High Security
Heavy Duty Shredders
VZ 14.00
Perfect shredding and high performance
in DIN security levels 4 and 5
Perfect shredding and high performance.
The large high security shredders VZ 14.00/4 and VZ 14.00/5 have proven themselves for over 10 years for the destruction of large quantities of data with high and maximum security requirements. The machine is easily loaded via the generously sized loading table with integrated conveyor belt.
Pre-shredding
The shredded material from the primary shredder – 6 x 50 mm particles – falls onto a conveyor belt and is transported directly to the cutting shafts of the security shredder.
Only the combination of primary and security shredder enables such a large throughput at high security levels.
Execution VZ 14.00/4: 2 x 15 mm Security Shredder
The 2 x 15 mm cutter guarantees security level 4 as per DIN 32757-1. Thanks to the subsequent compaction of the fine
particles in the integrated bale press, even the requirements for security level 5 are met. Execution VZ 14.00/5:
2 x 4.5 mm Security Shredder
The security shredder with 2 x 4.5 mm particle size enables compliance with security level 5
as per DIN 32757-1. Thanks to the subsequent compaction
of the particles, the requirements of security level 5 are even exceeded.
High Security Heavy Duty Shredders
VZ 14.00
High Security Heavy Duty Shredders
VZ 14.00
Efficient, thermally protected gear motors
(4.0 + 3.3 kW motor output) and robust drive
Optimum cutting performance thanks to robust,
low-wear blade shafts made of galvanised special steel
Working width: 500 mm;
suitable for the most common EDP formats
Practical additional benefit
■ Separate insertion slot to reduce
volume of small cardboard boxes in the pressing chamber
Professional solution
■ Automatic control of primary and security shredder ■ Parallel operation of shredder and press
■ Electronic fill level monitoring of the press chamber ■ Automatic triggering of the press cycle
■ Shredder can still be loaded during this process ■ Visual signal of the message „Bale ready“ and
simultaneous interruption of the cutting process
■ Integrated automatic oiler for the security shredder
Optimum handling
■ Push-button bale ejection ■ Compact bales
■ Ejection into collection bag for low-dust, clean transport
as well as packaging protected from the elements Standard safety equipment
■ Wide EMERGENCY-STOP bar on feed table for immediate
machine stop in the event of danger
■ Lockable master switch and key-operated switch
■ Safety switch on the service door of the security shredder
for machine stop when the door is opened
■ Overload protection in transfer area between shredder and press ■ Safety switch on the loading door of the press
■ Safety lock on the bale ejection door
■ Safety switch for machine standstill in the event of missing or moved press ■ Motor protection via thermal sensor and overcurrent protection relay
Practical extension: dust extractor
■ Prepared as standard for connection of a dust extractor
■ Significant improvement in room climate and working conditions ■ Space-saving, mobile positioning next to the shredder
Advantageous
■ Sturdy bales and
Transport Packaging ■ Packed in a wooden crate ■ Dimensions L x W x H Shredder 2,490 x 1,360 x 1,730 mm Baler 2,260 x 980 x 940 mm ■ Weight with packaging 1,580 kg
High Security Heavy Duty Shredders
VZ 14.00
VZ 14.00/4 VZ 14.00/5
Security Level DIN 32757-1 Level 4 DIN 32757-1 Level 5 Size of Shreds mm 2 x 15 2 x 4.5
Shredding Capacity1 Sheets 90-100 90-100
Shredding Capacity2 kg/h 250 150
Cutting Speed approx. m/sec 0.24
Working Width approx. mm 500
Press Force approx. kN 80
Bale Weight3 kg 60-80
Noise Level dBA 74
Power Supply Volt 400 / 3ph
Motor Power kW 11.3 (4 kW Pre-Shredder + 3.3 kW Post-Shredder + 4 kW Baler) Dimensions L x B x H mm 3,030 (with bale-ejection flap open 3,660) x 1,200 x 1,670 Weight kg 1,370 1 based on 70 g/m2 A4 paper. Sheet capacities vary depending on quality, weight, grain of paper and sufficient power supply. It may be lower if the voltage is below the rated/nominal value. 2 depending on feeding, material and power supply, with cutters in mint condition 3 depending on material and cutting width
Perfect, easy operation
■ Lockable main switch to protect
against unauthorised use
■ Selection switch for manual/automatic operation
■ Clear, robust buttons for On / Off and Reverse on both cutters ■ Visual operating status displays for both cutters and the press
Trouble-free operation
■ All machine functions controlled via programmable
logic control (PLC)
■ Automatic reverse for both cutters with subsequent
restart in the event of overload
■ Fully automatic control of the complete system in automatic mode
Unique feed technology
■ Integrated conveyor belt transports the material
to the primary shredder shredder
■ Both cutting units easily accessible for maintenance
Optimum all-round safety
■ Comprehensive safety equipment at all important
Installation instructions
intimus VZ 14.00/4 und VZ 14.00/5
High Security Heavy Duty Shredders
Scale 1:40
Dimensions mm [1] Length 3,030 [2] Length with bale ejection flap open 3,660 [3] Height 1,670[4] Inlet height or desk height 1,305
[5] Width 1,200
Required space / distances mm
[1] min. 600 [3] min. 800
[2] min. 1,000 [4] min. 1,200 Position of controls
Power Supply 3 Phase - Power lead = 5.10 m
- 400-415 V / 50 Hz supplied with Cekon CEE 32 A plug, 5-pin - other voltages on request Required Fusing by customer
- Circuit breaker with tripping characteristic C - or fuse gL/gG Classification type 1 as per IEC/EN 60947-4-1 400-415 V / 50 Hz = 35 A slow blow 220-230 V / 50-60 Hz = 40 A slow blow 200 V / 50-60 Hz = 63 A slow blow Shredder: Operator‘s position Baling press: Operator‘s position [1] [2] [3] [4] [1] [3] [4] [5]
