CHANNEL FRAME MIRROR

(1)

AMERICAN SPECIALTIES, INC.

441 Saw Mill River Road, Yonkers, NY 10701 (914) 476.9000 • (914) 476.0688

www.americanspecialties.com

THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE

CHANNEL FRAME MIRROR

MODEL №: 0620

ISSUED: 01/87 REVISED: 19 FEB 2018

SPECIFICATION

Channel Frame Mirror shall have frame fabricated of alloy 18-8 stainless steel, type 304, 20 gauge with mitered corners. Mirror glazing shall be _____(insert glazing option) and shall be warranted for 15 years against silver spoilage. All edges of mirror shall be protected by friction and chafe absorbing fillers. Back of mirror shall be protected by full size shock-absorbing water-resistant filler and full size one piece 20 gauge corrosion protected steel. Top and bottom wall mounting brackets shall be fabricated of 20 gauge corrosion protected steel and shall be spot welded into “H” hanger. Mirror shall be secured to lower bracket with a

Phil-lips Pan Head locking screw.

Channel Frame Mirror shall be Model No_{0620-_____(insert glazing option)________________ (note size, W x H) as}

manufactured by American Specialties, Inc., 441 Saw Mill River Road, Yonkers, New York 10701-4913

MATERIALS

Frame: 18-8, type 304, 20 gauge (.036" <.91mm> thick) stainless steel. Roll-formed one piece construction. Exposed

surfac-es have a No_{4 satin finish. Edges and corners are burr free.}

Glass: Standard glazing is No_{1 quality, 1/4" (6.4mm) thick plate/float, silver coated and hermetically sealed with a uniform}

copper plating, and warranted against silver spoilage for 15 years. Mirrors meet Federal Spec DD-M-411C, ASTM C- 1503, and ASTM C-1036-91.

Filler: Expanded polyethylene microcell foam sheet material, abrasion resistant and shock absorbing, water resistant, 1/8

inch (3.2mm) total layer thickness.

FABRICATION NOTE FOR SPECIFICATION

Mirrors larger than 21sq. Ft. (1.95m2_{) are fabricated in two (2) or more sections to provide installation and handling ease.}

INSTALLATION

Install “H” wall brackets level and plumb per diagram location using ONLY No_{8 or N}o_{10 Pan Head screws (by others). Hang}

mirror on brackets and tighten locking screw (No_{6-32F x 3/4" Philips Pan Head, supplied separately taped to mirror back) at}

bottom (note: this screw should be started prior to hanging mirror on wall bracket). For compliance with 2010 ADA Accessibility Standard, bottom edge of reflecting surface should be no higher than 40" (1016mm) above finished floor.

GLAZING OPTIONS

Units are supplied with 1/4" thick plate glass. Other glazing options are available. For a complete description of any other available glazing, see the MIRROR GLAZING OPTIONS chart.

(2)

www.americanspecialties.com

REVISED: 22 MAY 2014

MIRROR GLAZING OPTIONS

MODEL №:

GLAZINGS

ISSUED: 1-87

NOTES

1. Glazing types indicated are particularly suited to applications where frequent breakage and/or security problems ex-ist. These surfaces are best specified for use in prisons, schools, police stations, hospital wards, etc., where shards of broken glass might possibly be used as weapons.

2. The reflective quality of these mirror types is not as true as plate glass.

3. ASI will not accept returns of these mirror types based upon claims of distortion in reflective properties. GLAZING

SUFFIX DESCRIPTION

A Plate Glass - 1/4" (6.4mm) thick №of electrolytic copper plating. Mirrors meet Federal Spec. №1 quality polished, silver coated and hermetically sealed with a uniform coating DD-M-411C, ASTM C-1503 and ASTM-C-1036-91. Image quality: Excellent

B (1,2,3)

Tempered Glass - 1/4" (6.4mm) thick polished tempered glass with two coats of silver applied. Electroplating with a heavy uniform coating of copper hermetically seals the silver. Back of mirror is finished and protected with a thick coat of heavy waterproof paint. Glazing meets Federal Specification №DD-G1403B, Amendment 1, ASTM C-1503 and ASTM-C-1048-92. Image quality: Good

C

(1,2,3) Metal Mirrors - Shall be Type 304 alloy 18-8 stainless steel, 20 gauge polished to a №Image quality: Good 8 mirror finish.

D

(1) Lexan Dura-Mirror - 1/4" (6.4mm) thick polycarbonate sheet, highly impact resistant. Mirror face is provided with a thick removable masking to prevent scratching during installation. Image quality: Very Good

E

(1) Plexiglas

®_{- Shall be 1/4"}_{(6.4mm) thick acrylic plastic, lightweight and highly shock resistant.} Image quality: Very Good

L (1)

Mirror is fabricated with an interlayer of 1/32" (.8mm) thick vinyl bonded between two 1/8" (3mm) thick sheets of № 1 quality polished plate glass with back silver coated and hermetically sealed with a uniform coating of electro-lytic copper plating. Back of mirror is finished and protected with a thick coat of heavy-duty waterproof paint. Laminated glass meets the performance criteria of Federal Spec. №DD-M-451 and ANSI Z87.1 specifications and complies with CPSC standards 16 CR 1201 (1) 11. Image quality: Excellent

(3)

ISSUED: REVISED: MODEL No:

Accessory Specialties AMERICAN DISPENSER

Desert Ray Products ,INC.

THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE

1-87

SURFACE MOUNTED SHELF

10-06

0692 SERIES

-512 -612 -812 -XX12 12" 6" 2 -516 -616 -816 -XX16 16" 10" 2 -518 -618 -818 -XX18 18" 12" 2 -524 -624 -824 -XX24 24" 18" 2 -530 -630 -830 -XX30 30" 12" 3 -536 -636 -836 -XX36 36" 15" 3 -548 -648 -848 -XX48 48" 14" 4 -560 -660 -860 -XX60 60" 18" 4 -572 -672 -872 -XX72 72" 16-1/2" 5 -5XX -6XX -8XX -XXXX AA" BB" NN 5" depth/length 6" depth/length 8" depth/length specify

depth/length A = length B = spacing Number of brackets SHELF DEPTH & MODEL SUFFIX ADDER SHELF LENGTH DIMENSIONS/BRACKET SPACING

SCHEDULE OF AVAILABILITY

AMERICAN SPECIALTIES, INC.

441 Saw Mill River Road, Yonkers, NY 10701 (914) 476-9000

SPECIFICATION

Surface Mounted Shelf shall be fabricated of alloy 18-8 stainless steel, type 304. Brackets shall be 16 gauge and shelf shall be 18 gauge, with a 1/2" (13) lip on all four (4) sides. Front lip shall be hemmed under for safety. All exposed surfaces shall be No_{4 satin}

finish and shall be protected during shipment with PVC film easily removable after installation. Structural assembly of shelf and bracket supports shall be of welded construction. Shelf shall be sized and brackets located as per standard schedule or shall be custom fabricated to customer supplied drawing. Scheduled shelves equal to or less than 8" (203) deep shall have standard 4" (102) high brackets and shelves in the depth range greater than 8" (203) to 12" (305) shall have 6" (152) high brackets. Consult factory for shelves deeper than 12" (305).

INSTALLATION

Unit is surface mounted on wall or partition using No_{10 (M5) self-tapping screws or other appropriate fasteners (by others) through}

holes provided in support brackets. Ensure that adequate in wall blocking or other reinforcement is provided (by others) to support shelf and intended loading weight. For compliance with ADA Accessibility Guidelines unit should be installed so that shelf top is between 48" (1219) maximum above finished floor (AFF) and 32" (813) minimum AFF. Typical for general utility is 42" (1067) AFF or 18" (457) above washbasin.

OPERATION

Shelf is stable and stationary after proper and secure mounting to adequate wall reinforcement or stud structure. Shelf is suitable for wet (self-contained) or dry materials storage.

Surface Mounted Shelf shall be Model No_{0692-xxx as manufactured by American Specialties, Inc., 441 Saw Mill River Road,}

(4)

HEAVY DUTY STAINLESS STEEL SOAP DISH

0400

AMERICAN SPECIALTIES, INC.

441 Saw Mill River Road, Yonkers, NY 10701 (914) 476-9000 _01-87

12-06

Accessory Specialties AMERICANDISPENSER

SPECIFICATION

Heavy Duty Stainless Steel Soap Dish for dry wall mounting shall be formed of 20 gauge alloy 18-8 seamless deep drawn stainless steel, type 304. Exterior shall have polished bright finish. Retaining lip with rounded corners shall be welded to body and shall project 5/8" (16) from bezel. Optional mounting clamp shall be fabricated of 18 gauge corrosion protected steel with mounting holes for No_{8-32-UNC-2A machine screws (by others). Water runoff path shall be provided as pattern of raised}

dimples on soap shelf and shall prevent soap from slipping.

Heavy Duty Stainless Steel Soap Dish shall be Model No_{0400 of American Specialties, Inc., 441 Saw Mill River Road, Yonkers,}

New York 10701-4913 INSTALLATION

For Standard Recessed Mounting

Use two (2) No_{8 stainless steel Philips flat or oval head self tapping or wood screws (by others) of suitable length to penetrate}

blocking in back of RWO by approximately 1/2" (13). Apply a continuous bead of silicone sealant (by others) behind flange. Tighten screws to hold flange tight against finished wall face. Wipe off excess sealant immediately.

Optional Method for Recessed Mounting

Order separate item Model No_{40 dry wall clamp. Loosely attach clamp to the back of the unit with two (2) stainless steel Philips}

flat or oval head No_{8-32-UNC-2A machine screws (provided by others to suit wall conditions). Apply a continuous bead of}

silicone sealant (by others) behind flange. Insert into RWO and adjust clamp so that it grips inside wall surface through opening. Secure accessory to clamp and wall by tightening screws. Wipe off excess sealant immediately.

Rough Wall Opening (RWO) required is ………6-1/8" W x 4-1/8" H x 4" D (156 x 105 x 102) OPERATION

Raised dimples on the soap shelf allow water to drain away and provide gripping surface to retain soap.

7-1 8" [181] 5" [127] 5-9 16" [141] FRONT VIEW 3" [76] DIMPLED HOLES FOR DRY WALL MOUNTING 3-5 8" [92] RETAINING LIP FINISHED WALL 2-3 4" [70] OPTIONAL MOUNTING CLAMP P/N 40 SIDE VIEW NOTE: DIMS ARE

(5)

COMPACT RECTANGULAR PHENOLIC FOLD-UP SHOWER SEAT (PAGE 1 OF 2)

MODEL №:

8203

ISSUED: 01/87

REVISED: 18 NOV 2016

SPECIFICATION

Rectangular Phenolic Fold –Up Shower Seat shall have all metal parts fabricated of 18-8 alloy type 304 stainless steel.

Seat frame and support legs shall be 1" diameter [Ø25] and 1-1/4" [32] square x 18 gauge [1.2] with 3/16" [4.8]

mounting flanges and 16 gauge [1.5] guide bracket/arm support. All exposed surfaces shall have satin finish. Seat

shall be 5/16" [8] thick phenolic with white color top and bottom surfaces and shall have black edges. Structural

assembly shall be of welded construction and all exposed edges and corners shall be radiused and/or deburred.

Support arm shall fold up when in retracted position to provide low profile against wall. No extra fittings shall be

required to retain seat in storage position. Guide bracket shall control seat lowering into operating position. Unit shall

satisfy 2010 ADA Accessibility Standards when mounted properly.

Rectangular Phenolic Fold-up Shower Seat shall be Model N

o

_{8203 as manufactured by American Specialties,}

Inc., 441 Saw Mill River Road, Yonkers, NY 10701-4913

INSTALLATION

This unit is surface mounted. Installer/construction contractor must provide concealed anchor plate or blocking as

specified in construction documents or as required by local building codes prior to wall finishing. Fasten unit flanges

and guide bracket to concealed anchor or blocking plate with appropriate hardware. See "STRENGTH" section

below. Note that concealed mounting plates or anchors and hardware are not supplied with this product and must be

specified separately. Ensure that mounting configuration complies with local building codes. Waterproof all fasteners

during installation process.

(6)

COMPACT RECTANGULAR PHENOLIC FOLD-UP SHOWER SEAT (PAGE 2 OF 2)

MODEL №:

8203

ISSUED: 01/87

REVISED: 18 NOV 2016

STRENGTH

ASI Shower Seats are designed in standard sizes to meet and exceed 2010 ADA Accessibility Standards and ANSI

A117.1 that fabricated product shall be of adequate strength to support a load of 250 lbs. (113.4 kg) and unit shall

conform to size and edge clearances as diagrammed. Non-standard sizes should be carefully evaluated for compliance.

Mounting to the wall is a critical part of the system to meet this requirement. To withstand the shear, tension or

pullout, and torsion loads generated by the maximum loading, the fastener system must be adequately sized. Unit will

carry a load of 500 lbs. (227 kg) if properly installed. The supporting wall must be adequately reinforced to carry the

rated load for the products lifetime.

MATERIALS

Tube: 18 gauge (.048" [1.22] thick) type 304 stainless steel, 1" [Ø25] dia. and 1-1/4" [32] square. Unitized all

welded construction. Exposed surfaces are satin finish. Edges and corners are radiused and burr free.

Flange: 3/16" [4.8] type 304 stainless steel. Exposed surfaces have satin finish. Edges and corners are radiused and

burr free.

Bracket: 16 gauge (.06" [1.52] thick) type 304 stainless steel. Exposed surfaces are satin finish. Edges and corners

are radiused and burr free.

Seat:

Solid Phenolic 5/16" x 14-5/8" x 18" [8 x 371 x 457]. Exposed surfaces have semi-gloss laminate white top

and bottom surfaces and shall have black edges. Corners are radiused, edges are champhered, and burr free.

Seat top shall have three [3] slots 1/4" wide x 12" long [6 x 305] for water drainage and user slip resistance.

Mounting hardware is stainless steel dome head carriage bolts with acorn nuts on bottom.

Spring: Stainless steel wire type 304 OD 27/32" [Ø21.6] coils x 2-1/4" body length [57.2] x .085" [Ø2.2] wire

diameter.

OPERATION

Fold-up Shower Seat requires only one hand operation to manually lower to horizontal position for use or raise for

departure and arrival. Guide bracket with spring detent prevents seat from dropping and provides positive support

in usage position as well as spring locked storage position.

(7)

1-1/2" DIAMETER [Ø38] GRAB BAR SERIES WITH SNAP-ON FLANGE COVERS

MODEL №:

3800

ISSUED: 01/87

REVISED: 7 MAR 2017

SPECIFICATION

1-1/2" Diameter [Ø38] Grab Bar with Snap-On Flange Covers for concealed mounting shall be type 304 stainless

steel alloy 18-8. Tubing shall be 1-1/2" diameter [Ø38] x 18 gauge (0.048") [1.2]. Snap-on cover shall be 22 gauge

(0.03") [0.8]. Flange shall be 1/8" [3] thick and shall be heliarc welded to tubing with a continuous concealed

bead. End flanges shall have two (2) 5/16" diameter [Ø7.5] mounting holes. Center posts (if any) shall have (2)

keyhole slots to ease installation access. All exposed surfaces shall have a satin finish and shall be protected

during shipment with a plastic bag. For optional non-slip surface add suffix –P (peened).

1-1/2" Diameter [Ø38] Grab bar with Snap-On Flange Covers shall be Series № 3800 of American

Specialties, Inc., 441 Saw Mill River Road, Yonkers, New York 10701- 4913

STRENGTH

ASI Grab Bars are designed to meet and exceed ADA requirements as published in CABO/ANSI A117.1 and

2010 ADA Accessibility Standards. Mounting to the wall is a critical part of the system to meet this requirement.

To withstand the shear, tension or pullout, and torsion loads generated by the maximum loading, the fastener

system must be adequately sized.

INSTALLATION

Use grab bar as template to mark mounting holes locations and pre-drill holes. Install bar using two (2) № 10

self-tapping pan head screws and flat washers (by others) or other fastener system (by others) to suit conditions for

each flange. Appropriate anchoring and backing must be provided in accordance with local building codes or as

specified on Architects Plans prior to wall finishing. For compliance with 2010 ADA Accessibility Standards,

install unit so that the top of the grab bar is 33" [840] minimum above finished floor (AFF) to 36" [915] maximum

AFF. Anchors are available from ASI and must be specified separately for each grab bar style scheduled (see 3900

series).

(8)

441 Saw Mill River Road, NY 10701 (914) 476.9000 • (914) 476.0688 www.americanspecialties.com

GRAB BAR CONFIGURATIONS (PG 1 OF 3)

MODEL

№:

GRABBAR CONFIG

ISSUED: 09/96 REVISED: 02/12

SCHEDULE

QTY. DIM. A QTY. DIM. A 12" [305] 36" [914] 18" [457] 42" [1067] 24" [610] 48" [1219] 30" [762] SCHEDULE QTY. DIM. A 52" [1321] 54" [1372] 60" [1524] 72" [1829]

TYPE -01

TYPE -02

TYPE -04

TYPE -15

SCHEDULE QTY. HAND LH RH LH SHOWN RH OPPOSITE

MODEL № MUST SPECIFY -LH OR -RH 33" [838] 30" [762] 3" [76] PROJECTION BELOW FINISHED FLOOR

CONTRACTOR TO PROVIDE PROPER SLEEVE IN FLOOR X 3" LONG TO ACCEPT BAR OD SPECIFIED. 28" [711] 32" [813] 16" [406] 90° 1-1/2" [38] ALL DIMS INCH [MM] A 23 FEB 2015

(9)

GRAB BAR CONFIGURATIONS (PG 2 OF 3)

MODEL

№:

GRABBAR CONFIG

ISSUED: 09/96 REVISED: 02/12 18" [457] 27" [686] 6" [152] 33" [838] FINISHED FLOOR FINISHED WALL SCHEDULE

QTY. DIM. A QTY. DIM. A

12" [305]* 36" [914] 18" [457]* 42" [1067] 24" [610] 48" [1219] 30" [762] 54" [1372] * No center support

TYPE -24

TYPE –33

TYPE -34

TYPE –75

SCHEDULE QTY. HAND LH RH RH SHOWN LH OPPOSITE

MODEL № MUST SPECIFY LH OR -RH 1-1/2" [38] ALL DIMS INCH [MM] 30" [762] 33" [838] 12" [305] 5" [127]

FOR BEDPAN FLUSH VALVE USE 24" [610] 24" [610] 18" [456] 5" [127] 5" [127] 1" [25] 23 FEB 2015

(10)

GRAB BAR CONFIGURATIONS (PG 3 OF 3)

MODEL

№:

GRABBAR CONFIG

ISSUED: 09/96 REVISED: 02/12 SCHEDULE QTY TYPE A B C 50 24" [610] 36" [914] 29-3/4" [756] 56 36" [914] 54" [1372] 47-3/4" [1213] 57 42" [1069] 54" [1372] 47-3/4" [1213] 60 18" [457 ] 30" [762 ] 23-3/4" [603] 74 18-1/8" [460] 33-1/8" [841] 26-7/8" [683]

Option -25 Toilet Paper Holder is welded on to Grab Bars of the Swing Up or Swing Away configurations 3413, 3451, 3454 and Fixed Types -15, -33

OPTION –25

A C B 6-1/4" [159] 1-1/2" [38] FACE OF WALLS SEE G R AB BA R SEE GRAB BAR 3-3/4" [95]

FOR TYPES -15 & -33

2-3/4" [70] FOR TYPES -13, -14, -51 & -54 4-3/4" [121] 12" [305]

TOILET PAPER HOLDER FORMED OF 1

4" DIA [Ø6.4]

SOLID SS 304 ROD WELDED TO GRAB BAR

(11)

1-87

DOUBLE ROBE HOOK

1-06

7345

AMERICAN SPECIALTIES, INC.

SPECIFICATION

Double Robe Hook shall be fabricated of stainless steel alloy 18-8, type 304. Post shall be 1/2" x 1" (13mm x 25mm) rectangular tubing with formed mounting flange and bracket welded on end. Bow plate shall be 14 gauge, 4" x 1" (102mm x 25mm) with radiused corners and internally welded to outer end. Mounting plate shall be included and shall be 18 gauge. A stainless steel setscrew shall be provided on bottom perimeter of flange to lock unit to mounting plate. Surface finish shall be bright or satin as chosen by option and indicated by code suffix.

Double Robe Hook shall be Model No_{7345-B or N}o_{7345-S of American Specialties, Inc., 441 Saw Mill River Road,}

Yonkers, New York 10701-4913 INSTALLATION

Surface mount unit on door back or wall using No _{10 self tapping screws (by others) through holes provided in mounting plate}

into suitable prepared mountings (by others) or other suitable mounting hardware (by others) to suit door or wall conditions. Hang post and flange assembly on mounting plate and tighten setscrew to lock unit to plate. For compliance with ICC/ANSI A-117.1-2003 and ADA Accessibility Guidelines install unit with top of hook 48" (1219mm) maximum above finished floor (MAX AFF) if clear floor forward reach or if clear floor side reach access only is provided or 46" (1168mm) MAX AFF if side reach access over an obstruction (e.g. vanity) with reach depth greater than 10" (254mm) and less than 25" (635mm) is only provided or 44" (1118mm) MAX AFF if forward reach over an obstruction with reach depth greater than 20" (508mm) and less than 25" (635mm) is only provided. For general utility install hook with centerline of mounting plate 68" (1727mm) AFF.

OPERATION

(12)

441 Saw Mill River Road, NY 10701 (914) 476.9000 • (914) 476.0688 www.americanspecialties.com 13" [330] 17-1 4" [438] 6-1 2" [165] 11" [279] 1" [25] 2-3 16" [56] 2-11 16" [68] 1 2" [13] INTERNATIONAL GRAPHIC SYMBOL FINGER GRIP 1 4"DIA [Ø6] DIMPLED MOUNTING HOLES 1" [25] 1 4" [6] 4" [102] ADJUSTABLE FROM 1 2" TO 3" [13 TO 76] THICK PARTITION 15-1 4" [387] FIXED FLANGE REMOVEABLE WASTE RECEPTACLE FOR PROPER INSTALLATION IN CABINET ENGAGE HOOK IN REAR NOTE: ALL DIMS INCH [MM]

PARTITION MOUNTED DUAL ACCESS SANITARY NAPKIN DISPOSAL

MODEL

№: 0472

ISSUED: 01/87 REVISED: 07/10

SPECIFICATION

Partition Mounted Dual Access Sanitary Napkin Disposal shall hold 1.5 gal (5.7 L) of dry/solids waste. Doors, flanges, waste receptacle and cabinet shall be 22 gauge type 304 stainless steel alloy 18-8. All exposed surfaces shall be satin finish and be pro-tected during shipment with PVC film easily removable after installation. Doors shall operate independently and shall be attached to cabinet with a full-length 3/16" diameter (Ø4.8) stainless steel multi-staked piano hinge and shall be spring loaded to hold in closed position. International graphic symbol for waste disposal label shall be adhered to doors. Structural assembly of body and door components shall be of welded construction. Face trim mounting flanges shall be of one piece construction 1" (25) wide with no welded miters and shall have square 1/4" (6) returns with an adjustability range for partition thickness of 1/2" (13) to 3" (76). Waste container shall be captured internally by full width Ζ-retainer and shall have fully hemmed-finger grip for safety and ser-vice removal from one side only.

Partition Mounted Dual Access Sanitary Napkin Disposal shall be Model № 0472 as manufactured by American Special-ties, Inc., 441 Saw Mill River Road, Yonkers, New York 10701-4913

INSTALLATION

Partition mount unit through precut partition cutout (PCO) using four (4) № 10 x 3/4" (M5 x 20) Philips flat head or oval head self tap-ping screws (supplied) per side (eight [8] total) through mounting holes provided through fixed mounting frame and adjustable mount-ing frame into suitably prepared partition (by others). Mountmount-ing holes are offset 1/2" (13) from opposite side frame holes for screw clearance. Note that cutout is 3/16" (Ø4.8) above cabinet door top and 13/16" (21) below mounting flange top edge. Mounting flanges adjust to accommodate partition thickness of 1/2" (13) minimum to 3" (76) maximum. For compliance with ADA Accessibility Guidelines and maximum usability install unit with top of disposal door 33" (864) MAX AFF and 24" (610) min AFF and 27" (686) to centerline of cutout from rear wall.

PCO Required is 11-3/8" W x 15-5/8" H x 1/2" to 3" Thick (289 x 397 x 13 to 76) OPERATION

Users push doors to deposit waste material. Doors are self-closing and operate independently and may be used simultaneously. Maintenance schedule determines waste removal cycle. Empty unit by removing bottom waste container and inverting over col-lection bag. Waste container is captured by internal angle to prevent inadvertent dumping. Safety-edged finger grip provides con-venient lift handle for service.

(13)

1-87

0473

9-04

RECESSED SANITARY NAPKIN DISPOSAL

SPECIFICATION

Recessed Sanitary Napkin Disposal shall hold 1.5gal (5.7 liters) of dry solids. Upper door, waste container and cabinet frame shall be fabricated of alloy 18-8 stainless steel, type 304, 22 gauge. Structural assembly of body and door components shall be of welded construction. Upper door shall be hung on cabinet with a stainless steel spring hinge and have the international waste symbol on face. All exposed

surfaces shall have a No_{4 satin finish and be protected during shipment with a PVC film that shall be easily removable after installation.}

Face trim shall be of one piece construction 1" (25.4mm) wide with no welded miters and shall have square 1/4" (6.35mm) return to wall..

Recessed Sanitary Napkin Disposal shall be Model No_{0473 as manufactured by American Specialties, Inc., 441 Saw Mill River}

Road, Yonkers, New York 10701-4913 INSTALLATION

Unit is mounted in wall recess using No _{10 self tapping screws (by others) through concealed mounting holes provided. Note that top of}

rough wall opening is 3/4" (19mm) below top of unit.

Rough Wall Opening required is…………..11-1/4" W x 15-3/4" H x 4" D. minimum (286mm x 400mm x 102mm) OPERATION

Users push door to deposit waste material. Door is self-closing. Unit is emptied by removing can and removing disposable waxed waste paper bag which is furnished by others. Waste container is held in place by a "Z" clip retainer to prevent inadvertent dumping of contents. Safety-edged finger grip provides convenient grip for service.