403.287.3252 www.lambertpaving.com
– 1 –
MATERIAL SAFETY DATA SHEET FOR MICRO PAVE 2000
Material Safety Data Sheet – Micro Pave 2000
WHMIS TDG
D-2B Not a Dangerous Good
Section 1. Product Identification and uses
Common Name: Micro Pave 2000
Synonyms: None
Chemical Family: Anionic Slow Setting Emulsified Asphalt Material Use: Asphalt Sealer
Supplier/manufacturer: Lambert Bros. Paving: 4620 Manilla Road SE, Calgary, AB T2G 4B7 (403) 287-3252
Section 2
.First Aid Measures
Eye Contact: Flush eyes immediately with water for at least 15 minutes. Seek medical attention if irritation persists.
Skin contact: Remove contaminated clothes and seek medical attention if irritation develops.
Inhalation: Move to fresh air source. If stopped breathing start CPR. Seek medical attention Ingestion: Seek medical attention.
Section 3: Hazardous Ingredients
Components CAS Number % by Mass Exposure Limits
Asphalt 8052-42-4 40-70 5mg/m3
Petroleum Distillate Mixture Not available 02 100ppm
Water Balance
Note: This product is a liquid in which asphalt is dispersed as stable droplets in an anionic soap solution.
Section 4: Physical Data
Boiling point Melting point Pour point Vapor pressure Vapor Density
Approx: 100 C Approx: 0 C Not Available Not Available Not Available
Specific Gravity Solubility in Water Physical State % by volume at 260 C
1.02 @ 15 C Soluble Liquid Water 30-40% Organic:0-1%
Appearance and odor Odor Threshold Viscosity @ 25 C
Dark brown creamy liquid. Bland resinous odor.
Section 5: Fire and Explosion Data
Flash point (test method) Auto Ignition Temperature Lower Flammable Limits Upper Flammable Limits
Above 104 C Not Applicable Not Applicable Not available
Fire Extinguishing Substances
Foam Carbon Dioxide Dry Chemical Use full protective gear and equipment
Self-contained breathing apparatus in closed areas Class B fire.
Unusual Fire and Explosion Hazards Sealer will not burn under prolonged exposure Explosion/Sensitivity Data
Stable under normal conditions of temperature and pressure.
403.287.3252 www.lambertpaving.com
– 2 –
Material Safety Data Sheet – Micro Pave 2000 Section 6: Reactivity Data for Product
Stability Stable
Incompatibility Strong oxidizing agents.
Conditions to avoid (Stability)
Contact with above materials. Heating to dryness and than 200 C. Contact with strong acid.
Hazardous Decomposition Products
Hazardous combustion products include carbon dioxides (CO2, CO) Storage precautions
Avoid heating above 80 C.
Avoid breathing vapors or mist.
Section 7: Toxicological Data and Health Hazard Information
Eye Contact Eye irritation may result from prolonged exposure to liquid or vapor.
Skin Contact Low toxicity. Frequent or prolonged contact may irritate skin and cause skin rash. (dermatitis) Inhalation Inhalation of vapors or mist may cause central nervous system depression, headaches, nausea, or,
dizziness.
Ingestion May irritate gastrointestinal tract and cause nausea and vomiting.
Toxicity Not available.
Chronic Effects None known Irritancy/Sensitization Not available
Section 8: Preventive Measures
Ventilation Requirements Under normal circumstances ventilation is not required. If indoors local exhaust is normally adequate.
Respiratory Protection Normally not required. Poorly ventilated areas, use approved organic vapor cartridge respirators.
Eye Protection Chemical goggles if splashing is likely to occur.
Skin Protection Chemical resistance gloves, apron and other clothing is suggested.
Waste Disposal Dispose in accordance to local law enforcement codes.
Storage Store in a sealed container. Do not freeze. Long term storage may require re-circulation.
Spill or leak Cover with sand or other suitable material and let dry.
Section 9: Preparation Information
Prepared by Lambert Bros. Paving
Date of preparation June 5 2000
Emergency Telephone Number: (403) 287-3252
While the company believes the data set forth herein are accurate as of the date hereof, the company makes no warranty with respect thereto and expressly disclaims all liability for reliance thereon. Such data are offered solely for your consideration, investigation, and verification.
403.287.3252 www.lambertpaving.com
– 3 –
403.287.3252 www.lambertpaving.com
– 4 –
403.287.3252 www.lambertpaving.com
– 5 –
403.287.3252 www.lambertpaving.com
– 6 –
403.287.3252 www.lambertpaving.com
– 7 –
Performance Graded Asphalt Cement Page 1 of 3
1. PRODUCT MANUFACTURER / MSDS PREPARATION INFORMATION
Product Manufacturer/Supplier: McAsphalt Industries Ltd.
8800 Sheppard Ave. East Scarborough, ON M1B 5R4 (416) 281-8181
MSDS Prepared By: Operations Department
Products: i) SHRP or Performance Graded (PG); (ii) Asphalt Cement (3GR)
(iii) Performance Graded (AS) by grade PG 46-34, PG 46-40, PG
52-28, PG 52-34, PG 52-40, PG 58-22, PG 58-28, PG 58-34, PG 64-22, PG 64-28, PG 64-34, PG 70-22, PG 70-28, PG58-28HRD, PG64-34HRD, PG58-34HRD
Suffix (AS) indicates anti-strip agent added
Product Use: Asphalt for paving purposes
Revision Date: March 15, 2013
Supersedes: October 19, 2011
EMERGENCY NUMBER: CANUTEC – (613) 996-6666
WHMIS: Not Controlled
TDG: Not Regulated
Workplace Label: Health-2; Fire-0; Reactivity-0; Compliance Center-P
2. INGREDIENTS / COMPOSITION
COMPONENT(S) CAS # % (w/w) LD50 LC50 PIN
Asphalt 8052-42-4 99 - 100% N/A N/A N/A
Antistripping additive added in quantities <1% when indicated. Heated product may evolve vapors irritating to the nose, throat and lungs. See preventative measures.
3. PHYSICAL DATA
Physical State: Semi-solid Appearance: Black
Specific Gravity: 1 .027@ 15°C Odor: Asphalt type odor
Freezing Point: N/A Odor Threshold: N/A
Boiling Point: N/A Solubility in H2O: negligible Vapour Pressure: < 0.1 Evaporation Rate: negligible
Vapour Density: > 1.0 pH: N/A
Material Safety Data Sheet Performance Graded Asphalt Cement
Performance Graded Asphalt Cement Page 1 of 3
1. PRODUCT MANUFACTURER / MSDS PREPARATION INFORMATION
Product Manufacturer/Supplier: McAsphalt Industries Ltd.
8800 Sheppard Ave. East Scarborough, ON M1B 5R4 (416) 281-8181
MSDS Prepared By: Operations Department
Products: i) SHRP or Performance Graded (PG); (ii) Asphalt Cement (3GR)
(iii) Performance Graded (AS) by grade PG 46-34, PG 46-40, PG
52-28, PG 52-34, PG 52-40, PG 58-22, PG 58-28, PG 58-34, PG 64-22, PG 64-28, PG 64-34, PG 70-22, PG 70-28, PG58-28HRD, PG64-34HRD, PG58-34HRD
Suffix (AS) indicates anti-strip agent added
Product Use: Asphalt for paving purposes
Revision Date: March 15, 2013
Supersedes: October 19, 2011
EMERGENCY NUMBER: CANUTEC – (613) 996-6666
WHMIS: Not Controlled
TDG: Not Regulated
Workplace Label: Health-2; Fire-0; Reactivity-0; Compliance Center-P
2. INGREDIENTS / COMPOSITION
COMPONENT(S) CAS # % (w/w) LD50 LC50 PIN
Asphalt 8052-42-4 99 - 100% N/A N/A N/A
Antistripping additive added in quantities <1% when indicated. Heated product may evolve vapors irritating to the nose, throat and lungs. See preventative measures.
3. PHYSICAL DATA
Physical State: Semi-solid Appearance: Black
Specific Gravity: 1 .027@ 15°C Odor: Asphalt type odor
Freezing Point: N/A Odor Threshold: N/A
Boiling Point: N/A Solubility in H2O: negligible Vapour Pressure: < 0.1 Evaporation Rate: negligible
Vapour Density: > 1.0 pH: N/A
Material Safety Data Sheet
Performance Graded Asphalt Cement
403.287.3252 www.lambertpaving.com
– 8 –
Performance Graded Asphalt Cement Page 2 of 3
4. FIRE & EXPLOSION HAZARD
Flash Point & Method: > 230°C (COC) Lower/ Upper Flammability Limit: N/A
Auto-Ignition Temperature: > 400°C
Fire Fighting Media: Foam, Dry Chemical, Water spray with caution
Explosion/Flammability: N/A
Hazardous Combustion Products: CO, NOx, SOx, sulfur products
5. REACTIVITY DATA
Stability: Stable
Incompatible Materials: Water, or materials with low flash points Conditions of Reactivity: N/A
Hazardous Decomposition Products: CO, SOx, NOx, other Sulphur compounds
Synergistic Products: None
6. HEALTH HAZARD INFORMATION
Skin: Can cause skin irritation, dermatitis. Skin defeating with chronic exposure
Eyes: Danger when hot
Inhalation: Yes
Exposure Limit: 5mg/M3 Asphalt fumes, caution in confined spaces
Ingestion: Unlikely, should be avoided
No known carcinogenic, teratogenic or reproductive effects.
7. PREVENTATIVE MEASURES
Personal Protective Equipment: Gloves, goggles, face shield when handling hot.
Handling/Shipping/Storage: Containers cleaned thoroughly before use. Hydrogen Sulfide concentrations may build in heated storage tanks
Ventilation: Ensure adequate ventilation
Disposal: See appropriate federal, provincial, municipal regulations LEAKS AND SPILLS: Contain with earth or sand, allow cooling and hardening.
Eliminate sources of ignition. Notify authorities when in water, or large spills.
8. FIRST AID
SKIN: DO NOT REMOVE HOT ASPHALT FROM BURN! Cool in water and
if irritation persists seek medical aid
EYES: Gently flush with lots of water. Seek Medical Help.
INHALATION: Remove victim to fresh air. Seek Medical Help.
INGESTION: Give lots of water to drink. Seek Medical Help. Performance Graded Asphalt Cement Page 2 of 3
4. FIRE & EXPLOSION HAZARD
Flash Point & Method: > 230°C (COC) Lower/ Upper Flammability Limit: N/A
Auto-Ignition Temperature: > 400°C
Fire Fighting Media: Foam, Dry Chemical, Water spray with caution
Explosion/Flammability: N/A
Hazardous Combustion Products: CO, NOx, SOx, sulfur products
5. REACTIVITY DATA
Stability: Stable
Incompatible Materials: Water, or materials with low flash points Conditions of Reactivity: N/A
Hazardous Decomposition Products: CO, SOx, NOx, other Sulphur compounds
Synergistic Products: None
6. HEALTH HAZARD INFORMATION
Skin: Can cause skin irritation, dermatitis. Skin defeating with chronic exposure
Eyes: Danger when hot
Inhalation: Yes
Exposure Limit: 5mg/M3 Asphalt fumes, caution in confined spaces
Ingestion: Unlikely, should be avoided
No known carcinogenic, teratogenic or reproductive effects.
7. PREVENTATIVE MEASURES
Personal Protective Equipment: Gloves, goggles, face shield when handling hot.
Handling/Shipping/Storage: Containers cleaned thoroughly before use. Hydrogen Sulfide concentrations may build in heated storage tanks
Ventilation: Ensure adequate ventilation
Disposal: See appropriate federal, provincial, municipal regulations LEAKS AND SPILLS: Contain with earth or sand, allow cooling and hardening.
Eliminate sources of ignition. Notify authorities when in water, or large spills.
8. FIRST AID
SKIN: DO NOT REMOVE HOT ASPHALT FROM BURN! Cool in water and
if irritation persists seek medical aid
EYES: Gently flush with lots of water. Seek Medical Help.
INHALATION: Remove victim to fresh air. Seek Medical Help.
INGESTION: Give lots of water to drink. Seek Medical Help.
403.287.3252 www.lambertpaving.com
– 9 –
Performance Graded Asphalt Cement Page 3 of 3
9. NOTE
The information contained herein relates only to this product or material and may not be valid when used in combination with any other product or material or in any process. If the process is not to be used under conditions, which are normal or reasonably foreseeable, this information cannot be relied upon as complete or applicable. The information contained herein is based upon the information available at the indicated date of preparation, the above supplier assumes no liability whatsoever for the accuracy or completeness of the information.
Performance Graded Asphalt Cement Page 3 of 3
9. NOTE
The information contained herein relates only to this product or material and may not be valid when used in combination with any other product or material or in any process. If the process is not to be used under conditions, which are normal or reasonably foreseeable, this information cannot be relied upon as complete or applicable. The information contained herein is based upon the information available at the indicated date of preparation, the above supplier assumes no liability whatsoever for the accuracy or completeness of the information.
