REB500 Exercise Configuration

(1)

EXERCISE

REB500 - CONFIGURATION

► Configure the REB500 In- and Outputs according to

the following I/O list.

► Used the correct Database

► Check the Application accordingly

STATION

_Exercise20

OBJECT/EQUIPMENT

BUSBAR- & STATION PROTECTION

SYSTEM REB500SYS

ENGINEERING DATE

ENGINEER

COMPANY

Total number of pages 9 (incl. this page)

(2)

Date: Signature:

Client

Date: Signature:

General datas

Nominal voltage of the protected station ... kV

Type of installation (double busbar, 1½ system...) ...

 Air insulated (AIS) not applicable

 Gas insulated (GIS) not applicable

Software version V.7.xx: Exercise20.MDB

... ...

Used drawings not applicable

(designation, No. and modification index) ...

... ... ...

Check of power supply

Type of battery grounding not applicable

(Negative grounded, floating, not applicable

symmetrically grounded at high impedance, …)

Measured voltages: not applicable

First battery: Second battery:  not applicable

Plus to minus ... V Plus to minus ... V Plus to ground ... V Plus to ground ... V Ground to minus ... V Ground to minus ... V

Check of auxiliary contacts

Isolator fully “OPEN” Isolator fully "CLOSED"

Auxiliary contact must be closed Auxiliary contact ideally closed Auxiliary contact must be open “Closed” auxiliary

contact (N/O)

Isolation gap

“Open” auxiliary contact (N/C)

Condition of isolator switching sequence fulfilled:  Yes  No not applicable

Remarks: ... ... ... ... ... ... ...

(3)

Date: Signature:

Client

Date: Signature:

Central unit Slot no.

Binary inputs Function/Remarks Checked

OC01 OC02 OC03 OC04 OC05 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 OC06 OC07 OC08 OC09 OC10 OC11 OC12

OC01 External Reset 

OC02 Accept bus image alarm 

OC03 Block Output Relays 

OC04 Block BBP 

OC05 Block BFP 

OC06 Block EFP 

OC07 ...  OC08 ...  OC09 ...  OC10 ...  OC11 ...  OC12 ... 

Tripping and signalling contacts

CR01 1 2 3 4 5 7 6 CR05 8 9 10 CR06 11 12 13 CR07 14 15 16 17 18 CR02 CR03 CR08 CR09 CR04

CR01 Differential current alarm 

CR02 Isolator alarm 

CR03 Switching inhibited 

CR04 Blocked (functions and / outputs) 

CR05 General alarm (sum of all possible remaining alarms) 

CR06 In service 

CR07 EFP trip 

CR08 BFP trip 

(4)

Date: Signature:

Client

Date: Signature: Feeder OHL 10

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OC01 OC02 OC03 OC04 OC05 OC06 OC07 OC08 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OC10 OC11 OC12 OC13 OC14 OC15 OC16 A B 16 17 18 OC09 OC17 OC18 OC19 OC20 16 17 18 OC01 QB1 OPEN  OC02 QB1 CLOSED  OC03 QB2 OPEN  OC04 QB2 CLOSED 

OC05 not used 

OC06 not used 

OC07 QA1 OPEN 

OC08 QA1 CLOSED 

OC09 QA1 CLOSING COMMAND 

OC10 START BFP PHASE R 

OC11 START BFP PHASE S 

OC12 START BFP PHASE T 

OC13 not used 

OC14 not used 

OC15 not used 

OC16 not used 

OC17 not used 

OC18 RESET 

OC19 START BFP PHASE RST (1) 

(5)

Date: Signature:

Client

Date: Signature: Feeder OHL 10

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CR01 CR02 CR03 CR04 CR05 CR06 CR07 CR08 CR09 CR10 CR11 CR12 CR13 CR14 CR15 CR16 C D CR01 not used  CR02 not used  CR03 not used 

CR04 BFP REMOTE TRIP / EFP REMOTE TRIP (1) 

CR05 BFP REMOTE TRIP / EFP REMOTE TRIP (2) 

CR06 BBP / BFP TRIP CB PHASE R 

CR07 BBP / BFP TRIP CB PHASE S 

CR08 not used 

CR09 not used 

CR10 not used 

CR11 BBP / BFP TRIP SIGNAL PHASE R 

CR12 BBP / BFP TRIP SIGNAL PHASE S 

CR13 BBP / BFP TRIP SIGNAL PHASE T 

CR14 not used 

CR15 not used 

(6)

Date: Signature:

Client

Date: Signature: Feeder TRAFO 2

OC05 not used 

OC06 not used 

OC07 QA1 OPEN 

OC08 QA1 CLOSED 

OC10 START BFP PHASE R 

OC11 START BFP PHASE S 

OC12 START BFP PHASE T 

OC13 not used 

OC14 not used 

OC15 not used 

OC16 not used 

OC17 not used 

OC18 RESET 

(7)

Date: Signature:

Client

Date: Signature: Feeder TRAFO 2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CR01 CR02 CR03 CR04 CR05 CR06 CR07 CR08 CR09 CR10 CR11 CR12 CR13 CR14 CR15 CR16 C D CR01 not used  CR02 not used  CR03 not used 

CR04 EFP REMOTE TRIP (1) 

CR05 EFP REMOTE TRIP (2) 

CR06 BBP / BFP TRIP CB PHASE R 

CR07 BBP / BFP TRIP CB PHASE S 

CR08 not used 

CR09 not used 

CR10 not used 

CR14 not used 

CR15 not used 

CR16 BBP / BFP TRIP CB PHASE T 

(8)

Date: Signature:

Client

Date: Signature: Feeder COUPLER

OC05 not used 

OC06 not used 

OC07 QA1 OPEN 

OC08 QA1 CLOSED 

OC10 QB10 OPEN  OC11 QB10 CLOSED  OC12 QB20 OPEN  OC13 QB20 CLOSED  OC14 QB11 OPEN  OC15 QB11 CLOSED  OC16 QB21 OPEN  OC17 QB21 CLOSED  OC18 RESET 

(9)

Date: Signature:

Client

Date: Signature: Feeder COUPLER

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CR01 CR02 CR03 CR04 CR05 CR06 CR07 CR08 CR09 CR10 CR11 CR12 CR13 CR14 CR15 CR16 C D CR01 not used  CR02 not used  CR03 not used  CR04 not used  CR05 not used  CR06 not used  CR07 not used  CR08 not used  CR09 not used  CR10 not used 

CR14 not used 

CR15 not used 