LAMA
has developed over the years a wide range of products that can be used in the waterproofing and damp-proofing of roofs, decks, car parkings, walls, foundations, basements, roads,…etc. In this catalogue, there are five main Product categoriesWATERPROOFING MEMBRANES
WATERPROOFING & PROTECTIVE COATINGS SEALANTS
WATERPROOFING MEMBRANES
Confirms to the Requirements of EN 13707REINFORCED FIBERGLASS
APP Modifi ed Bitumen Membrane
Description
Most economical waterproofing 3 or 4mm thick membrane,
Excellent resistance to heat aging and weathering, Dimensional stability to membrane sheet due to the reinforcement of a rot-proof fiberglass mat 60g/m2.
Technical specifications
Dimensions 1×10 m Roll Thickness 3 or 4mmCold Pliability no cracking at -5ºC Softening Point 150ºC±10
Penetration 20±10 dmm
OGV
WATERPROOFING MEMBRANES
Spunbond Polyester
APP Modifi ed Membrane
Description
A bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester 150g/m2, High performing membrane,
Excellent durability, flexibility and resistance to weathering and salt solutions, dilute acids.. etc. Fast, easy and clean application can be applied on existing asphalt roofing systems.
Technical specifications
Dimensions 1×10 m Roll Thickness 3 or 4mmCold Pliability no cracking at -5ºC Softening Point 150ºC ±10
WATERPROOFING MEMBRANES
APP Modifi ed Bitumen Membrane
Description
A bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester 180g/m2, High performing membrane,
Excellent durability, flexibility and resistance to weathering and salt solutions, dilute acids.. etc. Fast, easy and clean application can be applied on existing asphalt roofing systems.
Technical specifications
Dimensions 1×10 m Roll Thickness 3, 4 or 5mm Cold Pliability no cracking at -8ºC Softening Point 150ºC ±10Penetration 20±10 dmm
WATERPROOFING MEMBRANES
SPUNBOND POLYESTER
APP Modifi ed Bitumen Membranes
Description
A bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester 200g/m2, Most suitable for use in TROPICAL areas,
Excellent durability, flexibility and resistance to weathering and salt solutions, dilute acids.. etc. Fast, easy and clean application can be applied on existing asphalt roofing systems.
Technical specifications
Dimensions 1×10 m Roll Thickness 3, 4 or 5mmCold Pliability no cracking at -12ºC Softening Point 150ºC ±10
WATERPROOFING MEMBRANES
SPUNBOND POLYESTER
APP Modifi ed Bitumen Membranes
Description
A bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester 200g/m2, High performing membrane,
Excellent weathering and ageing resistance. High flexibility at low temperatures.
High puncture, tear, and Hydrostatic pressure resistance.
Technical specifications
Dimensions 1×10 m Roll Thickness 3, 4 or 5mmCold Pliability no cracking at -15ºC Softening Point 150ºC ±10
Penetration 20±10 dmm
WATERPROOFING MEMBRANES
Spunbond Polyester APP Modifi ed
Membrane
Description
A bituminous waterproofing membrane, reinforced with Non-woven Spunbonded Polyester of
different weights to give the needed elongation, High performing membrane,
Resistance to heat aging, puncture, and rotting Excellent durability, flexibility and resistance to weathering and salt solutions, dilute acids.. etc. Fast, easy and clean application can be applied on existing asphalt roofing systems.
Technical specifications
Dimensions 1×10 m Roll Thickness 3, 4 or 5mmCold Pliability no cracking at (-5) – (-10) ºC depending on the reinforcement Softening Point 150ºC ±10
WATERPROOFING MEMBRANES
SPUNBOND POLYESTER
SBS Modifi ed Bitumen Membranes
Description
Modified with Styrene Butadiene Styrene (SBS) and reinforced with Non-woven Spunbonded Polyester ranging from 180g/m2 to 200g/m2, Excellent elasticity,
High aging, puncture, and tear Resistance
Good resistance to acids, sulphates and chlorides. High flexibility at low temperatures.
Technical specifications
Dimensions 1×10 m Roll Thickness 3, 4 or 5mmCold Pliability no cracking at (-15) – (-20) ºC Softening Point 130ºC ±10
Penetration 25±10 dmm
WATERPROOFING MEMBRANES
DOUBLE REINFORCEMENT
APP Modifi ed Bitumen Membrane
Description
Made with a double reinforcement of 180 g/m² non-woven polyester and 60 g/m² fiberglass, High dimensional stability,
High thermal aging, and puncture Resistance Withstanding extreme temperatures.
Technical specifications
Dimensions 1×10 m Roll Thickness 4 or 5 mm
Cold Pliability no cracking at -5 ºC Softening Point 150 ºC ±10
WATERPROOFING MEMBRANES
DOUBLE-REINFORCEMENT
APP Modifi ed Bitumen Membranes
Description
Made with a double reinforcement of 200 g/m² non-woven polyester and 60 g/m² fiberglass, Used in heavy duty applications
High dimensional stability,
High thermal aging, and puncture Resistance Hydrostatic pressure and Load strain resistance.
Technical specifications
Dimensions 1×10 m Roll Thickness 4 or 5 mm
Cold Pliability no cracking at -10 ºC Softening Point 150 ºC ±10
Penetration 20 dmm
WATERPROOFING MEMBRANES
Bridge Deck Waterproofi ng Membranes
Description
Made with a double reinforcement of 250 g/m² non-woven polyester and 60 g/m² fiberglass, Designed for use in road works,
High dimensional stability,
Puncture & tear, Impact, and Fuel Resistance.
Technical specifications
Dimensions 1×10 m Roll Thickness 4 or 5 mm
Cold Pliability no cracking at -5 ºC Softening Point 155 ºC ±10
WATERPROOFING MEMBRANES
Anti-Root Waterproofi ng Membrane
Description
Made with 180 or 200 g/m2 nonwoven polyester fabric reinforced with fiberglass filaments,
Bitumen is specially treated with an antiroot formulation, with the addition of Preventol B2 Used in areas where plantation can damage the waterproofing layers (Plant root resistance) High dimensional stability,
Excellent elasticity
High Puncture & tear Resistance,
Resistance to aging, acids, sulfates and chlorides.
Technical specifications
Dimensions 1×10 m Roll Thickness 3, 4 or 5 mm
Cold Pliability no cracking at -10 ºC Softening Point 150 ºC ±10
Penetration 20±10 dmm
WATERPROOFING MEMBRANES
Bituminous Protection Board
Description
Semi rigid protection board, covered on both sides with a polyethylene film
Protect the waterproofing membrane from construction abuse and harmful puncture. It gives protection against normal foot traffic as well as the wearing caused by built-up over layers for horizontal surfaces
Protection against rotting and decomposing Tough and durable protective cover for protecting various waterproofing systems.
Technical specifications
Dimensions 1×2 m Board or 1×10 Roll Thickness 3, 4, 5 and 6 mm
WATERPROOFING & PROTECTIVE COATINGS
Highly Penetrative Bituminous Primer
Properties
Solvent base cold applied, highly penetrative thin bituminous solution, black in color.
Used for priming concrete, masonry, metal, asphalt surfaces, and as a priming coat before applying any LAMA bituminous coating, or modified bitumen membrane.
Complies with the requirements of ASTM D 41 Type I.
Covers from 2-3 m²/liter dependent upon porosity of surface.
Supplied in 20 and 200 liter drums.
Technical specifications
Flash point 40 ºC Penetration @ 25 ºC 20-50 dmm Viscosity @25 ºC 25-125 s
WATERPROOFING & PROTECTIVE COATINGS
Asphalt Roof Coating (Regular and Fast
Drying)
A solvent-born bituminous compound of brushable consistency, dries to a tough, black coating, which does not flow under summer heat. A general purpose waterproofing and damp-proofing coating.
Used as a primer where concrete surfaces are porous
Provides protection against corrosion.
Recommended where the threat of frost or rain precludes the use of an emulsion
Complies with the requirements of ASTM D4479 Type II and BS 3416.
Covers approximately 1.6 m²/liter. Supplied in 20 and 200 liter drums.
Technical specifications
Flash point 60 ºC Specific gravity 0.90
WATERPROOFING & PROTECTIVE COATINGS
Rubberized Bitumen Emulsion,
Waterproofer and Adhesive
A dark brown cold applied rubberized bitumen emulsion, dries to form a black flexible coating. Used as a water and moisture barrier, an adhesive, a plaster bonding agent and a primer.
Provides protection against metal corrosion Provides weatherproofing layer when used over exposed insulation
Complies with the requirements of ASTM D 1227, Type III, Class 1
Covers approximately 1.3 m²/liter.
As a Primer it covers approximately 5 m²/liter. Supplied in 20 and 200 liter drums.
Technical specifications:
Specific gravity 980-1040 Residue by evaporation 47-53 %WATERPROOFING & PROTECTIVE COATINGS
Protective Fibrated Coating
A dark brown cold applied asphalt emulsion prepared emulsifying agents and containing non-asbestos fibers, for reinforcement.
Used as a water and moisture barrier, also as a vapor barrier.
Provides protection against metal corrosion Provides weatherproofing layer when used over exposed insulation
Complies with the requirements of ASTM D 1227 type II, class 1.
Covers approximately 2 m²/liter. Supplied 20 liter drums.
Technical specifications
Specific gravity 980 – 1080 Residue by evaporation 45 – 55 %
WATERPROOFING & PROTECTIVE COATINGS
Below Ground Asphalt Coating
Cutback petroleum asphalt of rapid curing type, and of brushable consistency. Dries to tough, highly adhesive, black coatings.
Resists the attack of salt solutions, sulphates, and dilute acids.
A general purpose waterproofing coating.
Complies with the requirements of ASTM D4479 Type 1.
Covers approximately 1.0 m²/liter. Supplied in 20 and 200 liter drums.
Technical specifications
Viscosity 100-220 sec. Penetration @ 25 ºC 80-120 dmm. Flash Point 27 ºC
WATERPROOFING & PROTECTIVE COATINGS
Bituminous High Elastic Rubberized
Coating
Cold applied bituminous rubberized solvent based compound, black in color.
Excellent and full adhesion to concrete surfaces. High elasticity.
Self-repairing in case of a little puncture. Moisture resistant.
Covers approximately 1.0 m²/liter. Supplied in 20 liter drums.
Technical specifications
Flash point 40 ºC Elongation 1000/100WATERPROOFING & PROTECTIVE COATINGS
Crack Bridging and Protective Coating
System For Concrete and Masonry
Waterproofing elastomeric and durable white emulsion.
Provides a protective and reflective layer to the coated surface.
For heat and sound insulation, waterproof and anti-rust protection.
High solar reflectivity and U.V. resistance. Frost, de-icing salts and CO2 resistance. Complies with the requirements of AWWA C-203.
Covers approximately 1.0 m²/liter. Supplied in 20 liter drums.
Technical specifications:
Elongation at 25 °C Over 300% Service temperature -5 to 80 ˚C. Solids contents 62%
WATERPROOFING & PROTECTIVE COATINGS
Bituminous Aluminum Coating
A light/heat reflective and decorative coating. Asphalt base, aluminum-pigmented non-fibered protective coating dries to a bright silvery finish. for use over bituminous coatings, modified bitumen roofs, metal roofs, primed steel and masonry walls.
Complies with the requirements of ASTM D 2824, type I.
Covers approximately 0.8-1 m²/liter. Supplied in 20 liter drums.
Technical specifications
Flash point 38 °C Reflectance 70%WATERPROOFING & PROTECTIVE COATINGS
Stone Water Repellent
A transparent liquid.
Closes the pores and forms a water repellent layer inside the element and at the surface while permitting the trapped vapor to move out. For coating stone, concrete, asbest-cement, and brick
Resistant to salt solutions, dilute acids, alkalis and U.V. Covers approximately 4 m²/liter depending on the concrete or stone porosity..
Supplied in 20 liter drums.
Technical specifications
Specific gravity about 0.8WATERPROOFING & PROTECTIVE COATINGS
Highly Elastic Rubberized Liquid
Membrane
Properties
A liquid cold applied bituminous membrane, black in color.
used to resist the plant root penetration and designed for use in planted roofs
Rubberized solvent based compound of a very high elasticity and Highly adhesive
Good resistance to acids, sulfates and chlorides. High flexibility at low temperatures
Bonds to asphalt and bitumen surfaces, ideal for repair of failed and aged coatings
Resistance to aging Supplied in 20 liter drums.
Technical specifications
Flash point 40 ºC Softening Point 95 ºCBONDING ASPHALT
BLOWN ASPHALT
85/25 & 115/15 for Built-up Roofi ng
Properties
Produced by air blowing of petroleum residues. The grade depends on the softening point and the penetration degree.
Used in the construction of built up roofing as bonding or flood coats.
Complies with the requirements of B.S 3690: part 2, ASTM D312: Type III & Type IV, and Jordanian National Building code (Vol. ll-Ch5) Tables No. 15 & 17.
BONDING ASPHALT
For MASTIC ASPHALT on Roofs
Properties
Produced by air blowing of petroleum residues. It is mixed in-place with other components like limestone aggregate, cement and hydrated lime to give a waterproofing material, solid or semi-solid under normal weather conditions.
Softens gradually when heated to 200°C, so it can be spread easily on the roofs.
Used in the construction of built-up roofing as waterproofing and adhesive layer
Type I & IV complies with ASTM D 312. Supplied in 180 kg steel drums.
Technical specifications
Penetration @ 25 ºC 18-60 (Type I), 12-25
(Type IV)
Softening Point 57-66 (Type I), 99-107
(Type IV).
MASTICS AND SEALANTS
Hot Poured Elastic Concrete Joint Sealer
Properties
Hot poured sealant composed of special asphalt, plasticizers, rubber and fillers.
Used for sealing joints.
Excellent Adhesion, Good Elasticity, and Water Resistance.
Use 1200g for 1000cc.
Complies with the requirements of B.S 2499, Type N1, ASTM D1190, ASTM D3405, ASSHTO M-173, and ASSHTO T-187
Supplied in 5 gallon drum and 20 kg block..
Technical specifications
Flash point 250 ºC min. Softening Point 100 ºC min. Penetration @ 25 ºC 90 dmm max
MASTICS AND SEALANTS
Concrete Joint Sealer, Hot-Poured Elastic
Type
Properties
A black resilient and adhesive compound. effectively sealing joints in concrete against penetration of moisture and foreign material Excellent adhesion to bitumen and concrete surfaces.
Good elasticity, High water resistance, and Weather resistant
Use 1300g for 1000cc.
Complies with the requirements of B.S. 2499 (Type N2).
Supplied in 20 liter steel drums.
Technical specifications
Specific gravity 1.20
MASTICS AND SEALANTS
Cold Applied, Sealant
Properties
A blend of special asphalts, plasticizer and fillers. Soft for easy use, highly elastic and weather proof. Good adhesion without primer.
Used for easy and fast sealing.
Complies with the requirements of ASTM C920, Grade NS.
Supplied in 20 liter drums.
Technical specifications
Specific gravity 1.20 Softening Point 80 ºC min. Penetration @ 25 ºC 85 dmm max
MASTICS AND SEALANTS
Trowel-Applied Asphalt Roof Cement
Properties
A black bituminous paste consists of an asphalt base, solvents, mineral stabilizers and fibers. Suitable for application by trowel or spatula. For sealing joints and cracks in bituminous membranes, concrete and other surfaces.
Protect metallic surfaces and dampen their noise. Covers 0.3 m²/liter (giving 3 mm wet thickness) Complies with the requirements of ASTM D4586, Type II.
Supplied in 20 liter drums.
Technical specifications
WATERPROOFING & DAMPPOOFING FELTS
LAMAFELT-18
Organic Fiber Base for Damp Proof Course
Consists of a sheet of matted organic fibers impregnated with asphalt and coated on both faces with blown bitumen and covered with fine granules. used in built-up roofing and as a vapor barrier under roof insulation
Complies with the requirements of BS 747 type 1B.
LAMAFELT-36
Glass Fiber Base for Damp Proof Course
WATERPROOFING & DAMPPOOFING FELTS
LAMA PERFOFELT
Glass Fiber Base
A glass fiber mat with 40 mm diameter perforations saturated with asphalt and coated with bitumen and covered with fine granule surfacing material. Used primarily as a venting base sheet in built-up roofing and may be used as a loosely laid layer over the prepared substrate, beneath the torch applied LAMA waterproofing membrane.
LAMA POLYFELT
For Roofi ng and Waterproofi ng
Non-woven polyester mat saturated with oxidized bitumen and faced on the upper side with fine granule and on the bottom side with polyethylene sheet. Excellent durability, resistant to germs and yeasts, and highly flexibility.
WATERPROOFING & DAMPPOOFING FELTS
LAMA MESH
Fiberglass Net 70
A fiberglass net of excellent site serviceability, specially designed for use as a reinforcement of waterproofing coats for the roofs and foundations, to reinforce marble slabs of vertical walls and surface layers, and reinforcing cold and hot asphalt coats. It doesn’t dissolve with the organic solvents in the asphalt and it is a rot and fungi proof.
LAMA PAPERFELT
Asphalt-Saturated Organic Felt
WATERPROOFING & DAMPPOOFING FELTS
LAMA JUTE
For Roofi ng and Waterproofi ng
OTHER PRODUCTS
STEELCOAT
For protecting iron and steel
A hot applied bitumen based coating with inert non-fibrous fillers. It is solid at the normal
temperatures, and softens gradually when heated turning into a very viscous liquid at about 130˚C. At higher temperatures the viscosity drops, turning the mixture into a thin and easy to apply liquid. Used to provide a protective layer over steel pipes and fittings against corrosion. Complies with requirements of the BS4147: Type A-Grade B.
STEELPRIME
For protecting iron and steel
A primer for cold application over iron and steel, consisting of a homogeneous solution of bitumen in a fast drying solvent. When dry, it provides an effective bond between the metal and the subsequent coating. Complies with the requirements of BS4147: Type A-Grade B.