG CONTROL O.V.P. 4.5 9 152.5 7 150 6.5 5 1 8 . 3 .5 3.5 78 24 159 22 117 9 5 6 7 4 3 2 8 2. 6 5 2-M 3 . 9 5 2 8 .5 3 5. 1 8 -M₃ 3 ₃8 9 7 8 . 4 5 3 .5 Ta=25 1

(11)

R S -150

SPECIFICATION

MODEL RS-150-12 DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER

OUTPUT VOLTAGE ADJ. RANGE

LINE REGULATIONNote.4 LOAD REGULATIONNote.5 SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE EFFICIENCY (Typ.) AC CURRENT (Typ.) INPUT

INRUSH CURRENT (Typ.) LEAKAGE CURRENT SAFETY STANDARDS HARMONIC CURRENT EMS IMMUNITY WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. TEMP. COEFFICIENT VIBRATION MTBF DIMENSION OTHERS PACKING OVERLOAD OVER VOLTAGE 12V 12.5 A 0 ~ 12.5 A 150 W 120mVp-p 11.4 ~ 13.2V ±1.0% ±0.5% ±0.5% 800ms, 20ms/230VAC 28ms/230VAC 176 ~ 264VAC 47 ~ 63Hz 13.8 ~ 16.2V 83 %

±0.03%/°C (0~ 50°C)

244 Khrs min. MIL-HDBK-217F (25°C) 199*98*38 mm (L*W*H)

0.7Kg; 20pcs/ 15 Kg/ 0.8 CUFT WITHSTAND VOLTAGE

I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC 25°C 70%RH ENVIRONMENT

EMC EMISSION

1. All parameters NOT specially mentioned are measured at 230VAC input, r ated load and 25°C of ambient temperature.

RIPPLE & NOISE (max.)Note.2

Protection type : Hiccup mode, recovers automatically after fault condition is removed 2 A/230VAC

SAFETY &

Code: CLP-150A

(12V dc)

15 0W Single Output Switching Power Supply

LED indicator for power on 100% full load burn-in test All using 105

Withstand 300VAC surge input for 5 second High operating temperature up to 70 Withstand 5G vibration test

High efficiency, long life and high reliability long life electrolytic capacitors

Features :

(12)

s e r i e s

Mechanical Specification

Case No. 901C Unit:mm

Static Characteristics

INPUT VOLTAGE (VAC) 60Hz 88 176 19095 100200 115230 120240 132264 LO AD (%) 90 100 80 70 60 50 40 AMBIENT TEMPERATURE ( ) LO AD (%) -25 -25 00 10 20 30 40 50 60 70 20 40 60 80 100 (VERTICAL) (HORIZONTAL) 3.3V,5V Others

Derating Curve

Block Diagram

fosc : 60KHz CIRCUIT DETECTION O.L.P. EMI FILTER RECTIFIERS 230 115 & FILTER POWER SWITCHING FILTER & RECTIFIERS _+V -V I/P FG CONTROL O.V.P.

Terminal Pin No. Assignment

Pin No. Pin No.

1 2 4,5 3 6,7 Assignment Assignment DC OUTPUT -V DC OUTPUT +V FG AC/L AC/N 3.5 9 9 197 7 6.5 190 22 157 4.5 7 6 5 4 3 2 8. 2 120 199 57.5 12 9. 5 80 85 .5 98 3. 5 4-M3 3. 5 18 9. 5 18 3-M3 3.5 28 .5 38

R S -150

Code: CLP-150A

(12V dc)

15 0W Single Output Switching Power Supply

1

(13)

SPECIFICATION

DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER

INRUSH CURRENT (Typ.) LEAKAGE CURRENT SAFETY STANDARDS HARMONIC CURRENT EMS IMMUNITY WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. TEMP. COEFFICIENT VIBRATION MTBF DIMENSION OTHERS NOTE PACKING OVERLOAD OVER VOLTAGE 12V 16.7A 0 ~ 16.7A 200.4W 100mVp-p 11.4 ~ 13.2V ±2.0% ±0.5% ±0.5% 600ms, 30ms/230VAC 20ms/230VAC 85 ~ 264VAC 47 ~ 63Hz 13.2 ~ 16.2 V 79%

Compliance to EN61000-4-2, 3, 4, 5, 6, 8,11, ENV50204, EN55024, light industry level, criteria A -10 ~ +60°C (Refer to output load derating curve)

±0.05%/°C (0 ~ 50°C)

183.8Khrs min. MIL-HDBK-217F (25°C)! 199*99*50mm (L*W*H) 0.85Kg; 20pcs/17.9Kg/1.28CUFT

SP-200

I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC ENVIRONMENT

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. RIPPLE & NOISE (max.)Note.2

Features :

Protection type : Shut off o/p voltage, re-power on to recover 0.25A/230VAC

UL60950-1, TUV EN60950-1 approved OVER TEMPERATURE

95°C 5°C (TSW1: detect on heatsink of power transistor)

SAFETY & ..

•

Universal AC input / full range Built-in active PFC function, PF>0.93

Protections: Short circuit / Overload / Over voltage / Over temperature Built-in cooling fan speed control

Built-in constant current limiting circuit Built-in fan speed control

Remote ON-OFF control(Optional) LED indicator for power on 100% full load burn-in test

Fixed switching frequency at PFC:67KHz PWM:134KHz

Code: CLP-200A (12Vdc)

MODEL SP-200-12

(14)

Mechanical Specification

AMBIENT TEMPERATURE (°C) A % ) L O D (

Block Diagram

Output Derating VS Input Voltage

INPUT VOLTAGE (VAC) 60Hz

O A % ) L D ( Ta= 25°C

Derating Curve

Double Output with PFC Function

SP-200

Code: CLP-200A (12Vdc)

Case No. 916B Unit:mm

R.C. +V ADJ. LED Air flow direction 48.5 . 3 5 2 5 0 2-M4 L=5mm 142 25 133 65 117 199 35 70 20 25 15 1 6 1 1 9 9 9 9 7 5 1 1 0 3 8 9 .5 4 6-M4 L=6mm 5 2 2 5 . 1 2 5 5-M3 L=3mm 8 1 2 3 .5 9 ₅ 6 7 CN1 1 2 11 max. 4 PFC fosc : 67KHz PWM fosc : 134KHz CN1 CONTROLREMOTE

PWM & PFC DETECTION_CIRCUIT O.L.P. O.T.P. EMI FILTER RECTIFIERS CIRCUIT POWER SWITCHING FILTER CONTROL & SPEED RECTIFIERS FAN +V -V I/P FG CONTROL O.V.P. & PFC CONSTANT CURRENT LIMITING & START CIRCUIT ACTIVE FAN 85 100 115 135 155 230 264 90 100 80 70 60 50 40 10 20 30 40 50 60 (HORIZONTAL) 20 40 60 80 100 -10 0

Pin No. Pin No.

1 2

4,5

3

6,7

Assign ment Assignment

DC OUTPUT -V DC OUTPUT +V FG

AC/L AC/N

(15)

SPECIFICATION

DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER

OUTPUT VOLTAGE ADJ. RANGE

LINE REGULATIONNote.4 LOAD REGULATIONNote.5 SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE EFFICIENCY (Typ.) AC CURRENT (Typ.) INPUT

INRUSH CURRENT (Typ.) LEAKAGE CURRENT SAFETY STANDARDS HARMONIC CURRENT EMS IMMUNITY WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. TEMP. COEFFICIENT VIBRATION MTBF DIMENSION OTHERS NOTE PACKING OVERLOAD OVER VOLTAGE 12V 26A 0 ~ 26A 320 W 150mVp-p 11.4 ~ 13.2V ±1.0% ±0.2% ±0.5% 800ms, 50ms/230VAC 16ms/230VAC 88 ~ 264VAC 47 ~ 63Hz 27.6 ~ 32.4 V 87%

Compliance to EN61000-4-2, 3, 4, 5, 6, 8,11, ENV50204, EN55024, light industry level, criteria A -20 ~ +60°C (Refer to output load derating curve)

±0.03%/°C (0~ 50°C)

207 Khrs min. MIL-HDBK-217F (25°C)! 215*115*50mm (L*W*H) 1.1Kg; 12pcs/14Kg/0.92 CUFT

SP-320

I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC ENVIRONMENT

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

RIPPLE & NOISE (max.)Note.2

Features :

Protection type : Shut off o/p voltage, re-power on to recover 2.5A/230VAC

UL60950-1, TUV EN60950-1, CCC GB4943 approved OVER TEMPERATURE

80°C 5°C (TSW1: detect on heatsink of power transistor)±

SAFETY &

•

Universal AC input / full range Built-in active PFC function, PF>0.93

Protections: Short circuit / Overload / Over voltage / Over temperature Forced air cooling by built-in DC Fan

Built-in fan speed control

Fixed switching frequency at PFC:67KHz PWM:134KHz

Code: CLP-320A (12V dc)

MODEL SP-320-12

(16)

Mechanical Specification

AMBIENT TEMPERATURE (°C) LO AD (%)

Block Diagram

Output Derating VS Input Voltage

INPUT VOLTAGE (VAC) 60Hz

Ta= 25°C

Derating Curve

Pin No. Pin No. 1 2 4 ~ 6 3 7 ~ 9 Assignment Assignment DC OUTPUT -V DC OUTPUT +V FG AC/L AC/N

SP-320

Triple Output with PFC Function

Code: CLP-320A (12V dc)

Case No. 912G Unit:mm

fosc : 100KHz PWM & PFC CIRCUIT DETECTION O.L.P. EMI FILTER RECTIFIERS POWER SWITCHING FILTER & RECTIFIERS _+V -V I/P FG CONTROL O.V.P. O.T.P. INRUSH CURRENT ACTIVE LIMITING FAN FAN CONTROL SPEED 13 5 _9.5 8 5 +V ADJ. 4-M4 L=5mm 5-M3 L=3mm 1 2 3 4 5 6 7 8 9 27.5 19 177.5 32.5 150 117.5 15 16 10 95 50 32 .5 37 .5 ₅₀.5 11 5 36 .7 150 215 6-M4 L=5mm 25 50 14 max. Air flow direction 32.5 LED 48.7 90 88 95 100 115 135 155 175 195 230 264 300 250 200 150 100 50 25 10 20 30 40 50 60 70 20 40 60 80 100 -20 0 (HORIZONTAL) 90 100 80 70 60 50 40 Others