1 ODX302015 CX600-X 1. Series Products Hardware Introduction ISSUE 1

(1)

CX600-X Series

Products Hardware

Introduction

www.huawei.com

(2)

Foreword

CX600-X is a high-end router designed for core and

backbone networks. The CX600-X is positioned as the edge

or convergence router on the IP backbone network.

Based on the powerful Versatile Routing Platform (VRP),

the CX600-X features the following: rich services, large

capacity, high performance, high availability.

(3)

Objectives

Upon completion of this course, you will be able to:

Describe CX600-X hardware system architecture

Describe CX600-X boards

Describe CX600-X performance parameters

CX600-X chassis and boards

(4)

1. CX600-X16/X8/X3 Hardware Introduction

2. CX600-X2/X1 Hardware Introduction

(5)

1. CX600-X16/X8/X3 Hardware Introduction

2. CX600-X2/X1 Hardware Introduction

(6)

1. CX600-X16/X8/X3 Hardware Introduction

1.1 CX600-X16 Chassis

1.2 CX600-X8 Chassis

1.3 CX600-X3 Chassis

1.4 CX600-X16/X8/X3 Boards

(7)

Overview-Appearance of CX600-X16

①

③

②

④

⑤

⑥

⑧

⑦

⑧

Switching capacity: 12.58T(bidirectional)

Interface capacity

：

3.2T (bidirectional)

MPU 1 : 1 redundancy

SFU 3

＋

1 redundancy

FAN2

＋

2 redundancy

A Power Entry Modules (PEMs)

Working in 4+4 load balancing mode

4 ＋

4 redundancy

③

⑤

①

⑥

⑦

⑧

⑨

④

No. _Module Quantity

① Air intake vent × 2

② MPU × 2 ③ SFU × 4 ④ LPU × 16 ⑤ Cabling trough × 2 ⑥ Fan module × 4 ⑦ Filtering box × 4 ⑧ DC power module × 8 ⑨ CMU × 1

(8)

Overview-Distributed Architecture

1

2

3

17

18 L

P

U

SFU

4

5

6

7 L

P

U

L

P

U

M

P

U

M

P

U

L

P

U

L

P

U

L

P

U

L

P

U

19

20 L

P

U

SFU

8

9

10

11

12

13

14

15

16 L

P

U

L

P

U

L

P

U

L

P

U

L

P

U

L

P

U

L

P

U

L

P

U

20

21

22

(9)

Power Supply System

The CX600-X16 supports either DC or AC

power supply.

In the case of a DC power supply system, eight 70 A

Power Entry Modules (PEMs) are inserted at the rear of the chassis, working in 4+4 load balancing mode.

In the case of an AC power supply system, two AC

power frames are placed outside the chassis and installed with rectifier modules based on system

power. The AC power frames are then connected to the input terminals on the DC-PEMs to supply power for the system. (In short, external AC power frames are added to the DC power supply system to

constitute an AC power supply system).

The CX600-X16 backplane is divided into

four areas, with each area having two

power inputs. These eight power inputs

work in backup mode.

(10)

Power Supply System-DC Power Supply

System

Indicator Color

Description

RUN

Green

Indicates normal power output. If the indicator is

steady on, it implies the normal output.

ALM

Red

Power failure indicator. If the indicator is steady

on, it indicates the following:

Lightning-proof circuits on the power module become faulty.

module become faulty.

One of the power modules does not have input power.。

Note : If the CX600-X16 has a DC power supply system,

eight 70 A PEMs work in 4+4 backup mode. Two -48V power

inputs are joined on the board. After the low-frequency

filtering, the two -48 V power inputs for fans are joined inside

the fan module.

(11)

Power Supply System-Architecture of DC

Power Supply System

(12)

Power Supply System-AC Power Supply

System

Front view of the AC rectifier module:

Rear view of the AC rectifier module

Name

Color

Status

Error status

Error reasons:

Power

running

Indicator

Green

On

Off

Electricity supply error(no electricity input、lower voltage )、no output from the power modules.

Protection

Indicator

Yellow

Off

On

Temperature Alarm( exceed 65 ℃ to Over-temperature Shut-down ) ; Dormancy Shut-down (only indication from the indicator, no report)

Failure

Indicator

Red

Off

On

Overvoltage shutdown、FANs error、 Over-temperature Shut-down、errors in power module

(13)

Power Supply System-Architecture of AC

Power Supply System

Area 1

board

Filter box

Area 2

L P U 0 L P U 1 L P U 2 M P U 0 M P U 1 L P U 3 L P U 1 L P U 1 L P U 1 area1 area2 DCa1 DCb1 DCa2 System board AC1 AC2 DCa

SFU 0 SFU 1 SFU 2 SFU 3 LP U 7 LP U 8 LP U 9 LP U 10 LP U 11 LPU1 2 LP U 13 LPU 14 LP U 15

Area 4

board

Filter box

Area 3

area2 area3 area4 DCa2 DCb2 DCa3 DCb3 DCa4 DCb4 DCb DCa

(14)

Heat Dissipation System-Fan

Rear CX600-X16 Air Flow Map

X16: the air channels for upper and lower frames are independent and dissipate heat separately.

Fan modules locate at the rear of the chassis, and the exhaust design is evenly

Fan 2

＋

2 redundancy

“ U” shape air-flow channel, helpful for evenly Heat Dissipation, avoiding dead angle

(15)

Heat Dissipation System- Air Filter

Air filter

：

SFU Area Air filter:

(16)

Switching Network

100Gbps Switching Network

B(SFUI-100-B)

：

200Gbps Switching Network B(SFUI-200-B)

：

LED

Indictor

RUN

Before the registration of the SFU: If the indicator blinks twice every second (2 Hz), the

system is in the alarm state.

After the registration of the SFU: If the indicator blinks once every two seconds (0.5 Hz),

the system is running normally.

ACT

If the indicator is on, it indicates that the SFU is working normally; if the green indicator

is off, it indicates that the SFU is faulty.

OFL

When the SFU is working normally, the OFL indicator is off. After the OFL button is

(17)

Switching Network Appearance

The CX600-X16 has 4 SFUs. These 4 SFUs work in 3+1 load balancing mode. The

4 SFUs load balance services at the same time. When one SFU is faulty or being

replaced, the other 3 SFUs automatically take over its tasks to ensure normal

delivery of services, thus improving system reliability.

(18)

Control Plane

The control plane of the CX600-X16 is separated from the data plane and the

monitoring plane.

MPU is responsible for management and controlling including route calculating,

monitoring and maintenance.

Main processing module, clock module and LAN Switch all use 1:1 hot

redundancy

The two MPUs work in 1:1 backup mode. Each MPU monitors the status of the

other. If the master SRU is faulty, the slave MPU automatically takes over as the

master MPU.

(19)

1. CX600-X16/X8/X3 Hardware Introduction

1.1 CX600-X16 Chassis

1.2 CX600-X8 Chassis

1.3 CX600-X3 Chassis

1.4 CX600-X16/X8/X3 Boards

(20)

Overview-Appearance of CX600-X8

①

②

⑥

No. Module Quantity

① Air intake vent × 1

Switching capacity: 7.08T(bidirectional)

Interface capacity

：

1.6T (bidirectional)

SRU 1

：

1 redundancy

SFU2

＋

1 redundancy

FAN1

＋

1 redundancy

A Power Entry Modules (PEMs)

Working in 2+2 load balancing mode

③

④

⑤

⑦

⑧

⑦

⑧

⑨

① Air intake vent × 1 ② SRU × 2 ③ SFU × 1 ④ LPU × 8 ⑤ Cabling trough × 1 ⑥ Fan module × 2 ⑦ Filtering box × 2 ⑧ DC power module × 4 ⑨ CMU × 1

(21)

Overview-Slot Layout

1

2

3

4

9

11

5

6

7

8 L

P

L

P

L

P

L

P

S

R

S

F

L

P

L

P

L

P

L

P

10 S

R

P

U

P

U

P

U

P

U

R

U

F

U

P

U

P

U

P

U

P

U

R

U

1

2

3

4

9

11

10

5

6

7

8

(22)

Power Supply System

The CX600-X8 supports either DC or AC

power supply.

In the case of a DC power supply system, four 70 A

Power Entry Modules (PEMs) are inserted at the rear of the chassis, working in 2+2 load balancing mode.

In the case of an AC power supply system, an AC In the case of an AC power supply system, an AC

power frame is placed outside the chassis and installed with rectifier modules based on system power. The AC power frame is then connected to the input terminals on the DC-PEMs to supply power for the system. (In short, an external AC power frame is added to the DC power supply system to constitute an AC power supply system.

)

The CX600-X8 backplane is divided into two

areas, with each area having two power inputs.

These four power inputs work in backup mode.

(23)

Power Supply System-DC Power Supply

System

Indicator

Color

Description

RUN

Green

Indicates normal power output. If the

indicator is steady on, it implies the normal

output.

ALM

Red

Power failure indicator. If the indicator is

steady on, it indicates the following:

Lightning-proof circuits on the power

module become faulty.

One of the power modules does not

have input power.

Note : If the CX600-X8 has a DC power supply system, four 70

A PEMs work in 2+2 backup mode. Two -48V power inputs are

joined on the board. After the low-frequency filtering, the two -48

V power inputs for fans are joined inside the fan module.

(24)

Power Supply System-Architecture of DC

Power Supply System

(25)

Power Supply System-AC Power Supply

System

Front view of the AC rectifier module

Rear view of the AC rectifier module

Name

Indictor

Status

Error Status

Error reason

Power running Indicator

Green

On

Off

Electricity supply error(no electricity input

、

lower

voltage )

、

no output from the power modules.

Protection Indicator

Yellow

Off

On

Temperature Alarm( exceed 65 ℃ to

Over-temperature Shut-down ) ; Dormancy Shut-down

(only indication from the indicator, no report)

Failure Indicator

Red

Off

On

Overvoltage shutdown

、

FANs error

、

Over-temperature Shut-down

、

errors in power module

(26)

Power Supply System-Architecture of

AC Power Supply System

(27)

Heat Dissipation System-Fan

Rear CX600-X8 Air Flow Map

flow channel, helpful for evenly Heat Dissipation, avoiding dead angle.

Fan modules locate at the rear of the chassis, and the exhaust design is evenly

Fan 1

＋

1 redundancy

(28)

Heat Dissipation System-Air Filter

Air Filter

：

Note:

Placing a black sponge air filter at the air intake vent helps to prevent dust from

entering the system. It is recommended that air filters be removed and cleaned

at least once every three months.

(29)

SFU

100Gbps SFUC(SFUI-100-C)

200Gbps SFU C(SFUI-200-C)

LED

Description

RUN

Before the registration of the SFU: If the indicator blinks twice every

second (2 Hz), the system is in the alarm state.

After the registration of the SFU: If the indicator blinks once every two

seconds (0.5 Hz), the system is running normally.

ACT

If the indicator is on, it indicates that the SFU is working normally; if the

green indicator is off, it indicates that the SFU is faulty.

OFL

When the SFU is working normally, the OFL indicator is off. After the

OFL button is pressed to power off the SFU, the OFL indicator is on.

(30)

Switching Network Appearance

(31)

Control Plane

The control plane of the CX600 is separated from the data plane and the

monitoring plane. The SRU is used by the CX600-X8.

The two SRUs work in 1:1 backup mode. Each SRU monitors the status

of the other. If the master SRU is faulty, the slave SRU automatically

takes over as the master SRU.

(32)

1. CX600-X16/X8/X3 Hardware Introduction

1.1 CX600-X16 Chassis

1.2 CX600-X8 Chassis

1.3 CX600-X3 Chassis

1.4 CX600-X16/X8/X3 Boards

(33)

Overview-Appearance

Interface capacity

：

240G(bidirectional)

Switching capacity : 1.08T(bidirectional)

Appearance of the CX600-X3 DC chassis

MPU 1

：

1redundency

Fan 1

＋

1 redundancy

Page32

(34)

Overview-Slot Layout

LPU

MPU

1

2

3

5

4 Slot layout

Slot Number

Quantity Slot Width

Remarks

1 ～

3

3 41mm

（

1.6 inches)

These slots are used to hold

LPUs.

4 ～

5

2 41mm

（

1.6 inches)

These slots hold MPUs that

work in 1:1 backup mode.

Page33

(35)

Power Supply System

The CX600-X3 supports either DC or AC

power supply.

Power modules convert the input voltage into

-48 V DC voltage to supply power for the

entire system. The power supply system has

the following features:

The power supply system consists of two

AC power modules or two DC power

modules working in 1+1 backup mode.

Both AC power modules and DC power

modules support alarm functions. DC

power modules support I2C

communications and AC power modules

support RS485 communications.

Two AC power modules or two DC power

modules work in 1+1 backup mode to

improve the reliability of power supply.

(36)

Power Supply System-DC Power Supply

System

Note

：

Note

：

The PEM of the CX600-X3 is 1 U.

The indicator of DC power supply module in CX600-X3 is located at the

panel of the power module.

The power supply module in CX600-X3 has one input and following

functions:

Surge protection, filtering, and short circuit protection

Alarm

(37)

Power Supply System-AC Power Supply

System

Note

：

The PEM of the CX600-X3 is 1 U.

The AC power supply module has various protection functions,

including:

Outgoing overvoltage protection

Short circuit

Alarm

(38)

Heat Dissipation System -Fan

Air flow in the CX600-X3 DC chassis(DC)

The CX600-X3 draws in air from the left

and exhausts air from the rear. The air

intake vent is located at the left side of

the chassis and the air exhaust vent is

located at the rear of the chassis.

Fans are back-to-back and two fans in

Air flow in the CX600-X3 AC chassis

Fans are back-to-back and two fans in

the frame.

The heat dissipation system consists of

the following components:

One fan module

An air intake vent and an air exhaust vent

An air filter

(39)

Heat Dissipation System - Air Filter

Note

：

The air filter of the CX600-X3 is located on the left rear of the

chassis .

The air filter of the CX600-X3 can be bent, which facilitates the

maintenance within a limited space in the rear of the chassis.

(40)

1. CX600-X16/X8/X3 Hardware Introduction

1.1 CX600-X16 Chassis

1.2 CX600-X8 Chassis

1.3 CX600-X3 Chassis

1.4 CX600-X16/X8/X3 Boards

(41)

CX600-X16/X8/X3 Boards

CX600-X16/X8/X3 support boards:

LPU

LPUF-100,4 Sub-slots ,supports L3VPN and MVPN (Not for CX600-X3)

LPUI-100 (Not for CX600-X3)

LPUF-40,2 Sub-slots

LPUI-40

LPUI-41

LPUS-41

LPUS-20

LPUF-21,2 Sub-slots

LPUF-10,4 Sub-slots

Page40

(42)

Service Process Unit- Versatile Service

Process Unit C

SPUC Supports NetStream

、

GRE and Multicast VPN

without any physical interface and fit for any LPU.

(43)

Service Process Unit- Flexible Card Versatile

Service Unit 10(VSUF-10)

The VSUF-10 is of a multi-core processing architecture and has a

high-performance multi-core processing engine and a large memory. The

board provides flexible and complicated service processing capabilities

and ensures bandwidth for the user traffic with a large throughput.

Software features

FCC

RET

MDI

Hardware features

Supporting hot swap

(44)

Service Process Unit- Integrated Versatile

Service Unit 20 A(VSUI-20-A)

The VSUI-20-A, also known as the CR5DVSUI201A, provides the

following functions:

：

Encrypts user data to ensure data secrecy.

Checks data completeness to ensure that the data is not modified when being transmitted.

Prevents anti-replay of data by means of a sequence number and prevents middleman

attack by means of authentication.

Supports negotiations of security algorithms and keys between devices and provides a

secure mechanism for online key generation.

Supports two security modes, that is, transport mode and tunnel mode, to meet

(45)

Flexible Card Line Processing Unit(LPUF-100)

The LPUF-100 provides four slots .An FPIC supports the following

functions:

Hot swap

Automatic recovery of configurations

Intermixing with other types of FPICs

LPUF-100 Software features:

NSF

FRR

(46)

LPUF-100 Supporting Subcards

24-Port100/1000Base-SFP Flexible Card

48-Port 100/1000Base-CSFP Flexible Card

(47)

Flexible Card Line Processing

Unit(LPUI-100)(1/2)

10-Port10GBase LAN/WAN-XFP supports1588v2

Software features

IPv4 and IPv6 address

ICMP

L3 routing protocol

（

BGPv4

、

OSPFv2

、

OSPFv3

、

IS-IS

）

Multicast protocol

（

PIM-SM

、

Bidir-PIM

、

PIM SSM

、

AutoRP

）

(48)

Flexible Card Line Processing

Unit(LPUI-100)(2/2)

16-Port10GBase LAN-SFP + Flexible Card Line Processing Unit

(LPUI-100)

Function

IEEE 802.3ae

IEEE 802.3x Flow Control

IEEE802.1q Jumbo frames supported by VLAN

IEEE802.3ad Link aggregation

IEEE 802.1p Label

(49)

Flexible Card Line Processing

Unit(LPUF-40)

The Flexible Card Line Processing Unit LPUF-40 provides two slots, each

of which can hold an FPIC that supports hot swapping. The cards support

hot swap. The LPUF-40 supports a maximum of 40-Gbit/s bandwidth.

The LPUF-40 has two models: LPUF-40-A and LPUF-40-B.

Software features

LPUF-40-A supports all software features

LPUF-40-B does not support L3VPN, MVPN, or IPv6., IPv6

Hardware features

LPUF-40 supports hot swap.

The FPIC of the LPUF-40 supports hot swap.

(50)

LPUF-40 Supporting Subcards(1/2)

20-Port100/1000Base-X-SFP

Flexible Card A(supports1588v2)

20-Port 100/1000Base-X-SFP Flexible Card

20-Port10/100/1000Base-RJ45 Flexible Card

20-Port100/1000Base-X-SFP Flexible Card B

(51)

LPUF-40 Supporting Subcards(2/2)

2-Port 10GBase LAN/WAN-XFP

Flexible Card A(supports1588v2)

2-Port 10GBase LAN/WAN-XFP Flexible Card

Flexible Card A(supports1588v2)

4-Port 10GBase LAN/WAN-XFP Flexible Card

2-Port 10GBase LAN/WAN-XFP Flexible Card B

(52)

Integrated Line Processing Unit (LPUI-40)(1/2)

4-Port 10GBase LAN/WAN-XFP Integrated Line Processing

Unit (LPUI-40)

Function

IEEE 802.3ae

IEEE 802.3x Flow Control

IEEE802.1q VLAN Jumbo frames supported by VLAN

IEEE802.3ad Link aggregation

IEEE 802.1p Label

(53)

Integrated Line Processing Unit (LPUI-40)(2/2)

40-Port100/1000Base-X-SFP Integrated Line Processing

Unit (LPUI-40)

Function

IEEE 802.3ab

IEEE 802.3z

IEEE 802.3x Flow Control

IEEE802.1q VLAN Jumbo frames supported by VLAN

IEEE802.3ad Link aggregation

IEEE 802.1p Label

(54)

Integrated Line Processing Unit(LPUI-41)(1/3)

Integrated Line Processing Unit (LPUI-41) function feature:

IPv4 and IPv6 address distribution

ICMP

L3 Route Protocol(BGPv4

、

OSPFv2

、

OSPFv3

、

IS-IS )

Multicast Protocol(PIM-SM

、

Bidir-PIM

、

PIM SSM

、

AutoRP )

Multicast Protocol(PIM-SM

、

Bidir-PIM

、

PIM SSM

、

AutoRP )

Page53

(55)

Integrated Line Processing Unit(LPUI-41)(2/3)

4-Port 10GBase LAN/WAN-XFP

Integrated Line Processing Unit

48-Port100/1000Base-X-SFP

Integrated Line Processing Unit

2-Port 10GBase LAN/WAN-XFP+

24-Port 100/1000Base-X-SFP

(56)

Integrated Line Processing Unit(LPUI-41)(3/3)

4-Port 10GBase LAN/WAN-XFP Integrated Line

Processing Unit

(LPUI-41,supports1588v2)

40-Port 100/1000Base-X-SFP Integrated Line Processing Unit

(LPUI-41

，

supports1588v2)

2-Port 10GBase LAN/WAN-XFP+

20-Port 100/1000Base-X-SFP Integrated

Line Processing Unit

（

LPUI-41

，

(57)

Line Processing Unit S(LPUS-41)

8-Port 10GBase LAN/WAN-XFP Line Processing Unit S(LPUS-41)

4-Port10GBase LAN/WAN-XFP Line Processing Unit S(LPUS-41)

48-Port100/1000Base-X-SFP

Line Processing Unit S(LPUS-41)

(58)

Line Processing Unit S(LPUS-20)

4-Port10GBase LAN/WAN-XFP Line Processing Unit S(LPUS-20)

40-Port10/100/1000Base-RJ45 Line Processing Unit S(LPUS-20)

40-Port100/1000Base-SFP

(59)

Flexible Card Line Processing Unit(LPUF-21)

The LPUF-21 provides two slots, each of which can hold one

half-width FPIC.

The LPUF-21 has two models:LPUF-21-A and LPUF-21-B.

Software features

LPUF-21-A supports all software features

LPUF-21-B not support L3VPN, MVPN, IPv6 advanced

Hardware features

LPUF-21 supports Hot swap

FPIC of LPUF-21 support Hot swap

(60)

Flexible Card Line Processing Unit(LPUF-10)

The LPUF-10 provides four slots that can hold full-height

FPICs or four half-height FPICs.

An FPIC supports the following functions:

Hot swap

Automatic recovery of configurations

Intermixing with other types of FPICs

Software features

NSF

FRR

(61)

Self-Test Question About

CX600-X16/X8/X3 Hardware

1. In the CX600-X16/X8/X3 routers, the dynamic routing

protocol is processed by the ( )

A. Clock board

B. Control plane

C. Heat dissipation system

D. Flexible card

(62)

Content

1. CX600-X16/X8/X3 Hardware Introduction

2. CX600-X2/X1 Hardware Introduction

(63)

Content

2. CX600-X2/X1 Hardware Introduction

2.1 CX600-X2/X1 Chassis

2.2 CX600-X2/X1 Board

(64)

Overview-CX600-X2 System Structure

The CX600-X2 provides two slots for NPUs and eight slots for

PICs. The network process unit on the CX600-X2 is NPUI-20. All

the PICs perform data switching through the 20. The

NPUI-20 has a bidirectional processing capability of up to NPUI-20Gbit/s. The

maximum interface capacity of the CX600-X2 is 75.2Gbit/s.

(65)

Overview-CX600-X1 System Structure

The CX600-X1 provides one slot for the NPU and four slots for

PICs. The network process unit on the CX600-X1 is NPUI-20. All

the PICs switch data with each other through the NPUI-20. The

NPUI-20 has a bidirectional data processing capability of up to

20Gbit/s. The maximum interface capacity of the CX600-X1 is

52Gbit/s.

(66)

Overview-Slot Layout

Slot layout of the CX600-X1

Slot layout of the CX600-X2

(67)

Power Supply System

DC Power Supply System is powered by two PSUs, which work in

1+1 backup mode. work in 1+1 backup mode.

(68)

Heat Dissipation System

The CX600-X8 draws in air from the left and exhausts air

from the right.

(69)

Data Plane Architecture of the CX600-X1

NPUs are key parts on the

CX600-X2/X1 and are responsible for data

processing and data switching

between PICs (Physical Interface

Card) and NPUs(Network

Processing Unit)

.

The procedure for data processing is

as follows:

The IP packets sent from PICs and

2x10G interfaces on an NPU

converge at a convergence module.

；

The NP processes the IP packets.

The TM module performs traffic

management on the IP packets.

The Fabric Interface Chip (FIC)

(70)

Data Plane Architecture of the CX600-X2

NPUs are key parts on the

CX600-X2/X1 and are

responsible for data processing

and data switching between PICs

(Physical Interface Card) and

NPUs(Network Processing Unit)

The procedure for data

processing is as follows:

The IP packets sent from PICs and

2x10G interfaces on an NPU

converge at a convergence module.

The NP processes the IP packets. The TM module performs traffic

management on the IP packets.

The Fabric Interface Chip (FIC)

(71)

Integrated Line Processing Unit NPUI-20

The NPUI-20 has the bidirectional 20-Gbit/s forwarding capability,

and all subcards switch data through the NPUI-20. An NPUI-20

provides two 10G Ethernet optical interfaces that can work in the

WAN or LAN mode and can be installed with XFP optical modules.

CX600-X1 chassis can install an NPUI-20.

CX600-X2 chassis can install an NPUI-20.

Page70

(72)

Control Plane

The function of control plane is implemented by the MPU.

MPU can be equipped with a single MPU or double MPUs (in backup

mode).

In the case of double MPUs, the master MPU works and the slave MPU is

in the standby state.

MPUs support two switchover modes: failover and manual switchover.

The MPU integrates multiple functional units. By integrating the system

control and management unit, clock unit, and system maintenance unit,

the MPU provides the functions of the control plane and maintenance

plane.

Page71

(73)

Content

2. CX600-X2/X1 Hardware Introduction

2.1 CX600-X2/X1 Chassis

2.2 CX600-X2/X1 Board

(74)

CX600-X2/X1 Board(1/4)

CX600-X2/X1 supporting boards:

8-Port 100/1000Base-X-SFP (HIC)

8-Port 100/1000Base-X-SFP (HIC, supports 1588v2)

8-Port 100Base-X-SFP(FIC, supports 1588v2)

8-Port 100Base-RJ45(FIC, supports 1588v2)

16-Port E1(75ohm)(FIC)

16-Port E1(120ohm)(FIC)

Auxiliary Interface and 4-Port 100Base-RJ45 (FIC,

supports1588v2)

1-Port Channelized OC-3c/STM-1c POS-SFP (FIC)

(75)

CX600-X2/X1 Board(2/4)

8-Port100/1000Base-X-SFP (HIC)

(76)

CX600-X2/X1 Board(3/4)

8-Port100Base-X-SFP (FIC,supports1588v2)

(77)

CX600-X2/X1 Board(4/4)

16-Port E1(75ohm) (FIC)

Auxiliary Interface and 4-Port100Base-RJ45

(FIC, supports1588v2)

(78)

Self-Test Question About CX600-X2/X1

Hardware

1. The dynamic routing protocol is processed by the ( )

A. Clock board

B. PIC

C. NPU

D. MPU

(79)

Summary

CX600-X16/X8/X3 Hardware

CX600-X16/X8/X3 Chassis

CX600-X16/X8/X3 Board

CX600-X2/X1 Hardware

CX600-X2/X1 Chassis

CX600-X2/X1 Board

(80)

Thank you

www.huawei.com

1 ODX302015 CX600-X 1. Series Products Hardware Introduction ISSUE 1

CX600-X Series

Products Hardware

Introduction

Foreword

CX600-X is a high-end router designed for core and

backbone networks. The CX600-X is positioned as the edge

or convergence router on the IP backbone network.

Based on the powerful Versatile Routing Platform (VRP),

the CX600-X features the following: rich services, large

capacity, high performance, high availability.

Objectives

Upon completion of this course, you will be able to:

Describe CX600-X hardware system architecture

Describe CX600-X boards

Describe CX600-X performance parameters

Describe CX600-X performance parameters

CX600-X chassis and boards

Contents

1. CX600-X16/X8/X3 Hardware Introduction

2. CX600-X2/X1 Hardware Introduction

Contents

1. CX600-X16/X8/X3 Hardware Introduction

2.

CX600-X2/X1 Hardware Introduction

Contents

1.

CX600-X16/X8/X3 Hardware Introduction

1.1 CX600-X16 Chassis

1.2 CX600-X8 Chassis

1.3 CX600-X3 Chassis

1.4 CX600-X16/X8/X3 Boards

Overview-Appearance of CX600-X16

①

③

②

④

⑤

⑥

⑧

⑦

⑧

Switching capacity: 12.58T(bidirectional)

Interface capacity

：

3.2T (bidirectional)

MPU 1 : 1 redundancy

SFU 3

＋

1 redundancy

FAN2

＋

2 redundancy

A Power Entry Modules (PEMs)

Working in 4+4 load balancing mode

4

＋

4 redundancy

③

⑤

①

⑥

⑦

⑧

⑧

⑨

④

Overview-Distributed Architecture

1

2

3

17

18

L

P

U

SFU

4

5

6