• No results found

3-Port FireWire 800/400 PCI Host Card

N/A
N/A
Protected

Academic year: 2021

Share "3-Port FireWire 800/400 PCI Host Card"

Copied!
12
0
0

Loading.... (view fulltext now)

Full text

(1)

Upgrade to FireWire800 !

FireWire

3-Port FireWire 800/400 PCI Host Card

U S E R ’ S M A N U A L

FireWire

Included

Low

400

400

FireWire

Included

Low

(2)

Package Contents :

1

3-Port FireWire 800/400 PCI Host Card

2

Low Profile Bracket

3

Driver CD

4

User’s Manual

TRADEMARKS

MS-DOS,Microsoft, Windows NT/2000/ME/XP/Vista are trademarks of Microsoft Corporation.

Apple, Macintosh and Mac are trademarks of Apple Computer.

*All other third-party brands and names are the property of their respective owners.

Low Profile Bracket 2

4

User’s

Manual

U S E R ’ S M A N U A L 400 FireWire

Included Low

3

Driver CD

1

(3)

1. Introduction ...02

2. Specifications / Features ...03

3. System Requirements / Parts Layout ...04

4. Installation

3-Port FireWire 800/400 PCI Host Card

4.1 Hardware Installation ...05 4.2 Driver Installation ...08

5. Warranty / Contact ...10

1

Table of Contents :

Introduction

(4)

Introduction 2

Introduction Take advantage of the high-speed FireWire 800

with Vantec’s 3-Port FireWire 800/400 PCI Host Card. It allows you to easily add two FireWire 800 (IEEE 1394b) as well as one FireWire 400 ( IEEE 1394a ) ports to your PC or MAC® offering speeds up to 800 Mbps. Download, edit, and connect DV c a m c o r d e r , digital camera , hard drive and daisy - chain up to 63 devices. Compatible with Windows® 98SE/ME/2000/XP/Vista and MAC®OSX10.4 or higher, the Vantec 3-Port FireWire 800/400 PCI Host Card is the choice for your FireWire needs.

1. Introduction :

FireWire 800/400

3-Port FireWire 800/400 PCI Host Card

(5)

Specifications/Features 3

2. Specifications / Features :

Features :

• Two FireWire 800(1394b) ports

• One FireWire 400(1394a) port

• PCI 2.2 compliant and works in 32/64-bit PCI slot

• Support data transfer rates of 100, 200, 400, and 800 Mbps

• Built-in 4-Pin power connector for reliable power output

• Low profile bracket included for low profile chassis

• Supports Hot-Swap and Plug & Play

• RoHS compliant

Specifications :

• Model: UGT-FW100

• Bus Type: 32-Bit 33 MHz PCI v2.2

• Port Type: 2 FireWire 800(1394b) Ports 1 FireWire 400(1394a) Port

• OS Support: Windows® 98SE/ME/2000/XP/Vista MAC® OS V10.4 or higher

FireWire 800(1394b) Ports FireWire 800(1394b) Ports

FireWire 400(1394a) Port

IEEE1394a1394b

(6)

System Requirements / Parts Layout 4

3. System Requirements / Parts Layout :

FireWire 800(1394b) Ports FireWire 800(1394b) Ports

FireWire 400(1394a) Port

Parts Layout:

PC Users Mac Users

Gold contact pins

• Mac G3 processor & greater

• Mac OS V10.4 or higher

• 128MB RAM or higher

• PCI slot that complies with PCI Specification Rev.2.0 or above

• Intel Pentium III or higher compatible processor

• Microsoft Windows 98SE / ME / 2000 / XP / VISTA

• 128MB RAM or higher

• PCI slot that complies with PCI Specification

Rev.2.0 or above

(7)

4.1. Hardware Installation :

PC Users

(1) Turn off your computer and disconnect all external peripheral devices and cables, i.e.

power cord, network cable, monitor, etc.

(2) Remove your computer’s cover. For most standard PC’s, there are screws that will need to be unseated before you can remove the computer’s cover, and these screws are usually located at the rear of the computer, along the edge of the cover.

However, placement of these screws and cover attachment may vary by manufacturer, so please refer to your computer system’s manual for specific details.

(3) Once you have removed the cover, you will need to locate the PCI slots on the motherboard.

The PCI slots are generally located in the back of the computer, with the slots built into the side-wall of the computer ( please refer to your computer system’s manual for the exact location of your PCI slots or refer to the

Installation 5

4. Installation :

diagram in this manual – the Vantec FireWire

800 PCI Card may be installed in either a 32 or

64-bit PC card slot). If necessary, you may

need toI remove the expansion slot cover,

(8)

Installation 6

4. Installation :

(4) Take the Vantec FireWire PCI Card out of its anti-static bag and push the card into the empty PCI card slot. The card should be mounted with the circuitry facing down. This is the only way to mount the card, so if you are having problems inserting the card into the PCI slot, make sure that it is oriented correctly. Be sure that the gold contact pins of the PCI card are seated completely inside your computer’s PCI slot.

Be aware that it may take some force to get the card fully seated in the slot.

(5) Once the PCI card is seated correctly, tighten with a screw, and, if necessary, replace any peripherals that you removed in Step 3.

(6) Now you are ready to put the computer’s cover back on and reconnect all of your external peripheral devices and cables.

(7) Power on your computer. After the start up procedure has finished, you should be able to connect devices through the available FireWire ports.

and you may also need to remove any add-in

boards which may block the access to the

PCI slots.

(9)

Installation 7

4. Installation :

(1) Turn off your computer and disconnect all external peripheral devices and cables, i.e. power cord, network cable monitor, etc.

(2) Remove your computer’s cover by pulling the latch on the side, and gently lower the side of the computer onto a flat, non-abrasive surface.

(3) Once you have removed the cover, you will need to locate the PCI slots on the motherboard. The PCI slots are generally located in the back of the computer, with the slots built into the side-wall of the computer (please refer to your computer system’s manual for the exact location of your PCI slots). If necessary, you may need to remove the expansion slot cover, and you may also need to remove any add-in boards which block access to the PCI slots.

(4) Take the Vantec FireWire PCI Card out of its anti-static bag and push the card into the empty PCI card slot. The card should be mounted with the circuitry and three FireWire connectors facing down. This is the only way to mount the card, so if you are having problems inserting the card into the PCI slot, make sure that it is oriented correctly.

Be sure that the gold contact pins of the PCI card are seated completely inside your computer’s PCI slot. Be aware that it may take some force to get the card fully seated in the slot.

Mac Users

(5) Once the PCI card is seated correctly, tighten with a screw, and, if necessary, replace any add-in boards that you removed in Step 3.

(6) Now you are ready to put the computer’s cover back on and reconnect all of your external peripheral devices and cables.

(7) Power on your computer. After the start up procedure has finished, you should be able to connect devices through the available FireWire ports.

PCI Slots in Apple G3/G4

(10)

Installation 8

4. Installation :

4.2. Driver Installation :

Windows 2000/XP/Vista :

An automated driver installation process will begin upon the detection of the new PCI card and an embedded driver will be loaded. You may be prompted to restart your computer.

Windows 98 :

(1) After the installation of PCI Card. Enter Windows 98 and an “Add New Hardware Wizard” dialog will appear. Click “NEXT”.

( Figure 4.2-A )

(2) Select "Search for the best driver for your device." ( Figure 4.2-B )

(3) Check the box under the search. Press browse, select the X:\UGT-FW100/Driver/win 98 of the CD-ROM and press “NEXT”. X is the path for your CD-ROM drive. Please make sure that your path is set correctly.

( Figure 4.2-C ) PC Users

( Figure 4.2-A )

( Figure 4.2-B )

( Figure 4.2-C )

X:\UGT-FW100/Driver/win 98

(11)

Installation 9

4. Installation :

(4) Find the driver located in the directory within the CD-ROM and press "Next".

( Figure 4.2-D )

(5) After the installation ,click “Next” again, and then “Finish” . ( Figure 4.2-E )

No driver installation is required for Macintosh OS V10.4 and higher. Your Vantec FireWire PCI Card works with the drivers built in to your operating system.

Mac Users

( Figure 4.2-E )

( Figure 4.2-D )

(12)

Warranty / Contact 10

5. Warranty / Contact :

The Fire Wire800/400 comes with a 1 year limited warranty ( 90 day parts ) . If your unit should become defective within that time frame, please go to http://www.vantecusa.com for information on how to receive warranty exchange or repair. Cosmetic defects and missing parts are not covered under this warranty. Please check the contents of the unit to make sure you received all parts. Also, check for any cosmetic flaws. If any parts are missing or if there are cosmetic defects, please contact the retailer from which you purchased the unit immediately and ask for a replacement.

Copyright © 2008 Vantec Thermal Technologies. All Right Reserved.

All Registered Trademarks Belong To Their Respective Companies.

Warranty

Vantec Thermal Technologies

43951 Boscell Rd.

Fremont, CA 94538 tel: 510-668-0368 fax: 510-668-0367

website: www.vantecusa.com

Contact

References

Related documents

4 Remove the Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini PCI Express Card slot compartment cover.. a.Remove or loose the screws that secure the compartment cover

4 Remove the Hard disk drive/Memory/Central processing unit/Mini PCI Express Card slot compartment cover. a.Loosen the screws that secure the

3) Remove the two screws used for the ground connection (see CJ_AF_ INV_010). Electronic Cover Fixing Screw CJ_AF_INV_009 T1 Sensor Ground Screws T2 Sensor CJ_AF_INV_010

Next, undo the 3 screws around the main body cover (shown in yellow) and remove this as well.. With the lens set at the close focus point, note how the 2 stops screws almost

Remove the two screws 1 from the option interface slot cover 2 and remove the slot cover (or network interface card 3 or the serial Interface board).. Figure 2-2-9 Removing the

Thanks to backwards compatibility with USB 2.0 and FireWire 400**, you can literally connect the LaCie 2big Quadra to any standard computer of any era.. Whatever the computer you

To display an individual signal in a given design, select the design in the sim window (such as u_inc shown), right click on a signal in the objects window and specify the "Add

This legal term is also used in place of 'remand', to denote the sending back of an appeal case from the appellate court to the trial court. Res Ipsa Loquitur: A Latin phrase,