DIN Standards

(1)

List of DIN Standards

Logo of DIN German Institute for Standardization

Contents

1 Identification of standard number and date of issue 2 List by number 2.1 DIN 1-999 2.2 DIN 1000-1999 2.3 DIN 2000-2999 2.4 DIN 3000-3999 2.5 DIN 4000-4999 2.6 DIN 5000-5999 2.7 DIN 6000-6999 2.8 DIN 7000-7999 2.9 DIN 8000-9999 2/10 DIN 10000-14999 2/11 DIN 15000-17999 2/12 DIN 18000-18298 2/14 DIN 18500-18999 2/15 DIN 19000-19999 2/16 DIN 20000-29999 2/17 DIN 30000-39999 2/18 DIN 40000-49999 2/19 DIN 50000-59999 2/20 DIN 60000-69999 2/21 DIN 70000-99999 2/22 DIN EN 1-999 2/23 DIN EN 1000-1999

The list gives an overview of the naming system of the DIN standards with standard number, part of standards and other additives. It also tells about standards, their titles, as well as their validity and possible replacement are collected. In addition to

2/13 DIN 18299-18459 German construction contract procedures - Part C: General technical specifications in construction contracts (ATV)

(2)

2/24 DIN EN 2000-9999 2/25 DIN EN 10000-19999 2/26 DIN EN 20000-59999 2/27 DIN EN 60000-99999 2/28 DIN EN 100000 from 2/29 DIN EN ISO 1-9999 2/30 DIN EN ISO 10000-99999 2/31 DIN IEC

2:32 DIN ISO and ISO / IEC 2:33 DIN VDE

2:34 LN standards (aviation)

3 Weblink

Designation of standard number and date of issue [ Edit ]

At the standard number can be seen which originates a standard:

ISO: (. Eg ISO 10002): Unchanged German takeover of an ISO standard. DIN IEC: (. Eg DIN IEC 60912): Unchanged German takeover of IEC norm.

2:35 VG standards (for "defense equipment", the German Federal Office of Defense Technology and Procurement, Koblenz, published)

DIN: (. Eg DIN 33430 ) DIN standard, published exclusively or mainly of national importance or as a precursor to a supranational document.

DIN CEN / TS or DIN CLC / TS: (. Eg DIN CLC / TS 50459-1): Unchanged German adopting a European Technical Specification.

DIN CWA: (. Eg DIN CWA 14248) Unchanged German takeover of a CEN - or CENELEC Workshop Agreement (Technical Rule).

EN: (. Eg DIN EN 14719) German takeover of a European Standard (EN). European standards must, if they are accepted, are unchanged by the members of CEN and CENELEC.

DIN EN ISO: (. Eg DIN EN ISO 9921): Under the auspices of ISO or CEN resulting standard, which will be published by both organizations.

DIN EN ISO / IEC: (. Eg DIN EN ISO / IEC 7810) German standard based on a European standard, which is based on the International Standard ISO / IEC.

DIN EN ISP: (. Eg DIN EN 10608-6 ISP): German standard based on a European standard, which is based on an international standard profile.

DIN VDE Subjects Electrical, Electronic and Information Technology jointly by DIN and VDE by the DKE processed. See list of DIN VDE standards .

Attention Are DIN standards behind the label "DIN" with another letter - except "VDE" - referred to, these have their own numbering system, for example: DIN 3 standard dimensions, but with DIN EN 3 fire

extinguishers.

A standard part is with a hyphen and the number of the standard part denoted (z. B. Part 1 of EN 3 as DIN EN 3-1). Earlier it was "part 1" advertised or "T. 1 "(abbreviated. Eg DIN 14093 Part 1); Today, this supplement is advertised only on the standard s

The issue date of detection is the calendar month in exact figures for a colon quoted, eg DIN 1301-1. 2002-10, however, shown on the title page with name ausgeschriebenem month of October of 2002.

(3)

List by Numbers [ Edit ]

See also: Category: DIN in alphabetical order of the numbers Notices

The list is not exhaustive.

In order to guarantee the timeliness of the standards listed here she continuously takes the Beuth Verlag be matched. The standard titles are out in force at the time of issue of the relevant standard spelling.

DIN 1-999 [ Edit ]

see list of standards DIN 1 to DIN 499 (the preparation also lists historical standard editions) see list of standards DIN 500 to DIN 999 (the preparation also lists historical standard editions) DIN 1000-1999 [ Edit ]

DIN 1000 steel structures - version, replaced by DIN 18800-7 DIN 1013 Hot rolled round steel

Part 1 of general application, February 2004 replaced by DIN EN 10060 Part 2 for a specific purpose, in February 2004 replaced by DIN EN 10060 DIN 1014 Hot-rolled square steel

Part 1 Steel bars for general purpose February, replaced in 2004 by DIN EN 10059 Part 2 bars, for a specific purpose, in February 2004 replaced by DIN EN 10059

DIN 1015 steel bars, hot rolled steel hexagon February, replaced in 2004 by DIN EN 10061

DIN 1016 Flat products made of steel, hot-rolled strip, hot rolled sheet, November 1996 replaced by DIN EN 10048 DIN 1017 steel bar, hot rolled flat steel

Part 1 of general application, February 2004 replaced by DIN EN 10058 Part 2 for a specific purpose, in February 2004 replaced by DIN EN 10058

DIN 1018 steel bars, hot rolled steel half round and half round flat steel, March 2005 withdrawn without replacement

DIN 1022 steel bars, hot rolled steel angle isosceles sharp edges (LS-steel)

DIN 1024 steel bars, hot rolled round-edged T-steel, January 1996 replaced by DIN EN 10055 DIN 1025 Hot rolled I-beam

Part 1 I-series Part 2 IPB series Part 3 IPBl series Part 4 IPBv series Part 5 IPE-series

DIN 1026 Hot-rolled steel U-profile Part 1 with inclined flange

Until about 1969 maintained a standard to slight changes in their issue date of, the change was noted with an attached small Malkreuz; z. B. means "in March 1953xx" that issued in March 1953 standard has been revised twice slightly. This "cross expenditur

By 1940 standards had some subjects between the word "DIN" and the number one letter code, for. Example BERG for mining, HNA for shipbuilding, LON for the locomotive and Kr for the automotive industry. After the introduction of five-digit standard numbers

DIN 1019 steel bars; Hot rolled bulb flats, weights, dimensions, tolerances, static values, December 1996 replaced by DIN EN 10067

(4)

Part 2 with parallel flanges

DIN 1027 steel bars, hot rolled round-edged Z-steel

DIN 1028 Hot-rolled, isosceles circular edge angle steel, Nov. replaced in 1998 by DIN EN 10056-1 DIN 1029 Hot-rolled, round-edged unequal angle steel, Nov. replaced in 1998 by DIN EN 10056-1 DIN 1041 locksmith hammers

DIN 1042 Sledge Hammers, Demolition Hammers Cross

DIN 1045 structures from concrete , reinforced concrete and prestressed concrete

Part 1 Design and construction, January 2011 replaced by DIN EN 1992-1-1 and EN 1992-3

Part 2 Concrete - Specification, performance, production and conformity - Application rules for DIN EN 206-1 Part 3 Construction - National Annex to DIN EN 13670

Part 4 Supplementary rules for the production and conformity of precast Part 100 brick ceilings

DIN 1048 Testing concrete Part 1 fresh concrete

Part 2 hardened concrete in structures and components

Part 4 Determination of compressive strength of hardened concrete in structures and components Part 5 hardened concrete, separately prepared specimens

DIN 1052 Preparation and execution of timber structures (part 1-3 withdrawn, now DIN EN 1995-1-1) Part 1 Design and construction

Part 2 Mechanical connections

Part 3 wooden houses in panel construction - Design and construction Part 10 Supplementary Provisions

DIN 1053 masonry (withdrawn, now DIN EN 1996-1-1) Part 1 Design and construction

Part 2 Masonry strength classes on the basis of aptitude tests Part 3 reinforced masonry - Design and construction

Part 4 Precast

Part 11 Simplified method for detection of unreinforced masonry Part 12 The construction and design of unreinforced masonry Part 13 Detailed design method for unreinforced masonry

Part 14 Design and construction of masonry made of natural stone Part 100 calculation based on the semi-probabilistic safety concept

DIN 1054 Building - Verification of the safety of earthworks and foundations DIN 1055 Actions on structures

Part 1 Densities and weights of building materials, structural elements and stored materials Part 2 Soil Characteristics

Part 3 equity and imposed load in building Part 4 Wind loads

Part 5 Snow and ice

Part 6 Actions on Silos and tanks Part 7 of the effects of temperature

(5)

Part 8 Actions during execution Part 9 Unusual effects

Part 10 actions due cranes and machinery

Part 100 Basis of structural design, safety concept and design rules DIN 1069 waterslides - Safety requirements and test methods DIN 1072 Road and foot bridges; Loads

Supplement 1 road and foot bridges; Load assumptions; Explanations

DIN 1076 Engineering structures in connection with roads, inspection and testing DIN 1089 Refractories for coke ovens

Part 1 silica bricks - Requirements and testing Part 2 firebricks - Requirements and testing

Part 3 mortar for silica and fireclay bricks; Requirements and testing

DIN 1100 hard materials for cementitious hard aggregate screeds - Requirements and test methods

DIN 1101 Domestic fireplaces for solid fuels - Emission Testing (SPEC) DIN 1159 loops with one side cut tip

DIN 1164 Special cement

Part 10 Composition, specifications and conformity evaluation for cement with low effective alkali content Part 11 Composition, specifications and conformity evaluation for cement with short setting

DIN 1193 hammers made of steel - Technical delivery conditions DIN 1195 eye dimensions for hammers and forging tools

DIN 1229 unit weights for tops and manhole tops for traffic areas

DIN 1236 Concrete elements and buckets for operations; Class A and Class B Part 1 construction, installation and compilations

Part 2 concrete parts Part 3 buckets

DIN 1249 sheet glass in building DIN 1259 glass

DIN 1289 Feuergeschränk for tile; Stoke-hole Füllfeuerung DIN 1301 units

Part 1 unit name, unit characters

Part 1, Supplement 1, unit Similar Names and Emblems Part 2 Commonly employed parts and Multiples

Part 3 conversions for no longer applicable units

DIN 1302 General mathematical symbols and concepts DIN 1304 Symbols

DIN 1305 mass, weight value, force, weight, force, weight, load DIN 1306 density

DIN 1310 Composition of mixed phases (gas mixtures, solutions, mixed crystals); Terms, Symbols

DIN 1101 wood-wool slabs and multi-layer lightweight panels as insulating products for building (invalid, March 2007 replaced by DIN EN 13168 and DIN V 4108-10)

Part 12 Composition, specifications and conformity evaluation for cement with an increased proportion of organic constituents

(6)

DIN 1311 vibrations and vibration systems DIN 1312 Geometrical orientation

DIN 1313 sizes

DIN 1314 print Basic concepts, units DIN 1315 angle

DIN 1318 volume level

DIN 1319 Measurement Technology DIN 1320, Acoustics

DIN 1324 Electric Field DIN 1325 Field

DIN 1332 symbols acoustics DIN 1333 figures

DIN 1335 Geometrical Optics - descriptions and definitions DIN 1338 Formula spelling and math typesetting

DIN 1339 units magnetic variables

DIN 1340 Gaseous fuels and other gases; Types, components, using DIN 1342 viscosity; Newtonian fluids

DIN 1343 reference state, standard state, standard volume DIN 1349 passage of optical radiation by media

Part 1 An optically clear materials, quantities, symbols and units Part 2 optically opaque materials, concepts

DIN 1353 abbreviations of terms

Part 1 Elemental abbreviations, April 1997 replaced by DIN ISO 5261 Part 2 for semi-finished April 1997 replaced by DIN ISO 5261

DIN 1355 time

Part 1 calendar week numbering , date, time; November 1994 back without replacement; Successor to DIN EN 28601 DIN 1356 illustration of lines and hatching in drawings

Part 1 Types, content and general rules for representation Part 6 of buildings and construction

Part 10 drawings reinforcement drawings, in June 1996 replaced by DIN ISO 3766 and DIN ISO 4066 DIN 1357 units of electrical quantities

DIN 1412 Twist Drill High Speed ??Steel - Anschliffformen DIN 1421 branches and numbering in texts

DIN 1422 publications in science, technology, business and administration Part 1 of Manuscripts and typescripts

Part 2 Design of fair copies for Reprographic Processes Part 3 Typographic Design

Part 4 design of research reports DIN 1434 bolts

(7)

DIN 1441 slices, Model coarse, for bolts

DIN 1443 pin without head, Oct. replaced in 1992 by DIN EN 22340 DIN 1444 Clevis pins with head, Oct. replaced in 1992 by DIN EN 22341 DIN 1448 Conical shaft ends with male thread

DIN 1449 Conical shaft ends with internal thread DIN 1450 fonts; legibility

DIN 1451 DIN font

DIN 1455 manuscript (replaces DIN 1451 Supplement 5) May 2001 withdrawn without replacement DIN 1460 Conversion of cyrillic alphabets Slavic languages

DIN 1463 Thesaurus

DIN 1464 loose-leaf publications (-werke); Additional deliveries shape and arrangement DIN 1469 Paßkerbstifte with neck

DIN 1474 Grooved pins plug, Oct. replaced in 1992 by DIN EN 28741 DIN 1478 Turnbuckles made of steel tube or round steel

DIN 1479 Hexagon turnbuckles

DIN 1480 Turnbuckles, forged (open form)

DIN 1481 spring pins (Adapter sleeves), heavy duty, August 1993 replaced by DIN EN 28752

DIN 1501 periodicals; Order feature withdrawn without replacement on the outer envelope, August 1993

DIN 1503 design of scientific journals and trade magazines, January 1987 withdrawn without replacement DIN 1504 literature maps, Feb. 1995 withdrawn without replacement

DIN 1505 Title Information Document

Part 1 withdrawn titles intake of literature, pre-standard, March 2007 without replacement Part 2 Citation

Part 3 directories cited documents (bibliographies)

DIN 1541 Cold-rolled sheet and High-alloy steel, since 1992, replaced by DIN EN 10131 DIN 1543 Hot-rolled from 3 to 150 mm thickness, since 1992, replaced by DIN EN 10029 DIN 1544 Cold-rolled steel strip, November 1996 replaced by DIN EN 10140

DIN 1587 Hexagon domed cap nuts, high

DIN 1588 rail vehicles; Kick handle units; Design notes

DIN 1596 Light Saddles steel einlaschig suit with possibility for rail vehicles

DIN 1683 Rough steel castings - General tolerances, machining allowances; Not for new designs

DIN 1686 Rough castings of gray iron - General tolerances, machining allowances; Not for new designs DIN 1687 Rough castings of heavy metal alloys

Part 1 sand castings - General tolerances, machining allowances

DIN 1502 Rules for the shortening of words in titles and for the shortening of the publication titles of March 2000 withdrawn without replacement

Supplement 1 reduction in the title of journals and similar publications; Abbreviations of words from languages ??with Latin and Cyrillic characters, October 1989 withdrawn without replacement

Part 4 title information of documents: remote recording tracks of audio-visual materials, pre-standard, March 2007 without replacement

DIN 1570 Hot-rolled ribbed steel spring; Dimensions, weights, tolerances, static values; January 2004 replaced by DIN EN 10092-2

(8)

Part 3 die casting, general tolerances, machining allowances Part 4 die casting; General tolerances, machining allowances DIN 1688 Rough castings of light alloys

Part 1 sand castings - General tolerances, machining allowances; Not for new designs Part 3 die casting, general tolerances, machining allowances

Part 4 die casting; General tolerances, machining allowances

DIN 1700 non-ferrous metals , Nomenclature of Designation, May 2000 withdrawn without replacement DIN 1702 nickel anodes

DIN 1707 solders , composition, application, technical specifications, March 1994 replaced by DIN EN 29453 DIN 1708 copper - cathodes and Gußformate May, replaced in 1998 by DIN EN 1976 and DIN EN 1978

DIN 1714 copper-aluminum casting alloys (cast-aluminum bronze) - Casting December, replaced in 1998 by DIN EN 1982 DIN 1716 copper-lead-tin casting alloys (cast tin-lead bronze) - Casting December, replaced in 1998 by DIN EN 19822 DIN 1718 copper alloys - Terms and definitions

DIN 1729 magnesium alloys

DIN 1732 Welding consumables for aluminum and aluminum alloys

DIN 1754 Copper tubes and pipes, nahtlosgezogen, July 2002 replaced by DIN EN 12449 and DIN EN 12451

DIN 1770 rectangular bars of aluminum and aluminum alloys, pressed January, replaced in 1987 by DIN EN 755-5 DIN 1786 installation copper tubes, nahtlosgezogen, May 1996 replaced by DIN EN 1057

DIN 1787 copper - semi-finished products DIN 1804 locknuts; ISO metric fine thread DIN 1810 hook key

DIN 1814 Wrench, adjustable

DIN 1816 Cross hole nuts; ISO metric fine thread DIN 1850 Slide Bushings

DIN 1871 Gaseous fuels and other gases

DIN 1897 Extra short twist drills with straight shank DIN 1910 Welding

Part 1: Definitions, classification of welding processes, Nov. 2002 replaced by DIN ISO 857-1 Part 2: welding, welding of metals, procedures, Nov. 2002 replaced by DIN ISO 857-1

Part 3: welding, welding of plastics, process

Part 4: Arc welding, process, Nov. 2002 replaced by DIN ISO 857-1

Part 5: metal welding, resistance welding, process, Nov. 2002 replaced by DIN ISO 857-1 Part 10: Mechanized arc welding processes, terms, Nov. 2002 replaced by DIN ISO 857-1 Part 11: Materials-related terms for metal welding

Part 12: Manufacturing-related terms for metal welding, Nov. 2002 replaced by DIN ISO 857-1

DIN 1705 copper-tin and copper-tin-zinc alloy castings (cast tin bronze and gunmetal) - Casting December, replaced in 1998 by DIN EN 1982

DIN 1709 copper-zinc casting alloys (cast brass and cast brass Special) - Casting December, replaced in 1998 by DIN EN 1982

DIN 1769 rectangular bars of aluminum and aluminum alloys, drawn with sharp edges, September 1986 replaced by DIN EN 754-5

(9)

DIN 1912 Graphical representation; Welding, soldering

Part 1: Concepts and terms for welded joints, fugues, stitching, June 1999 replaced by DIN EN 12345

Part 2: Working positions, seam inclination angle seam rotation angle, in June 1997 replaced by DIN EN ISO 6947

Part 4: Concepts and Terms for Lötstöße and Seams

Part 5: symbols, dimensioning, ISO 2553, 1984 edition modified December, replaced in 1987 by DIN EN 22553

DIN 1940 internal combustion engines; Reciprocating engines, terms, symbols, units DIN 1942 acceptance tests on steam generators (for determination of efficiencies ) DIN 1943 Thermal acceptance tests in steam turbines (VDI steam Rules)

DIN 1944 acceptance tests on centrifugal pumps (centrifugal pumps VDI-rules), replaced by DIN EN ISO 9806 DIN 1945 displacement compressors

DIN 1946 Ventilation and air conditioning

Part 1 terminology and graphical symbols January, replaced in 2004 by DIN EN 12792 Part 2 Health Technical Requirements May 2005 replaced by DIN EN 13779

Part 3 air-conditioning of passenger cars and trucks Part 4 HVAC systems in hospitals (VDI ventilation rules)

Part 6 residential ventilation; Requirements, performance, acceptance (VDI ventilation rules) Part 7 HVAC systems in laboratories (VDI ventilation rules)

DIN 1960 General requirements for the award of construction contracts (see also VOB, Part A ) DIN 1961 Terms and conditions for the execution of works (see also VOB, Part B )

DIN 1986 Drainage systems for buildings and land Part 3 rules for operation and maintenance

Part 4 Fields of application of sewage pipes and fittings of different materials Part 30 maintenance

Part 100 Additional regulations for DIN EN 752 and DIN EN 12056 DIN 1988 Standard for drinking water installations (TRWI)

Part 1 General (retired)

Part 2 Planning and execution; Components, apparatus, materials (withdrawn)

Part 2, Supplement 1 set of standards and other rules about materials, components and equipment Part 3 Determination of the pipe diameter (withdrawn)

Part 3, Supplement 1 Calculation examples (withdrawn)

Part 4 Protection of drinking water (in conjunction with DIN EN 1717 Protection of Drinking Water) (withdrawn) Part 5 pressure boosting and reduction (withdrawn)

Part 6 fire fighting and fire protection systems (withdrawn) Part 7 Prevention of corrosion and scale formation (withdrawn) Part 8 operation of the plants (withdrawn)

Part 100 Protection of drinking water, drinking water quality; DVGW code of practice

Part 2: Supplement 1: working position, inclination angle seam, seam rotation angle, determining the working positions on the tube (example), June 1997 replaced by DIN EN ISO 6947

Part 5 Supplement 1: symbols, dimensioning, application examples of symbols for seam types according to ISO 2553, December 1987 replaced by DIN EN 22553

DIN 1952 Measurement with orifice plates, nozzles and Venturi tubes in full flow-through tubes of circular cross section (VDI Durchflußmeßregeln) (Replaced with DIN EN ISO 5167-1)

(10)

Part 200 Installation Type A (closed system) - Planning, components, equipment, materials; DVGW code of practice Part 300 Determination of the pipe diameter; DVGW code of practice

Part 500 pressure boosting systems with variable speed pumps; DVGW code of practice

Part 600 drinking water installations in connection with fire fighting and fire protection systems; DVGW code of practice DIN 1989 Rainwater harvesting systems

Part 1 design, implementation, operation and maintenance Part 3 rainwater storage

DIN 1996 Testing of Bituminous Materials for Road Building and Related / Testing of asphalt Part 2 sampling

Part 9 Swelling Test

Part 11 Determination of Marshall stability and Marshall flow Part 13 with a flat punch indentation

Part 14 Determination of particle size distribution of asphalt extracted from minerals Part 15 Determination of the softening point, according to Wilhelmi

Part 16 Determination of the tendency to separate

Part 17 Determination of dimensional stability under heat (deformation value by Nüssel) Part 18 ball drop test according to Herrmann

Part 19 Determination of ductility and adhesion in the joint model Rabe DIN 1999 Separator systems for light liquids

Part 7 Proseparate detergent; Requirements, testing (pre-standard)

Part 100 requirements for the application of separation in accordance with DIN EN 858-1 and EN 858-2

DIN 2000-2999 [ Edit ]

DIN 2000 Central drinking water supply Guidelines for drinking water planning, construction and operation of facilities DIN 2001 drinking water supply from small units and non stationary plants

DIN 2023 metal packaging - fitted lids, round Part 1 dimensions, materials, labeling

Part 2 core teachings Part 3 capping

DIN 2025 doses for sausages

DIN 2032 metal packaging; Screw Caps Blackplate

DIN 2046 bucket for sauerkraut and pickles, cylindrical; withdrawn without replacement DIN 2092 Disc springs , Calculation

DIN 2093 Disc springs, dimensions, quality requirements

DIN 2096 Helical compression springs made of round wire and rod Part 1 Quality requirements for hot formed compression springs

Part 101 Additional requirements for separation in accordance with DIN EN 858-1, EN 858-2 and DIN 1999-100 for light liquids with parts of biodiesel or fatty acid methyl esters (FAME)

Part 1 small systems - Guidelines for drinking water, planning, construction, operation and maintenance of equipment; DVGW code of practice

Part 2 Non stationary units - Guidelines for drinking water, planning, construction, operation and maintenance of equipment; DVGW code of practice

(11)

Part 2 Quality Requirements for Mass Production

DIN 2098 Cylindrical helical springs made from round wire (withdrawn)

Part 1 Dimensions for Cold formed compression springs with 0.5 mm wire diameter Part 2 sizes for cold formed springs below 0.5 mm wire diameter

DIN 2101 typewriter platen roller rocker arm for typewriters

DIN 2107 Typewriter font sizes, spacing, line spacing base (type body type lever for typewriters) DIN 2108 Typewriters (naming the machine types and concepts and classification)

DIN 2112 Alphanumeric keyboards ; Key arrangements for hand-operated typewriter.

DIN 2127 Alphanumeric keyboards; Key arrangement for electromechanically driven typewriters DIN 2137 Alphanumeric Keyboards

DIN 2172 Reamers

Part 1 Technical delivery conditions for reamers with shank Part 2 Technical delivery conditions for slip-reamers

DIN 2197 Taps - Technical delivery conditions for ground Taps speed steel

DIN 2201 Machine tools; Taper shanks with driver for taper size 3 to 6 and metric taper size 80 to 200; Mass DIN 2207 for tool shanks Frässpindelköpfe according to DIN 2201 - Connecting dimensions

DIN 2211 drive elements; Narrow V-belt pulleys Part 1 dimensions, material

Part 2 Examination of the grooves

DIN 2215 Endless belts - Classical V-belts - Dimensions DIN 2216 Finite V-belts; Mass

DIN 2217 drive elements; V-belt pulleys Part 1 dimensions, material

Part 2 Examination of the grooves

DIN 2269 Verification of geometrical parameters - Pins DIN 2275 feeler gauges

DIN 2281 Geometrical product specifications (GPS) - Thread Gutlehrdorne

DIN 2282 Verification of geometrical parameters - Thread Gutlehrenkörper

DIN 2194 Cylindrical helical springs made of round wire and rod - Cold-formed torsion springs (torsion springs) - Quality standard

DIN 2279 Geometrical product specifications (GPS) - Lessons for ISO metric screw threads - gauging of the inner and outer thread; Overview, labeling, marking, application

DIN 2280 Geometrical product specifications (GPS) - thread plug gauges for ISO metric screw threads of general application from 1 mm to 40 mm nominal thread diameter

Part 1 Gutarbeitslehren, testing and setting gauges for ISO metric screw threads of general application from 1 mm to 40 mm nominal thread diameter

Part 2 Gutarbeitslehren, testing and setting play for ISO metric screw threads of general application from 40 mm to 200 mm nominal thread diameter

Part 1 Gutarbeitslehren, testing and setting gauges for ISO metric screw threads of general application from 1 mm to 40 mm nominal thread diameter

Part 2 Gutarbeitslehren, testing and adjusting body for ISO metric screw threads of general application from 40 mm to 200 mm nominal thread diameter

(12)

DIN 2283 Geometrical product specifications (GPS) - Committee thread plug gauges

DIN 2284 Verification of geometrical parameters - thread Committee gauge body

DIN 2330 concepts and terms; General principles

DIN 2332 Naming of internationally equivalent concepts DIN 2340 Short forms for terms and names

DIN 2342 terms of terminology teaching ; Part 1 Basic Concepts

DIN 2345 translation tasks ; December 2006 withdrawn without replacement (see also DIN EN 15038) DIN 2353 soldering compression fittings with cutting ring - Complete fittings and survey

DIN 2391 Seamless precision steel tubes, since 2003, replaced by DIN EN 10305-1

DIN 2395 welded precision steel tubes with rectangular and square cross-section, replaced by DIN EN 10305-5 DIN 2401 Pressure and temperature data

Part 1 terms, pressure ratings, September 1997 replaced by DIN EN 764-1 DIN 2403 Colour codes for pipelines

DIN 2405 pipes in refrigeration and cooling equipment - Marking

DIN 2425 Plans for public utilities, water management and for transmission lines Part 1 pipe network plan of public gas and water supply

Part 2 pipe network plan for district heating Part 3 plans for pipelines, DVGW code of practice Part 4 channel network plan public sewers

Part 5 maps and plans of the Water

Part 6 maps and plans for water engineering, the flood and coastal protection DIN 2429 Graphical symbols for technical drawings, Piping

Part 1 General

Part 2 Functional display

DIN 2430 Piping for pigging systems Part 1 pipes and elbows

Part 3 Gutarbeitslehren and check plugs for ISO metric screw threads over 40 mm up to 250 mm nominal thread diameter for use in precision engineering

Part 1 Committee working gauges, testing and setting plug for metric ISO thread for general application of 1 mm to 40 mm nominal thread diameter

Part 2 Committee working gauges, testing and setting play for ISO metric screw threads of general application from 40 mm to 200 mm nominal thread diameter

Part 3 Committee working gauges and check plugs for ISO metric screw threads over 40 mm up to 250 mm nominal thread diameter for use in precision engineering

Part 1 Committee working gauges, testing and setting gauges for ISO metric screw threads of general application from 1 mm to 40 mm nominal thread diameter

Part 2 Committee working gauges, testing and setting play for ISO metric screw threads of general application from 40 mm to 200 mm nominal thread diameter

Part 3 Committee working gauges and check plugs for ISO metric screw threads over 40 mm up to 250 mm nominal thread diameter for use in precision engineering

With DIN 2413 Seamless steel pipes for oil and water hydraulic systems - Calculation rules for pipes and elbows for dynamic loads

(13)

Part 2 tube connections

Part 3 checks before commissioning

DIN 2440 medium weight threaded pipe , Replaced by DIN EN 10255 DIN 2441 Heavy threaded barrel, Replaced by DIN EN 10255

DIN 2442 threaded pipes with Quality Specifications, nominal pressure from 1 to 100 DIN 2444 galvanized steel tubes, since 1998, Replaced by DIN EN 10240

DIN 2445 Seamless steel tubes for dynamic loads

Part 1 hot-finished tubes for hydraulic systems 100 bar to 500 bar Part 2 precision steel tubes for hydraulic systems 100 bar to 500 bar DIN 2448 Seamless steel tubes, since 2003 Replaced by DIN EN 10220 DIN 2458 Welded steel tubes, boiler tubes, Replaced by DIN EN 10220 DIN 2462 Seamless tubes of stainless steels

Part 1 Dimensions, masses per unit length, in June 1996 Replaced by DIN EN ISO 1127 DIN 2463 Welded tubes made of austenitic stainless steels

Part 1 Dimensions, masses per unit length, in June 1996 Replaced by DIN EN ISO 1127 DIN 2470 gas lines made of steel pipes with maximum operating pressure up to 16 bar Part 1 requirements for components

DIN 2501 flanges

Part 1 connection dimensions, Nov. 2007 Replaced by EN 1092-1 / 2

DIN 2507 screws and nuts for pipelines, January 2000 Replaced by EN 1515-1 DIN 2509 bolts

DIN 2510 Bolted connections with Reduced shank Part 1: Overview, Scope and installation examples

Part 2 Metric thread with great game, nominal dimensions and limits of size Part 3 bolts

Part 4 studs Part 5 hex nuts Part 6 cap nuts

Part 7 expansion sleeves Part 8 threaded holes for studs

DIN 2512 flanges - tongue and groove PN 10 - PN 160, June 2002 Replaced by EN 1092-1 DIN 2513 Flanges - nose and tongue PN 10 - PN 100, June 2002 Replaced by EN 1092-1

DIN 2514 flanges - lead with recess and return PN 10 - PN 100, June 2002 Replaced by EN 1092-1 DIN 2519 steel flanges - Technical delivery June 2002 Replaced by EN 1092-1

DIN 2526 flanges - forms the sealing surfaces, Nov. 2007 Replaced by EN 1092-1 DIN 2527 Blind flanges, PN 06 - PN 100, June 2002 Replaced by EN 1092-1

DIN 2558 Oval threaded flanges, smooth - PN6 DIN 2559 Weld preparation

Part 2 Customize the inside diameter for Circumferential welds on seamless pipes

Part 1 Guidelines for joint preparation, fusion welding of butt joints in steel pipes, May, 2004. Replaced by DIN EN ISO 9692-1

(14)

Part 3 Customize the inside diameter for Circumferential welds on welded pipes

Part 4 Customize the inside diameter for Circumferential welds on seamless tubes of stainless steels DIN 2565 with threaded flanges approach, PN 06, June 2002 Replaced by EN 1092-1

DIN 2566 with threaded flanges approach, PN 10, June 2002 Replaced by EN 1092-1 DIN 2567 with threaded flanges approach, PN 40, June 2002 Replaced by EN 1092-1

DIN 2573 Flanges, clogged for soldering or welding PN 6, June 2002 Replaced by EN 1092-1 DIN 2576 Flanges, clogged for soldering or welding PN 10, June 2002 Replaced by EN 1092-1

Connectors Data slide for boiler tubes DIN 2605 fittings for welding, pipe bends,

Part 1 Decreased utilization, June 2008 Replaced by EN 10253-2 / 4 Part 2 Full utilization, June 2008 Replaced by EN 10253-2 / 4

DIN 2607 pipe bends - Made of copper for welding DIN 2609 steel fittings for welding

DIN 2615 pipe fittings, tees

DIN 2616 pipe fittings, reducers, concentric and eccentric, June 2008 Replaced by EN 10253-2 / 4 DIN 2617 pipe fittings, caps, dimensions, June 2008 Replaced by EN 10253-2 / 4

DIN 2618 steel fittings for welding; Saddles, nominal pressure 16 September 1997 WITHDRAWN without replacement DIN 2627 Welding neck PN 400, June 2002 Replaced by EN 1092-1

DIN 2628 Welding neck PN 250, June 2002 Replaced by EN 1092-1 DIN 2629 Welding neck PN 320, June 2002 Replaced by EN 1092-1

DIN 2630 Welding neck nominal pressure 1 and 2.5, Replaced by EN 1092-1 DIN 2631 Welding neck nominal pressure 6, Replaced by EN 1092-1

DIN 2632 Welding neck nominal pressure 10 Replaced by EN 1092-1 DIN 2633 Welding neck nominal pressure 16 Replaced by EN 1092-1 DIN 2634 Welding neck nominal pressure 25 Replaced by EN 1092-1 DIN 2635 Welding neck nominal pressure 40 Replaced by EN 1092-1 DIN 2636 Welding neck nominal pressure 64 Replaced by EN 1092-1 DIN 2637 Nominal pressure welding neck 100, Replaced by EN 1092-1 DIN 2638 Welding neck PN 160, Nov. 2007 Replaced by EN 1092-1

DIN 2641 Loose flanges - Vorschweißbördel - Smooth league PN 6, June 2002 Replaced by EN 1092-1 DIN 2642 Loose flanges - Vorschweißbördel - Smooth league PN 10, June 2002 Replaced by EN 1092-1 DIN 2655 Loose flanges - Smooth league PN 25, June 2002 Replaced by EN 1092-1

(15)

DIN 2656 Loose flanges - Smooth league PN 40, June 2002 Replaced by EN 1092-1 DIN 2673 Loose flanges with welding PN 10, June 2002 Replaced by EN 1092-1 DIN 2695 Diaphragm Seals welding and weld ring gaskets for flanged connections DIN 2696 flange with sealing lens

DIN 2796 flange with threaded collars, stress. Issue June 1948 WITHDRAWN Standard DIN 2805 Flange with Vorschweißbunden, stress. Withdrawn Edition May 1948 standard DIN 2827 Hose assemblies of stainless steel for chemical substances

DIN 2848 Flanged steel pipes and flanged fittings made of steel and cast iron lining - PN 10, PN 25 and PN 40 DIN 2856 solder fitting , Replaced by DIN EN 1254

DIN 2860 handling systems DIN 2867 for solder fittings

Part 1 angleFrom red brass, May 1984 WITHDRAWN without replacement

DIN 2873 Flanged steel pipes and flanged fittings made of steel with enamel - PN 10 and PN 25

DIN 2880 Application of cement mortar lining for cast iron pipes, steel pipes and fittings DIN 2950 DIN EN 10242 Malleable Replaced by

DIN 2980 steel threaded pipe, August 2000 Replaced by DIN EN 10241

DIN 2981 steel threaded pipe - long thread, August 2000 Replaced by DIN EN 10241

DIN 2982 steel threaded pipe - pipe nipple - barrel nipple, August 2000 Replaced by DIN EN 10241 DIN 2983 steel threaded pipe - bow, August 2000 Replaced by DIN EN 10241

DIN 2986 steel threaded pipe - sockets, August 2000 Replaced by DIN EN 10241 DIN 2987 steel threaded pipe

Part 1 Cross - T - angle, August 2000 Replaced by DIN EN 10241 Part 2 T - angle - Reduced, August 2000 Replaced by DIN EN 10241

DIN 2988 steel threaded pipe - paragraph sleeves, August 2000 Replaced by DIN EN 10241

DIN 2990 steel threaded pipe - double nipple with hexagon - Reducer, August 2000 Replaced by DIN EN 10241 DIN 2991 steel threaded pipe - Plugs - Caps, August 2000 Replaced by DIN EN 10241

DIN 2993 steel threaded pipe - pipe fittings, August 2000 Replaced by DIN EN 10241

DIN 2999 Whitworth pipe threads for tubes and fittings (6 parts), March, 2005 Replaced by DIN EN 10226-1 ... 3 DIN 3000-3999 [ Edit ]

DIN 3110 ended spanner - Test torques nach series C

DIN 3113 Combination spanner with same size each - Test torques series A and C DIN 3114 Einmaulschlüssel - Test torques nach series C

DIN 3122 with male square drive parts for hand-operated sockets DIN 3123 connectors with male square for hand-operated sockets DIN 3124 sockets with square drive for Hexagon, manually operated

DIN 3140 dimensions and tolerances for optical items (2.2000 Replaced by DIN ISO 10110-1 ... 12) Part 1: Presentation, dimension-registration, materials

Part 2: bubbles

DIN 2874 Flanged steel pipes and flanged fittings made of steel and cast iron liner made of PTFE or PFA - Technical delivery conditions

DIN 2875 flanged pipes and flanged fittings made of steel with a lining of hard or soft rubber - Technical delivery conditions

(16)

Part 3: Schlieren Part 4: Tensions Part 5: form errors Part 6: Centering Part 7: Surface defects Part 8: Surface finish Part 9: Surface Coatings

Part 10: defects of surface coatings

Part 11: representation in tabular form (draft) May Replaced in 1998 by ISO 10110-10 DIN 3158 Refrigerant Valves - Safety requirements - testing - Identification

DIN 3159 Flange for Refrigerant fittings to ND 25

DIN 3160 passage shut-off valves for Refrigerant circuits, nominal pressure 25 DIN 3161 Eck shut-off valves for Refrigerant circuits, nominal pressure 25

DIN 3162 Protective caps for valves for Refrigerant circuits, nominal pressure 25 DIN 3163 through control valves for Refrigerant circuits, nominal pressure 25 DIN 3164 position indicator for valves in Refrigerant circuits

DIN 3202 Lengths of Valves

Part 1 flanged, December 1995 Replaced by DIN EN 558-1 Part 4 valves with female thread connection

Part 5 valves with Rohrverschraubungsanschluß DIN 3211 fittings

Part 1 terms and definitions, April 1995 Replaced by DIN EN 736-1 DIN 3220 hand wheels, flat - Hub hole with a tapered square DIN 3223 activation key for fittings

DIN 3230 Technical specifications for valves

Part 1 inquiry, order and delivery, in June 2003 Replaced by DIN EN 12266-1

Part 2 General requirements, June 2003 Replaced by DIN EN 12266-1 and DIN EN 12570 Part 3 compilation of Possible tests, June 2003 Replaced by EN 12266-1 / 2

Part 4 valves for drinking water, requirements and testing

Part 5 valves for gas lines and gas equipment, requirements and tests Part 6 fittings for flammable liquids, requirements and testing

DIN 3236 Durchflußschauglasarmaturen with seal in the force shunt Part 1 Without lining

Part 2 By Email lining

DIN 3237 Durchflußschauglasarmaturen with seal in the main load Part 1 Without lining

Part 2 with plastic liner Part 3 With rubber lining

DIN 3247 Suction strainers with flange without backflow preventer

DIN 3280 Valves for domestic water installations; Unions nominal pressure 10 (with cone seal); Survey DIN 3319 hand-wheels, dished - Hub hole with a tapered square

(17)

DIN 3320 safety valves; Safety Shut

Part 1 terms, sizing, marking; April 2009 retired, DIN EN ISO 4126 and DIN EN 794 recommended Part 3 lengths of safety valves with flanged to PN 40 and up to DN 250

DIN 3321 underground hydrants PN 16 DIN 3322 fire hydrants PN 16

DIN 3334 Heating mixer with flange, ND 6 max. 110 ° C - Three-way mixing valve, four-way mixer, dimensions

DIN 3335 Heating mixer with female thread, ND 6 max. 110 ° C; Three-way mixing valve, four-way mixer, dimensions . To DIN 3336 Heating mixer with welding ends, ND 6 max 110 ° C; Three-way mixing valve, four-way mixer, dimensions DIN 3338 Connections of rotary actuators to valves - clutch size for the dog clutches (Form C)

DIN 3339 Valves - Materials for housing parts

DIN 3341 disk valves for displacement compressors - Suction, pressure valves - Main dimensions, materials, installation DIN 3352 slideshow

Part 1: General Information

Part 5 steel gate valves with internal or external spindle thread isomorphic series DIN 3354 flaps

Part 1: General Information, march Replaced in 1998 by DIN EN 593

Part 2 valves , Tightly closing, resilient seated, cast iron, with flanges, march Replaced in 1998 by DIN EN 593

DIN 3356 valves

Part 1: General Information

Part 2 stop valves made of cast iron, Jan. 2003 Replaced by DIN EN 13789 Part 3 shut-off valves non-alloy steel, Jan. 2003 Replaced by DIN EN 13709 Part 4 stop valves temperature steels, Jan. 2003 Replaced by DIN EN 13709 Part 5 shut off valves stainless steels, Jan. 2003 Replaced by DIN EN 13709

Part 6 WITHDRAWN shut off valves cryogenic steels, draft August 1983 without replacement DIN 3357 Ball Valves

Part 1: General Information for ball valves made of metallic materials Part 2 steel ball valves with full bore, July 2006 Replaced by DIN EN 1983 Part 3 steel ball valves with Reduced bore, July 2006 Replaced by DIN EN 1983

Part 4 ball valves made of non-ferrous metals with full bore, February 2007 Replaced by DIN CEN / TS 13547 Part 5 ball valves made of nonferrous metals, Reduced bore, February 2007 Replaced by DIN CEN / TS 13547 Part 6 ball valves, WITHDRAWN from cast iron with full bore, without replacement in May 1997

Part 7 ball valves, WITHDRAWN from cast iron with Reduced bore, without in May 1997 replacement DIN 3358 Connections of linear actuators to valves - Interface dimensions for flanged

Part 3 valves, tightly closing, resilient seated, steel and cast steel, flanged or butt weld ends March Replaced in 1998 by DIN EN 593

Part 4 valves, tight fitting, steel and cast steel, metal seated, with flanges or welding ends March Replaced in 1998 by DIN EN 593

Part 5 WITHDRAWN butterfly valves, tightly closing, centric, for clamping or flanging with soft sealing body lining, draft March 1999 without replacement

(18)

DIN 3360 gas appliances; Domestic cooking appliances burning gas Part 4 Heizherde

DIN 3360 Domestic cooking appliances burning gas Part 13 covers on the devices

DIN 3363 gas appliances for commercial kitchen equipment Part 3 ceramic-Kochfelder For herd; Requirements and testing DIN 3383 Hose assemblies and connection fittings

Part 1 Safety gas hose assemblies, safety connection fittings Part 2 Hose assemblies for rigid connection

Part 4 Safety gas connection valves and fittings for laboratory hoses and hose assemblies DIN 3384 Hose assemblies of stainless steel - Safety requirements, testing, marking

DIN 3389 Insulating for service lines in the gas and water supply; Ready made ??insulating, requirements and tests DIN 3394 Automatic control valves

Part 1 actuators to back up, blowing and rules for surrounding pressures above 4 bar to 16 bar Part 3 actuators to blow, class 0 for surrounding pressures up to 4 bar

DIN 3401 oiler and oil jars; Main dimensions DIN 3404 Flat grease nipple

DIN 3411 Staufferbüchsen; light duty

DIN 3440 Temperature control and limiting for thermo-technical systems (heating), March, 2003 Replaced by EN 14597 DIN 3444 caps for pipe fittings with welded and threaded ends

DIN 3535 Gaskets for gas supply

DIN 3567 Pipe Clamps for northwest 20 to 500 DIN 3570 U-bolts

DIN 3581 gas pipelines; Street Cap size 1 DIN 3582 gas pipelines; Street Cap size 2 DIN 3760 Radial shaft seals

Withdrawn DIN 3770 O-rings, September 1993 without replacement DIN 3771 O-Rings

DIN 3780 seals; Gland diameter and associated package widths, construction sheet

DIN 3476 accessories and fittings for raw and drinking water - Corrosion protection by EP internal coating of powder coatings (P) or liquid varnishes (F) - Requirements and tests

DIN 3489 Air Couplers - Dog clutch claw 42 mm distance, without locking nut - external thread, internally threaded, trousers and connect coupling, rotating claw coupling, sealing ring

DIN 3502 valves for drinking water installations in land and buildings - Valves straight through - sloping PN 10 (Angle seat valve) shell; DVGW code of practice

DIN 3512 valves for drinking water installations in land and buildings - Valves straight through - shell upright PN 10 (globe valve)

Part 5 sealing materials, rubber, cork and synthetic fibers for gas fittings and gas appliances; Safety requirements and testing

Part 6 Gasket materials based on fibers, graphite or polytetrafluoroethylene (PTFE) for gas valves, gas appliances and gas pipes

(19)

DIN 3840 fitting housing - Strength calculation for internal pressure, Oct. 2004 Replaced by DIN EN 12516-2 DIN 3852 stud - ports for pipe fittings, valves

Part 1 locking screws with metric fine pitch thread, design dimensions Part 2 design dimensions for metric fine thread

DIN 3853 Solderless and brazed tube fittings - threaded stud to the union nuts - Construction Journal DIN 3859 Pipe fittings

Part 1 Technical delivery conditions

Chapter 2 Assembly instructions for solderless fittings with cutting rings nach DIN 2353 and DIN EN ISO 8434-1 DIN 3861 Solderless pipe connections - Cutting Rings - Styles

DIN 3863 tube fittings - Ball Bushings - design and bore shapes U and Y DIN 3870 Solderless and brazed tube fittings - Union nuts series LL DIN 3871 Solderless and brazed pipe fittings, fittings times

DIN 3900 soldering compression fittings with cutting ring - screw-series LL with tapered thread

DIN 3901 soldering compression fittings with cutting ring - screwed with parallel thread for screw-type A DIN 3955 soldering compression fittings with cutting ring - Taper shaft for PTO Form A

DIN 3960 concepts and parameters for spur gears (spur gears) and gear pairs (cylinder gear) with involute DIN 3962 Tolerances for Cylindrical Gear Teeth

Part 1 tolerances for Deviations of individual determinants Part 2 Tolerances for flank line Deviations

Part 3 tolerances for split-range Deviations

DIN 3964 center distance education and Achslagetoleranzen of housings for spur gear DIN 3971 concepts and parameters for bevel gears and bevel gear pairs

DIN 3972 reference profiles of gear cutting tools for involute splines nach DIN 867

DIN 3975 concepts and parameters of cylindrical worm gear pairs with intersecting axes perpendicular Part 1 worm and worm wheel

Part 2 variations

DIN 3979 Tooth Damage on Gear Trains, description, characteristics, causes DIN 3990 Calculation of load capacity of spur gears

Part 1 Introduction and general influence factors Part 2 Calculation of pitting

Part 3 Calculation of tooth

Part 5 endurance limits and material qualities Part 6 Fatigue account

DIN 3998 Denominations on Gears and Gear Pairs Part 1: General terms

Part 2 track gears and gear pairs (cylinder and cylinder gear wheels) Part 3 bevel gears and bevel gear pairs, hypoid gears and Hypoidradpaare Part 4 worm and wheel

DIN 4000-4999 [ Edit ]

DIN 4000 Tangible article characteristics (various standard parts) DIN 4002 Properties and Their scopes for product data exchange

(20)

Chapter 1 Basics

Part 2 Definitions and conceptual information model

Part 3 Content and data-technical definition of feature attributes Part 4 Terminology rules for attributes for elements

Part 5 units for quantitative characteristics

Part 6 of content and information technology definition of the structure Part 7 rules for the formation of the scope of application hierarchy

Part 16 Content and data-technical definition of attributes for elements of units and sizes Part 100 features under www.DINsml.net

Part 101 application classes under www.DINsml.net

DIN 4017 Subsoil - Calculation of basic bearing capacity of shallow foundations DIN 4020 Geotechnical investigations for civil engineering purposes

DIN 4021 Subsoil - exploration by trial pits and boreholes; sampling Replaced January 2007 by DIN EN ISO 22475-1 DIN 4022 subsoil and groundwater, short description, naming and description of soil and rock

Part 2 layers directory for drilling in rock (hard rock) , January 2007 Replaced by DIN EN ISO 22475-1

DIN 4024 machine foundations

Part 1 flexible structures did support machines with rotating masses Part 2 stiffness (rigid) foundations for machinery with periodic excitation DIN 4030 assessment concrete aggressive water, soil and gases

Chapter 1 Basics and limit

Part 2 sampling and analysis of water and soil samples

DIN 4033 drainage and sewerage, and guidelines for execution

DIN 4034 Manholes concrete, steel fiber and reinforced precast concrete Part 2 slots for wells and percolation

Part 10 manhole bases masonry for underground drainage and sewerage - Requirements and tests DIN 4040 Grease separators

Part 100 requirements for the application of separation in accor dance with DIN EN 1825-1 and EN 1825-2 DIN 4044 Hydro Mechanics in Hydraulic Engineering; Terms

DIN 4045 Wastewater Engineering, Basic Concepts DIN 4046 Water supply; term; DVGW code of practice DIN 4047 agricultural water; Terms

Part 1 development of irrigation waters, drainage

Part 2 flood protection, coastal protection, pumping stations Part 3 soil science, soil classification and soil analysis

Part 4 bogs and bog soils

Part 5 improvement and maintenance of water

Part 1 layers directory and drilling without continuous recovery of nucleated samples , January 2007 Replaced by DIN EN ISO 14688-1, ISO 14689-1, DIN EN ISO 22475-1

Part 3 layers directory for drilling with continuous production of cored samples in soil (loose rock) , January 2007 Replaced by DIN EN ISO 22475-1

DIN 4023 Geotechnical investigation and testing - Graphical representation of the results of drilling and other direct outcrops

(21)

Irrigation Part 6 Part 7 erosion control Part 9 drainage, drainage

Part 10 properties of soil as plant habitat ; March 2002 Replaced by DIN 4047-3 DIN 4048 Hydraulic Engineering , Terms

Part 1 dams

Part 2 hydropower plants

DIN 4049 Hydrology (Hydrology) Part 1 Basic Concepts

Part 2 terms of water quality

Part 3 terms for the quantitative hydrology

DIN 4050 Wastewater Engineering (terms and definitions) , Replaced by DIN 2425-4 DIN 4052 Concrete elements and buckets for road gullies

Part 1: General requirements and installation Part 2 compilations and designations

Part 3 concrete parts Part 4 buckets

DIN 4054 Waterway terms

DIN 4055 water pipes; Surface box for underground hydrants; DVGW code of practice DIN 4056 water pipes; Surface boxes for shut-off valves, DVGW code of practice

DIN 4063 signs for civil defense DIN 4065 gas pipelines; Signs DIN 4066 signs for fire brigade

DIN 4067 water; Signs, local water distribution and water pipelines DIN 4068 sewage; Signs

DIN 4069 local gas distribution lines; Signs DIN 4073 Planed boards and planks of pine,

Part 1 degree since March 2005. WITHDRAWN without replacement DIN 4074 sorting of timber by strength

Part 1 softwood lumber

Part 2 Quality Conditions for Building Logs (softwood)

Part 3 devices to support the visual grading of sawn timber; Requirements and testing Part 4 demonstrate the suitability of the apparatus-supported timber sorting

Part 5 hardwood lumber

DIN 4076 terms and symbols used on the wooden area Part 1 wood species , Replaced by DIN EN 13556

DIN 4084 Building - Ground failure calculations DIN 4085 Soil - Calculation of earth pressure DIN 4094 building, field investigations

DIN 4060 pipe joints of sewers and drains with elastomer seals - containment requirements and tests for pipe connections, Elastomeric seals

(22)

Part 1 CPTs October 2013 Replaced by DIN EN ISO 22476-1 Part 2 Bohrlochrammsondierung

Part 3 probing January 2003 Replaced by DIN EN ISO 22476-2 Part 4 wing shear tests

Part 5 hole expansion tests in March 2013 Replaced by DIN EN ISO 22476-4 / 5/7

DIN 4095 drainage for the protection of civil structures, planning, design and execution DIN 4102 Fire behavior of building materials and components

DIN 4103 Non-load bearing partitions Part 1 requirements, testing

Part 2 partitions made of gypsum blocks Part 4 substructure in wood type

DIN 4107 Geotechnical Measurements Chapter 1 Basics

Part 2 extensometer and convergence measurements Part 3 Inclinometer and deflectometer

Part 4 pad pressure measurements

DIN 4108 Thermal protection and energy conservation in buildings Part 2 Minimum requirements for thermal protection

Part 3 Air Conditioned moisture protection, requirements, calculation methods and guidelines for planning and execution Part 4 air tightness of buildings - Requirements, planning and design Recommendations, examples.

Part 7 air tightness of buildings, requirements, design and construction and Recommendations. Examples Part 8 Prevention of mold growth in residential buildings

Part 10 related requirements for thermal insulation materials - Factory made thermal insulation products DIN 4109 Sound insulation in buildings

DIN 4123 Excavations, foundations and underpinnings in the area of ??existing buildings DIN 4124 Excavations and trenches, Slopes, working space widths sheeting,

DIN 4126 Verification of stability of diaphragm walls

DIN 4128 grouted piles (in-situ concrete and composite piles) with small diameter

DIN 4149 Buildings in German earthquake areas - Design loads, analysis and structural design of buildings DIN 4150 shocks in Construction

Part 1 Prediction of vibration parameters Part 2 Effects on persons in buildings Part 3 effects to buildings

DIN 4159 brick ceiling and cast panels - static mitwirkend DIN 4160 brick ceiling - not static mitwirkend

DIN 4172 dimensional coordination in building construction DIN 4185 terms and symbols for screening

Part 1 Woven cloth Part 2 perforated plates

DIN 4140 Insulation work on industrial installations in the industry and building equipment - Execution of thermal and cold insulations

(23)

Part 3 Cloth-like screens, wedge wire screens and grates

DIN 4212 runways of reinforced concrete and prestressed concrete; Design and construction

DIN 4226 Aggregates for concrete and mortar

Part 1 Normal and heavyweight aggregates April 2003 Replaced by DIN EN 12620 Part 2 Lightweight aggregates April 2003 Replaced by DIN EN 12620

Part 100: Recycled aggregates

DIN 4261 Small wastewater treatment systems Part 1 The equipment for sewage treatment

Part 2 small wastewater treatment plants with vented purification stage , October 2005 Replaced by EN 12566-1 / 3 Part 3 systems without wastewater aeration - Operation and Maintenance , May, 2004. Replaced by DIN EN 12566-1 Part 4 plants with wastewater aeration - Operation and maintenance , October 2005 Replaced by DIN EN 12566-3 Part 5 Infiltration of aerobic biologically Treated wastewater

DIN 4262 pipes and fittings for underground drainage of trafficked and civil engineering Part 1 pipes, fittings and Their joints made from PVC-U, PP and PE

Part 3 pipes and fittings made of concrete and its compounds DIN 4301 ironworks slag and ferrous slag in construction

DIN 4312 industrial turbines, steam turbines and gas expansion; Basis for the construction of industrial turbines DIN 4342 gas turbines; standard conditions, standard services, information on operating values

DIN 4420 and working scaffolds - Head Scaffolding Safety requirements

Part 1 scaffolds - Performance requirements, general design, structural design Part 3 Selected types of scaffolding constructions and Their basic versions DIN 4421 scaffolds - analysis, design and implementation

DIN 4512 Photographic sensitometry

Part 3 Determination of the optical density of scattering permeable layers , 1. 1993 Replaced by DIN 4512-7 ... 9 Part 4 Determination of the sensitivity of color reversal films , 2002-06 Replaced by DIN ISO 2240: 1998-06 Part 5 Determination of the sensitivity of color negative films , 2002-06 Replaced by DIN ISO 5800: 1998-06 Part 6 Sensitometric light sources and light sources.

Part 7 Determination of optical density, terms, symbols and markings

Part 8 Determination of the optical density; Geometric conditions for measurements in transmission Part 9 Determination of the optical density; Spectral conditions

Part 10 Determination of optical density; Geometric conditions for reflection measurements at DIN 4567 Ladders - Design for ladders for special professional use

DIN 4220 Soil Site Assessment - Identification, classification and derivation of soil parameters (normative and nominal scaling)

Part 3 surcharge for concrete; Examination of aggregates of dense or porous structure , in February 2002 Replaced by DIN 4226-1 / 2

Part 101 systems without wastewater aeration - Principles for factory production control and external monitoring , October 2005 Replaced by DIN EN 12566-3

DIN 4426 Safety requirements for workplaces and accesses - Design and execution (equipment for maintenance of Constructed facilities)

Part 1 Determination of the sensitivity of black and white negative material for imagewise recordings , 2000-09 Replaced by ISO 6: 1996-02

(24)

DIN 4620 spring steel, hot-rolled, with rounded narrow sides of leaf springs ; January, 2004 Replaced by DIN EN 10092-1 DIN 4701 heat consumption of buildings , Parts 1, 2 and 3 are Replaced by DIN EN 12831

DIN 4702 boiler

Part 1 Definitions, requirements, testing, marking Part 2 Rules for Heating tests

Part 3 special gas boiler with burner without fan

Part 4 boilers for wood, straw and similar fuels; Definitions, requirements, testing Part 6 boilers using gaseous fuels

Part 8 Determination of the standard efficiency and the standard emission factor DIN 4703 Space Heater

Part 1 Dimensions of member radiators Part 3 Conversion of standard thermal output DIN 4704 Thermal testing of heating appliances

DIN 4709 Determination of the standard efficiency for micro-CHP units up to 70 kW of rated load

DIN 4719 residential ventilation - Requirements, performance testing and labeling of air handling units

Part 1 : Terms in the private household sector DIN 4747 district heating systems

Part 1 Safety equipment for substations, stations and domestic systems to be connected to hot-water heating networks DIN 4751 boiler equipment , Replaced by DIN EN 12828

DIN 4752 Hot water heating systems with flow Temperatures higher than 110 ° C

DIN 4754 Heat transfer systems with organic liquids - Safety requirements and testing DIN 4755 Oil firing installations - Technical regulation installation (TRÖ) - Inspection DIN 4760 form Deviations; Concepts, classification system

DIN 4791 heating system; Electrical connector between burner and heat generator DIN 4807 Expansion vessels

Part 1 terms, statutory in provisions; Testing and marking

DIN 4815 Rubber and plastics hoses for LPG Part 1 tubes with and without inserts

Part 2 hoses

Part 3 hoses for filling and draining vehicle tanks

DIN 4710 Statistics meteorological data to calculate the energy requirements for heating and air conditioning systems in Germany

DIN 4724 Plastics piping systems for hot water underfloor and radiator connection - Crosslinked medium density polyethylene (PE-MDX)

DIN 4734 Decorative Fireplaces for liquid fuels - Decorative appliances generate using of ethanol-based liquid or gelled fuel a flame

DIN 4753 Water heaters and water heating systems for drinking and process water - Requirements, marking, equipment and testing

Part 5 Closed expansion vessels with diaphragm for drinking water installations; Requirements, testing, interpretation and labeling; Technical Rules of DVGW

(25)

Part 4 hoses and hose assemblies for fuel gas installations in vehicles

DIN 4844 Graphical symbols - Safety colors and safety signs

Part 1 Design principles for safety signs in workplaces and public areas Part 2 Overview of safety signs

Part 3 Evacuation Maps , December 2010 Replaced by ISO 23601 DIN 4892 Inch - millimeters; Conversion Tables

DIN 4893 millimeters - inches; Conversion tables ... DIN 4895 orthogonal coordinate system

Part 1: General terms

Part 2 differential operators of vector analysis DIN 4896 Simple electrolyte solutions; Symbols

DIN 4902 Industrial trucks, hand vehicles and trailers, running gear, symbols, terms, Explanations DIN 4924 sands and gravels for well - Requirements and tests

DIN 4926 fountain heads of steel - DN 400 to DN 1200

DIN 4943 Graphical layout and documentation of wells and ground water monitoring wells DIN 4971 Straight turning tool with cutting board made of hard metal

DIN 4972 Curved turning tool with cutting board made of hard metal DIN 4973 internal turning tool with cutting board made of hard metal DIN 4974 indoor Eckdrehmeißel with cutting board made of hard metal DIN 4975 peak turning tool with cutting board made of hard metal DIN 4976 width turning tool with cutting board made of hard metal

DIN 4977 Remote forehead turning tool with cutting board made of hard metal DIN 4978 Remote Eckdrehmeißel with cutting board made of hard metal

DIN 4980 remote side turning tool with cutting board made of hard metal DIN 4981 with nose cutting tool insert of cemented carbide

DIN 4991 business forms, framework models for commercial documents (invoices examined as., And orders. Ä.) DIN 5000-5999 [ Edit ]

DIN 5004 business forms - Unit Conversion

DIN 5005 Paper and board - Ringbucheinlagen - hole diameter, hole center distances for the A4 and A5 DIN 5007 Order of character strings

Part 1: General rules for the preparation (ABC Rules) Part 2 Heading rules for the alphabetical order of names

DIN 5008writing and design rules for text processing examined. as thedate format and spelling of numbers DIN 5009 Diktierregeln

Communication Withdrawn DIN 5012 letter, October 2008 without replacement Withdrawn DIN 5013 pendant letter, October 2008 without replacement

DIN 5030 Spectral measurements Part 1 concepts, quantities, measures

Part 2 radiators for spectral irradiance measurements; Selection Criteria

Part 5 Safety trousers connections and hose connections for removal from liquid pipeline systems - Safety requirements, testing and marking

(26)

Part 3 Spectral separation; Terms and labeling features

Part 5 physical detectors for spectral measurement of radiation; term, characteristics, selection criteria DIN 5031 Optical radiation physics and illuminating engineering

Supplement 1 table of contents quantities, symbols and units as well as the index to DIN 5031-1 and -10 Part 1 quantities, symbols and units of radiation physics

Part 2 evaluation of radiation by recipient

Part 3 quantities, symbols and units of lighting technology Part 4 efficiencies

Part 5 temperature terms

Part 6 pupil light intensity as a measure of retinal illumination Part 7 Designation of the wavelength ranges

Part 8 Radiation terms and constants Part 9 luminescence terms

Part 10 Photobiologically effective radiation, quantities, symbols and actions DIN 5032 Photometry

Part 1 Photometric method

Part 2 operating electrical lamps and measuring the CORRESPONDING sizes Part 3 measurement conditions for gas lights

Part 4 measurements on lamps

Part 6 photometer, Terms, characteristics and Their classification, Oct. 2004 Replaced by DIN EN 13032-1 Part 7 Classification of illuminance and luminance measuring instruments

Part 8 Data Sheet for illuminance measuring instruments DIN 5033 color measurement

Part 1 Basic Concepts of colorimetry Part 2 tristimulus system

Part 3 colorimetric Part 4 spectral

Part 5 equals method Part 6 tristimulus method

Part 7 measuring conditions for object colors Part 8 measuring conditions for light sources

Part 9 standard for calibration for colorimetry and photometry DIN 5034 daylight indoors

Part 1: General requirements Part 2 Basics

Part 3 Calculation

Part 4 Simplified determination of minimum window sizes for living rooms Part 5 measurement

Part 6 Simplified determination of dimensions Suitable for skylight openings in roof areas DIN 5035 Artificial lighting

(27)

Part 2 Guideline values ??for workplaces indoors and outdoors, October 2007 Replaced by EN 12464-1 / 2 Part 3 Interior lighting with artificial light; Lighting in hospitals

Part 5 Interior lighting with artificial light, Emergency lighting, August 1999 Replaced by EN 1838 Part 6 lighting measurement and evaluation

Part 8 Task lights; Requirements, Recommendations and testing DIN 5036 Radiometric and photometric properties of materials Supplement 1 Table of Contents and Index

Part 1 terms, key figures

Part 3 methods of measurement for photometric and spectral radiometric characteristics Part 4 Classification

DIN 5037 Photometric evaluation of projectors

Supplement 1. Simplified evaluation for film, television and stage spotlight with Rotationally symmetrical light distribution

DIN 5038 rules on objective photometry (invalid)

DIN 5039 light bulbs, lamps - Concepts and Classification DIN 5040 lamps for lighting purposes

Part 1 Photometric Characteristics and Classification Part 2 interior lights, Concepts and Classification Part 3 outdoor lights, Concepts and Classification

Part 4 lighting headlights; Terms and photometric evaluation variable DIN 5042 combustion gas lamps and lights

Part 1 Classification, terms

Part 2 Ceramic mouthpieces, dimensions Part 3 gas mantle, dimensions

Part 4 gas mantle for street lighting; Requirements and tests Part 5 pilot burner, hanging arrangement, Form A

Part 6 pilot burner, vertical arrangement Part 7 fixed nozzles

Part 8 nozzles and union nuts for air regulation

DIN 5043 Radioactive luminescent pigments and fluorescent colors

Part 1 measurement conditions for the luminance and designation of the pigments Part 2 measurement conditions for the luminance and names of fluorescent colors

DIN 5044Stationary traffic lights; Lighting of roads for vehicular traffic; General quality characteristics and guide values DIN 5045 meter for DIN volumes; Guidelines (invalid)

DIN 5060 Packaging - closure of the tube end

DIN 5065 Packaging - Plastic closures for metallic tubes

Part 4 Interior lighting with artificial light; Specific Recommendations for lighting in educational establishments, October 2007 WITHDRAWN without replacement, since March, 2003 Largely superseded in DIN EN 12464-1

Part 7 Interior lighting with artificial light; lighting in rooms with computer workstations and workplaces with screen support

Supplement 2 simplified evaluation for film, television and stage lights witheachother to one or two vertical planes symmetrical light distribution

(28)

DIN 5090 Packaging - Packaging Bottles DIN 5107 chisel hammer; Cold Chisel DIN 5108 Masonry Hammers

DIN 5111 stems wooden hammers to 2 kg DIN 5112 stems wooden hammers over 2 kg Screw DIN 5117

DIN 5128 rubber hammers DIN 5131 hatchets

DIN 5132 Beilstiele

DIN 5133 chipping hammer DIN 5134 saw blades for wood

Part 1 Technical delivery conditions for Band Saw Blades Part 2 Technical delivery conditions for saw blades

Part 4 Technical specification for circular saw blades made of tool steel Part 5 Technical specification for circular saw blades with carbide cutting of DIN 5135 wooden stems mallet to 2 kg

DIN 5136 Hammers - Technical delivery conditions DIN 5138 Beitelgriffe

DIN 5139 Stechbeitel DIN 5145 Planing DIN 5146 scrub plane

DIN 5157 set Taps - Two-piece set for pipe threads G 1/16 to G 4 and Rp 1/16 to Rp 4 DIN 5194 Tapered Vierkantschäfte to Bohrwindenwerkzeugen for wood

DIN 5200 screws and nuts - angle screwdriver for slotted screws - Dimensions and requirements DIN 5228 flat scraper, Replaced by DIN 8350

DIN 5235 Adjusting pliers

DIN 5254 pliers for retaining rings for shafts DIN 5256 pliers for retaining rings for Bores DIN 5340 terms of physiological optics DIN 5381 Identification colors

DIN 5401 Rolling bearing parts, balls DIN 5402 Rolling bearing parts Sheet 1 cylindrical rollers Sheet 2 rolls (Withdrawn) Sheet 3 needle rollers

DIN 5406 Rolling bearings - Mother fuses, lock washer , Retaining clamp DIN 5412 Cylindrical Roller Bearings

DIN 5415 Rolling bearings - Adapter sleeves DIN 5416 Rolling bearings - Withdrawal

DIN 5418 Rolling bearings; Dimensions for the mounting

(29)

DIN 5425 tolerances for the installation of bearings

DIN 5426 Rolling bearings - running noise of rolling bearings Part 1 Method for measuring the body sound

DIN 5450 standard atmosphere (invalid) DIN 5464 splines wedge flanks - Heavy series

DIN 5471 Machine tools; spline shaft and spline profiles with 4 splines, internal centering, dimensions

DIN 5472 Machine tools; Spline Shafts and Spline Bore Profiles with 6 splines, internal centering, dimensions DIN 5473 logic and set theory; Symbols and concepts

DIN 5474 characters of mathematical logic DIN 5475 complexes sizes

DIN 5477 percent, per mille DIN 5478 standards in graphs DIN 5480 Involute spline shafts Part 1 Basic Concepts

Part 2 pressure angle 30 °, overview

Part 4 pressure angle 30 °, nominal dimensions, metrics, module 1.25 March, 2005 Replaced by DIN 5480-2: 2005-06

Part 6 pressure angle 30 °, nominal dimensions, measurements, Module 2 May, 2005. Replaced by DIN 5480-2: 2005-06

Part 8 pressure angle 30 °, nominal dimensions, measurements, Module 3, March, 2005 Replaced by DIN 5480-2: 2005-06 Part 9 pressure angle 30 °, nominal dimensions, measurements, Module 4, March, 2005 Replaced by DIN 5480-2: 2005-06

Part 12 pressure angle 30 °, nominal dimensions, measurements, modules 8 May, 2005. Replaced by DIN 5480-2: 2005-06

Part 14 pressure angle 30 °, Flankenpassungen, tolerances, March, 2005 Replaced by DIN 5480-1: 2005-06 Part 15 testing and teaching at side fit Modules 2.5

Part 16 pressure angle 30 °, hobs, shaper cutters, broaches DIN 5481 splines with notched edges

DIN 5482 gear hub spline involute profiles and profiles

Part 1 dimensions, in February 1987 WITHDRAWN without replacement

Part 3 Pressure angle 30 °, nominal dimensions, measurements, modules 0.5; 0.6; 0.75; 0.8 and 1 May, 2005. Replaced by DIN 5480-2: 2005-06

Part 5 pressure angle 30 °, nominal dimensions, measurements, Module 1.5, March, 2005 Replaced by DIN 5480-2: 2005-06

Part 7 pressure angle 30 °, nominal dimensions, measurements, Module 2.5, March, 2005 Replaced by DIN 5480-2: 2005-06

Part 10 pressure angle 30 °, nominal dimensions, measurements, Module 5, May, 2005. Shall be Replaced by DIN 5480-2: 2005-06

Part 11 pressure angle 30 °, nominal dimensions, measurements, modules, 6 May, 2005. Replaced by DIN 5480-2: 2005-06

Part 13 pressure angle 30 °, nominal dimensions, measurements, modules, 10 May, 2005. Replaced by DIN 5480-2: 2005-06

(30)

Part 2 WITHDRAWN profiles for hobs, February 1987 without replacement

DIN 5483 Time-dependent variable

DIN 5485naming principles of physical quantities; Compound words with property and basic words DIN 5486 spelling of matrices

DIN 5487 Fourier transform

DIN 5488 nominations for time-dependent Processes (February 1964 invalid) DIN 5489 sense of direction and sign in electrical engineering

DIN 5490 use of words related, specific, Relatively standardized and Reduced. (In July 2002 Replaced by DIN 5485) DIN 5491 Mass Transfer

DIN 5493 Logarithmic quantities and units

Part 1: General principles, quantities and units of Information Theory, July, 2004. Replaced by DIN IEC 60027-3 Part 2 Logarithmic ratios, degree level in Napier and decibel

Part 2, Supplement 1, Logarithmic ratios, levels, characters Note on benchmarks and measuring conditions DIN 5494 size systems and systems of units (invalid)

DIN 5496 thermal radiation of volume sources

DIN 5498 Chemical Thermodynamics; symbol (invalid) DIN 5499 calorific value and the calorific value; Terms DIN 5510 Fire protection of rail vehicles

Part 1 hazard levels, fire safety measures and certification

Part 2 Fire behavior and fire side effects of materials and parts - Classification, requirements and test methods Part 4 Structural design of vehicles; Safety requirements

Part 5 Electrical equipment; Safety requirements

DIN 5699 Chain Strap for conveyors

DIN 5902 tabs for grooveless bottom rails - Dimensions and types of steel DIN 6000-6999 [ Edit ]

DIN 6063 threads, Mainly for plastic containers Part 1 Dimensions of buttress threads

Part 2 trapezoidal thread, dimensions DIN 6075 Packaging - bottles

Part 1 Vichyform 1 Part 2 Vichyform 2

DIN 6080 packaging, reusable wine bottles, 0.75 l burgundy form DIN 6094

Part 3 Packaging - mouth - hole Mouthpieces

Part 8 Packaging - Mouthpieces - Male thread

Part 10 Packaging - Mouth Pieces for wide-mouth glass containers - Wulstrandmundstücke

Part 3 Zahnlücken- and tooth thickness measurement WITHDRAWN without replacement with measuring ball or measuring cylinder, February 1987

Part 6 Accompanying measures; Function of emergency, information systems, fire alarm systems, fire fighting equipment; Safety requirements

Part 5 Product image - Packaging - Mouthpieces - Mouth Pieces for champagne and sparkling wine bottles with plastic and cork stoppers and crown caps