• No results found

This manual is also available on the DMV website,

N/A
N/A
Protected

Academic year: 2021

Share "This manual is also available on the DMV website,"

Copied!
40
0
0

Loading.... (view fulltext now)

Full text

(1)
(2)

understand safe driving practices. Study this manual to prepare for the knowledge test, obtain a Virginia driver’s license and become a safe driver.

The information contained in this manual should be used as a general guide to the motor vehicle laws but not as a substitute for the Code of Virginia, which contains the laws that govern Virginia drivers and vehicles.

If you are learning to drive, this manual will give you information you need to study for the knowledge exam. If you already have a Virginia driver’s license, review this manual for new laws or rules of the road.

Driving is a privilege, not a right. Your driver’s license carries with it a great

responsibility to be courteous of other drivers on the roadways and follow state and federal motoring laws.

This manual is also available on the DMV website, www.dmvNOW.com. DMV offers the Virginia Driver’s Manual in an audio format for Virginians with special needs. The audio version is available at www.dmvNOW.com.

(3)

Section 1 – Testing

Two-part knowledge exam ...3

Road skills test ...4

Vision screening ...4

Vision standards ...4

Section 2 – Signals, Signs and

Pavement Markings

Traffic signals ...5

Lane use signals ...6

Traffic signs ...6

Sign colors ...6

Sign shapes...7

Regulatory or guide signs ...7

Warning signs ...8

Work zones ...10

Pavement markings ...11

Painted curbs ...12

Section 3 – Safe Driving

Hand position ...13

Speed limits ...14

Stopping ...14

Yielding the right-of-way ...15

Roundabouts ...15

Changing lanes ...16

Passing ...16

Over-correcting ...17

Turning ...17

U-turns ...17

Turn signals ...17

Maintaining a space cushion ...18

Following distance ...18

Virginia Driver’s Manual:

Table of Contents

Searching ...18

Blind spots ...19

Sharing the road ...19

Pedestrians ...19

Bicycles ...19

Mopeds ...19

Motorcycles ...19

Light rail ...20

Low speed vehicles ...20

Trucks, tractor-trailers, buses and RVs ...20

Light to medium trailers ...20

Backing ...21

Parking ...21

Visibility ...21

Lights ...21

Hazardous conditions ...21

Night driving ...21

Fog ...22

Rain ...22

Snow ...22

Dangerous driving behaviors ...22

Aggressive driving ...22

Distracted driving ...22

Drowsy driving ...23

Drinking and driving ...23

Traffic crashes ...24

Deer hazards ...24

Traffic stops ...24

Section 4 – Seat Belts, Airbags, and

Child Safety Seats

Seat belts ...25

Air bags ...25

(4)

|

Section 5 – Penalties

License suspension ...27

License revocation ...27

Conviction-related suspensions and revocations ...27

Other DMV requirements, suspensions and revocations ...28

Driver Improvement Program ...28

Medical review program ...28

Insurance monitoring program ...29

Suspension for failing to satisfy child support-related requirements ...29

Alcohol and the law ...29

Administrative License Suspension ...29

Open alcohol containers in vehicles ...29

Transporting children while under the influence of alcohol/drugs ...29

Vehicle impoundment ...30

Restitution ...30

Alcohol related violations and penalties involving persons under age 21 ...30

Section 6 – License Types

Learner’s permit ...31

Driver’s license ...31

Commercial driver’s license ...32

School bus driver’s license ...32

Motorcycle learner’s permit ...32

Motorcycle driver’s license ...32

International driver’s license ...32

Section 7 – Other Important

Information

Receiving your license by mail ...33

Address Changes ...33

New to Virginia ...33

Titles, registrations, license plates, decals ...33

Safety inspections ...34

Insurance requirements ...34

Applying to register to vote ...34

Organ, eye and tissue donation ...34

Section 8 – Sample Knowledge Exam

Sample exam ...35

(5)

In this section you’ll learn about:

Two-part knowledge exam

Road skills test Vision screening

Vision standards

Tests will include a vision screening and may

include a two-part knowledge exam and a road skills test. A DMV representative will tell you which tests you need to take.

Two-Part Knowledge Exam

You will need to take the knowledge exam if you do not hold a valid driver’s license from another U. S. state, Canada, Germany, France, or the Republic of Korea. The two-part knowledge exam is given on a computer and tests your knowledge of traffic signs, motor vehicle laws, and safe driving. Exam questions are taken from information in this manual. You must correctly answer all ten traffic sign questions in part one of the exam before you can take part two of the exam. Part two tests your general knowledge with multiple choice questions. You must answer at least 80 percent of these questions correctly to pass part two. If you fail the exam and you are:

Under age 18 – by law you must wait a full 15 days before you can retake the exam. For example, if you fail the exam on January 1, the earliest you can take the exam again is January 17.

Age 18 or older – you must pay a $2.00 fee if you retake the exam within 15 days.

The exam may be taken only once per business day. An audio version of the exam is available and the exam is offered in many different languages and American Sign Language. Therefore, translators may not be used for tests in offered languages. If you fail the driver’s license knowledge exam three times, you will not be able to take it a fourth time until you complete and pass the classroom part of driver education at a driver training school approved by DMV or the Department of Education. Customers age 19 and older have the option of completing

Section 1:

(6)

|

a course based on the Virginia Driver’s Manual. The completion date for each course must be after the date you failed the knowledge exam the third time. When you successfully complete the course and give DMV your certificate of completion, you can take the knowledge exam again. When testing, you cannot:

get help while taking the exam help another person taking the exam

try to get test questions or answers before the exam give another person exam questions or answers use a cell phone during the exam

A sample knowledge exam is in Section 8 of this manual and at www.dmvNOW.com.

Services for Persons With Disabilities

Customers with special needs or who require special help with applications or testing should tell a DMV staff member at any DMV location.

Road Skills Test

You will need to take the road skills test if you do not hold a valid driver’s license from another U. S. state, Canada, Germany, France, or the Republic of Korea. You must provide a vehicle for the road skills test (cannot be taken in an autocycle). The vehicle must have a valid safety inspection sticker, license plates, registration card and decals, working brakes, safety belts, horn, lights, turn signals, mirrors and speedometer.

To take the road skills test, the DMV examiner will require that you either:

present an acceptable driver’s education certificate of completion, or

complete a behind-the-wheel checklist (DMV form CSMA 19 available at www.dmvNOW.com or any DMV office) that describes specific driving tasks that you may be asked to perform while taking the road skills test. A licensed driver will need to certify on the form that he/ she has been with you while you practiced the driving tasks and that you have complied with all requirements for learner’s permit holders while operating a motor vehicle.

For applicants under 19, the road skills test will be given as part of the driver education course taken at a public, private or commercial driving school. If you are home schooled, refer to the Home-Schooled In-Car Driver Education Information Sheet (HS 3) for more information about taking the road skills test.

Applicants age 19 or older must hold the learner’s permit for 60 days prior to the first road skills test or complete a course of driver’s education at a driver training school approved by DMV or the Department of Education. For applicants who

choose to take driver’s education, the road skills test will be administered by the driver training school. For those who opt to hold a learner’s permit for 60 days, the road skills test will be given by a DMV staff member. The test may be taken only once per business day. If you fail the road skills test, you must wait two days to take it again. If you fail the road skills test at DMV three times, you will not be able to take it a fourth time until you complete and pass the in-vehicle part of driver education at a driver training school approved by DMV or the Department of Education. The completion date for the in-vehicle part must be after the date you failed the road skills test the third time. Once you successfully complete the in-vehicle part and give DMV your certificate of completion, you can take the road skills test again.

Vision Screening

To screen your vision, a DMV staff member will ask you to look into a machine and read a series of letters or numbers. The vision screening is not a medical exam. The screening shows whether your vision meets Virginia’s standards to safely drive. If you fail the vision screening, you may be asked to visit an eye care professional.

If you need to wear glasses or contact lenses to pass the vision screening, you must wear them when you drive. Your license will display an X for this restriction. To have this restriction removed after having laser surgery to correct your vision, you must visit a DMV customer service center and pass the vision screening without wearing glasses or contact lenses or submit a Vision Screening Report (MED 4).

Vision Standards

Driver’s license – unrestricted

20/40 or better vision in one or both eyes, and

100 degrees, or better, horizontal vision in one or both eyes, or comparable measurement that shows a field of vision within this range.

Driving – restricted to daylight hours only

20/70 or better vision in one or both eyes, and 70 degrees, or better, horizontal vision. If you have

vision in only one eye, you must have horizontal vision of at least 30 degrees or better when looking toward your nose and 40 degrees or better when looking toward your temple, or comparable measurement that shows a field of vision within this range.

A daylight driving only restricted license permits you to drive only during the period of time beginning a half-hour after sunrise and ending a half-hour before sunset.

Bioptic telescopic lenses: If you wear bioptic telescopic lenses, read the DMV publication Driver’s Licensing Information for Bioptic Telescopic Lense Wearers (MED 44) available at www.dmvNOW.com or contact DMV

(7)

In this section you’ll learn about:

Traffic signals Traffic signs Pavement markings

Painted curbs

Traffic signals, signs and

pavement markings

are used for traffic control to provide a smooth, orderly flow of traffic. It is important to understand and obey them. It is illegal to avoid these traffic controls by cutting through a parking lot or field. Obey all signs and signals unless directed by a police officer; always follow the officer’s direction.

Traffic Signals

Traffic signals apply to drivers, motorcycle riders, bicyclists, moped-riders and pedestrians.

Red light: At a red light, come to a complete stop at the stop line or, if there is no stop line, before entering the intersection or before reaching the crosswalk. Remain stopped as long as the signal is red, unless turns are allowed.

Right turn on red: You may turn right while the traffic signal displays a red light. Before turning, you must come to a complete stop. Look both ways and yield the right-of-way to pedestrians and other traffic. Be sure to check for less visible vehicles such as motorcycles, bicycles and mopeds. You may not turn right on red if signs are posted at the intersection that read “No Turn on Red,” or if a red arrow pointing to the right is displayed.

Left turn on red: You may turn left at a red light if you are on a one-way street and turning left onto another one-way street while the traffic signal displays a red light. Before turning, you must come to a complete stop. Look both ways and yield the right-of-way to pedestrians and other traffic. Be sure to check for less visible vehicles such as motorcycles, bicycles, and mopeds. You may not turn left on red if signs are posted at the intersection that read “No Turn on Red,” or if a red arrow pointing to the left is displayed.

Section 2:

Signals, Signs and

Pavement Markings

(8)

|

Red arrow: A red arrow means you must stop if you intend to move in the direction of the arrow. You may not

proceed in the direction of the arrow as long as the red arrow is displayed, unless signs are posted at the intersection that read “Right on Red Arrow After Stop” or “Left on Red Arrow After Stop.” Virginia law prohibits right and left turns at red arrow lights.

Note: If you are traveling in another state, make sure you know its laws for right and left turns at red and red arrow lights. Flashing red light: At a flashing red light, come

to a complete stop and yield to oncoming vehicles and pedestrians. You may go when the way is clear. At a railroad crossing, you must come to a complete stop even if you don’t see a train.

Flashing red arrow: At a flashing red arrow, come to a complete stop, yield the right-of-way to vehicles coming from the other direction and pedestrians in the intersection, and proceed in the direction of the arrow when the way is clear. Yellow light or arrow: A yellow light or arrow are cautions warning that the light is about to change. If you have not entered the intersection, stop;

or, if unsafe to stop, cautiously go through it. If you are already in the intersection, go through it cautiously. Do not speed up to beat the light.

Flashing yellow light: A flashing yellow light means slow down and proceed with caution. Flashing yellow lights are at locations with higher-than-normal hazardous conditions.

Flashing yellow arrow: At a flashing yellow arrow, you may turn in the direction of the arrow, if the way is clear. Yield the right-of-way to vehicles coming from the other direction and pedestrians in the intersection. Be sure to check for less visible vehicles such as motorcycles, bicycles, and mopeds. If a traffic light changes from red to flashing yellow arrow while a pedestrian is in the intersection, allow the pedestrian to cross the street before turning.

Green light or arrow: At a green light, you may go if the way is clear. At a green arrow, you may go in the direction of the arrow if the way is clear. If you are turning, you must yield the right-of-way to vehicles coming from the other direction and pedestrians in the intersection. Be sure to check for less visible vehicles such as motorcycles,

bicycles, and mopeds. If a traffic light changes from red to green while a pedestrian is in the street, allow the pedestrian to cross the street before turning.

Out of service signals: When traffic signals are not working because of a power outage or other problem and not displaying any lights, you are required to stop, proceeding through the intersection as though it were an all-way stop. This does not apply if a law enforcement officer or other authorized person is directing traffic at the intersection, or if portable stop signs are in use.

Lane use signals

indicate lanes where you can and cannot drive during different hours of the day.

Red X: Never drive in a lane marked with a red X signal.

Yellow X: A yellow X signal means that you should move out of the lane as soon as safely possible.

Green Arrow: You are permitted to drive in a lane marked with a green arrow signal.

Left-turn Arrow: You are permitted to enter in a lane marked with a one-way or two-way arrow only to turn in the direction of the arrow.

Traffic Signs

The color and shape of a traffic sign

communicates important information about the sign’s message. In poor visibility conditions, such as heavy fog, you may be able to make out only the shape of a sign. As you approach a sign and while still distant, you may see the color long before you can read the message or see the symbol, giving you some advance information.

Sign Colors

Sign colors help you know what the intention of the sign is. Red used with white conveys stop, yield, do not, and no. Stop signs, yield signs, do not enter or wrong way signs, the circle and slash in a no turn sign, and the restrictions in a parking sign are examples.

Black used with white conveys regulatory information. Speed limit, do not pass, no turns are examples where the operation is regulated by law and the black and white sign would be found. Yellow used with black conveys a warning. Curve ahead, stop ahead, overhead clearances, slippery when wet, are all examples. A specialized class of warning signs uses a strong yellow/green color with black to advise of school zone activities and other pedestrian activities.

(9)

Green and white, blue and white, and brown and white signs are used to provide helpful information. The green sign is used to provide destination types of information, while the blue sign is used to inform regarding motorists services. The brown sign is used to advise of historical or cultural interests that might exist in the area.

Orange and black and pink and black signs are used to advise and warn in construction (orange) and incident (pink) areas. They are used with black and white signs that convey regulations that might exist only because of the construction effort or the incident.

Sign Shapes

Octagon (Stop): This eight-sided shape always means stop. You must come to a complete stop at the sign, stop line, pedestrian crosswalk or curb. Wait for any vehicle or

pedestrian to clear the way. At some intersections you’ll find a sign beneath the stop sign that reads “All Way” or “4 Way.” At these intersections all vehicles on all roads leading into the intersection must stop. If you get to the intersection at the same time as other vehicles, the driver on the left must yield to the driver on the right.

Triangle (Yield): You must slow down as you come to the intersection. Be prepared to stop. Let any vehicles, pedestrians or bicyclists safely pass before you proceed.

Rectangle (Regulatory or Guide): Vertical signs generally give instructions or tell you the law. Horizontal signs may give directions or information.

Diamond (Warning): These signs warn you of special conditions or hazards ahead. Slow down and drive with caution. Be ready to stop.

Pentagon (School Zone/School Crossing):

This five-sided shape marks school zones and warns you about school crossings. Signs may display horizontal lines indicating the point at which a

crosswalk exists. Two signs may be used together to show the actual location of the crosswalk.

Regulatory or guide signs inform you

of the law; you must obey their instructions. Remember that a red circle with a slash means NO — the symbol inside the circle tells you what is prohibited.

Speed Limit: These signs tell you the maximum legal speed that you may drive on the road where the sign is posted when weather

conditions are good. During rain, snow and ice, you may receive a ticket for driving too fast for the conditions even if you are driving at or less than the posted speed limit.

Do Not Enter – Wrong Way: These signs mean you cannot drive in that direction. If you drive past these signs you are going in the wrong direction and could get into a head-on crash with vehicles headed your way. Cautiously turn around.

One Way: Traffic flows only in the direction of the arrow.

No Left Turn: Left turns are against the law. In Virginia, U-turns are considered as two left turns and are illegal if this sign is posted.

No Right Turn: Right turns are illegal. Do not make a right turn when you see this sign.

No U-Turn: U-turns are illegal. Do not make a U-turn when you see this sign.

No Turn on Red: You may not turn on the red light. Wait for the signal to turn green.

Do Not Pass: This sign marks the beginning of a no passing zone. You may not pass cars ahead of you in your lane, even if the way is clear.

(10)

|

Left Turn Yield on Green: This sign is used with a traffic signal. It tells you that the traffic turning left at a green light does not have the right-of-way and must yield to traffic coming from the other direction. Stop and look for oncoming traffic, then proceed with caution.

Keep Right: A traffic island, median or barrier is ahead. Keep to the side indicated by the arrow.

Lane Use Control: These signs are used where turns are required or where special turning movements are permitted for specific lanes. Traffic in the lane must turn in the direction of the arrow.

High Occupancy Vehicle: These signs indicate lanes reserved for buses and vehicles with a driver and one or more passengers as specified on the sign.

Disabled Parking: Parking spaces marked with these signs are reserved for people with disabled parking permits.

Warning signs alert you to possible hazards ahead. Slow

down and watch for other signs or signals that may follow.

Advisory Speed: This sign indicates the maximum safe speed for a highway exit.

Reduced Speed Limit Ahead: Prepare to reduce your speed; the speed limit is changing ahead.

Signal Ahead: Traffic signals are ahead. Slow down and be ready to stop.

No Passing Zone: This sign marks the beginning of a no passing zone. You may not pass cars ahead of you in your lane, even if the way is clear.

Merge: Two lanes of traffic moving in the same direction are about to become one. Drivers in both lanes are responsible for merging safely.

Lane Reduction: The right lane ends soon. Drivers in the right lane must merge left when space opens up. Drivers in the left lane should allow other vehicles to merge smoothly.

Divided Highway Begins: The highway ahead is split into two separate roadways by a median or divider and each roadway is one-way. Keep right.

Divided Highway Ends: The highway ahead no longer has a median or divider. Traffic goes in both directions. Keep right.

Roundabout: These signs indicate a circular intersection with an island in the center is ahead. Also called rotaries or traffic circles, these intersections may have one or more lanes. Entering traffic must yield the right-of-way to traffic already in the circle.

Slippery When Wet: When pavement is wet, reduce your speed. Do not brake hard or change direction suddenly. Increase the distance between your car and the one ahead of you.

Low Clearance Sign: The overpass ahead has a low clearance. Do not proceed if your vehicle is taller than the height shown on the sign.

Hill: A steep grade is ahead. Check your brakes.

Deer Crossing: Deer cross the roadway in this area. Slow down, be alert and be ready to stop.

(11)

Section 2: Signals, Signs and Pavement Markings

Pedestrian Crossing: Watch for people entering a crosswalk or crossing your path. Slow down and be prepared to stop. A second sign with an arrow may show the actual location of the crosswalk.

Bicycle Crossing/Bike Path: Bicycles regularly cross or ride beside traffic in this area. Drive with caution. A second sign with an arrow may show the actual location of the bike crossing.

School Zone/School Crossing: Slow down. The speed limit is usually 25 MPH. Watch out for children crossing the street or playing. Be ready to stop. Obey signals from any crossing guards. A second sign with an arrow may show the actual location of the crosswalk.

Open Joints: Slow down. Open joints on bridges or ramps could cause a motorcyclist to lose control of the motorcycle.

Expansion Joints: This sign is used when a joint across lanes creates a bump or is wide enough to cause loss of traction in wet weather.

Crossroad: A four-way intersection is ahead. Be ready to yield the right-of-way.

Side Road: A road joins from the right. Be alert for vehicles entering the roadway you are traveling on.

Y Intersection: You must bear either right or left ahead.

T Intersection: The roadway you are traveling on ends ahead. Signal before turning right or left.

Right Curve – Side Road: The road ahead curves right and a side road joins from the left within the curve. Be alert for vehicles entering the roadway you are traveling on.

Sharp Right Turn: Slow down and be prepared for a sharp right turn in the road ahead.

Sharp Right and Left Turns: Slow down and be prepared for the road ahead to turn sharply right, then left.

Right and Left Curves: The road ahead curves right, then left. Slow down.

Right Curve with Safe Speed Indicator: The road ahead curves right. Slow down to the safe speed limit indicated.

Winding Road: The road ahead winds with a series of turns or curves. On all curves, slow down for better control.

Low Ground Railroad Crossing: A steep slope where the railroad tracks cross the road may cause the bottom of low vehicles to get caught or drag on the tracks.

Railroad Crossing: Advance warning signs are placed before a railroad crossing. These signs warn you to look, listen, slow down and be prepared to stop for trains or any vehicles using the rails.

Railroad Crossbuck: This sign is a warning of a railroad crossing. Look, listen, slow down and be prepared to stop for trains or any vehicles using the rails.

Railroad Crossbuck and Track Indicator: If there is more than one track, the sign below the crossbuck will indicate the number of tracks at the crossing. Slow down and be prepared to stop.

(12)

|

In a work zone, the lives of highway construction workers

depend on drivers like you obeying the posted speed limits. If you are convicted of exceeding the speed limit in a highway work zone, you may be fined up to $500. Remember, the color orange marks a work zone and means slow down and be alert. Rough Road, Bump, or Uneven Lanes: These signs are used when certain road conditions, such as loose gravel or road construction, affect

the roadway surface and create potentially difficult conditions for motorists, especially motorcyclists.

Road Construction Ahead – Detour: These signs indicate a change in the traffic pattern or route ahead. Slow down. Unusual or potentially dangerous conditions are ahead.

Flashing Arrow Panels: Large flashing arrow panels or flashing message signs in work zones direct drivers to proceed into different traffic lanes and inform them that part of the road ahead is closed.

Flaggers: Flaggers are construction workers who normally wear orange or yellow vests, or yellow-green shirts or jackets. They use STOP/SLOW paddles and red flags to direct traffic through the work zone and to let other workers or construction vehicles cross the road.

Traffic Control Devices:

Barricades, vertical signs, concrete barriers, drums and cones are the most common devices used to guide drivers safely through work zones. When driving near the devices, keep your vehicle in the middle of the lane and obey the posted speed limit. As you leave the work zone, stay in your lane and maintain your speed. Don’t change lanes until you are completely clear of the work zone.

Message Boards: You may see portable or permanent message boards along roadways. They provide information about traffic, road, weather or other hazardous conditions. Always obey any directions posted on these message boards. For information about road conditions or road construction, visit the Virginia Department of Transportation website at www.virginiadot.org.

Railroad Crossbuck and Flashing Lights: Flashing lights may be used with crossbuck signs. Always stop

when the light begins to flash and be alert for approaching trains. Do not proceed until all trains or any other vehicles using the rails have passed, the tracks are clear, and the lights are no longer flashing. Be especially alert at multi-track crossings because a second train could be approaching from the opposite direction. Crossbuck, Flashing Lights and Gate: Gates are used with flashing light signals at some crossings. Stop when the lights begin to flash and before the gate lowers. Remain stopped until the gates are raised and the lights stop flashing. Do not attempt to drive around the

lowered gate.

Pavement markings, consisting of an X and RR, may

be painted on the pavement at the approach to some crossings. When approaching railroad tracks, be alert. Trains may approach the crossing at any time and from either direction. Unless you can clear the tracks completely, never start across the tracks.

Make sure there is room for your vehicle on the other side of the tracks before proceeding.

Note: School buses must always stop at railroad crossings, even when the lights are not flashing.

If a dangerous condition exists at a rail crossing, call the number listed on the emergency sign. This will allow the rail company to stop or reroute approaching rail traffic until the hazard is removed. Be sure to give the posted crossing number so that the hazard can be identified correctly.

If your car stalls on the tracks, don’t hesitate. Get out of the car right away and run diagonally away from the tracks in the direction of the oncoming train.

(13)

Double solid yellow lines mark the center of the road and separate traffic traveling in two different directions. Passing is not allowed in either direction. You may not cross the lines unless you are making a left turn.

Broken white lines separate lanes of traffic going in the same direction. You may change lanes with caution.

Dotted white lines are actually small rectangles in a series where each is closely spaced to the next. They are used to show lane assignment in intersections and interchanges where there might otherwise be a tendency to drift out of a lane or an area of intended use. Often they are used to guide two turning lanes through the intersection. Dotted white lines are also used to denote the opening of a turn lane at an intersection and entrance/exit lanes at interchanges.

Many two-lane roads in Virginia do not have lane markings to separate the lanes. On an unmarked two-lane road, you may pass a slow moving vehicle on the left side if there are no signs prohibiting passing. Make sure that the way is clear. Solid white lines show turn lanes and discourage lane changes near intersections, and at other locations where lane changes might

be dangerous. Solid white lines also mark the right edge of pavement. Arrows used with white lines indicate which turn may be made from the lane. Stop lines, crosswalks and parking spaces also are marked by white lines.

Section 2: Signals, Signs and Pavement Markings

Slow Moving Vehicles

travel at 25 MPH or less, such as farm equipment and horse-drawn vehicles,

must display these signs when using a public highway. Be prepared to adjust your speed or position when you see a vehicle with one of these signs.

Pavement Markings

Road markings guide and warn drivers as well as regulate traffic. Markings may be red, blue, yellow or white. They may be used alone or in combinations. Each has a different meaning.

Red markings are generally not used; but, some communities do use red curbs to indicate no parking zones.

Red reflectors on the pavement show areas not to be entered or used. They are positioned on the road surface so that only traffic flowing in the wrong direction would observe them. Blue markings show parking spaces for persons with disabilities.

Yellow center lines mean two-way traffic, flowing in opposite directions.

Broken yellow center lines mean that passing on the left is allowed in either direction when the way ahead is clear.

A broken yellow line

alongside a solid yellow line means that passing is allowed from the side of the broken line, but not from the side of the solid line.

(14)

|

White lane arrows are curved or straight. If you are in a lane marked with a curved arrow or a curved arrow and the word ONLY, you must turn in the direction of the arrow. If your lane is marked with both a curved and straight arrow, you may turn or go straight.

Double solid white lines separate lanes of traffic going in the same direction. Most often they are used to designate special use lane from conventional lanes, as when used to separate a High Occupancy Vehicle lanes from the other lanes of an expressway. You may not cross these lines. You may enter the designated special use lane only where signs and markings allow.

Yield ahead symbol is an outline of a triangle painted in the lane before the place where you must yield.

Yield line is a line of

triangles extending across the roadway that may be used with a yield sign to show the point at which you must yield or stop, if necessary. A yield line is often seen at the entrance of a roundabout.

On three-lane roads with traffic moving in both directions, road markings show when drivers may use the center lane for making left turns or for passing.

If the center lane is marked by a single broken yellow line on both sides, drivers traveling in either direction may use the center lane for passing.

If both sides of the center lane are marked by a solid yellow line and a broken yellow line, drivers traveling in either direction may use the lane for making left turns. However, they may not travel further than 150 feet in this lane.

High Occupancy Vehicles (HOV) lanes are marked on highways by a diamond shape in the center of the lane. HOV lanes may also be special lanes separated by a barrier or solid double white lines. During heavy traffic periods, HOV lanes are reserved for buses, vanpools, carpools,

other high occupancy vehicles, motorcycles, and certain clean special fuel vehicles. Road signs show the minimum number of passengers a vehicle must carry (excluding motorcycles and clean fuel vehicles) to use the HOV lanes and the times that HOV restrictions are in effect. If the lanes are separated by a barrier, they are reversible. This means that during certain times of the day, traffic flows one way. During other times of the day, traffic flows in the opposite direction. This diamond-shaped marking may also indicate that the lane is reserved for use as a bike lane or bus lane.

A painted curb means that you must follow special rules to park there. Check with the locality for specific meanings. Generally, the colors on the curb mean:

White — Stop only long enough to pick up or drop off passengers.

Yellow — Stop only long enough to load or unload. Stay with your car.

Red — Do not stop, stand or park.

Blue — Parking is reserved for persons with disabilities.

(15)

Every time

you get behind the wheel, you accept responsibility for your actions. You must obey Virginia’s traffic laws, and ensure the safety of you, your passengers, and other motorists, pedestrians and bicyclists on the roadways.

Hand Position

Sit straight but relaxed and place your hands on the steering wheel. If your steering wheel were a clock, your hands should be at the 8 o’clock and 4 o’clock positions. Hold the wheel with your fingers and thumbs. Avoid gripping it with your palms.

Section 3:

Safe Driving

In this section you’ll learn about:

Hand position Speed limits Stopping

Yielding the right-of-way Roundabouts

Changing lanes Over-correcting

Turning U-turns Turn signals

Maintaining a space cushion Searching Blind spots

Sharing the road Backing Parking Visibility Lights

Hazardous conditions Dangerous driving behaviors

Traffic crashes Deer hazards

(16)

|

Speed Limits

A speed limit is the maximum legal speed you can travel on a road under ideal conditions. You may drive slower than the posted speed, but it is illegal to drive any faster. By law, you must drive slower if conditions such as road construction or bad weather make the posted speed unsafe. It is illegal to use a radar detector in Virginia.

Maximum speed limit for

passenger vehicles and motorcycles

(unless posted otherwise)

Type of highway or zone Speed limit Interstate highways in certain rural areas 70 MPH Non-rural interstate highways, public

roads not part of the interstate system 55 MPH Rural rustic and unpaved roads 35 MPH School, business and residential zones

(You are required to travel 25 MPH in a school zone only when indicated by a sign or signal. Otherwise, maintain the posted speed.)

25 MPH

Stopping

You must always stop your vehicle:

at all stop signs, red traffic lights and flashing red signals when entering a street or crossing over a sidewalk from

a driveway, alley, building or parking lot at railroad crossings with flashing signals when signaled by flaggers directing traffic

for pedestrians attempting to cross the street at a crosswalk

at the direction of a police officer. If you don’t obey a law enforcement officer’s signal to stop and the officer pursues you and is killed as a direct result of the pursuit, you will be guilty of a Class 4 felony.

at the scene of a crash in which you are involved When approaching a stop sign and the car in front of you proceeds, stop at the sign and proceed when the way is clear.

Stopping for School Buses

In the following pictures, the red vehicles must stop and remain stopped until all children are clear of the roadway and the bus moves again.

You must stop for stopped school buses with flashing red lights and an extended stop sign when you approach from any direction on a highway, private road or school driveway. Stop and remain stopped until all persons are clear and the bus moves again.

You must also stop if the bus is loading or unloading passengers and the signals are not on.

You do not have to stop if you are traveling in the opposite direction on a roadway with a median or barrier dividing the road and the bus is on the opposite side of the median or barrier. However, be prepared for unexpected actions by persons exiting the school bus.

Stopping Distance

Three factors determine the distance that it takes to stop your vehicle: perception time, reaction distance and braking distance.

Perception time: The time it takes you to recognize a hazard. Reaction distance: The distance your vehicle travels between the time you recognize a problem and the time you apply the brakes.

Braking distance: The distance your car travels after you apply the brakes.

Perception time, reaction distance and braking distance are affected by weather, visibility, and your mental and physical condition. Braking distance is also affected by how fast your vehicle is traveling, the condition of your brakes and tires, and the pavement condition. For example, wet pavement can double your braking distance.

(17)

Section 3: Safe Driving

Average stopping distance on dry, level pavement.

Source: Code of Virginia Section 46.2-880

Antilock Brakes

If your vehicle has antilock brakes, be sure that you understand how they work. Check your vehicle owner’s manual and practice braking before you go out on the road. Remember, never pump antilock brakes.

Yielding the Right-of-Way

Yield also means to stop if you cannot merge safely into the flow of traffic.

Examples of yielding the right-of-way:

When two vehicles from different directions arrive at an intersection at different times, the vehicle that arrives first goes first.

When two vehicles from different directions arrive at the same time at an intersection with no signs or signals, the driver on the left must allow the driver on the right to go first.

If the traffic lights at an intersection are not working, all vehicles coming to the intersection must stop. The driver on the left must yield to the driver on the right. Drivers entering an interstate from an entrance ramp

must yield the right-of-way to traffic already on the highway.

Drivers entering any intersection or traffic circle must yield to traffic already in it.

When entering a roadway from a private road or driveway, you must stop and yield to all traffic and pedestrians.

You must yield for pedestrians who are crossing a street within a clearly marked crosswalk or at an unmarked intersection. Remember that turns on red are especially hazardous to pedestrians. Avoid conflict with pedestrians and permit them to cross the street safely. You must yield to funeral processions. Do not cut

through, join or interfere with a funeral procession. Unless led by a police escort, the lead vehicle in a funeral procession must obey all traffic signs and signals.

Other drivers in the procession may follow carefully without stopping and may use hazard lights (flashers) to indicate they are in the procession.

You must yield to all military convoys. Never cut through or join a military convoy.

Yielding to Vehicles with Flashing Lights

Drivers must take specific actions when they see vehicles with flashing or blinking blue, red, yellow or white lights on roadways.

Stopped vehicles

When approaching a stopped vehicle with flashing lights on a four lane highway, you must change to a lane not next to the emergency vehicle, if you can change lanes safely. If you are unable to safely change lanes, reduce your speed and proceed with caution. Violations can result in court suspension of your driver’s license and demerit points on your driving record.

You may not park within 500 feet of where fire trucks or equipment are stopped answering an alarm.

Approaching vehicles – same direction

Never follow an emergency vehicle closer than 500 feet when its lights are flashing.

When police, fire and rescue vehicles or ambulances approach you from behind your vehicle using a siren, flashing lights or both, you must immediately yield the right-of-way. Safely pull over to the right edge of the road and stop until the emergency vehicle has passed. Approaching vehicles – opposite direction

When emergency vehicles approach you in the opposite lane on an undivided highway, you must pull over to the edge of the road and stop until the emergency vehicle passes.

These requirements do not apply in highway work zones.

Roundabouts

Roundabouts, rotaries, circular intersections and traffic circles are all terms for intersections with a circular

island in the center. Roundabouts may have one or more lanes. Entering traffic must yield the right-of-way to traffic already in the circle. Each road approaching the roundabout is marked with a yield sign and may also have

yield line markings on the pavement. However, rotaries and other circles may have stop signs. Drivers must pay attention and obey the signs.

When approaching a roundabout, slow down. Use your turn signals to indicate where you want to go. If you plan to turn right, stay to the right as you enter the roundabout. If you plan to go straight, you may stay in either lane (if it is a dual lane circular intersection). If you plan to turn left, stay to the left as you enter the roundabout.

(18)

|

More information about driving safely through a roundabout is available at the Virginia Department of Transportation web site at http://www.virginiadot.org/info/faq-roundabouts.asp. Tips for driving safely through a roundabout:

As you approach the roundabout, slow down; look for the street and direction signs. This will help you know which exit to take. These signs should be posted along the roadside before you reach the roundabout. When you arrive at the roundabout, yield the

right-of-way to pedestrians and bicyclists. You also must yield to any vehicles already in the roundabout. Sometimes your entry point will be controlled by a stop or yield sign, or traffic signal. When the way is clear, you may enter the roundabout.

While inside the roundabout, stay in your lane until you are ready to exit. Use your vehicle’s right turn signal to let drivers around you know what you want to do. Do not change lanes or take an exit before checking

for vehicles that may be continuing through the roundabout in the lane next to you or behind you. Expect vehicles to be in blind spots you cannot see in your rearview or side mirrors. Quickly glance over your shoulder and check for any vehicles that may be in your blind spot.

Changing Lanes

Before changing lanes, check your side and rearview mirrors for traffic approaching you from behind. Then, use your turn signal to let other drivers know you plan to change lanes. Check for other drivers who also may be moving into the same lane. Just before you begin moving into the other lane, quickly glance over your shoulder and check for any vehicles that may be in your blind spot.

Whether you are changing lanes, passing, entering or exiting a highway, always use your turn signals and check traffic to the rear and sides. When driving on a multi-lane highway, stay in the right lane if you are driving slower than the traffic around you.

Passing

When passing another vehicle:

check the traffic ahead of you, behind you and in your blind spot before you attempt to pass. Signal and then accelerate to pass. Return to the right lane as soon as you can see the front of the passed vehicle in your rearview mirror.

it is against the law to exceed the speed limit as you pass.

complete the pass before you reach a No Passing zone. If you’re still in the left lane when you reach the zone, you’re breaking the law.

you may pass on the right if the vehicle you are passing has signaled and is

making a left turn. Be cautious because the vehicle you are passing may be blocking your view or blocking the view of other drivers. You may not pass on the right if you must drive off the pavement or main portion of the roadway to get around the other vehicle.

when approaching or passing a person riding a bicycle, moped, or power-assisted bicycle or other device, reduce speed and pass at least three feet to the left. When being passed, don’t speed up. Maintain a steady speed or slow down.

(19)

Section 3: Safe Driving

Passing is unlawful and unsafe:

on hills, curves, at intersections or railroad crossings, except on roads with two or more lanes of traffic moving in the same direction

off the pavement or shoulder of the road when a school bus is stopped to load or unload

passengers on a public road (unless a physical barrier or unpaved median separates traffic going in either direction) or on a private road

when a solid line marks the left side of your lane

Over-correcting

Over-correcting occurs when the driver turns the steering wheel more sharply than expected, causing the rear wheels of the vehicle to slide toward the outside of the turn. This may result in the loss of vehicle control.

Most over-correction crashes are single vehicle crashes and are often preventable. A driver should remain alert at all times. Reduce speed and use extra caution while driving on curved roads. If you veer off the road, curved or straight, do not panic. Gradually reduce your speed, look in the direction you want to go, slowly steer back onto the roadway.

Turning

To make a right turn you should be in the lane closest to the curb. Signal your intent to turn by using the proper turn signal. You should signal at least three or four seconds, 100 feet, ahead of the turn. Look to your left to check the intersection for pedestrians and traffic coming from the other direction. Then brake smoothly before and during the turn. If there is a traffic light or a stop sign at the intersection, come to a complete stop before you make the turn. Turn into the lane closest to the curb unless pavement markings lead you otherwise, and then change lanes if needed.

To make a left turn you should be in the furthest left lane possible, turning into the leftmost lane on the intersecting road, unless pavement markings lead you otherwise; or, unless multiple left turn lanes are provided. If multiple left turn lanes are provided, you should choose the lane that will best serve your need once you enter the intersecting road. Signal your intent to turn by using the proper turn signal. You should signal at least three to four seconds, 100 feet, ahead of the turn. Look in all directions, checking the intersection for pedestrians and traffic coming from the opposite direction. Keep your front wheels pointed straight ahead until you are actually going to make the left turn. This prevents you from being pushed into oncoming traffic if another vehicle crashes into you from behind. When the way is clear, make the left turn, yield to any vehicles (including bicycles and pedestrians) approaching from the opposite direction.

When two vehicles are approaching each other and signaling to turn left, both vehicles should turn in front of each other so that the passenger sides of the vehicles are beside each other.

U-Turns

U-turns are not legal everywhere. Before you make a U-turn, check for No U-Turn or No Left Turn signs. In business districts, cities and towns, U-turns are allowed only at intersections. Never make a U-turn on a highway.

When making a U-turn, turn on your left-turn signal, stop, and yield for approaching traffic. When the way is clear, proceed into the outside or right hand lane traveling in the opposite direction.

Turn Signals

When you plan to change lanes, turn, or enter or exit a highway, first give the proper turn signal. Using your turn signal, which is required by law, communicates your intended movement to drivers around you. Develop a good habit and use turn signals or hand signals even if no other traffic is on the road.

When you plan to turn, signal three or four seconds, 100 feet, ahead of your turn. Be aware that drivers planning to turn into your lane may not know exactly where you will turn; drivers may pull out in front of you. Be alert.

After you complete the turn or lane change, be sure the turn signal stops flashing.

Left Turn Left hand and

arm pointing straight out

Right Turn Left hand and

arm pointing upward

Slow or Stop Left hand and

arm pointing downward

Hand Signals

(20)

|

Maintaining a Space Cushion

Space around your vehicle gives you distance to react in emergencies and avoid a crash. Create a space cushion around your vehicle by staying in the middle of your lane. Make sure there is enough room ahead of your vehicle and behind it for other vehicles to pass or stop safely.

Use the two-, three- and four-second rule to determine if you are following far enough behind the vehicle ahead of you.

Following Distance

At these posted speeds and on dry surfaces, this distance, in seconds, allows the driver to steer and

brake out of a problem areas.

2 seconds Under 35 MPH

3 seconds 35-45 MPH

4 seconds 46-70 MPH

Here’s how the following distance rule works. Glance at the vehicle

ahead as it passes a fixed object, such as an overpass, sign, fence, corner or other fixed mark.

Begin counting the seconds it takes you to reach the same place in the road.

If you reach the mark before you have counted off two, three, or four seconds, depending on speed, you’re following too closely. Slow down and increase your following distance.

For bad weather conditions, heavy traffic, poor pavement or if your vehicle is in poor condition, add extra seconds to increase your following distance.

Drivers need to change following distance when speed or road conditions change. Hand response time is close to a half second. Foot response time is normally three-quarters of a second. This does not take into account any delay in perception time as a result of the driver being tired, on medication, distracted, etc. Road conditions, speed, driver alertness, and even following vehicles of different weights all change the ability to stop.

Increase your following distance when driving: behind a large vehicle that blocks your vision in bad weather or heavy traffic

when exiting an expressway behind a motorcycle when being tailgated

Tailgating is when the driver behind you is following too closely. If you find yourself in this situation, do not brake suddenly. If possible, move over to another lane, or gently tap your brakes to flash your brake lights and slow down. This should encourage the tailgater to pass you or slow down. Help the driver behind you by maintaining a safe following distance and a steady speed. Tap your brakes to warn the driver behind you when you plan to slow down or stop.

Searching

Searching means looking at the entire scene for anything that might come into your path. As you search the road, avoid staring at one thing. Keep your eyes moving and learn to read the road and your surroundings.

Looking ahead will help you identify risks early and provide you with more time to react. Expert drivers try to focus their eyes 20 to 30 seconds ahead. In the city, that equals approximately one block. Avoid staring at the middle of the road. Scan from side to side, checking for traffic signs and signals, cars or people that might be in the road by the time you reach them.

Search for clues on the road. Look for exhaust smoke, brake or back-up lights and turned wheels on vehicles. Clues like these warn that the vehicles may pull into your path. Watch for pedestrians, bicyclists and other slow moving vehicles that may be in the road ahead.

When driving in rural areas, watch for hidden intersections and driveways, curves, hills and different road conditions. Watch for other vehicles, especially trucks, oversized and slow-moving farm vehicles, and bicycles.

(21)

Section 3: Safe Driving

Bicycles: Bicycles are considered vehicles and have the same right-of-way as motor vehicles. Bicyclists are also expected to obey the same traffic rules and regulations as vehicle drivers; however, many are children who may not know or obey the rules. Slow down when you approach bicyclists. State law requires motorists to pass cyclists with at least three feet of clearance. Give them plenty of

room when passing and be prepared to stop suddenly. Look for bicycles on all public roads.

It is against the law to operate a bicycle or any electric power device such as assistive mobility devices, toy vehicles, and bicycles on any interstate highway.

Mopeds: It is against the law to operate a moped faster than 35 MPH or on an interstate highway. Any person who operates a moped faster than 35 MPH is considered to be operating a motorcycle which must meet Virginia registration requirements. In addition, the operator would be required to hold a valid driver’s license with a motorcycle classification or a driver’s license restricted to operating motorcycles only.

Moped riders must be at least age 16 and obey all rules of the road. They must carry some form of government-issued photo identification (does not have to be a driver’s license) that includes name, address and date of birth. As a driver, treat moped riders with the same care given to any other vehicle driver.

Riders and passengers must wear helmets, and use eye protection if the moped does not have a windshield. The moped must be titled and registered with DMV.

Although you do not need a driver’s license to operate a moped, you may not operate a moped if you have been declared a habitual offender and your license is suspended or revoked for driving while intoxicated.

Motorcycles: Approximately half of all fatal motorcycle crashes involve automobiles. Many crashes are caused by the motorist’s failure to see a motorcycle in traffic.

Look for motorcyclists. In more than half of all crashes involving motorcycles and automobiles, the other driver didn’t see the motorcycle until it was too late. Drivers are conditioned to look for four-wheeled vehicles; but they don’t expect to see two-wheeled vehicles. A motorcycle’s small size also makes it difficult to see.

Check your blind spots. A motorcycle’s small size allows it to slip into your blind spot easily. Always check for motorcycles before you pull out, change lanes, turn, back up or proceed through an intersection.

Never tailgate a motorcycle (or any other vehicle). Allow yourself plenty of braking distance by adding an extra second to the following distance rule. In inclement weather, double this distance.

Anticipate the motorcyclist’s movements. Although a motorcycle is not as wide as the lane, the rider will use the entire lane as traffic situations and road conditions change. A slight change or debris on the road surface can be a Check from left to right and then left again before

entering an intersection. Whenever you reach a place in the road where other cars, people or animals may cross your path, look both ways to be sure it is clear. These include intersections, crosswalks, shopping centers, construction areas and playgrounds. At any intersection, look to the left first, since cars coming from the left will be closer to you. Then look to the right and take one more quick look to the left before you drive through.

Look behind. Use your rearview mirror to check the traffic behind you frequently, about every 10 seconds. This will alert you if someone is moving up too quickly or tailgating you. Check the traffic behind you when changing lanes, backing up, slowing down quickly or driving down a long, steep hill.

Blind Spots

Blind spots are danger areas that cannot be seen in the mirrors on either or both sides of the vehicle.

The best way to see a car in your blind spot is by quickly turning your head and glancing over your shoulder to ensure the way is clear before changing lanes or passing another vehicle.

Avoid driving in someone else’s blind spot. This can be just as dangerous as not checking your own blind spot. Speed up or drop back; but, don’t stay in the other driver’s blind spot.

Sharing the Road

Drivers share the road with many other users: pedestrians, bicyclists, moped and motorcycle riders, trucks and buses, recreational vehicles and other vehicles of all shapes and sizes. It is your responsibility to adjust your driving to avoid other drivers’ mistakes and assure everyone’s safety.

Pedestrians: Generally, there are three types of pedestrians most often involved in crashes: children, the elderly and adults under the influence of alcohol or other drugs.

Be careful around schools, playgrounds and in residential areas where small children may be playing or crossing the street.

Look out for the elderly, who may have poor vision and hearing. Remember that the elderly and people with disabilities will move slowly.

Be especially aware of pedestrians when making a right or left turn. They have the right-of-way. Allow pedestrians to completely cross the street before beginning your turn.

Be alert for pedestrians at all times. Slow down and be prepared to stop.

(22)

|

major obstacle for a motorcyclist. Expect the motorcycle to make sudden moves within the lane. Never drive beside a motorcycle in the same lane.

Yield to motorcycles. The small size of a motorcycle can cause you to misjudge the motorcycle’s speed and distance. Before pulling out into traffic, check twice for motorcycles and use extra caution before you pull out in front of one.

Light Rail: There is a light rail train system in Norfolk called The Tide. Light rail trains share the road with motor vehicles and bicyclists, and they intersect with motor vehicle traffic at 27 locations along the 7.4 mile route. Stay safe when driving around The Tide by obeying the tips below.

Pay attention to changing traffic patterns and always follow the roadway.

Never drive around lowered crossing gates.

Always look both ways before turning across train tracks. Expect trains on any track at any time.

Always obey signs and traffic signals. Never stop, pass or shift on train tracks.

Don’t cross train tracks unless you have enough room to cross without stopping and can clear the tracks to a safe distance.

For more info about light rail safety, visit www.gohrt.com or call (757) 222-6100.

Low Speed Vehicles: These electrically powered four-wheel vehicles have a maximum speed ranging from 21 to 25 MPH. Low speed vehicles may be operated on public roads with speed limits of 35 MPH or less by licensed drivers or learner’s permit holders accompanied by a licensed driver. Low speed vehicles must comply with all federal safety standards and must meet Virginia’s requirements for passenger vehicle registration and insurance coverage. Golf carts are not classified as low speed vehicles.

Trucks, Tractor-Trailers, Buses and RVs: Trucks, tractor- trailers, buses and recreational vehicles (RVs) – including motor homes, campers and travel trailers – are longer, higher and wider than other vehicles. They accelerate slowly and require greater stopping and turning distances. Plus, there are danger areas around these vehicles where crashes are more likely to occur. These areas are called No-Zones. No-Zones on the side, front and rear also include blind spots where your car disappears from the driver’s view. Learning the No-Zones can save your life.

Side No-Zones: Trucks, tractor-trailers, buses and RVs have big No-Zones on both sides that are dangerous because these vehicles must make wide turns. These No-Zones or blind spots are much larger than your car’s blind spots. If you can’t see the driver’s face in his side view mirror, then he can’t see you.

Rear No-Zone: Trucks, tractor-trailers, buses and RVs have huge No-Zones directly behind them. The driver

can’t see your car behind his vehicle and you can’t see what’s happening in traffic ahead of his vehicle. If the truck, bus or RV brakes or stops suddenly, you have no place to go and could crash into the vehicle’s rear-end. Always maintain a safe following distance. Front No-Zone:

You could get rear-ended by a truck, bus or RV if you cut in front too soon after passing the vehicle or if you cut in front and then suddenly slow down. The truck, bus and RV drivers would be forced to slam on their brakes. These vehicles need nearly twice the time and room to stop as cars. A truck and its trailer may be as long as 65 feet and it may take you more than half a mile of clear road to pass. When passing, look for the entire front of the truck in your rearview mirror before pulling in front. And then, maintain your speed.

Wide Turns: Trucks, buses and RVs sometimes need to swing wide to the left or right to safely make a turn. They can’t see the cars directly behind or beside them. In fact, their blind spots may stretch up to 20 feet in front of the cab and approximately 200 feet behind the vehicle. Never try to squeeze between a truck, bus or RV and the curb or another vehicle.

Light to Medium Trailers: These trailers are attached to mid-sized cars and trucks with safety chains and a trailer hitch. Large side mirrors are generally needed to increase visibility. Towing a trailer places additional stress on the vehicle; it takes the vehicle twice as long to pass, stop, accelerate and turn. Remember the No-Zones described under Trucks, Tractor-Trailers and RVs. Before driving a vehicle with a light to medium trailer attached, perform a safety inspection before each trip. Ensure:

the pin securing the ball mount to the receiver is intact the hitch coupler is secured

safety chains are properly attached the electrical plug is properly installed

brake lights, turn signals, and license plate lights are functioning properly.

Before pulling a trailer on public roads, find a location such as a vacant parking lot to practice and get the feel for how your vehicle and trailer will handle.

(23)

Section 3: Safe Driving

When driving a vehicle with a light to medium trailer attached:

always allow for the added length of the trailer when you change lanes

if your trailer starts to sway, steer toward your target when backing up, place your hand on the bottom of

the steering wheel. If you cannot see where you are backing up, have someone outside to help guide you. To back the trailer to the left, use your left hand to move the wheel left. To back the trailer to the right, use your right hand to move the wheel to the right.

Backing

The most common mistake that drivers make when backing up is failing to look both ways behind them. Mirrors do not give you a full view. To see as much as possible, turn your body and head to the right and look out through the rear window. Back up slowly and check for pedestrians and approaching traffic by glancing quickly to either side.

Parking

When parking on a public road, move as far from traffic as possible. If you park on a shoulder, pull over as far on the shoulder as possible. If you park next to a curb, pull close to it. You may not park more than one foot from the curb. On a two-way street, park on the right side of the road. On a one-way road, park on either side.

Parking on a hill

With a curb: Turn the front wheels of your vehicle to prevent it from rolling into the street.

Without a curb: Turn the front wheels so that if the vehicle rolls, the rear of the vehicle will roll away from traffic.

You may not park:

beside another parked vehicle (double parking) on crosswalks or sidewalks

in front of driveways

within areas where parking is prohibited by curbs painted yellow or No Parking signs

in a parking space reserved for disabled persons on the hard surface of a road when no curb is present within 15 feet of a fire hydrant

within 20 feet of an intersection

within 15 feet of the entrance to a fire, ambulance or rescue squad station

within 500 feet of where fire trucks or equipment are stopped answering an alarm

within 50 feet of a railroad crossing

in such a way that you block or create a hazard for other vehicles in a designated traffic lane

Visibility

Most of what you do while driving depends on what you see. To be a good driver, you need to know what to look for, where to look, and how to adjust to possible problems. The single biggest contributor to crashes is failing to identify a risk. You must look down the road, to the sides, and behind your vehicle. You must also be alert for unexpected events. You must use your headlights at night and at other times when it’s hard to see. You must be alert and pay attention to what is going on around you.

Lights

Virginia law requires motorists to use headlights during inclement weather such as rain, fog, snow or sleet when visibility is reduced to 500 feet. You must use your headlights whenever you use your windshield wipers as a result of bad weather.

Hazardous Conditions

Driving becomes hazardous when visibility is reduced or when the road surface is covered with rain, snow or ice. Reducing your speed should be your first response to decreased visibility and dangerous road conditions. Increase your space cushion by doubling your normal following distance (refer to the Maintaining a Space Cushion section for more information). Turn on your headlights.

Night Driving

At sunset, as soon as light begins to fade, turn on your headlights to make your vehicle more visible to others. You must use headlights from sunset to sunrise.

Parking uphill — no curb

Turn front wheels right Parking

downhill — no curb Turn front

wheels right

Parking uphill — with curb

Turn front wheels left Parking

downhill — with curb Turn

front wheels right

References

Related documents

The stationary distribution is proportional to W 2 N , multiplied by a factor that reflects the pattern of mutation rates (Iwasa, 1988; Sella and Hirsh, 2005); this can be derived

Figure 1–2 HS241 with HS280 Diagram MODEL HS241 StorageWorks FDDI SERVER DEVICE CHANNEL PROCESSOR SERVER PROCESSOR FDDI INTERFACE FDDI INTERFACE FDDI INTERCONNECT OpenVMS Alpha OR

Post and print outline with source data as a Word document in BlackBoard before class All students are required to attend class and be prepared to speak on TUESDAY & THURSDAY

This approach comprises the following three activities: (i) the provision of DSMLs , oriented to provide the Domain-Specific Markup Languages (DSMLs), (ii) the authorship

This thesis explores the integration of technology into the teaching process, and further seeks to investigate the relationship between technology integration and the development

Table 6: The results of Pearson correlation coefficient (the relationship between students’ social skills and their entrepreneurship competencies).. Variables

The results from the current study showed that increased suicidal behaviour (SI, past suicide attempts, possible future engagement in suicide) was related to increased

3) Health Authority: The HA plays an important role in our system. It is crucial for our privacy goals to ensure that the HA can not use its special position in the system to