ac9400[1].pdf

(1)

Time & Attendance /

Access Control

User's Manual

(2)

Information

Technical And Operational Description

Connection Of Multiple Units

Connections

...

1

4

5

16

27 ...

...

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communication.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

30 ...

Specifications

31 ...

Communication Protocol

...

33 Introduction

Installation

(3)

AC9400 Access Control

AC-9400

( Main Unit only )

AC-9400A

(With 2nd Reader : PCR943A-01) metal-wall mounting possible

MACHINE TYPE

FUNCTION

AC-9400B

(With 2nd Reader : PCR943-01) metal-wall mounting possible

AC-9400C

(With 2nd Reader : GP30W-01)

OPTIONAL

GNET VER 1.2 RS- 485 255 RTC RS-232 RFID BEEP TEST AUTO PASSBACKANTI READER EXT KEYPAD& 8096 USER CARD 80 ZONE TABLE 32 SENSOR TABLE 28336 REC QUEUE GNET VER 1.2 RS- 485 255 RTC RS-232 RFID BEEP TEST AUTO PASSBACKANTI READER EXT 8096 USER CARD 80 ZONE TABLE 32 SENSOR TABLE 28336 REC QUEUE GNET VER 1.2 RS- 485 255 RTC RS-232 RFID BEEP TEST AUTO PASSBACKANTI 8096 USER CARD 80 ZONE TABLE 32 SENSOR TABLE 28336 REC QUEUE GNET VER 1.2 RS- 485 255 RTC RS-232 RFID BEEP TEST AUTO PASSBACKANTI 8096 USER CARD 80 ZONE TABLE 32 SENSOR TABLE 28336 REC QUEUE READER EXT

(4)

Standard Package

User's Manual Access Control AC-9400 Series AC-9400 Series AC-9400 Series AC-9400 Series M95-5034

Wall-mounting screw Kit ( ASY-M93-1049-18 ) User's Manual ( M95-5032 ) Software Disk ( DISK5078 ) RS-232 Cable ( WAS-1436 )

Wire for External Sensor /Lock/Alarm ( WAS-1466 )

Main unit (AC-9400 )

Power Adaptor DC12V/120VAC ( APR-1014 ) or DC12V/230VAC ( APR-1015A )

Screw Mounting Template ( M92-5016 )

Cable for External Reader or Push button ( Egress Switch )

( WAS-1465 )

NO:123411 NO:123412

Test Card ( M95-5026 )

(5)

Optional

RS-485/RS-232 Converter ( CON485 ) RS-485 Cable ( WAS-1467 )

Order Information

A C 9 4 0 0

- 0 0

With 120VAC Adaptor U

E With 230VAC Adaptor

No Power Adaptor With 2nd Reader PCR943A-01

A B C With 2nd Reader PCR943-01 With 2nd Reader GP30W-01 No 2nd Reader

25P Male / 9P Female RS232 Connector (CN5-1049)

Cable For Multiple Connect ( WAS-1432 )

(6)

AC-9400 is a highly flexible time & attendance / access control terminal. It may control the electric lock by using the RFID card. It offers reliable and future-oriented time & attendance / access control solution to meet most requirements in most areas. It can be used either as an off-line stand-alone access control unit or as an on-line access control terminal through RS-485 or RS232 interface. The major features of Model AC9400 are:

Can be used either as an off-line stand-alone unit or as an on-line terminal. 4 character LED to display message, and clock time.

Use proximity Card

Provides RS-232 communication interfaces for remote command programming and data collection. RS-485 interface is optional.

The number of user's card can be from 000000 to FFFFFF,but maximum 8096 user's card.

Contain 512 K bytes Flash Memory buffer, store up to 28,336 records .

Provide a connection for indoor egress switch or one button on keypad to open the door lock from inside the room. But there is no 2nd reader when egress switch is connected.

Door lock open period is programmable from 1 to 255 seconds.

Built-in Real-Time Clock (RTC) module.

Use non-volatile memory, the memory will never lose when power failure.

Personal ID number (PIN) can be from 0 to 9, 00 to 99, 000 to 999, 0000 to 9999, 00000 to 99999, 000000 to 999999.

Two external drives : Drive 1 for door lock, Drive 2 for alarm.

Provide a connection for door sensor to detect the door security. Provide a connection for external second card reader.

Provide a 7x2 keypad to enter the PIN or to program the unit.

Door open mode can be set as " read card only" or "press keypad only" or "read card plus press keypad".

Provide two serial port connectors for daisy-chain connection of multi-unit applications, up to 255 units.

Provide RS-232 communication interface. RS-485 version for long-distance connection is also available.

Alarm active period is programmable from 1 to 65535 seconds. Allows 80 time table for Access control Time zone.

Allows 32 time table for Sensor active Time zone.

Use PC to set Master System Code / Machine ID / User's Card / User Time Zone / Sensor Time Zone / Door Open Duration / Clock Time / Anti-passback ON or OFF / Sensor detect ON or OFF / Baudrate...etc.

Can use keypad to display Firmware Version / Machine ID / Records Number / User's Card Number / Year / Month and Date / Machine Status.

(7)

Front Panel

1

2

3

1 2 3

DISPLAY WINDOW

CARD READER

KEYPAD

The display can show Time,Week Day,Status of card reading and some other messages.

Approach the card here to read

To enter the PIN or to program the unit or to set some messages.

(8)

1 2 3 4 5

HOST JACK

NEXT JACK

EXT. RDR JACK

ALARM JACK

LOCK JACK

For connection to the host computer or the preceding AC9400 access control unit.

For connection to the next AC9400 access control unit.

For connection to the external second reader when the AC9400 main unit is installed inside or connection to the egress switch when the AC9400 main unit is installed outside

For connection to the external alarm.

For connection to the external lock.(electric strike)

6

SENSOR JACK

For connection to the external door sensor.

Rear Panel

1

2

3

4

5

6

7

POWER JACK

(9)

READY

ERROR

SUN MON TUE WED THU FRI SAT

5

2

1

3

4

1 2 3 4 5

TIME OR MESSAGE DISPLAY

WEEK DAY DISPLAY

READY

ERROR

STATUS INDICATOR

It display clock time at normal use. It will display some message when reading a card or entering PIN pad or setting parameters.

It displays week day at normal use.It will display some meaning when setting parameters.

It means the machine is ready for use.

It means reading a card with error or entering PIN pad with error

It shows the communication status with PC. It will blink when communication is going and message is sending.

(10)

1

HOST: connect to PC or from the former unit

Connectors on back cover

1

4

6

3

7

5

2

CTS 1 2 3 PIN 4 5 6 7 8 FUNCTION TXD RTS RXD RS485+ SG RS485-NC HOST CTS 1 2 3 PIN 4 5 6 7 8 FUNCTION TXD RTS RXD RS485+ SG RS485-NC RS-232 CTS 1 2 3 PIN 4 5 6 7 8 FUNCTION TXD RTS RXD RS485+ SG RS485-NC RS-485 1 2 3 4 5 6 7 8 NC RS485-SG RS485+ TXD CTS RXD RTS PIN FUNCTION NEXT 1 2 3 4 5 6 7 8 NC RS485-SG RS485+ TXD CTS RXD RTS PIN FUNCTION RS-232 1 2 3 4 5 6 7 8 NC RS485-SG RS485+ TXD CTS RXD RTS PIN FUNCTION RS-485

(11)

PIN NO 1 COM 2 NC 3 DC 12V 10% / 500mA NO : COM : NC : 1 2 3 4 5 6 PIN FUNCTION ALARM Normal Open Common Normal Close

3

EXT.RDR : Connect External 2nd Reader or door open

push button(Egress switch)

4

ALARM : Dry contact relay connector for external alarm

7

DC12V : Power supply connector

NO 1 COM 2 NC 3 NO : COM : NC : PIN FUNCTION LOCK Normal Open Common Normal Close

5

LOCK : Dry contact relay connector for electric strike

GND 1 SEN 2 12V 3 GND : SEN : VCC : PIN FUNCTION SENSOR Ground Sensor Input

Power Output ( Direct Connect Power )

6

SENSOR : Dry contact relay connector for door sensor

VCC * VCC * D1 D0 GND GND FUNCTION EXT. RDR

* Direct Connect Power Input DC12V

PIN 1 2 3 4 5 6 VCC VCC PB * PB * GND GND FUNCTION

EXT. PUSH BUTTOM

(12)

1. Keypad Operation at "READY" standby mode

F1 F1F1

F1

_****

PPPP PPPP PPPP PPPP

1-2. Enter Message Displaying mode

1-3. Enter PIN number to open door 1-1. Enter Parameter Setting mode

Key

Exp. _{You must enter Setting mode when you want to change the Master PIN}

or the Machine Address number or some parameters.

ENT ENT ENT ENT

Symbol PPPP PPPP PPPP PPPP Master PIN number of the unit (Default :0000 )

F2 F2 F2 F2

You must enter Message Displaying mode when you want to see some Message, Such as Firmware Version, Machine Address, Summary of the Registered card, Summary of the Records, Year, Date (Month/ Day), Baud rate, Door Sensor ON/OFF, Lock ON/OFF, Anti-Passback ON/OFF etc. None ENT ENTENT ENT X X X X XXXX XXXX XXXX XXXX XXXX

Can be any number but maximum 6 digits.

ENT ENT ENT ENT X X X

X XXXX XXXX XXXX XXXX XXXX _{Registered PIN number}

KEYPAD OPERATION

F1 F1 F1 F1

_****

PPPP PPPP PPPP PPPP 1-4. Relieve Alarm

This is the same operation as (1-1) Paragraph,but it will relieve the alarm when the alarm is activating. It would enter Setting mode when the Machine is at normal " READY" standby mode.

ENT ENT ENT ENT P PP

P PPPP PPPP PPPP Master PIN number of the unit (Default :0000 )

Key Exp. Symbol Key Exp. Symbol Key Exp. Symbol

(13)

2. Keypad Operation at Parameter Setting Mode

0 00

0

_****

PPPP PPPP PPPP PPPP

2-1. Change Master PIN number of the unit

Change Master PIN number of the unit.

ENT ENT ENT ENT P PP

P PPPP PPPP PPPP New Master PIN number you want.

1 11

1

_****

AAAA AAAA AAAA

2-2. Change Machine Address number

1 Machine Address number (Machine ID) Factory Default is 000

2.There are many AC9400 units connected in one network,you have to set every unit with a different Machine Address number before

connected to the network. Also the Machine Address number for each unit must not be 000 .

ENT ENT ENT ENT A A A A AAAA AAAA

****

2-3. Back to "READY" Standby Mode from Setting Mode

1. The unit will go back to "READY" Standby Mode from Setting Mode. 2. If there is no keypad pressed or no card reading in 15 seconds, the machine will go back to " READY" standby Mode automatically.

ENT ENT ENT ENT

****

1-5. One key to open door

When the AC9400 main unit is installed inside the room and with the external 2nd reader installed outside and you would push one key (one button) to open door from inside, instead of reading a card, you may set the AC9400 one-key-to-open-door function to be enabled. You can press one key to open the door when the one-key-to-open-door function is enabled. ENT ENT ENT ENT None ENT ENTENT ENT

New Machine Address number you want.

Key Exp. Symbol Key Exp. Symbol Key Exp. Symbol Key Exp. Symbol None

(14)

3. Keypad Operation at Message Displaying Mode

ENT

ENTENT ENT Firmware

Version MachineAddress ENTENTENTENT Registered cardsSum of the ENTENTENTENT Sum of therecords

ENT ENTENT

ENT Year _ENT_ENT_ENT_ENT Date ENTENTENTENT _ParametersOther ENTENTENTENT

The 4-digit display will show the Firmware Version of the unit. Display [1.0r0] : <1.0> Firmware Version, <r0> Revised Number. The 4-digit display will show the Machine Address of the unit.

Display [A000] : <A> Display Address function , <000> Machine Address The 4-digit display will show the Summary number of the Registered Cards. Display [0000] : <0000> Total number of the Registered Cards

The 4-digit display will show the Summary number of the Records. Display [0000] : <0000> Total number of the Records

The 4-digit display will show the existing Year of the unit. Display [2000] : <2000> Existing Year of the Machine

The 4-digit display will show some other parameters.

Display [-L-2] : 1st <-> No sensor function, 2nd <L> Lock will activate when reading a card or pressing keypad, 3th <-> No Anti-passback function, 4th <2> Baudrate 9600 BPS.

The 4-digit display will show the existing Date of the unit. Display [0612] : <06> Month, <12> Day

1.If there is no card reading or no keypad pressing in 5 seconds at Message Displaying Mode,the Machine will go back to "READY" Standby Mode automatically.

ITEM 1 2 3 4 DISPLAY DIGITAL X.X r Y A XXX XXXX XXXX XXXX XX YY X Y Z P DEC. ASCII DEC. DEC. DEC. DEC. DEC. 0(2400BPS)/1(4800BPS)/2(9600BPS)/3(19200BPS) COMMENT Firmware Version [X.X]: 1.0 ~ 9.9 Revised number [Y]: 0 ~ 9 Machine Address [XXX]: 000 ~ 255

Sum of the Registered cards [XXXX]: 0000 ~ 8096 Sum of the records [XXXX]: 0000 ~ 9999

Year [XXXX]: 2000 ~ 2100

Month [XX]: 01 ~ 12 / Day [YY]: 01 ~ 31

2.The operation of the Message Displaying Mode,some parameters is as below : LED SUN SAT MON TUE WED THU FRI Firmware Version Machine Address Sum of the Registered cards Sum of the records Year Date Other Parameters Firmware Version Machine Address Sum of the Registered cards Sum of the records Year Date Other Parameters Disable -Enable S L A ITEM Sensor Detect Lock Anti-passback Baud Rate X Y Z P Key Exp. Symbol

(15)

Status and Control Displaying

READY ERROR

F1 _*_**_* PPPP PPPP PPPP PPPP ENT

READY ERROR

Setting Mode

0 _*_**_* PPPP PPPP PPPP PPPP ENT

Change Master PIN

1 11

1 **** 1111 2222 3333 ENT

Change Machine Address

* ** * ENT

Back to Standy Mode

* ** * ENT One-key-to-open READY ERROR

SUN MON TUE WED THU FRI SAT READY

ERROR

F1 _*_**_* PPPP PPPP PPPP PPPP ENT Relieve Alarm X XX X XXXX XXXX ENT Enter PIN READY ERROR

ENT

Message Displaying Mode

F2 Message Displaying Mode "READY" Standby Mode ERROR OPEN DOOR ALARMING PROGRAMMING STANDBY ADDRESS=123 PASSWORD

(16)

READY ERROR

ENT Keypad Message Displaying Mode READY ERROR

NUMBER OF RECORDS = 0109 FIRMWARE VERSION : 1.0R0

MACHINE ID : 123

NUMBER OF USER CARD = 0010

ENT Keypad ENT Keypad ENT Keypad ENT Keypad ENT Keypad ENT Keypad READY ERROR

YEAR = 2000

READY ERROR

DATE: 10/20

READY ERROR

ANTI-PASSBACK : OFF LOCK ACTIVE : ON SENSOR DETECT : ON BAUDRATE : 9600 BPS

(17)

READY ERROR

READ CARD ONLY

READY ERROR

KEYPAD ONLY _{PLUS KEYPAD}READ CARD

NO:123412 NO:123412 OK ERROR OK ERROR READY ERROR

ERROR CODE

A B B 1 2 3 4 5 6 7 8 9

Card ID not exist Time zone not fit Anti-passback error

Open (Out) / Anti-passback Open (Entry) / Anti-passback Anti-passback buffer is full. Not input password

Input password is error Open A 1 2 Internal Reader External Reader

ERROR CODE TABLE

9 Internal Keypad A External Keypad

INPUT ID

OPEN ER__

(18)

-PC

CONNECT TO PC

RS-485 INTERFACE

RS-485

RS-232 INTERFACE

RS-232 PC PC

CONNECT

WAS-1436 AC-9400 AC-9400 WAS-1467 CON-485 CN5-1049 AC-9400 RS-232/RS-485 Converter

(19)

BLACK ORANGE GRAY COLOR YELLOW GREEN RED RJ-11 8P8C PIN 1 2 3 4 5 6 DB 9P FEMALE PIN 7 2 8 3 NC * 5

CABLE

RS-232 INTERFACE

RS-232

RS-485 INTERFACE

RS-485 BROWN BLUE 7 8 NC * NC * RJ-11 8P8C PIN 1 2 3 4 5 6 WIRE CUT* CUT* CUT* CUT* 5 CUT* 7 8 7 CUT* * NC - No Connect WAS-1436 WAS-1467 BLACK ORANGE GRAY COLOR YELLOW GREEN RED BROWN BLUE PIN1 PIN8 PIN1 PIN8 PIN7 PIN5

WAS-1436 : LENGH - 2000 mm , WIRE - 8P8C / AWG #28

(20)

INTERFACE

RS-232 INTERFACE

RS-232

RS-485 INTERFACE

RS-485 PC CTS 1 2 3 PIN 4 5 6 7 8 FUNCTION TXD RTS RXD RS485+ SG RS485-NC HOST CTS 1 2 3 PIN 4 5 6 7 8 FUNCTION TXD RTS RXD RS485+ SG RS485-NC HOST PC VCC 1 2 3 PIN 4 FUNCTION GND RS485-RS485+ CON485 WAS-1436 PLUG 1 2 3 4 5 6 7 8 BLACK ORANGE GRAY COLOR YELLOW GREEN RED BROWN BLUE DB9 7 2 8 3 NC 5 NC NC DCD 1 2 3 PIN 4 5 6 7 8 FUNCTION RXD TXD DTR SG DSR RTS CTS PC RS232 9 RI WAS-1467 BLACK ORANGE GRAY COLOR YELLOW GREEN RED BROWN BLUE PLUG 1 2 3 4 5 6 7 8 WIRE CUT* CUT* CUT* CUT* 5 CUT* 7 CUT* RS-232/RS-485 Converter CON485

(21)

CONNECT TO EXTERNAL READER

PCR-943A-01 / PCR-943-01

GP30W-01

AC-9400 AC-9400 GP30W PCR-943A-01 PCR-943-01 RED BLACK GREEN WHITE YELLOW WHITE BLUE GREEN BLACK RED YELLOW BLUE BROWN ORANGE ( NOT CONNECT )

CONNECT

WAS-1465

(22)

PCR-943A-01 / PCR-943-01

GP30W-01

GP30W-01 PCR-943A-01 PCR-943-01 RED BLACK GREEN WHITE YELLOW BLUE BROWN ORANGE RED 1 2 3 PIN 4 5 6 COLOR BROWN GREEN WHITE YELLOW BLACK PIN 1 PIN 6 POWER FUNCTION POWER D1 D0 GND GND Power DC5 - 13.5V FUNCTION Power Ground Clock/D1 Data/RS232/D0 CP Program Input Ext. Buzzer Ext Led RED COLOR BLACK WHITE GREEN ORANGE YELLOW BLUE BROWN 1 2 3 PIN 4 5 6 BLUE COLOR YELLOW GREEN RED BLACK WHITE BLUE YELLOW GREEN RED BLACK WHITE

* YELLOW Connect to WHITE for Wiegand Interface

PIN 1 PIN 6

CABLE

PCR-943A-01 / PCR-943-01

WAS-1465 GP30W

(23)

PCR-943A-01 / PCR-943-01

GP30W-01

PCR-943A-01 PCR-943-01 PIN 1 PIN 6 POWER FUNCTION POWER D1 D0 GND GND RED COLOR BROWN GREEN WHITE YELLOW BLACK 1 2 3 PIN 4 5 6 1 2 3 PIN 4 5 6 POWER FUNCTION POWER D1 D0 GND GND EXT. RDR PCR-943A-01 / PCR-943-01 GP30W-01 1 2 3 PIN 4 5 6 BLUE COLOR YELLOW GREEN RED BLACK WHITE RED COLOR BLACK WHITE GREEN ORANGE YELLOW BLUE VCC FUNCTION GND CLOCK/D1 DATA/RS232/D0 CP PROGRAM BUZZER 1 2 3 PIN 4 5 6 POWER FUNCTION POWER D1 D0 GND GND EXT. RDR WAS-1465 GP30W-01 PIN 6 PIN 1

INTERFACE

(24)

CONNECT TO EXTERNAL PUSH BUTTOM

AC-9400 PUSH BUTTOM

WHITE BLUE GREEN BLACK RED YELLOW ( NO CONNECT) PIN 6 PIN 1

CONNECT

CABLE

INTERFACE

1 2 3 PIN 4 5 6 POWER FUNCTION POWER D1 D0 GND GND EXT. RDR 1 2 3 PIN 4 5 6 BLUE COLOR YELLOW GREEN RED BLACK WHITE WAS-1465 PUSH BUTTOM PUSH BUTTOM

LOOK " CONNECT TO EXTERNAL READER " PAGE

( EGRESS SWITCH )

(25)

CONNECT TO EXTERNAL READER + PUSH BUTTOM

AC-9400 PUSH BUTTOM

WHITE (+) BLUE GREEN ( D0 ) BLACK RED ( D1 ) YELLOW ( - ) PIN 6 PIN 1

CONNECT

CABLE

INTERFACE

1 2 3 PIN 4 5 6 POWER FUNCTION POWER D1 D0 GND GND EXT. RDR 1 2 3 PIN 4 5 6 BLUE COLOR YELLOW GREEN RED BLACK WHITE WAS-1465 PUSH BUTTOM PUSH BUTTOM

LOOK " CONNECT TO EXTERNAL READER " PAGE

( EGRESS SWITCH ) WAS-1465

CONNECT TO EXTERNAL READER

1N5819 * 1N5819 * 1N5819 X 2 * CONNECT TO EXTERNAL READER

+

CONNECT TO EXTERNAL READER

Yellow/Black White Green Red/Brown

(26)

CONNECT TO EXTERNAL ALARM

AC-9400 ALARM WHITE BLACK RED

CONNECT

CABLE

INTERFACE

1 2 3 PIN NO FUNCTION COM NC ALARM 1 2 3 PIN COLOR WAS-1466 ALARM ALARM ALARM POWER 1 2 3 PIN WAS-1466 COLOR RED BLACK WHITE RED BLACK WHITE PIN1

(27)

CONNECT TO EXTERNAL LOCK

AC-9400 LOCK WHITE BLACK RED

CONNECT

CABLE

INTERFACE

1 PIN NO FUNCTION LOCK 1 PIN COLOR WAS-1466 LOCK LOCK LOCK POWER 1 2 3 PIN WAS-1466 COLOR RED BLACK WHITE RED

(28)

CONNECT TO EXTERNAL SENSOR

AC-9400 SENSOR WHITE BLACK RED

CONNECT

CABLE

INTERFACE

1 2 3 PIN GND FUNCTION SEN. 12V SENSOR 1 2 3 PIN COLOR WAS-1466 SENSOR SENSOR 1 2 3 PIN WAS-1466 COLOR RED BLACK WHITE DOOR RED BLACK WHITE

(29)

CONNECT TO POWER

AC-9400

CONNECT

INTERFACE

1 2 PIN DC 12V POWER ADAPTOR 1 2 PIN DC 12V 1 2 3 PIN SENSOR 1 2 3 PIN 4 5 6 EXT. RDR

Power Adaptor DC12V/120VAC ( APR-1014A ) or DC12V/230VAC ( APR-1015A ) I N I N I N I N OUT OUT OUT OUT FUNCTION_GND SEN. 12V POWER FUNCTION POWER D1 D0 GND GND 12 V FUNCTION GND 12V FUNCTION GND Power Adaptor

(30)

PIN1 PIN8

WAS-1432 : LENGTH - 1000 mm , WIRE - 8P8C / AWG #28

BLACK ORANGE GRAY COLOR YELLOW GREEN RED 8P8C PIN 1 2 3 4 5 6 8P8C PIN 8 7 6 5 4 3 BROWN BLUE 7 8 2 1 WAS-1432

CABLE

PIN1 PIN8 PC

CONNECTION OF MULTIPLE UNITS TO PC

(31)

RS-232 INTERFACE

RS-232

CONNECT

PC WAS-1436 PLUG 1 2 3 4 5 6 7 8 RS232 HOST AC9400 #1 WAS-1432 PLUG 8 7 6 5 4 3 2 1 PLUG 1 2 3 4 5 6 7 8 PC WAS-1436 AC-9400 #1 AC-9400 #3 AC-9400 #2 NEXT AC9400 WAS-1432 WAS-1432 WAS-1432 1 2 3 4 5 6 7 8 9 DCD RXD TXD DTR SG DSR RTS CTS RI 1 2 3 4 5 6 7 8 CTS TXD RTS RXD RS485+ SG RS485-NC NEXT 1 2 3 4 5 6 7 8 NC RS485-SG RS485+ TXD CTS RXD RTS 7 2 8 3 NC 5 NC NC DB9 HOST AC9400 #2 1 2 3 4 5 6 CTS TXD RTS RXD RS485+ SG NEXT WAS-1432 PLUG 8 7 6 5 4 3 PLUG 1 2 3 4 5 6 HOST AC9400 #3 1 2 3 4 5 6 CTS TXD RTS RXD RS485+ SG NEXT NC Up to 31 units 1 2 3 4 5 6 NC RS485-SG RS485+ TXD CTS 1 2 3 4 5 6 NC RS485-SG RS485+ TXD CTS

(32)

RS-485 INTERFACE

RS-485 CON485 WAS-1467 PLUG 1 2 3 4 5 6 7 8 RS232 HOST AC9400 #1 WAS-1432 PLUG 8 7 6 5 4 3 2 1 PLUG 1 2 3 4 5 6 7 8 2 4 1 3 GND RS485+ VCC RS485-1 2 3 4 5 6 7 8 CTS TXD RTS RXD RS485+ SG RS485-NC NEXT CUT CUT CUT CUT 5 CUT 7 CUT WIRE HOST AC9400 #2 1 2 3 4 5 6 7 8 CTS TXD RTS RXD RS485+ SG RS485-NC NEXT WAS-1432

PLUG PLUG HOST

AC9400 #3 1 2 3 4 5 6 7 8 CTS TXD RTS RXD RS485+ SG RS485-NC NEXT CN5-1049 PC AC-9400 #1 AC-9400 #3 AC-9400 #2 NEXT AC9400 WAS-1432 WAS-1432 WAS-1432 WAS-1467 CON485 Up to 255 units 1 2 3 4 5 6 7 8 NC RS485-SG RS485+ TXD CTS RXD RTS 1 2 3 4 5 6 7 8 NC RS485-SG RS485+ TXD CTS RXD RTS 1 2 3 4 5 6 7 8 NC RS485-SG RS485+ TXD CTS RXD RTS 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 RS-232/RS-485 Converter

(33)

RS232 Interface : Power Supply : Dimensions : Mounting : Environment : RS232 , Half-Duplex , 8N1 , 9600 bps AC DC _{DC 12V, 500mA} D 52 x W 192 x H 120 mm % C/F

Operating Temp : 0 ~ 55 C for AC9400 main unit -10 ~ 60 C for external readers Storage Temp : -10 ~ 55 C

Humidity : 10 ~ 90 % relative RS-232

GNET

VER 1.2

Memory Size for Storing Data : Communication Protocol :

GIGA-TMS Net Version 1.2 (GNET V1.2) RTC

RFID

RS-485 RS485 Interface :

RS485 , Half-Duplex , 8N1 , 9600 bps

CLOCK :

Relay Contact Capacity for ALARM And LOCK :

6A / AC 250V , 12A / DC 28VDC

RFID Proximity Card :

125 KHZ , ASK , 64 Bits , Manchester Coding

CMOS SuperFlash R*_{EEPROM 512K bytes}

READER

EXT

KEYPAD& EXTERNAL RFID READER ( 2nd Reader ):

125 KHZ , ASK , 64 Bits , Manchester Coding Wiegand Interface PCR943A-01: RFID Reader with keypad,Read range 5 ~10 cm,

Metallic wall workable, Temp. -10 ~ 60 C

Real Time Clock (RTC) module with built-in 10 year battery Clock accuracy is better than 1 minute per month at 25 C for the period of time-keeping time

Up to 1200 meters / Up to 255 Units on the bus

Electrically Life - 10 x 10 operations. Min.4

Wall-mounting

PCR943-01: RFID Reader without keypad,Read range 5 ~10 cm, Metallic wall workable, Temp. -10 ~ 60 C

GP30W-01: RFID Reader without keypad,Read range 15 ~30 cm for non-metallic wall mounting, Temp. -10 ~ 60 C

Up to 15 meters / Up to 31 Units Up to 28336 records 8096 USER CARD 80 ZONE TABLE 32 SENSOR TABLE 28336 REC QUEUE User Cards :

Time Zone Table : Sensor Table :

Up to 8096 user cards Up to 80 zone table

(34)

1. Find and get the Screw Mounting template from the box and stick the template on the wall where you want to put the AC9400 unit.

2. Drill the 4 mounting holes through the Screw Mounting template if the wall is concrete.

3. Get 4 pieces of plastic bolts to insert into the 4 holes on the wall.

4. Use the special screw driver to remove the two special screws on the bottom of the unit to separate the front cover and back cover.

5. Get the back cover and have all the necessary wires go through the back cover and then mount the back cover on the wall with 4 screws through the screw mounting template.

6. Connect all the necessary wries into the connectors on the main unit put the front cover as the direction from top to bottom shown on the figure sketch.

7. Put the front cover with the back cover together.

8. Use the special screw driver to mount the two screws at the bottom of the unit and then stick the plastic plate to cover the screws.

9. Installation is finished.

AC-9400

INSTALLATION

(35)

2. Get the back cover out of the front cover.

3. Put the back cover on the wall and drill the holes on the wall to mount the back cover on the wall. you must have all the necessary wires go through the back cover before you mount it on the wall. 1. Use the special screw driver to remove the two special screws at the bottom of the PCR943 unit

to separate the front cover and back cover. 5. Put the front cover with the back cover together.

7. Use the plastic plate to cover the two screws.

8. Installation is finished.

PCR-943

INSTALLATION

on the front unit and then put the front cover on the back cover as the direction from top to bottom shown on the figure sketch.

6. Use the special screw driver to mount the two special screw at the bottom of the unit.

(36)

1.Do not install the external readerright on the back side of the Main unit to avoid mutual interference of the two RFID readers. If you have to install the external reader on the back side of the main unit,it must keep minimum 50 cm distance between the main unit and the external reader.

50 cm

AC9400

PCR943A-01

PCR943-01

GP30

AC9400

PCR943A-01

PCR943-01

GP30

2.Better install the external reader aside from the Main unit at a distance 50 cm minimum to avoid multual interference.

(37)

4C AWG #24 WAS1465 2C AWG #18 WAS1466 2C AWG #18 WAS1466 2C AWG #24 WAS1465 2C AWG #24 WAS1467 5C AWG #28 WAS1436 2C AWG #22 APR-1014 2C AWG #24 --5C AWG #24 WAS-1432 2C AWG #24 WAS-1432 9C AWG #24 --NEXT AC9400 3. AC9400 SYSTEM ALARM LOCK SENSOR SENSOR CON485 PC AC9400 POWER EXTERNAL READER PUSH BUTTON AUX. POWER