Operation Manual
Smart-UPS ™ C
Uninterruptible Power Supply
Tower 1000/1500 VA 120/230 Vac
su0813a
Product Description
The APC™ by Schneider Electric Smart-UPS™ is a high performance uninterruptible power supply (UPS). The UPS provides protection for electronic equipment from utility power blackouts, brownouts, sags, and surges, small utility power fluctuations and large disturbances. The UPS also provides battery backup power for connected equipment until utility power returns to safe levels or the batteries are fully discharged.
This user manual is available on the enclosed Documentation CD and on the APC by Schneider Electric Web site, www.apc.com.
Important Safety Messages
Read the instructions carefully to become familiar with the equipment before trying to install, operate, service or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of this symbol to a Caution product safety label indicates that a hazard exists that can result in injury and product damage if the instructions are not followed.
The following safety messages may appear throughout this manual to warn of potential hazards.
Safety and General Information
Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damage.
Read the Safety Guide supplied with this unit before installing the UPS.
• Adhere to all local and national electrical codes.
• This UPS is intended for indoor use only.
• Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive dust or humidity.
• Be sure the air vents on the UPS are not blocked. Allow adequate space for proper ventilation.
• The battery typically lasts for two to five years. Environmental factors impact battery life. Elevated ambient temperatures, poor quality utility power, and frequent short duration discharges will shorten battery life.
• Connect the UPS power cable directly to a wall outlet. Do not use surge protectors or extension cords.
• The batteries are heavy. Remove the batteries prior to installing the UPS in a rack.
• Refer to “Specifications” on page 2 for UPS and battery weight.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, can result in equipment damage.
Specifications
For additional specifications, refer to the APC by Schneider Electric Web site at www.apc.com.
Weight specifications
UPS + Battery Battery
SMC1000 / SMC1000I 17.24 kg (38 lb)
APCRBC142 5.1 kg (11.2 lb) SMC1500 / SMC1500I
20.41 kg (45 lb)
APCRBC6 7.7 kg (16.9 lb)
Temperature
Operating 0° to 40° C (32° to 104° F) Storage -15° to 45° C (5° to 113° F)
charge UPS battery every six months Maximum
Elevation
Operating 3,000 m (10,000 ft)
Storage 15,000 m (50,000 ft)
Humidity 0% to 95% relative humidity, non-condensing
0° to 40° C (32° to 104° F)
Battery Type Maintenance free, sealed lead acid
Replace used batteries with APC by Schneider Electric approved batteries.
To order a replacement battery go to the APC by Schneider Electric Web site, www.apc.com.
Always recycle used batteries.
For information on recycling a used battery, refer to the Battery Disposal Information sheet included with the replacement battery.
Product Overview
Front panel features
Rear panel features
Installation
For UPS installation information, refer to the Installation Guide for the Smart-UPSC 1000/1500 VA Tower included with the UPS.
The Installation Guide is also available on the Documentation CD included with the UPS and on the APC by Schneider Electric Web site, www.apc.com.
1 Display interface 2 Bezel
3 Battery
4 Internal battery connector cables
120 Vac 230 Vac
1 USB Port 2 Serial data port 3 Battery connector 4 Circuit breaker 5 UPS input 6 Outlets
7 Chassis ground screw
su0453b
su0325d su0325e
Operation
Note:
The UPS will charge to 90% capacity in the first three hours of normal operation.Do not expect full battery runtime capability during this initial charge period.
1. Connect equipment to the UPS.
2. Connect the UPS to a two pole, three wire, grounded source.
Connect equipment to the UPS
CAUTION
RISK OF EQUIPMENT DAMAGE
• Adhere to all local and national electrical codes.
• Wiring should be performed by qualified electrician.
• Always connect the UPS to a grounded outlet.
Failure to follow these instructions can result in equipment damage
USB port: Connect to a computer to use power management software.
Serial port: Connect a serial port cable (not supplied) to use power management software.
Chassis ground screw: Connect the ground leads on transient voltage devices to the chassis ground screw(s), located on the rear panel of the UPS.
su0441b
Configuration mode
Configuration mode provides additional UPS configuration options. Press and hold the MUTE and MENU buttons for two seconds. The UPS will emit a short beep and the two icons will flash to indicate that Configuration mode is enabled.
When Configuration mode is enabled use the MENU button to scroll through the available options. Use the MUTE button to scroll through the settings in each option.
Note:
The UPS will automatically disable Configuration mode after 15 seconds of no activity. To manually disable Configuration mode, press and hold the MUTEandMENUbuttons for two seconds.The UPS will a emit a short beep.
Function Options Description
Self-Test • 0: Default Setting
• 1: Begin Self-Test
0 is the default setting for Configuration mode. Press the MENU button to scroll through the available options.
Press 1 to manually initiate a Self-Test. The UPS will automatically disable Configuration mode.
Note: When the UPS is operating on battery power and Configuration mode is enabled, only the default setting will be available. A manual Self-Test cannot be initiated.
Power Quality
• Good
• Fair
• Poor
Select the input utility power quality tolerance.
• When Good is selected, the unit will go on battery power more often to provide the cleanest power supply to the connected equipment.
• When Fair is selected, the UPS is under normal operating conditions.
• When Poor is selected, the UPS will tolerate more fluctuations in power and will go on battery power less often.
If unsure of the local power quality, select Good.
Output Voltage Setting
230V models only
• 220 Vac
• 230 Vac
• 240 Vac
Select the appropriate voltage for outlets when the UPS is in battery mode.
LCD Display Dimmer
• Load Bar Icon shows 100% = Always On.
• Load Bar Icon shows 0%
= Auto Dim.
When the LCD display dimmer is configured to Auto Dim the LCD will illuminate if a button is pressed or an event occurs. The display will automatically dim after 60 seconds of no activity.
Green Mode Enable
• 0: Disable
• 1: Enable
When Green Mode is enabled the UPS is operating at the most efficient level, bypassing unused AVR components while acceptable utility voltage is present.
The UPS will enter and exit Green mode automatically while enabled.
Clear Event Counter
N/A Press the MUTE button to clear the event counter.
Power saving LCD screen
The display interface can be configured to remain continuously illuminated or to extinguish after a period of inactivity to save electricity.
1. Continuous Illumination Mode: Press and hold the DISPLAY button for two seconds. The display will illuminate and the UPS will beep to confirm Continuous Illumination mode is activated.
2. Power Saving mode: Press and hold the DISPLAY button for two seconds. The display will extinguish and the UPS will beep to confirm Power Saving mode is enabled. While in Power Saving mode, the display will illuminate when a button is pressed. The display will extinguish after 60 seconds of inactivity.
Sensitivity adjustment settings
The UPS detects and reacts to line voltage distortions by transferring to battery backup power to protect connected equipment. In situations where either the UPS or the connected equipment is too sensitive for the input voltage level it is necessary to adjust the transfer voltage.
1. Connect the UPS to a utility power source. Be sure the UPS is turned off.
2. Press and hold thePOWER button for six seconds. The load capacitybar will flash on and off, to indicate the UPS is in Program mode.
3. PressthePOWER button again to scroll through the menu options. The UPS will beep to confirm the selection.
When the UPS is in Sensitivity Configuration mode, the Sensitivity bar graph icons display the sensitivity level setting. See the examples here as a reference.
Low sensitivity Medium sensitivity High sensitivity (Default)
1000/1500 VA 120 Vac: 97-136 Vac 1000/1500 VA 120 Vac: 103-130 Vac 1000/1500 VA 120 Vac: 106-127 Vac 1000/1500 VA 230 Vac: 195-265 Vac 1000/1500 VA 230 Vac: 203-257 Vac 1000/1500 VA 230 Vac: 207-253 Vac Use this setting with equipment
that is less sensitive to fluctuations in voltage or waveform distortions.
Use this setting under normal operating conditions.
Use this setting when connected equipment is sensitive to any minor fluctuations in voltage or waveform distortions.
Status Indicators
Display panel features
LED status indicators
1000/1500 VA 120 Vac 1000/1500 VA 230 Vac
1 On Line/On Battery LED 4 Display interface
2 POWER ON/OFF button 5 DISPLAY button
3 Site Wiring Fault/System Fault LED 6 MUTE button
Note: Refer to “Feature Reference Guide” on page 10 in this manual for a detailed description of the front panel buttons and icons.
Status LED
Audible
Indicator On Audible Indicator Terminates Power On
The UPS is supplying utility power to connected equipment.
The On Line/On Battery LED illuminates green
None N/A
On Battery
The UPS is supplying battery power from the internal battery.
The On Line/On Battery LED illuminates amber
The UPS beeps 4 times every 30 seconds.
The beeping stops when utility power is restored or the MUTE button is pressed for two seconds.
System Fault
The UPS detects an internal system fault.
System Fault LED illuminates red
Constant tone The alarm stops when the POWER ON/ OFF button is pressed for two seconds.
This creates a Fault Reset.
Site Wiring Fault
A building wiring fault has occurred.
Do not operate the UPS. Contact a qualified electrician to correct the building wiring fault.
Site Wiring Fault LED flashes red
None N/A
su0740d su0740c
LCD status indicators
Status LCD Icon Audible Alarms Audible Alarm Terminates
On Battery
The UPS is supplying battery power to the connected equipment.
Beeps 4 times every 30 seconds. The beeping stops when utility power is restored or the UPS is turned off.
Utility Power Overload An overload condition has occurred while the UPS is operating on utility power.
Constant tone The alarm stops when
nonessential equipment is disconnected from the outlets or the UPS is turned off
Battery Power Overload An overload condition has occurred while the UPS is operating on battery power.
Constant tone The alarm stops when
nonessential equipment is disconnected from the outlets or the UPS is turned off.
Low Battery
The UPS is supplying battery power to the connected equipment and the battery is near a total discharge state.
Continuous beeping The beeping stops when utility power is restored or the UPS is turned off.
Battery Fault
The UPS is operating on utility power. The battery does not provide expected backup.
The UPS will beep twice to indicate the battery is disconnected.
The UPS will beep continuously for one minute every five hours to indicate that the battery should be replaced.
Verify that the battery is securely connected.
The battery is nearing the end of its service life and should be replaced.
System Fault
The UPS has experienced an internal fault.
120 Vac models
230 Vac models
N/A Identify the fault message on
the display and refer to System Faults in this manual.
Display interface features
1000/1500 VA120 Vac
1000/1500 VA
230 Vac Description
On Line: The UPS is supplying conditioned utility power to connected equipment.
Green mode: The UPS is operating at the most efficient level, bypassing unused AVR components while acceptable utility voltage is present. The UPS will enter and exit Green mode automatically and will not compromise power protection.
Load Capacity: The load capacity percentage is indicated by the number of load bar sections illuminated. Each bar represents 20% of the load capacity.
Estimated Run Time / Min: This indicates the battery runtime minutes that remain if the UPS switches to battery power.
Battery Charge: The battery charge level is indicated by the number of load bar sections illuminated. When all five blocks are illuminated, the battery is fully charged. Each bar represents 20% of the battery charge capacity.
Overload: The equipment connected to the UPS is drawing more power than the voltage rating allows.
Event: The event counter indicates the number of events that occurred to cause the UPS to switch to battery operation.
Automatic Voltage Regulation (AVR): The UPS has an AVR boost and trim feature that automatically regulates high or low levels of input voltage without using battery power. The UPS also features AVR Bypass which temporarily deactivates the AVR circuitry when the input voltage is within normal range.
This conserves battery power and helps to maximize battery life.
When illuminated, the UPS is compensating for low input voltage.
When illuminated, the UPS is compensating for high input voltage.
In: Input voltage.
Out: Output voltage.
System Fault: An internal system fault has occurred. The fault number will illuminate on the display. Refer to “Display interface features” on page 9.
Mute: An illuminated line through the icon indicates that audible alarms are disabled.
Battery Fault: The icon will flash to indicate that the battery is disconnected.
When the icon remains continuously illuminated the UPS has failed a
Self-Test or the battery is near the end of its service life and should be replaced.
Refer to “LCD status indicators” on page 8.
On Battery: The UPS is supplying battery backup power to the connected equipment.
System Faults
Feature Reference Guide
1000/1500 120 Vac 1000/1500 230 Vac P00 Output Overload
P01 Output Short Circuit P02 Output Over Voltage P04 Unit Over Temperature P06 AVR Relay Fault P13 Inverter Fault
Note: Refer to the “Feature Reference Guide” on page 10 for a detailed description of the front panel buttons and icons.
For more information on System Faults, contact customer support at the APC by Schneider Electric Web site, www.apc.com/support.
Function Button Timing (seconds)
UPS
Status Description
Power
Power On 0.2 Off Press the POWERON/OFFbutton to turn on the UPS.
The UPS will operate on utility power.
If utility power is not available the UPS will operate on battery power.
Power Off 2 On Press the POWERON/OFFbutton to turn off the UPS.
Display
Status Inquiry 0.2 On Press to verify the status or condition of the UPS. The LCD will illuminate for 60 seconds.
Power Saving mode Continuous Illumination
2 On The LCD will illuminate and the UPS will beep to confirm Continuous Illumination mode is activated.
The LCD will extinguish and the UPS will beep to confirm that
Power Saving mode is activated. While in Power Saving mode, the LCD will illuminate if a button is pressed or an event occurs, then extinguish after 60 seconds of no activity.
Mute
Event Specific 0.2 On Disable any audible alarms caused by an event.
Enable/Disable 2 On Enable or disable the audible alarms. The Mute icon will illuminate and the UPS will beep once.
Sensitivity 6 Off The Load Capacity icon will flash to indicate the UPS is in Program mode. Use thePOWERON/OFFbutton to scroll through and select Low, Medium, and High sensitivity levels. The UPS will beep to confirm the selection. Refer to “Sensitivity adjustment settings” on page 6 in this manual.
su0752a su0752b
Troubleshooting
Problem and Possible Cause Solution The UPS will not turn on or there is no output
The UPS has not been turned on. Press the ON button once to turn on the UPS.
The UPS is not connected to utility power. Be sure the power cable is securely connected to the UPS and to the utility power supply.
The input circuit breaker has tripped. Disconnect nonessential equipment and reset the circuit breaker.
The UPS shows very low or no input voltage. Check the utility power supply to the UPS by plugging in a table lamp. If the light is very dim, check the utility voltage.
The battery is not securely connected. Be sure that all battery connections are secure.
There is an internal UPS fault. Do not attempt to use the UPS. Unplug the UPS and have it serviced immediately.
The UPS is operating on battery while connected to utility power
The input circuit breaker has tripped. Disconnect nonessential equipment and reset the circuit breaker.
There is very high, very low, or distorted input line voltage.
Move the UPS to a different outlet on a different circuit. Test the input voltage with the utility voltage display. If acceptable to the connected equipment, reduce the UPS sensitivity.
The
UPS is beeping
The UPS is operating normally. None. The UPS is protecting the connected equipment.
The
UPS does not provide expected battery backup time
The UPS battery is weak due to arecent power outage or is near the end of its service life.
Charge the battery. Batteries require recharging after an extended outage.
Elevated ambient temperatures, poor quality utility power, and frequent short duration discharges will shorten battery life.
If the battery is near the end of its service life, consider replacing the battery even if the replace battery icon is not illuminated.
The UPS is experiencing an overload condition.
Check the UPS load display. Unplug nonessential equipment, such as printers.
The Fault LED is illuminated, the UPS displays a fault message and emits a constant beeping
Internal UPS fault. Do not attempt to use the UPS. Turn the UPS off and have it servicedimmediately. If more than one fault is present the fault messages will be displayed alternately on the display screen.
The Replace Battery icon is illuminated
The battery has a weak charge. Allow the battery to recharge for at least four hours. Then, perform a Self-Test. If the problem persists after recharging, replace the battery.
The replacement battery is not properly connected.
Be sure the battery connector is securely connected.
Site Wiring Fault LED is flashing
Wiring faults detected include If the UPS indicates a site wiring fault, have a qualified electrician inspect the
Service and Transport
If the unit requires service, do not return it to the dealer. Follow these steps:
1. Review the Troubleshooting section of the manual to eliminate common problems.
2. If the problem persists, contact APC by Schneider Electric Customer Support through the APC by Schneider Electric Web site, www.apc.com.
a. Note the model number and serial number and the date of purchase. The model and serial numbers are located on the rear panel of the unit and are available through the LCD display on select models.
b. Call APC by Schneider Electric Customer Support and a technician will attempt to solve the problem over the phone. If this is not possible, the technician will issue a Returned Material Authorization Number (RMA#).
c. If the unit is under warranty, the repairs are free.
d. Service procedures and returns may vary internationally. Refer to the APC by Schneider Electric Web site for country specific instructions.
3. Pack the unit in the original packaging whenever possible to avoid damage in transit. Never use foam beads for packaging. Damage sustained in transit is not covered under warranty.
a. Always DISCONNECT THE UPS BATTERIES before shipping. The United States Department of Transportation (DOT), and the International Air Transport
Association (IATA) regulations require that UPS batteries be disconnected before shipping. The internal batteries may remain in the UPS.
b. External Battery Pack products are deenergized when disconnected from the associated UPS product. It is not necessary to disconnect the internal batteries for shipping. Not all units utilize an external battery pack.
4. Write the RMA# provided by Customer Support on the outside of the package.
5. Return the unit by insured, prepaid carrier to the address provided by Customer Support.
Transport the unit
1. Shut down and disconnect all connected equipment.
2. Disconnect the unit from utility power.
3. Disconnect all internal and external batteries (if applicable).
4. Follow the shipping instructions outlined in the Service section of this manual.
Two Year Limited Factory Warranty
This warranty applies only to the products you purchase for your use in accordance with this manual.
Terms of warranty
Schneider Electric IT (SEIT) warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. SEIT will repair or replace defective products covered by this warranty. This warranty does not apply to equipment that has been damaged by accident, negligence or misapplication or has been altered or modified in any way.
Repair or replacement of a defective product or part thereof does not extend the original warranty period. Any parts furnished under this warranty may be new or factory remanufactured. For country specific warranty information, refer to the APC by Schneider Electric Web site at www.apc.com.
Non-transferable warranty
This warranty extends only to the original purchaser who must have properly registered the product. The product may be registered at the APC by Schneider Electric Web site, www.apc.com.
Exclusions
SEIT shall not be liable under the warranty if its testing and examination disclose that the alleged defect in the product does not exist or was caused by end user’s or any third person’s misuse, negligence, improper installation or testing. Further, SEIT shall not be liable under the warranty for unauthorized attempts to repair or modify wrong or inadequate electrical voltage or connection, inappropriate on site operation conditions, corrosive atmosphere, repair, installation, exposure to the elements, Acts of God, fire, theft, or installation contrary to SEIT recommendations or specifications or in any event if the SEIT serial number has been altered, defaced, or removed, or any other cause beyond the range of the intended use.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR OTHERWISE, OF PRODUCTS SOLD, SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION
HEREWITH. SEIT DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY, SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE. SEIT EXPRESS WARRANTIES WILL NOT BE ENLARGED, DIMINISHED, OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE OUT OF, SEIT RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION WITH THE PRODUCTS.
THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES. THE WARRANTIES SET FORTH ABOVE CONSTITUTE SEIT’S SOLE LIABILITY AND PURCHASER’S EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES. SEIT WARRANTIES EXTEND ONLY TO PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES.
IN NO EVENT SHALL SEIT, ITS OFFICERS, DIRECTORS, AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY FORM OF INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, ARISING OUT OF THE USE, SERVICE OR INSTALLATION, OF THE PRODUCTS, WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF FAULT, NEGLIGENCE OR STRICT LIABILITY OR WHETHER SEIT HAS BEEN ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES. SPECIFICALLY, SEIT IS NOT LIABLE FOR ANY COSTS, SUCH AS LOST PROFITS OR REVENUE, LOSS OF EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF SUBSTITUENTS, CLAIMS BY THIRD PARTIES, OR OTHERWISE.
NO SALESMAN, EMPLOYEE OR AGENT OF SEIT IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY. WARRANTY TERMS MAY BE MODIFIED, IF AT ALL, ONLY IN WRITING SIGNED BY AN SEIT OFFICER AND LEGAL DEPARTMENT.
Warranty claims
Customers with warranty claims issues may access the SEIT customer support network through the Support page of the APC by Schneider Electric Web site, www.apc.com/support. Select your country from the country selection drop down menu at the top
APC by Schneider Electric Worldwide Customer Support
Customer support for this or any other APC by Schneider Electric product is available at no charge in any of the following ways:
• Visit the APC by Schneider Electric Web site to access documents in the APC by Schneider Electric Knowledge Base and to submit customer support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC by Schneider Electric Web sites for specific countries, each of which provides customer support information.
– www.apc.com/support/
Global support searching APC by Schneider Electric Knowledge Base and using e-support.
• Contact the APC by Schneider Electric Customer Support Center by telephone or e-mail.
– Local, country-specific centers: go to www.apc.com/support/contact for contact information.
– For information on how to obtain local customer support, contact the APC by Schneider Electric representative or other distributors from whom you purchased your APC by Schneider Electric product.
Select models are ENERGY STAR® qualified.
